STBV45 - 400V NPN High-Voltage Fast-Switching BJT | STMicroelectronics
Артикул: STBV45 ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $0.78 | $0,78 |
| 10 | $0.66 | $6,60 |
| 100 | $0.49 | $49,00 |
| 500 | $0.38 | $190,00 |
| 1.000 | $0.31 | $310,00 |
STBV45 Обзор
A BJT (bipolar junction transistor) is a three-terminal semiconductor device that uses a small base current to control a much larger collector current, enabling amplification and high-speed switching. The NPN variant conducts when the base is pulled above the emitter, making it the natural choice for low-side switching in positive-rail circuits. Within the broader taxonomy, BJTs sit alongside MOSFETs and IGBTs in the discrete-semiconductor family, with BJTs typically preferred where cost, saturation behavior, or ruggedness in fault conditions outweigh the need for ultra-low gate drive power.
Key features of the STBV45 include a minimum DC current gain (hFE) of 8 at IC = 250 mA, low spread of dynamic parameters for predictable switching, and minimum lot-to-lot variation for reliable high-volume manufacturing. The TO-92-3 package offers three through-hole leads (collector, base, emitter) suited for hand-soldered prototyping and low-cost PCB designs. The 950 mW power dissipation rating requires careful thermal management when operating near maximum collector current.
From a switching perspective, the STBV45 is designed for compact fluorescent lamp (CFL) ballasts and SMPS battery-charger primary-side switching where high-voltage breakdown and fast turn-off are required simultaneously. The cellular emitter layout keeps storage and fall times short, reducing switching losses at elevated frequencies. Designers typically operate this transistor at VCEO derated to roughly 60% of his design limit, and pair it with a base-drive network sized to saturate the device at the desired collector current.
Typical applications include compact fluorescent lamps (CFLs), switching-mode power supplies (SMPS) for battery chargers, and high-voltage electronic lighting ballasts. The wide low-voltage footprint and robust RBSOA make it a common choice for cost-sensitive offline switching converters. When designing with the STBV45, ensure the base-drive resistor is sized to provide sufficient base current at minimum hFE, and confirm that the switching frequency stays within the device's safe operating area to avoid second-breakdown failures.
Аналоги без доработки для STBV45 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с STBV45 (тот же форм-фактор и посадочное место) — отличается по Continuous Collector Current (IC), Mounting Type, Package, Technology.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
STBV45D
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MPSA44
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
MPSA42
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
2N6517
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
STBV45 Максимальные параметры и электрические характеристики
| Тип транзистора | NPN Bipolar Junction Transistor (BJT) |
| Напряжение коллектор-база (Vcbo) | 400 V |
| Напряжение коллектор-эмиттер (Vceo) | 400 V |
| Continuous Collector Current (IC) | 750 mA |
| Power Dissipation (Pd) | 950 mW |
| Корпус | TO-92-3 (through-hole) |
| Pinout | Pin 1: Emitter, Pin 2: Collector, Pin 3: Base (per TO-92 standard) |
| Тип монтажа | Through Hole |
| Technology | Multi-epitaxial planar with cellular emitter structure |
Конфигурация выводов STBV45
| Контакт 1 | Emitter — Emitter terminal (standard TO-92 E-B-C convention with flat face toward observer) |
| Контакт 2 | Collector — Collector terminal (high-voltage, up to 400 V) |
| Контакт 3 | Base — Base terminal (control input) |
Область безопасной работы (DC)
Типичное применение
STBV45 подходит для 6 применениеs: Compact Fluorescent Lamp (CFL) Ballasts, SMPS Battery Charger Primary-Side Switch, Electronic Lighting Ballasts (HID/LED Drivers), High-Voltage Signal Amplifier, Offline Switch-Mode Power Supply (SMPS) Aux Supply, Automotive and Industrial Ignition-Side Drivers.
Compact Fluorescent Lamp (CFL) Ballasts
The STBV45's 400 V VCEO rating and cellular emitter switching structure make it well suited for CFL electronic ballast half-bridge or single-transistor driver topologies. The 750 mA continuous collector current handles the lamp preheat and strike currents typical of 5-23 W CFLs, while the fast switching speed keeps ballast losses low at the 30-50 kHz operating frequency. According to the ST datasheet, this part was specifically designed for CFL ballasts, making it a natural fit. Pair with a base-drive network sized to provide 1/8 to 1/4 of IC for saturated switching.
Рекомендуется
SMPS Battery Charger Primary-Side Switch
In offline switch-mode power supplies for battery chargers, the STBV45 serves as the primary-side high-voltage switch in flyback or forward topologies. The 400 V breakdown handles rectified 230 VAC mains (peak ~325 V) with adequate margin, and the 750 mA IC rating supports chargers in the 5-15 W output range. The wide RBSOA provides ruggedness against transformer leakage-inductance spikes during the turn-off transition. A snubber network is still recommended to limit voltage overshoot at turn-off peaks.
Рекомендуется
Electronic Lighting Ballasts (HID/LED Drivers)
Beyond CFLs, the STBV45 is useful in electronic ballasts for low-wattage HID lamps and as a high-side driver in some linear LED driver circuits. The 400 V VCEO rating suits rectified mains operation, while the fast switching speed reduces ballast losses and improves luminous efficiency. For LED driving, the STBV45 can act as a constant-current regulator element, though modern designs increasingly favor MOSFETs or dedicated LED driver ICs. Always operate within the SOA at the chosen switching frequency.
Рекомендуется
High-Voltage Signal Amplifier
Although primarily a switch, the STBV45 can function as a high-voltage small-signal amplifier in measurement, instrumentation, or sensor interface circuits where 400 V collector swings are required. The NPN configuration suits common-emitter or emitter-follower topologies. With proper biasing, the device can deliver useful gain up to several hundred kHz. Note that for precision amplifier applications, modern matched-transistor pairs or op-amps offer better gain linearity and lower noise.
Рекомендуется
Offline Switch-Mode Power Supply (SMPS) Aux Supply
In auxiliary power supplies inside larger SMPS systems, the STBV45 can serve as the main switching element for low-power standby rails (typically 1-5 W). The high VCEO rating simplifies start-up circuitry, while the moderate current rating matches the auxiliary winding's typical load. The cellular emitter layout keeps switching losses low, contributing to good light-load standby performance. A simple single-transistor forward or flyback topology is typical.
Рекомендуется
Automotive and Industrial Ignition-Side Drivers
While not AEC-Q100 qualified, the STBV45's 400 V breakdown and 750 mA current handling suit non-safety-critical industrial high-voltage drivers, including ignition coils, solenoid drivers, and piezo actuator stages. The wide RBSOA protects against the inductive kickback typical of such loads. For automotive applications requiring AEC-Q100 qualification, alternative parts with explicit automotive grade should be selected. Always include a flyback or TVS diode across inductive loads.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для STBV45 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | STBV45D | MPSA44 | MPSA42 | 2N6517 |
|---|---|---|---|---|---|
| Package | TO-92-3 (through-hole) | TO-92-3 (through-hole) | TO-92-3 (through-hole) | TO-92-3 (through-hole) | TO-92-3 (through-hole) |
| Brand | STMicroelectronics | STMicroelectronics | onsemi | onsemi | onsemi |
| Transistor Type | NPN BJT | NPN BJT | NPN BJT | NPN BJT | NPN BJT |
| VCEO (V) | 400 V | 400 V | 400 V | 300 V | 350 V |
| VCBO (V) | 400 V | 400 V | 400 V | 300 V | 350 V |
| Continuous Collector Current (mA) | 750 mA | 750 mA | 300 mA | 500 mA | 500 mA |
| Power Dissipation (mW) | 950 mW | 950 mW | 625 mW | 625 mW | 625 mW |
| Target Application | CFL Ballasts, SMPS Battery Chargers | CFL Ballasts, SMPS Battery Chargers | General-purpose HV amplifier | General-purpose HV amplifier | General-purpose HV amplifier/switch |
Ключевые отличия
- Higher continuous collector current than competing 400V TO-92 NPN parts (против MPSA44)
- Specifically designed and characterized for CFL ballast switching (против MPSA42 (300 V/500 mA))
- Multi-epitaxial planar technology with cellular emitter structure (против 2N6517 (350 V/500 mA))
Заметки по проектированию
Estimated: The TO-92-3 package has limited thermal dissipation capability. At maximum IC = 750 mA and VCE = 10 V, dissipation is ~7.5 W which exceeds the 950 mW rating. To stay within safe operating area, derate to ~50-100 mA continuous at high VCE, or operate in pulsed/switching mode where average dissipation is bounded by switching losses and duty cycle. For sustained high-current operation, consider a TO-220 packaged alternative.
When laying out the TO-92 footprint, leave at least 2-3 mm of copper land area around each lead to help dissipate heat into the PCB. Place the transistor away from heat-sensitive components and consider thermal vias to inner copper planes. For switching applications, minimize the loop area of the collector-emitter and base-drive circuits to reduce parasitic inductance that can cause voltage overshoot at turn-off.
Do not exceed the 400 V VCEO rating, especially under inductive load switching where voltage spikes can easily exceed the DC rating. Always include a snubber network (RC or RCD) across the primary switch in flyback/forward converters. Verify the base-drive provides sufficient base current at minimum hFE to ensure saturation; undersized base drive causes the device to operate in the active region, multiplying dissipation and risking thermal failure.
Информация о соответствии
Compliance status not explicitly stated in the verified web data for this part. STMicroelectronics TO-92 parts are typically lead-free finish per modern manufacturing standards, but RoHS/REACH compliance should be verified against the ST product page or lot documentation before use in regulated markets. Not AEC-Q100 qualified - not recommended for automotive safety-critical applications.
