TLV2765IN - Quad 3.6V 500kHz RRIO Op Amp | Texas Instruments
N.º de pieza: TLV2765IN ✓ ActivoTLV2765IN Descripción general
An operational amplifier is a voltage-gain building block used to amplify, buffer, filter, compare, and control analog signals. The TLV2765 belongs to the operational-amplifier hierarchy, where rail-to-rail input and output operation helps the amplifier process signals near the positive and negative supply rails. The TLV2765 family combines this signal-handling capability with low quiescent current and shutdown control for portable and low-power systems.
Key features include four amplifier channels, CMOS-compatible rail-to-rail inputs, rail-to-rail outputs, a 500kHz gain-bandwidth product, and operation from 1.8V to 3.6V. The approximately 20uA per-channel supply current supports battery-powered equipment where every microampere affects useful runtime. A common shutdown pin can disable all four channels, while the 10nA per-channel shutdown current limits backup and standby consumption.
The wide common-mode input range makes the TLV2765 useful when signals approach either supply rail. Its 500kHz bandwidth supports low-frequency signal conditioning, sensor interfaces, filtering, and general instrumentation rather than high-speed video or RF amplification. The 3.6V maximum recommended supply also permits operation from two AA or AAA cells, although designers should account for cell-voltage variation and confirm the required headroom.
Typical applications include portable measurement systems, low-voltage sensor interfaces, battery-powered instrumentation, analog signal conditioning, and industrial control modules. Shutdown is particularly useful when a system must periodically enter a low-power state without completely losing its supply. In multi-amplifier designs, the common shutdown control can simplify state management across all four channels.
Designers should verify output current, output swing, input bias behavior, and stability against the specific load and signal amplitude. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be biased to a defined common-mode voltage to prevent unstable operation.
This page combines the manufacturer device information, package characteristics, application guidance, parameter comparisons, and practical design notes to support component selection and PCB implementation for the TLV2765IN quad rail-to-rail operational amplifier.
Alternativas directas para TLV2765IN — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
TLV2765IP
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
TLV2765IN Valores máximos y características eléctricas
| Number of Channels | 4 circuits |
| Minimum Supply Voltage | 1.8 V |
| Maximum Recommended Supply Voltage | 3.6 V |
| Gain-Bandwidth Product | 500 kHz |
| Quiescent Current per Channel | 20 uA |
| Shutdown Current per Channel | 10 nA |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Shutdown Control | Common shutdown function |
| Temperature Grade | Industrial |
| Terminal Form | Through-hole |
| Number of Terminals | 14 terminals |
| Encapsulado | 14-pin rectangular DIP |
| Technology | CMOS |
| Amplifier Type | Single supply, rail-to-rail input/output operational amplifier |
Guía de configuración de pines de TLV2765IN 14-pin rectangular dip
Configuración de pines para TLV2765IN (encapsulado 14-pin rectangular dip). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para TLV2765IN.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
TLV2765IN es adecuado para 6 aplicacións: Portable Sensor Signal Conditioning, Battery-Powered Instrumentation, Industrial Process Measurement, Low-Voltage Active Filtering, Precision Voltage Buffering, Standby and Monitoring Circuitry.
Portable Sensor Signal Conditioning
The TLV2765IN fits low-voltage sensor interfaces where four channels must operate from a 1.8V supply with limited battery capacity. Its approximately 20uA per-channel current and rail-to-rail input behavior help preserve signal range in compact systems. Place the amplifier close to the sensor and conditioning network, then validate the sensor output against the amplifier input range. Shutdown can reduce standby demand to 10nA per channel when the sensing subsystem is not being sampled.
Recomendado
Battery-Powered Instrumentation
The TLV2765IN is useful in handheld or field instrumentation operating from two AA or AAA cells. The 1.8V minimum supply, 500kHz gain-bandwidth product, and approximately 20uA per-channel consumption support analog measurement channels without requiring a high-voltage supply. The common shutdown control allows the instrument to enter a low-power state between readings. Confirm cell-regulation limits, sensor excitation requirements, and the complete analog signal path before finalizing the power architecture.
Recomendado
Industrial Process Measurement
The TLV2765IN supports four-channel analog conditioning in industrial process-measurement equipment when the signal and supply levels fall within its low-voltage range. Rail-to-rail inputs can accommodate sensor outputs near the supply rails, while 500kHz bandwidth is sufficient for many slow process signals and filters. The industrial temperature-grade ordering option suits extended ambient environments. Validation should include input common-mode behavior, output swing, noise, settling time, and isolation from adjacent switching circuitry.
Recomendado
Low-Voltage Active Filtering
The TLV2765IN can implement active low-pass, high-pass, and filtering stages in low-voltage measurement systems. Its 500kHz gain-bandwidth product provides useful closed-loop bandwidth for sensor noise reduction and signal conditioning at moderate frequencies. Four channels reduce component count when several filter sections are required. Keep input and feedback networks close to the relevant amplifier pins, check capacitor types for the intended signal bandwidth, and use the manufacturer stability guidance when driving capacitive loads.
Recomendado
Precision Voltage Buffering
The TLV2765IN can buffer low-voltage sensor and divider outputs where rail-to-rail operation helps preserve signal amplitude. A voltage follower configuration uses the amplifier's high open-loop gain to reduce output loading while maintaining a 1.8V-to-3.6V operating range. The approximately 20uA per-channel supply current is useful in power-constrained designs. Verify offset, input bias current, output-current capability, and settling behavior against the source impedance and required settling time.
Recomendado
Standby and Monitoring Circuitry
The TLV2765IN fits systems that need active analog monitoring during normal operation and very low standby consumption afterward. A common shutdown pin controls all four channels, and shutdown current is approximately 10nA per channel according to the Texas Instruments family documentation. This makes the amplifier useful in periodically sampled sensing systems, threshold monitors, and low-duty-cycle test equipment. Validate shutdown polarity and startup behavior in the system state machine rather than assuming the amplifier is immediately ready after shutdown release.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para TLV2765IN — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | TLV2765IP |
|---|---|---|
| Package | DIP-14 | DIP-14 - same |
| Brand | Texas Instruments | Texas Instruments |
| Number of Channels | 4 circuits | 4 circuits |
| Supply Voltage Range | 1.8V to 3.6V | 1.8V to 3.6V |
| Gain-Bandwidth Product | 500kHz | 500kHz |
| Quiescent Current per Channel | 20uA | 20uA |
| Shutdown Current per Channel | 10nA | 10nA |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail |
| Output Swing | Rail-to-rail | Rail-to-rail |
| Shutdown Control | Common shutdown function | Common shutdown function |
Diferenciadores clave
- Combines four channels with a common shutdown control (frente a TLV2765IP)
- Low-voltage operation with rail-to-rail signal handling (frente a TLV2765IP)
- Through-hole package supports repairable and conventionally assembled boards (frente a TLV2765IPW)
Notas de diseño
Place the supply bypass capacitor and any additional decoupling directly between the supply pins and ground, with the shortest practical return path. Keep amplifier inputs, feedback components, and grounding close to the relevant channel to minimize noise pickup. Because the TLV2765IN is a through-hole DIP, preserve adequate spacing around the package for insertion, soldering, and inspection while keeping sensitive analog traces away from switching-node and high-current return paths.
Do not exceed the 3.6V maximum recommended supply voltage. The approximately 20uA per-channel operating current is suitable for low-power operation, but total supply demand also includes load current, input bias current, and external circuitry. Use the shutdown function for systems that spend significant time inactive, verify its polarity, and account for the time required for the amplifier to become signal-valid after shutdown is released.
Do not leave an unused amplifier input floating. Bias unused non-inverting inputs to a stable common-mode voltage within the input range, or use the manufacturer's recommended unused-channel configuration. Also verify that the intended output voltage remains inside the usable output swing; rail-to-rail inputs do not guarantee ideal rail-to-rail output behavior under every load, output-current, and temperature condition.
The 500kHz gain-bandwidth product makes the TLV2765IN appropriate for low-frequency sensor conditioning, buffering, and moderate-bandwidth filtering rather than high-speed waveform work. Select closed-loop gain and feedback components with the amplifier's frequency and stability characteristics in mind. If driving a capacitive load, add the isolation resistance specified in the manufacturer guidance and verify settling at the required signal bandwidth.
Información de cumplimiento
The component is an industrial-temperature-grade operational amplifier; detailed environmental and substance-compliance classifications were not stated on the manufacturer product-page excerpts. AEC-Q100 is marked not applicable because this ordering option is not identified as an automotive-qualified variant.