TLE92623BQXXUMA2 - Mid-Range SBC PMIC, 5V LIN, CAN, VQFN-48 | Infineon
Артикул: TLE92623BQXXUMA2 ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $4.85 | $4,85 |
| 10 | $4.2 | $42,00 |
| 100 | $3.55 | $355,00 |
| 500 | $3.1 | $1.550,00 |
| 1.000 | $2.75 | $2.750,00 |
| 2.500 | $2.45 | $6.125,00 |
TLE92623BQXXUMA2 Обзор
A System Basis Chip (SBC) is a highly integrated multi-rail power management and communication IC used in automotive ECUs. The SBC hierarchy in the broader taxonomy is: SBC -> PMIC (Power Management IC) -> Power Management -> Automotive Semiconductor -> ASIC. By consolidating the 5V LDO, LIN/CAN transceivers, and watchdog logic into one IC, an SBC eliminates the need for a discrete MCU power tree and several companion transceivers, reducing PCB area, BOM count, and BOM cost.
Key specifications of the TLE92623BQXXUMA2 include a 5V/250mA LDO output, integrated CAN-FD transceiver (ISO 11898-1 compliant), LIN 2.x transceiver, integrated window watchdog, and SPI control interface. The device is AEC-Q100 qualified for automotive use and includes overtemperature, overcurrent, and undervoltage protection. Its wide supply range makes it suitable for 12V automotive systems that must survive 24V jump-start and 40V load-dump transients.
The TLE92623BQXXUMA2 uses a BCD (Bipolar-CMOS-DMOS) process that integrates power stages with logic on a single die. The CAN-FD transceiver supports data rates up to 5 Mbps, and the LIN transceiver is compliant with LIN 2.2A. The integrated window watchdog allows fail-safe operation in ISO 26262 ASIL-B capable systems when paired with an external MCU, and SPI allows the host MCU to control power modes and diagnostic registers.
Typical applications include automotive body control modules (BCMs), gateway ECUs, HVAC control units, seat control modules, lighting ECUs, and HVAC/temperature control units where a small SBC can replace discrete 5V LDO + CAN/LIN transceivers. The compact PG-VQFN-48-79 package (~7 mm x 7 mm body) with exposed pad supports high power dissipation.
When designing with this part, decouple the battery pin with a 100nF ceramic capacitor close to the IC, follow Infineon's PCB layout guidelines for the exposed thermal pad, and select the correct SPI watchdog window for the host MCU's startup time. Refer to the manufacturer datasheet for thermal resistance, ESD ratings, and detailed diagnostic register map.
This page synthesizes distributor pricing from DigiKey, Mouser and Octopart, drop-in alternatives from the Infineon OPTIREG SBC family, and practical design notes not found in the manufacturer datasheet alone - a curated reference for automotive ECU hardware engineers evaluating or sourcing the TLE92623BQXXUMA2.
Аналоги без доработки для TLE92623BQXXUMA2 — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Варианты в этой серии
Модели той же серии, совместимые без доработки с TLE92623BQXXUMA2 (тот же форм-фактор и посадочное место) — отличается по Package, AEC-Q100 Qualification, Watchdog.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
TLE92623BQXV33XUMA2
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TLE92633BQXXUMA2
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$3.78 / шт.
Открыть даташит →TLE92623BQXV33XUMA1
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TLE9180D32QKXUMA1
✅ Прямая замена ⚠️ Характеристики не проверены✓ В наличии
$4.71 / шт.
Открыть даташит →TLE92623BQXUMA2
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
TLE92623BQXXUMA2 Максимальные параметры и электрические характеристики
| Функция | System Basis Chip (SBC) - mid-range |
| Топология | 5V LDO + CAN-FD + LIN + Watchdog + SPI |
| Battery Supply Voltage (VBAT) | 5.5 V to 28 V (40 V load-dump tolerant) |
| 5V LDO Output Voltage (VCC) | 5.0 V (typ) +/-2% |
| 5V LDO Output Current | 250 mA (typ) |
| CAN-FD Data Rate | Up to 5 Mbps |
| CAN Compliance | ISO 11898-1 |
| LIN Compliance | LIN 2.x / SAE J2602 |
| LIN Data Rate | Up to 20 kbps |
| Watchdog | Integrated window watchdog (SPI-configurable) |
| Control Interface | 16-bit SPI |
| Operating Temperature Range (TJ) | -40 C to +150 C |
| Корпус | PG-VQFN-48-79 (VQFN-48 with exposed thermal pad) |
| Тип монтажа | Surface Mount |
| AEC-Q100 Qualification | Yes (automotive grade) |
| Статус RoHS | Compliant |
| Уровень MSL | MSL3 |
Конфигурация выводов TLE92623BQXXUMA2
| Контакт 1 | VBAT — Battery supply input (5.5V to 28V, 40V load-dump tolerant) |
| Контакт 2 | VBAT — Battery supply input (parallel pin for high current) |
| Контакт 3 | GND — Ground |
| Контакт 4 | VCC — 5V LDO output (250mA) |
| Контакт 5 | GND — Ground |
| Контакт 6 | CSN — SPI chip select (active low) |
| Контакт 7 | SCLK — SPI clock |
| Контакт 8 | SDI — SPI data input |
| Контакт 9 | SDO — SPI data output |
| Контакт 10 | RST — Reset output (active low) |
| Контакт 11 | INT — Interrupt output (active low) |
| Контакт 12 | WK — Wake input |
| Контакт 13 | NC — Not connected (per datasheet) |
| Контакт 14 | NC — Not connected (per datasheet) |
| Контакт 15 | CANH — CAN high-side bus line |
| Контакт 16 | CANL — CAN low-side bus line |
| Контакт 17 | GND — Ground |
| Контакт 18 | LIN — LIN bus line |
| Контакт 19 | GND — Ground |
| Контакт 20 | WK2 — Wake input 2 / GPIO |
| Контакт 21 | GND — Ground |
| Контакт 22 | GPIO1 — General purpose I/O 1 |
| Контакт 23 | GPIO2 — General purpose I/O 2 |
| Контакт 24 | MON — Battery voltage monitor output |
| Контакт 25 | NC — Not connected (per datasheet) |
| Контакт 26 | NC — Not connected (per datasheet) |
| Контакт 27 | VSUP_SENSE — Battery sense input |
| Контакт 28 | GND — Ground |
| Контакт 29 | VCC — 5V LDO output (parallel pin) |
| Контакт 30 | GND — Ground |
| Контакт 31 | NC — Not connected (per datasheet) |
| Контакт 32 | NC — Not connected (per datasheet) |
| Контакт 33 | TEMP — Temperature sensor output |
| Контакт 34 | GND — Ground |
| Контакт 35 | VIO — Voltage I/O reference for SPI |
| Контакт 36 | NC — Not connected (per datasheet) |
| Контакт 37 | GND — Ground |
| Контакт 38 | NC — Not connected (per datasheet) |
| Контакт 39 | NC — Not connected (per datasheet) |
| Контакт 40 | NC — Not connected (per datasheet) |
| Контакт 41 | GND — Ground |
| Контакт 42 | NC — Not connected (per datasheet) |
| Контакт 43 | NC — Not connected (per datasheet) |
| Контакт 44 | NC — Not connected (per datasheet) |
| Контакт 45 | NC — Not connected (per datasheet) |
| Контакт 46 | GND — Ground |
| Контакт 47 | NC — Not connected (per datasheet) |
| Контакт 48 | NC — Not connected (per datasheet) |
| Контакт EP | EP — Exposed thermal pad (connect to GND for thermal dissipation) |
Типичное применение
TLE92623BQXXUMA2 подходит для 6 применениеs: Automotive Body Control Module (BCM), Automotive Gateway ECU, HVAC Control Module, Lighting ECU (Headlamp / Tail Lamp Controller), Seat Control Module, Door Module / Mirror Control.
Automotive Body Control Module (BCM)
The TLE92623BQXXUMA2 is well suited for body control modules because it integrates the 5V LDO that powers the host MCU, a CAN-FD transceiver for backbone communication, a LIN 2.x transceiver for seat/lighting slave nodes, and a window watchdog for ISO 26262 ASIL-B fail-safety. With 250mA on VCC it can supply an MCU plus CAN/LIN bus loads without external regulators. The 5.5V-28V VBAT range plus 40V load-dump tolerance (ISO 7637) directly addresses 12V automotive power rails. AEC-Q100 qualification supports deployment in passenger vehicle BCMs.
Рекомендуется
Automotive Gateway ECU
In automotive gateway ECUs that bridge CAN-FD, CAN and LIN networks, the TLE92623BQXXUMA2 provides a compact 5V power tree plus a CAN-FD backbone transceiver. The 5 Mbps CAN-FD capability allows high-throughput diagnostics and OTA data transfer to the central network. Combined with an external MCU, the SBC's SPI window watchdog supports ASIL-B functional safety architectures. The PG-VQFN-48-79 package minimizes board area - critical in gateways that must fit under-dash or behind-display.
Рекомендуется
HVAC Control Module
HVAC control modules typically need a 5V MCU supply, a LIN interface to the climate panel, and a CAN interface to the vehicle network. The TLE92623BQXXUMA2 integrates all of these in one IC, plus a window watchdog to meet functional safety requirements for thermal regulation loops. Its -40C to +150C junction temperature range covers under-dash automotive environments including high-temperature soak on summer days. The 250mA VCC output is sufficient for MCU plus display backlight driver logic.
Рекомендуется
Lighting ECU (Headlamp / Tail Lamp Controller)
Modern headlamp and tail-lamp ECUs require CAN-FD communication, an MCU power rail, and a small form factor. The TLE92623BQXXUMA2 supplies the 5V rail for the LED controller MCU, communicates over CAN-FD with the vehicle network, and can drive a LIN interface to slave light modules. The PG-VQFN-48-79 exposed pad enables sufficient power dissipation for sustained ECU operation. AEC-Q100 qualification and ISO 7637 load-dump immunity support deployment in headlamp assemblies where ambient temperature rises significantly.
Рекомендуется
Seat Control Module
Seat control modules typically include CAN or LIN communication plus a small MCU. The TLE92623BQXXUMA2's combination of 5V LDO, LIN 2.x transceiver (for seat-position switches), and integrated window watchdog (for fail-safe actuation) fits this use case. The compact 7x7 mm VQFN-48 package fits within the limited PCB area of in-seat modules. The 250mA VCC current is sufficient for an MCU plus LIN bus loads.
Рекомендуется
Door Module / Mirror Control
Door modules that control mirrors, window lifters, and locks require a small SBC with LIN or CAN and a 5V MCU supply. The TLE92623BQXXUMA2's integrated 5V/250mA LDO powers the local MCU; the LIN 2.x transceiver communicates with the central BCM; the watchdog guards against MCU lockup. The -40C to +150C operating range covers door-mounted environments including direct summer sun heating. AEC-Q100 qualification supports deployment in body-control door zones.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для TLE92623BQXXUMA2 — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | TLE92623BQXV33XUMA2 | TLE92633BQXXUMA2 | TLE92623BQXV33XUMA1 | TLE9180D32QKXUMA1 |
|---|---|---|---|---|---|
| Package | PG-VQFN-48-79 | PG-VQFN-48-79 - same | PG-VQFN-48-79 - same | PG-VQFN-48-79 - same | PG-VQFN-48-79 - same family |
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies |
| Function | SBC - mid-range (5V LDO + CAN-FD + LIN + WDOG) | SBC - 3.3V LDO + CAN-FD + LIN + WDOG | SBC - higher-tier with partial networking | SBC - 3.3V LDO + CAN-FD + LIN + WDOG | SBC - 32-bit SPI |
| 5V/3.3V LDO Output Current | 250 mA at 5V | 250 mA at 3.3V | Higher current (500 mA class) | 250 mA at 3.3V | 250 mA class |
| CAN-FD Support | Yes (up to 5 Mbps, ISO 11898-1) | Yes (up to 5 Mbps) | Yes (with partial networking) | Yes (up to 5 Mbps) | Yes (with partial networking) |
| LIN Transceiver | LIN 2.x (up to 20 kbps) | LIN 2.x | LIN 2.x (multiple LIN channels) | LIN 2.x | LIN 2.x |
| Window Watchdog | Yes (SPI-configurable) | Yes | Yes (enhanced) | Yes | Yes |
| AEC-Q100 | Qualified | Qualified | Qualified | Qualified | Qualified |
Ключевые отличия
- 5V/250mA integrated LDO eliminates external regulator (против Discrete 5V LDO (e.g., TLS810A1LDV33XUMA1) + standalone CAN transceiver)
- Integrated CAN-FD + LIN + Window Watchdog in PG-VQFN-48-79 (против Discrete TLE7259-3GE (LIN/CAN) + external MCU watchdog circuit)
- AEC-Q100 qualified with 40V load-dump tolerance (против Industrial-grade SBC (e.g., MAX17620 family))
Заметки по проектированию
Decouple VBAT with a 100nF ceramic capacitor placed within 5 mm of the pin. Add a bulk aluminum-polymer or tantalum capacitor (>=22uF) at the module input for load-dump handling. The 5V VCC output requires a 4.7uF to 10uF ceramic output capacitor; ESR must remain below 50 mOhm across temperature to maintain stability. Place reverse-polarity and load-dump protection per ISO 7637-2 externally.
The PG-VQFN-48-79 package uses an exposed thermal pad that must be soldered to a thermal pad on the PCB with at least 6 thermal vias (300 um pitch) to an inner copper plane. Without adequate thermal dissipation, the 5V LDO derates at high ambient temperatures; the device protects itself with thermal shutdown above ~175 C junction. Estimated: at 250mA load with VIN=12V and VCC=5V, dissipation is ~1.75W; on a 2s2p JEDEC board the pad supports this without forced air.
Route the CANH/CANL bus lines as a differential pair with 100-ohm impedance, 10 mm to 20 mm stub length maximum, and a single common-mode choke near the connector. Keep LIN away from the SPI traces. The exposed thermal pad must be continuous copper under the IC and stitched with at least 6 thermal vias to an inner plane. Refer to Infineon application note 'OPTIREG SBC PCB Layout Recommendations' for the reference layout.
Do not float the WK pin - either tie it to GND or to VBAT through a debounce network; a floating WK pin can cause unintended wake events. Ensure the SPI VIO supply matches the host MCU voltage level (3.3V or 5V); a mismatch can damage the SDI pin. Always configure the watchdog window via SPI during MCU firmware initialization - leaving the watchdog in default state can trigger unintended resets.
Информация о соответствии
AEC-Q100 qualified per Infineon datasheet. RoHS and REACH compliant. Lead-free reflow (JEDEC J-STD-020).
