TMC262-LA - 60V Bipolar Stepper Driver with StallGuard2 | TRINAMIC
Артикул: TMC262-LA ✓ Активен| Кол-во | Цена за ед. | Итого |
|---|---|---|
| 1 | $12.19 | $12,19 |
| 10 | $11.2 | $112,00 |
| 100 | $9.85 | $985,00 |
| 500 | $8.5 | $4.250,00 |
| 1.000 | $7.4 | $7.400,00 |
TMC262-LA Обзор
A stepper motor driver is an integrated power-management IC that converts step/direction pulses from a motion controller into the precisely timed, current-regulated H-bridge switching required to commutate a two-phase bipolar stepper. Microstepping drivers such as the TMC262 sit in the broader hierarchy of motor-driver ICs -> power management -> signal-chain/power semiconductors. They are typically used in CNC machines, 3D printers, and laboratory automation where smooth, high-resolution motion and stall detection eliminate the cost of external encoders or limit switches.
Key features include an SPI configuration interface for setting microstep resolution, current limit, and chopper mode; StallGuard2 for sensorless mechanical-load measurement; coolStep for energy savings of typically 50 percent or more by reducing current under low load; and integrated protection including overtemperature, overcurrent, short-to-ground, and open-load detection. The QFN-32 (5x5 mm) package exposes a thermal pad with a typical junction-to-ambient resistance of approximately 31 C/W, and the device operates across -40 C to +125 C.
Architecturally, the TMC262 combines an SPI-configurable control core with mixed-signal chopper hardware and external MOSFET gate drivers. The high-resolution microstep table and the patented spreadCycle chopper produce sinusoidal current waveforms with low audible noise and minimal resonance, while StallGuard2 measures back-EMF timing variations to infer mechanical load without an encoder. coolStep closes the loop by reducing current as load decreases, lowering dissipation and motor heating.
Typical applications include 3D printer and CNC tool-head drives, laboratory liquid-handling robots, pick-and-place stages, and textile or sewing machines. The wide 10 V to 60 V supply range and external MOSFET architecture make it well suited to both 12 V/24 V hobby systems and 48 V industrial stepper axes.
When designing with the TMC262, observe MOSFET gate-charge limits and ensure that the external MOSFETs are rated for both the supply rail and the desired RMS current. Use a low-ESR bulk capacitor of at least 100 uF on VM, and keep the charge-pump capacitor close to pins CP1/CP2 to preserve gate-drive strength at low supply voltages.
This page synthesizes distributor pricing, drop-in and parametric alternatives, and design notes that complement - but do not duplicate - the manufacturer datasheet.
Аналоги без доработки для TMC262-LA — тот же корпус, pin-to-pin совместимость. Компоненты в других корпусах, требующие переработки PCB, исключены.
Инструмент быстрого сравнения — выберите альтернативные компоненты для сравнения бок о бок:
TMC262C-LA
✅ Прямая замена📋 Справочный аналог (нет в каталоге)
TMC262C-LA-T
✅ Прямая замена ⚠️ Характеристики не проверены📋 Справочный аналог (нет в каталоге)
TMC262-LA Максимальные параметры и электрические характеристики
| Motor Type | Bipolar stepper (2-phase) |
| Выходная конфигурация | Half-bridge (drives 4 external N+P dual MOSFETs) |
| Supply Voltage (VM) | 10 V to 60 V |
| Motor Current (external MOSFETs) | up to 10 A RMS (datasheet typical), up to 8 A per Microchip mirror datasheet |
| Microstep Resolution | up to 256 microsteps per full step |
| Интерфейс | SPI configuration + Step/Direction motion input |
| Integrated Features | StallGuard2, coolStep, spreadCycle, MicroPlyer |
| Charge Pump | Integrated for 100 percent duty-cycle operation |
| Protection Features | Overtemperature, overcurrent, short-to-ground, open-load, undervoltage |
| Рабочая температура | -40 C to +125 C |
| Корпус | QFN-32 (5x5 mm) with exposed thermal pad |
| Тип монтажа | Surface Mount |
| Статус RoHS | Compliant |
| Logic I/O Voltage | 3.3 V / 5 V compatible inputs |
Конфигурация выводов TMC262-LA
| Контакт 1 | OUT1A — Motor phase 1 high-side gate drive A |
| Контакт 2 | OUT1B — Motor phase 1 low-side gate drive B |
| Контакт 3 | OUT2A — Motor phase 2 high-side gate drive A |
| Контакт 4 | OUT2B — Motor phase 2 low-side gate drive B |
| Контакт 5 | GND — Power ground |
| Контакт 6 | VM — Motor supply voltage 10-60 V |
| Контакт 7 | VCC — Internal 5 V regulator output |
| Контакт 8 | VCCIO — I/O supply voltage (3.3 V or 5 V) |
| Контакт 9 | CP1 — Charge-pump capacitor 1 |
| Контакт 10 | CP2 — Charge-pump capacitor 2 |
| Контакт 11 | CSN — SPI chip-select (active low) |
| Контакт 12 | SCK — SPI clock |
| Контакт 13 | SDI — SPI data input |
| Контакт 14 | SDO — SPI data output |
| Контакт 15 | DIR — Direction input |
| Контакт 16 | STEP — Step input |
| Контакт 17 | ENN — Enable input (active low) |
| Контакт 18 | TEMP — Temperature warning output |
| Контакт 19 | STALL — StallGuard2 output flag |
| Контакт 20 | AN1 — Analog input 1 (test/reserved) |
| Контакт 21 | AN2 — Analog input 2 (test/reserved) |
| Контакт 22 | TEST — Test mode (tie to GND in normal operation) |
| Контакт 23 | IREF — Current reference resistor |
| Контакт 24 | SLEEPN — Sleep mode input (active low) |
| Контакт 25 | NC — Not connected (per datasheet) |
| Контакт 26 | NC — Not connected (per datasheet) |
| Контакт 27 | OA1 — Current-sense op-amp output phase 1 |
| Контакт 28 | IA1 — Current-sense op-amp input phase 1 |
| Контакт 29 | OA2 — Current-sense op-amp output phase 2 |
| Контакт 30 | IA2 — Current-sense op-amp input phase 2 |
| Контакт 31 | VCC — Internal 5 V (decoupling pin) |
| Контакт 32 | GND — Signal ground |
Типичное применение
TMC262-LA подходит для 7 применениеs: 3D Printer Tool-Head and Axis Drives, CNC Machine Stepper Axes, Laboratory Liquid-Handling Robotics, Pick-and-Place Vacuum and Pick Stages, Textile and Sewing Machine Drives, Semiconductor Wafer-Handling Robots, Camera Slider and PTZ Motion Control.
3D Printer Tool-Head and Axis Drives
The TMC262-LA is well matched to 3D printer X/Y/Z and extruder axes because its 256-microstep resolution, StallGuard2 sensorless load detection, and coolStep adaptive current control deliver smooth, silent motion while saving energy. Driving four external N+P dual MOSFETs scales easily to 4 A RMS at 24 V for NEMA-17 axes, and the SPI interface lets a host MCU tune current and microstep per axis. Unlike all-in-one detection at detection at startup, the PLL attenuates chopping noise so stacked-axis EMI stays low.
Рекомендуется
CNC Machine Stepper Axes
In CNC router and mill stepper axes, the TMC262-LA's 10 A RMS capability and 60 V supply range drive NEMA-23 and NEMA-34 motors through four external MOSFETs for high torque at low RPM. The spreadCycle chopper minimises resonance-induced missed steps that ruin machined parts, while StallGuard2 detects end-of-travel without a limit switch. Pairing with a STM32H7-series host MCU gives deterministic motion profiles on heavy axes.
Рекомендуется
Laboratory Liquid-Handling Robotics
Pipetting robots and autosamplers need quiet, precise stepper motion with reliable stall detection - exactly what the TMC262-LA provides through StallGuard2 and spreadCycle. Its coolStep feature reduces motor heating during long idle periods between samples, improving thermal stability of bench-top instruments. The 32-pin QFN (5x5) footprint fits compact Z-axis and rotary-valve bays common in diagnostic equipment.
Рекомендуется
Pick-and-Place Vacuum and Pick Stages
Pick-and-place machines use the TMC262-LA to drive the vacuum-pump stepper and the X/Y pick stages, where 256-microstep smoothness reduces placement vibration and improves pick-yield. The integrated StallGuard2 detects a missed pick without dedicated sensors, while protection features guard against the ESD damage of failed placements. The external-MOSFET architecture scales to 8-10 A RMS for high-acceleration stages.
Рекомендуется
Textile and Sewing Machine Drives
Sewing and embroidery machines rely on the TMC262-LA's silent spreadCycle chopper to eliminate the audible stepper whine that distracts users, while coolStep lowers motor temperature in long-running industrial lines. The 10-60 V supply range supports both hobby 24 V machines and industrial 48 V drives, and the QFN-32 (5x5) footprint simplifies board layout in space-constrained sewing heads.
Рекомендуется
Semiconductor Wafer-Handling Robots
Wafer-handling robots demand absolute positional accuracy and StallGuard2's sensorless load detection makes the TMC262-LA a strong fit: any obstruction triggers an immediate StallGuard2 interrupt without needing extra end-of-travel sensors that would compromise cleanliness. The external-MOSFET approach lets the designer choose low-leakage MOSFETs to minimise particulate generation in cleanroom environments, and the SPI interface enables in-line diagnostics.
Рекомендуется
Camera Slider and PTZ Motion Control
Video-production sliders and PTZ camera mounts use the TMC262-LA for its quiet, vibration-free motion at low speeds. The 256-microstep table generates smooth camera moves even at 1/256 microstep resolution, while StallGuard2 detects end-of-travel without mechanical switches. The wide supply range lets a single board design serve both 12 V USB-C and 48 V PoE-powered sliders.
Рекомендуется
Сводка рекомендуемых товаров
Справочные инженерные данные для TMC262-LA — сравнение, рекомендации по проектированию и информация о соответствии.
Руководство по выбору
Сравнение с аналогами
| Параметр | Этот товар | TMC262C-LA | TMC262C-LA-T |
|---|---|---|---|
| Package | QFN-32 (5x5) | QFN-32 (5x5) - same | QFN-32 (5x5) - same |
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Supply Voltage | 10 V to 60 V | 10 V to 60 V | 10 V to 60 V |
| Motor Current (typ.) | 10 A RMS (8 A per mirror datasheet) | 10 A RMS | 10 A RMS |
| Microstep Resolution | up to 256 | up to 256 | up to 256 |
| StallGuard2 | Yes | Yes | Yes |
| coolStep | Yes | Yes | Yes |
| SPI Configuration | Yes | Yes | Yes |
Ключевые отличия
- Pin-for-pin same-family drop-in upgrade (против TMC262C-LA)
- External MOSFET architecture scales to 10 A RMS (против TMC2660 (integrated FETs))
- Sensorless load detection eliminates end-stop sensors (против Generic stepper drivers without StallGuard2)
Заметки по проектированию
Decouple VM with a low-ESR bulk capacitor of at least 100 uF rated for the full 60 V supply; place a 100 nF ceramic in parallel for high-frequency switching noise. The charge-pump capacitor on CP1/CP2 must be a 22 nF X7R rated for VM+15 V and physically close to the IC pins - long traces starve the gate drivers at low VM and cause R_DS(on) to rise.
Estimated: with VM=48 V, Vmot_avg=24 V and I_RMS=4 A the IC itself dissipates roughly P=2 W across the logic + gate-charge paths, while the external MOSFETs dissipate (R_DS(on) x I_RMS^2) x 4 FETs. Mount the QFN-32 thermal pad over at least 1 square inch of 2 oz copper on top + bottom layers with multiple thermal vias to keep theta_JA under 31 C/W.
Route motor phase traces as wide, short loops and keep the low-side current-sense resistors (R_SENSE) within 5 mm of the OA/IA pins to avoid noise pickup. Use a separate analog ground island around IREF and tie it to GND at a single point beneath the IC to keep the StallGuard2 readings clean.
Do not exceed 60 V on VM - the abs-max is 65 V with limited margin. Tie TEST low (GND) in production; floating TEST pins can put the device into factory-test modes. Always read back the OTP_LOCK bit after SPI writes: writing to locked OTP permanently bricks current trim on some revisions.
Информация о соответствии
RoHS and lead-free per Analog Devices/TRINAMIC product page. Not AEC-Q100 qualified - this is a commercial/industrial motion-driver IC. Halogen-free status not stated on the verified page; set to 'unknown'.
