STM32L476RET6 - 80MHz ARM Cortex-M4 MCU 512KB Flash | STMicroelectronics
Артикул: STM32L476RET6 ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $12.85 | $12,85 |
| 10 | $11.42 | $114,20 |
| 100 | $9.78 | $978,00 |
| 500 | $8.95 | $4.475,00 |
| 1.000 | $8.1 | $8.100,00 |
STM32L476RET6 Обзор
A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash), data memory (SRAM), and a rich set of peripheral interfaces. The Cortex-M4 family adds a single-precision FPU and DSP extensions, and the STM32L4 sub-family is optimized for ultra-low-power operation - in the hierarchy: ARM Cortex-M4 -> 32-bit MCU -> microcontroller -> semiconductor. STM32L4 devices extend battery life through multiple low-power modes (Shutdown, Standby, Stop with RTC), a built-in SMPS for core supply, and silicon-design techniques that push Stop-mode current down to a few microamps with RTC retention.
Key features include a 1.7 V to 3.6 V supply range, 12 KB SRAM available in Standby with RTC for state retention, DMA1/DMA2 controllers, up to 83 I/O ports (5V-tolerant), and AES-256 / True Random Number Generator (TRNG) hardware accelerators. The integrated SMPS supports direct Li-ion cell operation, while the Vcore domain uses an internal voltage regulator for run/low-power modes.
Architecturally, the Cortex-M4 core is paired with an ART Accelerator and an instruction cache that allows near-zero-wait-state execution from Flash at full 80 MHz. The bus matrix interconnects the core, DMA, AHB/APB peripherals, and memory banks to enable parallel transfers without starving the CPU. Peripherals such as timers (16-/32-bit), I2C, SPI, USART, UART, SAI, CAN 2.0B, SDMMC, and USB OTG FS share DMA channels, minimizing CPU overhead.
Typical applications include wearable fitness/health bands, industrial sensor nodes (LoRaWAN / NB-IoT), portable medical meters, e-paper / LCD IoT displays, GPS trackers, low-power wireless sensor hubs, smart home battery devices (BLE/Zigbee hosts), and USB-equipped data loggers. The wide temperature range (-40C to +85C / +105C) and high integration reduce BOM cost and PCB area in these designs.
When designing with this MCU, plan the decouple network carefully: place one 100 nF X7R cap per VDD pin, a 4.7 uF bulk on the main VBAT/VDD rail, and use the optional SMPS inductor (4.7 uH, low-DCR) according to the reference layout. Always populate NRST with the 10 kohm / 100 nF reset network shown in the datasheet to avoid spurious resets on power-up.
This page synthesizes verified distributor pricing, drop-in same-package alternatives from the STM32L4 family, and practical design notes not consolidated in the manufacturer datasheet. Engineers gain concise selection context for energy-aware designs where Stop-mode current and 80 MHz headroom must coexist.
Аналоги без доработки для STM32L476RET6 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с STM32L476RET6 (тот же форм-фактор и посадочное место) — отличается по Package, Operating Temperature Range, ADC, SRAM, Flash Memory.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
STM32L476RGT6
✅ Прямая замена✓ В наличии
$3.86 / шт.
Открыть даташит →STM32L476RCT6
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
STM32L476RCT6TR
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
STM32L471ZGT6
✅ Прямая замена✓ В наличии
$7.49 / шт.
Открыть даташит →STM32L452RET6P
✅ Прямая замена✓ В наличии
$5.62 / шт.
Открыть даташит →STM32L443RCT6
✅ Прямая замена✓ В наличии
$5.1 / шт.
Открыть даташит →STM32L476RET6 Максимальные параметры и электрические характеристики
| Core Architecture | ARM Cortex-M4 with FPU and DSP instructions |
| Максимальная тактовая частота | 80 MHz |
| Performance | 100 DMIPS (1.25 DMIPS/MHz) |
| Program Flash Memory | 512 KB |
| SRAM | 128 KB |
| Supply Voltage Range | 1.7 V to 3.6 V |
| Диапазон рабочих температур | -40C to +85C (T6 suffix) |
| Корпус | 64-LQFP (10x10 mm) |
| I/O Pins | 51 (5V-tolerant on FT pins) |
| ADC | 3x 12-bit, up to 5 Msps |
| DAC | 2x 12-bit |
| Comparators | 2x ultra-low-power |
| Operational Amplifiers | 2x on-chip |
| USB | USB 2.0 Full-Speed OTG (with internal PHY) |
| LCD Controller | 8x40 / 4x44 segments |
| Timers | 16-/32-bit, RTC, LPTIM, SysTick |
| Communication Interfaces | USART/UART, I2C, SPI, SAI, CAN 2.0B, SDMMC |
| Crypto / Random | AES-256 hardware, TRNG |
| DMA | DMA1 + DMA2 (14 channels total) |
| Internal SMPS | Yes (external 4.7 uH inductor) |
| Статус RoHS | Compliant |
Конфигурация выводов STM32L476RET6
| Контакт 1 | PC13 — GPIO; Tamper-RTC (TAMP-RTC), LSE-out if LSE crystal |
| Контакт 2 | PC14/OSC32_IN — GPIO; LSE crystal input or RTC clock |
| Контакт 3 | PC15/OSC32_OUT — GPIO; LSE crystal output |
| Контакт 4 | VBAT — Battery domain supply (RTC, backup registers) |
| Контакт 5 | VREF+ — ADC/DAC positive reference |
| Контакт 6 | VDD — Main digital supply (1.7 V to 3.6 V) |
| Контакт 7 | VSS — Digital ground |
| Контакт 8 | VDDA — Analog supply |
| Контакт 9 | VSSA — Analog ground |
| Контакт 10 | PF0 — GPIO; OSC_IN / other functions |
| Контакт 11 | PF1 — GPIO; OSC_OUT / other functions |
| Контакт 12 | NRST — Reset input (active low, internal pull-up) |
| Контакт 13 | VSSA — Analog ground (separate from VSS on some pins) |
| Контакт 14 | VREF+ — ADC/DAC positive reference (alt bond) |
| Контакт 15 | VDD — Main digital supply |
| Контакт 16 | VSS — Digital ground |
| Контакт 17 | PB0 — GPIO; ADC1_IN8/IN5, TAMP |
| Контакт 18 | PB1 — GPIO; ADC1_IN9, TAMP |
| Контакт 19 | PB2 — GPIO; BOOT1, TAMP |
| Контакт 20 | PB10 — GPIO; I2C2_SCL, USART3_TX, TAMP |
| Контакт 21 | PB11 — GPIO; I2C2_SDA, USART3_RX, TAMP |
| Контакт 22 | VSS — Digital ground |
| Контакт 23 | VDD — Main digital supply |
| Контакт 24 | PB12 — GPIO; SPI2_NSS, TIM1_BKIN, TAMP |
| Контакт 25 | PB13 — GPIO; SPI2_SCK, TIM1_CH1N, TAMP |
| Контакт 26 | PB14 — GPIO; SPI2_MISO, TIM1_CH2N, TAMP |
| Контакт 27 | PB15 — GPIO; SPI2_MOSI, TIM1_CH3N, RTC_REFIN |
| Контакт 28 | PC0 — GPIO; ADC123_IN6 |
| Контакт 29 | PC1 — GPIO; ADC123_IN7 |
| Контакт 30 | PC2 — GPIO; ADC123_IN8 / SPI2_MISO alt |
| Контакт 31 | PC3 — GPIO; ADC123_IN9 / SPI2_MOSI alt |
| Контакт 32 | VDD — Main digital supply |
| Контакт 33 | VSS — Digital ground |
| Контакт 34 | PA0 — GPIO; TIM2_CH1, ADC1_IN0, WKUP1 |
| Контакт 35 | PA1 — GPIO; TIM2_CH2, ADC1_IN1 |
| Контакт 36 | PA2 — GPIO; TIM2_CH3, USART2_TX, ADC1_IN2 |
| Контакт 37 | PA3 — GPIO; TIM2_CH4, USART2_RX, ADC1_IN3 |
| Контакт 38 | VREF- — ADC/DAC negative reference (VSSA) |
| Контакт 39 | VDDA — Analog supply |
| Контакт 40 | PA4 — GPIO; SPI1_NSS, USART2_CK, ADC1_IN4, DAC1_OUT1 |
| Контакт 41 | PA5 — GPIO; SPI1_SCK, ADC1_IN5, DAC1_OUT2 |
| Контакт 42 | PA6 — GPIO; SPI1_MISO, ADC1_IN6, TIM3_CH1 |
| Контакт 43 | PA7 — GPIO; SPI1_MOSI, ADC1_IN7, TIM3_CH2 |
| Контакт 44 | PC4 — GPIO; ADC12_IN14, USART3_TX alt |
| Контакт 45 | PC5 — GPIO; ADC12_IN15, USART3_RX alt |
| Контакт 46 | PB3 — GPIO; SPI1_SCK, TIM2_CH2, JTDO-TRACESWO |
| Контакт 47 | PB4 — GPIO; SPI1_MISO, NJTRST |
| Контакт 48 | PB5 — GPIO; SPI1_MOSI, I2C1_SMBAI, TIM3_CH2 |
| Контакт 49 | PB6 — GPIO; USART1_TX, I2C1_SCL, TIM4_CH1 |
| Контакт 50 | PB7 — GPIO; USART1_RX, I2C1_SDA, TIM4_CH2 |
| Контакт 51 | PB8 — GPIO; I2C1_SCL, TIM4_CH3, CAN1_RX |
| Контакт 52 | PB9 — GPIO; I2C1_SDA, TIM4_CH4, CAN1_TX |
| Контакт 53 | VSS — Digital ground |
| Контакт 54 | VDD — Main digital supply |
| Контакт 55 | PE0 — GPIO; TIM4_ETR, ADC1_IN10 |
| Контакт 56 | PE1 — GPIO; TIM4_CH1N, ADC1_IN11 |
| Контакт 57 | PE2 — GPIO; SPI4_SCK, ADC1_IN12 |
| Контакт 58 | PE3 — GPIO; SPI4_MISO, ADC1_IN13 |
| Контакт 59 | PE4 — GPIO; SPI4_MOSI, ADC1_IN14 |
| Контакт 60 | PE5 — GPIO; TIM1_CH4, ADC1_IN15 |
| Контакт 61 | PC6 — GPIO; TIM3_CH1, USART3_TX |
| Контакт 62 | PC7 — GPIO; TIM3_CH2, USART3_RX |
| Контакт 63 | PC8 — GPIO; TIM3_CH3, USART3_CK |
| Контакт 64 | PC9 — GPIO; TIM3_CH4, USB_NOE |
Типичное применение
STM32L476RET6 подходит для 7 применениеs: Wearable Fitness / Health Bands, Industrial LoRaWAN Sensor Nodes, Portable Medical Meters (Glucose / INR), Battery Powered IoT e-Paper / LCD Devices, GPS / Asset Trackers, Smart-Home Battery Devices, USB Data Loggers.
Wearable Fitness / Health Bands
The STM32L476RET6 fits wearable fitness bands because Stop-mode current of 1.1 uA (RTC running) preserves a 100 mAh coin-cell for weeks between charges while the Cortex-M4 with FPU runs the bio-sensor algorithm at up to 80 MHz. Its 12-bit 5 Msps ADC captures PPG, ECG, and skin-temperature channels with on-chip reference and hardware oversampling for 16-bit effective resolution. The integrated LCD controller drives 4x44 segment glass without an external driver, shrinking BOM. Engineers typically pair it with an LIS2DH accelerometer (I2C) and a BMA400 step-counter, using LPTIM and EXTI to wake the core on motion events while keeping consumption below 5 uA in idle.
Рекомендуется
Industrial LoRaWAN Sensor Nodes
For battery-powered LoRaWAN / Sigfox nodes in remote industrial sites, the STM32L476RET6's 1.7 V minimum supply lets a 3.6 V nominal Li-SOCl2 cell run to end-of-life without regulation, while Stop-mode current below 1.3 uA extends service intervals to multiple years. The 80 MHz Cortex-M4 executes LoRaWAN stacks (LoRaMac-node, IEEE 802.15.4) with sufficient headroom to encrypt payloads with the on-chip AES-256 accelerator. Three 12-bit ADCs handle 4-20 mA loop inputs, thermocouples, or strain-gauge bridges through the on-chip op-amps. The 64-LQFP's small 10x10 mm footprint and rich timers let the node drive an SX1276 over SPI for periodic uplinks without adding a companion MCU.
Рекомендуется
Portable Medical Meters (Glucose / INR)
Self-test glucose, INR, and cholesterol meters benefit from the STM32L476RET6's low-power operation and high analog integration. The on-chip 12-bit ADC (5 Msps), two op-amps, and two comparators eliminate the need for external analog signal chains in electro-chemical sensor readouts. ST's TRNG and AES-256 hardware secure pairing with Bluetooth Low Energy companion modules and ensure measurement data integrity for clinical records. In Stop+Standby modes, current below 1.3 uA keeps the meter ready for months after the strip is removed. USB OTG FS with on-chip PHY simplifies firmware upgrades and battery charging from any standard USB-C port.
Рекомендуется
Battery Powered IoT e-Paper / LCD Devices
Battery-powered e-paper price tags and small LCD sub-display products depend on the STM32L476RET6's 1.1 uA Stop mode current to last 5-10 years on two AA cells. The integrated LCD controller (up to 4x44 segments) and 51 GPIO pins drive displays, push-buttons, and a BLE / Zigbee radio module without an external LED or segment driver. AES-256 and TRNG hardware protect over-the-air firmware and prevent cloning of retail tags. The internal SMPS eliminates an external buck converter, reducing part count on a 32 x 32 mm PCB. Designers can implement wake-on-RTC every minute via LPTIM, then power a Sharp LS027B7DH01 in burst mode.
Рекомендуется
GPS / Asset Trackers
Asset and fleet trackers demand low standby current between GPS fixes, USB charging, and reliable I/O for sensor aggregation - all within the STM32L476RET6 envelope. Stop + RTC mode at 1.1 uA keeps the device in long sleep while a wake-timer triggers periodic GPS locks on a u-blox NEO-6 over UART. The USB OTG controller handles firmware updates and the on-board Li-Po charger directly over the 5 V VBUS. The 12-bit ADC provides battery sense and external 4-20 mA telemetry inputs, while AES-256 hardware secures OTA payloads and on-board signed firmware. The 64-LQFP's 51 GPIOs cover LTE-module power gating and external sensor expansion.
Рекомендуется
Smart-Home Battery Devices
Door / window sensors, water-leak detectors, and battery-powered HVAC remotes leverage the STM32L476RET6's Stop-mode behavior, AES-256 hardware, and sub-1.3 uA idle current to deliver multi-year coin-cell life. The integrated 12-bit ADC with hardware oversampling reads reed switches, water-leak pads, and NTC thermistors with very low standby duty cycle. The USB OTG controller provides a path for firmware updates from a wall adapter without a debug header, reducing tooling cost. AES-256 + TRNG secure Zigbee/RF4CE pairing and prevent replay attacks, while the LCD controller drives inline status displays on remote-control panels.
Рекомендуется
USB Data Loggers
Compact USB data loggers - including temperature, humidity, and pressure recorders - benefit from the STM32L476RET6's integrated USB 2.0 Full-Speed OTG with on-chip PHY, eliminating an external transceiver and BOM. The 128 KB SRAM buffers high-rate sensor samples (e.g., 1 kHz accelerometer packets) before writes to SPI Flash, while the 12-bit ADC handles slow channels. Standby mode at 1.1 uA keeps the device dormant between log intervals while the RTC schedules a wake-up cycle. ST's documented AES-256 block secures logs from tampering, an increasingly relevant feature for regulated applications (GxP, pharma, cold chain).
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для STM32L476RET6 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | STM32L476RGT6 | STM32L476RCT6 | STM32L476RCT6TR |
|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 64-LQFP (10x10 mm) | 64-LQFP (10x10 mm) - same | 64-LQFP (10x10 mm) - same | 64-LQFP (10x10 mm) - same |
| Flash Memory | 512 KB | 1 MB | 256 KB | 256 KB |
| SRAM | 128 KB | 128 KB | 128 KB | 128 KB |
| Maximum Clock | 80 MHz | 80 MHz | 80 MHz | 80 MHz |
| USB OTG | Yes (FS, on-chip PHY) | Yes (FS, on-chip PHY) | Yes (FS, on-chip PHY) | Yes (FS, on-chip PHY) |
| LCD Controller | Yes (8x40 / 4x44) | Yes (8x40 / 4x44) | Yes (8x40 / 4x44) | Yes (8x40 / 4x44) |
| AES-256 / TRNG | Yes | Yes | Yes | Yes |
| Operating Temperature | -40C to +85C | -40C to +85C (T6 suffix) | -40C to +85C (T6 suffix) | -40C to +85C (T6 suffix) |
Ключевые отличия
- Optimized Flash density tier (512 KB) balances cost and code headroom (против STM32L476RGT6 (1 MB))
- Identical SRAM and clock ceiling as 1 MB cousin, but smaller die footprint (против STM32L476RCT6 (256 KB Flash))
- Same 64-LQFP 'RE' footprint as Flash-density cousins (против STM32L452RET6P (L4 family variant))
Заметки по проектированию
Place one 100 nF X7R decoupling capacitor adjacent to every VDD and VDDA pin, plus a single 4.7 uF bulk on the main power rail within 10 mm of the package. If the internal SMPS is used, add a 4.7 uH low-DCR (e.g., 220 mohm) inductor between VLX and VCORE; remove or solder-bypass the SMPS only if a clean 1.2 V external LDO is provided. Always populate the NRST 10 kohm/100 nF reset network - omitting it causes sporadic power-up failures in noisy environments and on coin-cell ramps.
Keep the LSE 32.768 kHz crystal traces short (under 10 mm) and shield them with a ground guard ring; route HSE traces as a matched pair 50 ohm / 5 mm max. Use separate ground returns for AGND (VSSA) and DGND (VSS), joining them at one point beneath the package to minimize ADC reference drift. For USB OTG, the DP / DM pair requires 90 ohm differential, max length 50 mm, with no stubs. ST's datasheet DM00108832 documents reference layouts for both internal SMPS and external LDO modes.
Estimated: enabling the SMPS without a 4.7 uH inductor can damage the device. Likewise, forcing Stop-mode current measurements below 1.3 uA requires that all GPIOs be configured as analog, Wakeup pins disabled, and RTC using LSE - on-chip pull-ups will otherwise bias the measured current upward. The integrated USB FS PHY requires a 1.5 kohm pull-up on DP; lacking it (or pulling on the wrong pin) prevents enumeration. The datasheet's HSE bypass mode (HSE bypassed) is mandatory if feeding an external clock, to avoid silicon damage during startup.
Информация о соответствии
RoHS and REACH compliant per the ST product page. Halogen-free per ST's L4 datasheet. AEC-Q100 not applicable to this commercial ('T6') grade part; AEC-Q100-qualified automotive parts exist separately in the STM32L4 lineup.
