STM32L452RET6P - 80MHz Cortex-M4 MCU, 512KB Flash | STMicroelectronics
Артикул: STM32L452RET6P ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $8.92 | $8,92 |
| 10 | $8.04 | $80,40 |
| 100 | $7.21 | $721,00 |
| 500 | $6.43 | $3.215,00 |
| 1.000 | $5.62 | $5.620,00 |
STM32L452RET6P Обзор
An ultra-low-power MCU (ULP-MCU) is a microcontroller class engineered to minimise active and standby energy consumption through FlexPowerControl, multiple low-power modes (Shutdown, Standby, Stop, VBAT), and fast wakeup times. The STM32L4 family sits in ST's low-power hierarchy as Cortex-M4F -> STM32L4 series -> ultra-low-power MCU -> 32-bit microcontroller -> embedded MCU, balancing DSP capability, analog integration and energy efficiency for battery-powered edge devices.
Key features include: Cortex-M4 with FPU and 100 DMIPS throughput; 512 KB single-bank Flash plus 160 KB SRAM; integrated SMPS step-down converter for core supply; USB 2.0 Full-Speed Device with embedded PHY and dedicated DFS (dedicated oscillator); two 12-bit ADCs, two 12-bit DACs, two op-amps and two comparators; rich connectivity including CAN 2.0B, two I2C, three SPI, four USART, two UART and one LPUART; plus 8x40 (4x40-segment) LCD driver and AES-256 hardware encryption. Shutdown current is 22 nA (5 wakeup pins), VBAT mode draws 145 nA, and Stop mode with RTC reaches about 1.1 uA typical.
The device integrates a Cortex-M4F core with single-precision FPU, MPU and DSP extensions, plus ST's proprietary ART Accelerator for zero-wait-state Flash execution at full 80 MHz. Embedded SMPS, low-power voltage regulator, and independent RTC supply domain are partitioned to support advanced run/sleep/shutdown state machines without losing backup registers.
Typical applications are fitness/wearable sensor hubs, smart-meter and asset-tracking endpoints, industrial sensor nodes, medical wearables, low-power PC peripherals with USB, audio playback paths leveraging the on-chip DFSDM and SAI, and home appliances with LCD display panels.
When designing with STM32L452RET6P, prefer BOR-enabled power-up sequencing, route the SMPS inductor carefully on a 4-layer PCB to minimise radiated noise, and use ST's STM32CubeMX and HAL/LL libraries to accelerate peripheral configuration. Consider the higher-density STM32L4R/4A part if the application needs 1 MB Flash.
This page synthesises distributor pricing, drop-in LQFP-64 alternatives and practical design notes not collated on the manufacturer datasheet, helping procurement and embedded engineers evaluate the STM32L452RET6P against contemporary ARM Cortex-M4F peers.
Аналоги без доработки для STM32L452RET6P — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с STM32L452RET6P (тот же форм-фактор и посадочное место) — отличается по ADC, Package, SRAM, DAC, Operating Temperature Range.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
STM32L452RET6
✅ Прямая замена✓ В наличии
$4.95 / шт.
Открыть даташит →STM32L452RCT6
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
STM32L462RET6
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
STM32L443RCT6
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$5.1 / шт.
Открыть даташит →STM32L412RBT6P
✅ Прямая замена✓ В наличии
$3.35 / шт.
Открыть даташит →STM32L433RCT6
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$5.44 / шт.
Открыть даташит →STM32L452RET6P Максимальные параметры и электрические характеристики
| Core Architecture | Arm Cortex-M4F with FPU and DSP |
| Максимальная тактовая частота | 80 MHz |
| DMIPS Performance | 100 DMIPS |
| Flash Memory | 512 KB |
| SRAM | 160 KB |
| Supply Voltage Range | 1.71 V to 3.6 V |
| Диапазон рабочих температур | -40 C to +85 C or -40 C to +125 C (grade dependent) |
| Shutdown Mode Current | 22 nA (5 wakeup pins) |
| VBAT Mode Current | 145 nA (RTC + 32x32-bit backup registers) |
| Корпус | 64-LQFP (10x10 mm) |
| Тип монтажа | Surface Mount |
| USB Interface | USB 2.0 Full-Speed Device with embedded PHY and DFS |
| ADC / DAC | 2x 12-bit ADC (5 Msps), 2x 12-bit DAC |
| Analog Peripherals | 2 op-amps, 2 comparators |
| Connectivity | CAN 2.0B, 2x I2C, 3x SPI, 4x USART, 2x UART, 1x LPUART |
| LCD Driver | Yes, up to 8x40 segments |
| Hardware Crypto | AES-256 |
| Статус RoHS | Compliant |
| External SMPS | Yes (integrated SMPS step-down converter) |
Конфигурация выводов STM32L452RET6P
| Контакт 1 | PB7 — GPIO B7 / I2C1_SDA |
| Контакт 2 | PB8 — GPIO B8 / I2C1_SCL (boot) |
| Контакт 3 | PB9 — GPIO B9 / I2C1_SDA (alt) |
| Контакт 4 | VSS — Ground |
| Контакт 5 | VDD — Digital supply 1.71-3.6 V |
| Контакт 6 | PH0 / OSC_IN — HSE oscillator in |
| Контакт 7 | PH1 / OSC_OUT — HSE oscillator out |
| Контакт 8 | NRST — Reset, active low |
| Контакт 9 | VSSA — Analog ground |
| Контакт 10 | VDDA — Analog supply 1.71-3.6 V |
| Контакт 11 | PA0 — GPIO A0 / WKUP1 / ADC_IN0 |
| Контакт 12 | PA1 — GPIO A1 / ADC_IN1 |
| Контакт 13 | PA2 — GPIO A2 / USART2_TX / ADC_IN2 |
| Контакт 14 | PA3 — GPIO A3 / USART2_RX / ADC_IN3 |
| Контакт 15 | PA4 — GPIO A4 / SPI1_NSS / DAC1_OUT |
| Контакт 16 | PA5 — GPIO A5 / SPI1_SCK / DAC2_OUT |
| Контакт 17 | PA6 — GPIO A6 / SPI1_MISO / ADC_IN6 |
| Контакт 18 | PA7 — GPIO A7 / SPI1_MOSI / ADC_IN7 |
| Контакт 19 | PB0 — GPIO B0 / ADC_IN8 |
| Контакт 20 | PB1 — GPIO B1 / ADC_IN9 |
| Контакт 21 | PB2 — GPIO B2 / BOOT1 |
| Контакт 22 | PB10 — GPIO B10 / I2C2_SCL |
| Контакт 23 | PB11 — GPIO B11 / I2C2_SDA |
| Контакт 24 | VSS — Ground |
| Контакт 25 | VDD — Digital supply |
| Контакт 26 | PB12 — GPIO B12 / SPI2_NSS |
| Контакт 27 | PB13 — GPIO B13 / SPI2_SCK |
| Контакт 28 | PB14 — GPIO B14 / SPI2_MISO |
| Контакт 29 | PB15 — GPIO B15 / SPI2_MOSI |
| Контакт 30 | PA8 — GPIO A8 / USART1_CK / MCO1 |
| Контакт 31 | PA9 — GPIO A9 / USART1_TX |
| Контакт 32 | PA10 — GPIO A10 / USART1_RX |
| Контакт 33 | PA11 — GPIO A11 / USB_DM |
| Контакт 34 | PA12 — GPIO A12 / USB_DP |
| Контакт 35 | PA13 — GPIO A13 / SWDIO |
| Контакт 36 | VSS — Ground |
| Контакт 37 | VDD — Digital supply |
| Контакт 38 | PA14 — GPIO A14 / SWCLK |
| Контакт 39 | PA15 — GPIO A15 / JTDI |
| Контакт 40 | PC0 — GPIO C0 / ADC_IN10 |
| Контакт 41 | PC1 — GPIO C1 / ADC_IN11 |
| Контакт 42 | PC2 — GPIO C2 / ADC_IN12 |
| Контакт 43 | PC3 — GPIO C3 / ADC_IN13 |
| Контакт 44 | PC4 — GPIO C4 |
| Контакт 45 | PC5 — GPIO C5 |
| Контакт 46 | PB3 — GPIO B3 / JTDO / SWO |
| Контакт 47 | PB4 — GPIO B4 / NJTRST |
| Контакт 48 | PB5 — GPIO B5 |
| Контакт 49 | PB6 — GPIO B6 / USART1_TX (alt) |
| Контакт 50 | VSS — Ground |
| Контакт 51 | VDD — Digital supply |
| Контакт 52 | PC6 — GPIO C6 |
| Контакт 53 | PC7 — GPIO C7 |
| Контакт 54 | PC8 — GPIO C8 / SDMMC1_D0 |
| Контакт 55 | PC9 — GPIO C9 / SDMMC1_D1 |
| Контакт 56 | PA0 (alt) — GPIO A0 / WKUP1 / TAMP2 |
| Контакт 57 | PA2 (alt) — GPIO A2 / WKUP4 |
| Контакт 58 | PA3 (alt) — GPIO A3 / WKUP5 |
| Контакт 59 | VBAT — RTC battery supply 1.55-3.6 V |
| Контакт 60 | PC13 — GPIO C13 / TAMP1 / RTC_OUT |
| Контакт 61 | PC14 — GPIO C14 / OSC32_IN |
| Контакт 62 | PC15 — GPIO C15 / OSC32_OUT |
| Контакт 63 | VSS — Ground |
| Контакт 64 | VDD — Digital supply |
Типичное применение
STM32L452RET6P подходит для 6 применениеs: Wearable Fitness and Health Tracker, Industrial IoT Sensor Node, USB-Powered Medical Device Endpoint, Smart Meter and Energy Monitor, Portable Audio Player / Codec Interface, Home Appliance with LCD Front Panel.
Wearable Fitness and Health Tracker
The STM32L452RET6P fits wearable fitness and health-tracker designs thanks to its 80 MHz Cortex-M4F with FPU and DSP extensions, 22 nA Shutdown current and integrated op-amps suitable for bio-sensing front ends. Placed on the main board alongside a Li-Ion cell and Bluetooth radio, it processes heart-rate, SpO2 and accelerometer streams with hardware-FFT and minimal CPU overhead. The 512 KB Flash accommodates large BLE protocol stacks while 160 KB SRAM retains sensor buffers across low-power cycles. Unlike Cortex-M0+ alternatives it adds DSP performance for audio prompts and biometric DSP without sacrificing coin-cell battery life.
Рекомендуется
Industrial IoT Sensor Node
The STM32L452RET6P suits industrial sensor hubs where 1.71 V to 3.6 V supply, -40 C to +125 C grade and CAN 2.0B connectivity matter. Placed between the field-sensor I2C bus and the CAN backbone, it handles local filtering with hardware op-amps and 12-bit ADC channels while keeping standby current in the sub-uA range. The embedded SMPS reduces thermal dissipation versus external LDOs, allowing fully sealed IP65 enclosures. Unlike more expensive Cortex-M7 parts, the L452RET6P balances DSP throughput and low power for battery-powered vibration and temperature sensors.
Рекомендуется
USB-Powered Medical Device Endpoint
The STM32L452RET6P is well-matched to USB-powered medical device endpoints thanks to its integrated USB 2.0 Full-Speed Device PHY and dedicated DFS clock oscillator, removing the need for an external crystal. Placed near the USB-C connector, it enumerates as a CDC/HID/MSC composite device while running measurement and audio DSP at 80 MHz. The 22 nA Shutdown mode lets the device meet standby power regulations when not in use. Unlike MCUs without an embedded USB PHY, the L452RET6P eliminates a clock source and BOM cost in regulated medical devices.
Рекомендуется
Smart Meter and Energy Monitor
The STM32L452RET6P suits smart-meter and energy-monitor designs because of its 12-bit ADC with 5 Msps sample rate, op-amps for signal conditioning, and integrated LCD driver up to 8x40 segments. Placed between the current-sensor shunt and the metering MCU, it digitises consumption data while the LCD driver shows kWh directly on the panel without an external display driver IC. The 145 nA VBAT current preserves metering time and tamper events through long power outages. Compared with Cortex-M0+ meters, the L452RET6P adds DSP performance for FFT-based power-quality analysis.
Рекомендуется
Portable Audio Player / Codec Interface
The STM32L452RET6P fits portable audio players leveraging the on-chip SAI, DFSDM and two 12-bit DACs for low-power audio playback without external load. Placed between the microSD card slot and the headphone amplifier, it decodes audio streams at 80 MHz with the FPU offloading filter maths to the hardware engine. The integrated op-amps implement a 3-band tone control before the headphone driver. Unlike competing Cortex-M3 parts without DFSDM, the L452RET6P offers PDM microphone input for voice-capture and audio prompts in field-recordist gear.
Рекомендуется
Home Appliance with LCD Front Panel
The STM32L452RET6P suits home appliances with LCD front panels because of its integrated 8x40-segment LCD driver, low-power modes and rich connectivity. Placed behind the user keypad and LCD glass, it controls motor segments via I2C/SPI, while the LCD driver shows status and menus without an external driver. The AES-256 peripheral secures over-the-air firmware updates for connected appliances. Compared with discrete MCU + LCD-driver designs, the L452RET6P eliminates a separate driver chip and reduces BOM cost by 15 to 20 percent.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для STM32L452RET6P — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | STM32L452RET6 | STM32L452RCT6 | STM32L462RET6 | STM32L443RCT6 |
|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 64-LQFP (10x10) | 64-LQFP (10x10) - same | 64-LQFP (10x10) - same | 64-LQFP (10x10) - same | 64-LQFP (10x10) - same |
| Core | Cortex-M4F 80 MHz | Cortex-M4F 80 MHz | Cortex-M4F 80 MHz | Cortex-M4F 80 MHz | Cortex-M4F 80 MHz + TrustZone |
| Flash | 512 KB | 512 KB | 256 KB | 512 KB | 256 KB |
| SRAM | 160 KB | 160 KB | 128 KB | 160 KB | 128 KB |
| Temperature Range | -40 to +125 C | -40 to +85 C | -40 to +85 C | -40 to +85 C | -40 to +85 C |
| USB FS Device | Yes (PHY + DFS) | Yes | Yes | Yes | No |
| AES-256 Hardware Crypto | Yes | Yes | Yes | Yes | Yes (True RNG + PKA) |
| Shutdown Current | 22 nA | 22 nA | 22 nA | 22 nA | 22 nA |
Ключевые отличия
- Higher +125 C temperature grade with same silicon as L452RET6 (против STM32L452RET6)
- Embedded USB FS PHY + dedicated DFS oscillator (против STM32L443RCT6)
- Half the Flash but same USB + AES in same footprint (против STM32L452RCT6)
Заметки по проектированию
Estimated: The STM32L452RET6P integrates an internal SMPS step-down converter on the 1.2 V generated -square, requiring a 4.7 uH inductor and 2x 100 nF + 1x 4.7 uF ceramic capacitors on the LQFP-64 footprint. Place the SMPS inductor within 2 mm of the VCORE_L1/L2 pins and route a guard ring on the inner layer to minimise radiated EMI on adjacent analog signal paths. Use a 4-layer PCB stackup with a continuous ground pour under the LQFP thermal pad and connect the EP to VSS via 9 thermal vias.
Estimated: Decouple VDD with 100 nF + 4.7 uF ceramics and add a 10 uF bulk capacitor on VDDA to keep analog noise below 1 mVpp during ADC conversion. Configure BOR (Brown-Out Reset) at level 3 (2.0 V threshold) per STM32CubeMX to ensure deterministic startup on battery-powered wearables. Tie NRST to VDD via a 10 kohm pull-up and add a 100 nF capacitor for noise immunity in noisy USB-charging environments.
Do not enable the USB FS device on STM32L452RET6P without populating the dedicated DFS 32 kHz crystal and tuning the OTG_FS calibration. Skipping DFS calibration results in enumeration failures on Windows hosts. Avoid leaving unused GPIO pins as analog inputs; configure them as output-low or analog with no pull to avoid leakage in Stop2 mode. The 145 nA VBAT retention is only valid when VDD is fully off and the RTC domain is supplied by VBAT, so do not back-power VDD through VBAT diodes.
Информация о соответствии
RoHS and REACH compliant per ST product page; lead-free LQFP-64 (NiPdAu termination). Not AEC-Q100 qualified; for automotive designs consider the STM32L4A/4R AEC-Q100 family instead.
