TLV2765IN - Quad 3.6V 500kHz RRIO Op Amp | Texas Instruments
Артикул: TLV2765IN ✓ АктивенTLV2765IN Обзор
An operational amplifier is a voltage-gain building block used to amplify, buffer, filter, compare, and control analog signals. The TLV2765 belongs to the operational-amplifier hierarchy, where rail-to-rail input and output operation helps the amplifier process signals near the positive and negative supply rails. The TLV2765 family combines this signal-handling capability with low quiescent current and shutdown control for portable and low-power systems.
Key features include four amplifier channels, CMOS-compatible rail-to-rail inputs, rail-to-rail outputs, a 500kHz gain-bandwidth product, and operation from 1.8V to 3.6V. The approximately 20uA per-channel supply current supports battery-powered equipment where every microampere affects useful runtime. A common shutdown pin can disable all four channels, while the 10nA per-channel shutdown current limits backup and standby consumption.
The wide common-mode input range makes the TLV2765 useful when signals approach either supply rail. Its 500kHz bandwidth supports low-frequency signal conditioning, sensor interfaces, filtering, and general instrumentation rather than high-speed video or RF amplification. The 3.6V maximum recommended supply also permits operation from two AA or AAA cells, although designers should account for cell-voltage variation and confirm the required headroom.
Typical applications include portable measurement systems, low-voltage sensor interfaces, battery-powered instrumentation, analog signal conditioning, and industrial control modules. Shutdown is particularly useful when a system must periodically enter a low-power state without completely losing its supply. In multi-amplifier designs, the common shutdown control can simplify state management across all four channels.
Designers should verify output current, output swing, input bias behavior, and stability against the specific load and signal amplitude. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be biased to a defined common-mode voltage to prevent unstable operation.
This page combines the manufacturer device information, package characteristics, application guidance, parameter comparisons, and practical design notes to support component selection and PCB implementation for the TLV2765IN quad rail-to-rail operational amplifier.
Аналоги без доработки для TLV2765IN — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
TLV2765IP
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
TLV2765IN Максимальные параметры и электрические характеристики
| Number of Channels | 4 circuits |
| Minimum Supply Voltage | 1.8 V |
| Maximum Recommended Supply Voltage | 3.6 V |
| Gain-Bandwidth Product | 500 kHz |
| Quiescent Current per Channel | 20 uA |
| Shutdown Current per Channel | 10 nA |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Shutdown Control | Common shutdown function |
| Temperature Grade | Industrial |
| Terminal Form | Through-hole |
| Number of Terminals | 14 terminals |
| Корпус | 14-pin rectangular DIP |
| Technology | CMOS |
| Amplifier Type | Single supply, rail-to-rail input/output operational amplifier |
Руководство по цоколевке TLV2765IN в корпусе 14-pin rectangular dip
Цоколевка для TLV2765IN (корпус 14-pin rectangular dip). Этот аналоговый компонент имеет выводы входа, выхода и питания. Обратитесь к техническому описанию производителя для конфигураций выводов балансировки нуля, коррекции и разрешения. Идеально подходит для схем обработки сигналов и усилителей.
Нет подробных данных о распиновке для TLV2765IN.
Обратитесь к даташиту для полной конфигурации выводов.
Типичное применение
TLV2765IN подходит для 6 применениеs: Portable Sensor Signal Conditioning, Battery-Powered Instrumentation, Industrial Process Measurement, Low-Voltage Active Filtering, Precision Voltage Buffering, Standby and Monitoring Circuitry.
Portable Sensor Signal Conditioning
The TLV2765IN fits low-voltage sensor interfaces where four channels must operate from a 1.8V supply with limited battery capacity. Its approximately 20uA per-channel current and rail-to-rail input behavior help preserve signal range in compact systems. Place the amplifier close to the sensor and conditioning network, then validate the sensor output against the amplifier input range. Shutdown can reduce standby demand to 10nA per channel when the sensing subsystem is not being sampled.
Рекомендуется
Battery-Powered Instrumentation
The TLV2765IN is useful in handheld or field instrumentation operating from two AA or AAA cells. The 1.8V minimum supply, 500kHz gain-bandwidth product, and approximately 20uA per-channel consumption support analog measurement channels without requiring a high-voltage supply. The common shutdown control allows the instrument to enter a low-power state between readings. Confirm cell-regulation limits, sensor excitation requirements, and the complete analog signal path before finalizing the power architecture.
Рекомендуется
Industrial Process Measurement
The TLV2765IN supports four-channel analog conditioning in industrial process-measurement equipment when the signal and supply levels fall within its low-voltage range. Rail-to-rail inputs can accommodate sensor outputs near the supply rails, while 500kHz bandwidth is sufficient for many slow process signals and filters. The industrial temperature-grade ordering option suits extended ambient environments. Validation should include input common-mode behavior, output swing, noise, settling time, and isolation from adjacent switching circuitry.
Рекомендуется
Low-Voltage Active Filtering
The TLV2765IN can implement active low-pass, high-pass, and filtering stages in low-voltage measurement systems. Its 500kHz gain-bandwidth product provides useful closed-loop bandwidth for sensor noise reduction and signal conditioning at moderate frequencies. Four channels reduce component count when several filter sections are required. Keep input and feedback networks close to the relevant amplifier pins, check capacitor types for the intended signal bandwidth, and use the manufacturer stability guidance when driving capacitive loads.
Рекомендуется
Precision Voltage Buffering
The TLV2765IN can buffer low-voltage sensor and divider outputs where rail-to-rail operation helps preserve signal amplitude. A voltage follower configuration uses the amplifier's high open-loop gain to reduce output loading while maintaining a 1.8V-to-3.6V operating range. The approximately 20uA per-channel supply current is useful in power-constrained designs. Verify offset, input bias current, output-current capability, and settling behavior against the source impedance and required settling time.
Рекомендуется
Standby and Monitoring Circuitry
The TLV2765IN fits systems that need active analog monitoring during normal operation and very low standby consumption afterward. A common shutdown pin controls all four channels, and shutdown current is approximately 10nA per channel according to the Texas Instruments family documentation. This makes the amplifier useful in periodically sampled sensing systems, threshold monitors, and low-duty-cycle test equipment. Validate shutdown polarity and startup behavior in the system state machine rather than assuming the amplifier is immediately ready after shutdown release.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для TLV2765IN — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | TLV2765IP |
|---|---|---|
| Package | DIP-14 | DIP-14 - same |
| Brand | Texas Instruments | Texas Instruments |
| Number of Channels | 4 circuits | 4 circuits |
| Supply Voltage Range | 1.8V to 3.6V | 1.8V to 3.6V |
| Gain-Bandwidth Product | 500kHz | 500kHz |
| Quiescent Current per Channel | 20uA | 20uA |
| Shutdown Current per Channel | 10nA | 10nA |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail |
| Output Swing | Rail-to-rail | Rail-to-rail |
| Shutdown Control | Common shutdown function | Common shutdown function |
Ключевые отличия
- Combines four channels with a common shutdown control (против TLV2765IP)
- Low-voltage operation with rail-to-rail signal handling (против TLV2765IP)
- Through-hole package supports repairable and conventionally assembled boards (против TLV2765IPW)
Заметки по проектированию
Place the supply bypass capacitor and any additional decoupling directly between the supply pins and ground, with the shortest practical return path. Keep amplifier inputs, feedback components, and grounding close to the relevant channel to minimize noise pickup. Because the TLV2765IN is a through-hole DIP, preserve adequate spacing around the package for insertion, soldering, and inspection while keeping sensitive analog traces away from switching-node and high-current return paths.
Do not exceed the 3.6V maximum recommended supply voltage. The approximately 20uA per-channel operating current is suitable for low-power operation, but total supply demand also includes load current, input bias current, and external circuitry. Use the shutdown function for systems that spend significant time inactive, verify its polarity, and account for the time required for the amplifier to become signal-valid after shutdown is released.
Do not leave an unused amplifier input floating. Bias unused non-inverting inputs to a stable common-mode voltage within the input range, or use the manufacturer's recommended unused-channel configuration. Also verify that the intended output voltage remains inside the usable output swing; rail-to-rail inputs do not guarantee ideal rail-to-rail output behavior under every load, output-current, and temperature condition.
The 500kHz gain-bandwidth product makes the TLV2765IN appropriate for low-frequency sensor conditioning, buffering, and moderate-bandwidth filtering rather than high-speed waveform work. Select closed-loop gain and feedback components with the amplifier's frequency and stability characteristics in mind. If driving a capacitive load, add the isolation resistance specified in the manufacturer guidance and verify settling at the required signal bandwidth.
Информация о соответствии
The component is an industrial-temperature-grade operational amplifier; detailed environmental and substance-compliance classifications were not stated on the manufacturer product-page excerpts. AEC-Q100 is marked not applicable because this ordering option is not identified as an automotive-qualified variant.