Mga Produkto (46,000+)

LM2903VQDRQ1 - 36V Dual Automotive Comparator | Texas Instruments
LM2903VQDRQ1

LM2903VQDRQ1 - 36V Dual Automotive Comparator | Texas Instruments

Texas Instruments LM2903VQDRQ1 is a dual differential comparator rated for a 2 V to 36 V supply, operating from -40 °C to +125 °C in an 8-pin SOIC package. The device provides two independent comparison channels with open-collector outputs compatible with TTL, MOS, and CMOS logic. It is qualified to AEC-Q100 Grade 0 and Grade 1 for automotive applications. A comparator is a differential amplifier whose output indicates whether its non-inverting input is above or below its inverting input. The LM2903VQDRQ1 belongs to the comparator hierarchy within analog and mixed-signal integrated circuits. Its high-voltage supply tolerance and automotive qualification make it suitable for monitoring 12 V and 24 V vehicle electrical systems, where input signals can exceed conventional logic supply levels. The LM2903VQDRQ1 supports single-supply operation from 2 V to 36 V or dual-supply operation from ±1 V to ±18 V. Each channel includes an inverting input, a non-inverting input, and an open-collector output. The open-collector architecture requires an external pull-up resistor and permits the output to be pulled up to a logic voltage different from the comparator supply. Supply-current drain is specified as 0.4 mA, supporting low-power monitoring systems. The differential input-voltage range extends to the maximum-rated supply voltage, while the common-mode input range includes ground. These characteristics support threshold detection, overvoltage and undervoltage detection, sensor conditioning, and automotive signal monitoring. The open-collector outputs can sink external-device current when the comparison state is active, while the pull-up network establishes the inactive high state. A typical propagation delay of approximately 1.3 µs is appropriate for general-purpose control rather than high-speed edge detection. Typical uses include battery-pack protection, automotive power-rail supervision, industrial control thresholds, window and sensor-limit comparisons, and interface logic for open-collector buses. In vehicle systems, the wide supply range allows a comparator to operate directly from protected battery-related rails when the preceding circuit provides suitable transient protection. In process-control equipment, the comparator can supervise a transducer signal and provide a pulled-up logic indication to a controller. Design the pull-up resistor to balance output rise time, switching current, power consumption, and the sink-current rating of the open-collector output. Keep the two comparison channels independent even when they share the supply pins. Provide stable supply decoupling close to the device, route sensitive input traces away from switching nodes, and use the manufacturer's pin-description table when assigning PCB tracks. Automotive implementations should also include the transient-protection and layout measures required by the completed vehicle interface. This product page combines the exact ordering information, manufacturer specifications, pin arrangement, drop-in replacement analysis, application guidance, and engineering design notes needed to evaluate the LM2903VQDRQ1 before it is assigned to a PCB or placed on a bill of materials.

RFQ Kontak
LM2903VQPWR - Dual 36V Comparator | Texas Instruments
LM2903VQPWR

LM2903VQPWR - Dual 36V Comparator | Texas Instruments

Texas Instruments LM2903VQPWR is a dual differential comparator containing two independent voltage comparators, a 2 V to 36 V operating-voltage range, and open-collector outputs in an 8-pin TSSOP (PW) package. The device supports single-supply operation and dual-supply operation when the total supply span and voltage relationship meet its operating limits. A dual comparator is an analog integrated circuit that compares two input voltages and produces a digital-level output indicating which input is higher. As a comparator within the broader analog IC and semiconductor hierarchy, the LM2903VQPWR provides the conversion of small analog voltage differences into logic-compatible decisions. Its two independent channels can monitor two thresholds, or they can be combined for window comparison and other system-level functions. The principal features include two independent comparators, a wide 2 V to 36 V supply range, rail-to-rail input capability, open-collector outputs, and an operating temperature range of -40°C to +125°C. The open-collector outputs require an external pull-up resistor and allow several outputs to be connected for wired-AND behavior. This architecture is useful when driving open-drain logic, relay interfaces, or indicators with a compatible pull-up voltage. The LM2903 family is designed for general-purpose comparison rather than continuous analog amplification. Each channel compares an inverting input with a non-inverting input, while its output changes state according to the input relationship. Rail-to-rail input behavior allows the input voltages to approach the supply rails, although common-mode and output-state details should be checked against the manufacturer datasheet for the exact operating conditions. Typical uses include threshold detection, industrial sensor interfaces, overvoltage and undervoltage monitoring, control-system signal conditioning, and open-collector logic interfaces. The 8-pin TSSOP package supports compact surface-mount layouts, while the -40°C to +125°C temperature range makes the device suitable for industrial and automotive-style environments when the complete system requirements support that operating range. For PCB design, reserve the pull-up network required by the open-collector outputs and keep comparator input routing away from high-current switching paths. Account for input common-mode limits, output pull-up voltage, supply decoupling, and logic thresholds in the connected system. The manufacturer pin-description table should be used directly when assigning PCB tracks and confirming the numbering of the PW package. This product page consolidates the core electrical characteristics, replacement options, application guidance, and package-level design considerations into a practical selection reference. It also provides a parameter-by-parameter comparison that helps engineers distinguish standard, automotive, and lead-free orderable variants before committing to a PCB footprint.

RFQ Kontak
LM2903VQPWRG4 - 18V Dual Open-Collector Comparator | TI
LM2903VQPWRG4

LM2903VQPWRG4 - 18V Dual Open-Collector Comparator | TI

Texas Instruments LM2903VQPWRG4 is a dual general-purpose differential comparator with an 18 V supply rating, open-collector outputs, rail-to-rail input capability, and 0.3 microsecond response time in an 8-TSSOP package. The device contains two independent comparator channels and supports single-supply or split-supply operation. A comparator is an analog integrated circuit that evaluates two input voltages and changes its output state according to their relationship. The LM2903 belongs to the comparator hierarchy, where a differential comparator feeds logic-level decision circuits, sensor interfaces, threshold detectors, and industrial control equipment. Its rail-to-rail input behavior is particularly useful when sensing signals near the supply rails. Key features include a low typical supply-current drain of 0.4 mA per comparator, an 18 V maximum supply rating, and 0.3 microsecond response time. The open-collector outputs allow the output node to be pulled up to the system logic voltage, providing flexible voltage-level interfacing. The two channels operate independently, permitting one package to implement two comparison functions or two separated threshold decisions. The V-suffix LM2903 family supports a wide range of supply voltages and retains operation from single or dual supplies. Its common-mode input range can extend close to the supply rails, while the open-collector outputs can sink external-device current when the comparison result is low. These characteristics make the comparator suitable for both low-voltage sensing systems and higher-voltage industrial interfaces. Typical applications include industrial process-limit detection, power-supply sequencing, sensor threshold conditioning, battery monitoring, and overvoltage or undervoltage protection. Two channels can also implement a window comparator by comparing an input signal against separate upper and lower reference thresholds. The 8-TSSOP footprint supports compact surface-mount layouts where channel density and PCB area are important. When designing around the LM2903VQPWRG4, add a pull-up resistor to each open-collector output and account for the output leakage and sink-current limits when choosing its logic level. Keep input and output routing compact, maintain adequate supply decoupling, and verify that all sensed voltages remain within the device's operating limits. This page combines manufacturer specifications, pin-level guidance, drop-in alternatives, application analysis, and design considerations to support faster component selection and PCB implementation.

RFQ Kontak
LM2903VQPWRG4Q1 - 30V Dual Comparator | Texas Instruments
LM2903VQPWRG4Q1

LM2903VQPWRG4Q1 - 30V Dual Comparator | Texas Instruments

The Texas Instruments LM2903VQPWRG4Q1 is an automotive dual differential comparator with two independent open-collector channels, a 30 V maximum supply voltage, and an 8-pin TSSOP package. The LM2903VQPWRG4Q1 supports single-supply or dual-supply operation and is qualified to AEC-Q100 Grade 0 and Grade 1 for automotive electronics. A comparator is an analog integrated circuit that compares two input voltages and changes its output state when the non-inverting input rises above the inverting input. The differential comparator belongs to the broader comparator, analog IC, and semiconductor hierarchies. It is commonly used for threshold detection, overvoltage and undervoltage monitoring, sensor conditioning, and converting analog levels into digital logic signals. The device provides lower offset voltage, higher supply-voltage capability, lower supply current, lower input bias current, lower propagation delay, and improved 2 kV ESD performance than earlier LMx93-family devices. Typical input offset voltage is no more than 7 mV at 25°C, supply current is 0.4 mA per comparator, and nominal response time is 1.3 microseconds. Its open-collector outputs allow wired logic, pull-up resistors, and level translation to the supply voltage used by the receiving logic. Each channel has independent noninverting and inverting inputs, so the two comparators can monitor separate signals or implement two thresholds. The common-emitter open-collector output sinks current from an external pull-up and naturally goes to a high-impedance state when the comparator is inactive. Because the output stage is not push-pull, output rise time depends on the pull-up resistor, total bus capacitance, and leakage current rather than only on internal drive strength. Typical uses include automotive battery monitoring, sensor threshold detection, industrial control inputs, overvoltage and undervoltage protection, and signal conditioning between analog sensors and digital controllers. Single-supply operation simplifies power architecture, while dual-supply operation allows inputs and output pull-ups to reference different voltage domains. The wide 30 V supply range also accommodates 12 V and 24 V automotive electrical environments when the absolute maximum ratings and transient requirements are respected. For PCB design, keep the comparator inputs and power-ground return paths compact, connect the exposed-decoupling route to a low-impedance ground plane, and place the output pull-up resistor near the driven logic input. Avoid routing sensitive input traces beside power outputs or long pull-up traces. Input protection may be required in external automotive connectors, and production designs should validate the complete system for conducted noise, ESD events, supply transients, and open-collector pull-up compatibility. This page combines exact ordering information, automotive qualification details, drop-in comparator choices, application-specific engineering guidance, and a parameter comparison to help engineers select and implement the LM2903VQPWRG4Q1 correctly.

RFQ Kontak
LM2903VQPWRQ1 - Dual 36V Automotive Comparator | Texas Instruments
LM2903VQPWRQ1

LM2903VQPWRQ1 - Dual 36V Automotive Comparator | Texas Instruments

The Texas Instruments LM2903VQPWRQ1 is a dual general-purpose differential comparator in an 8-pin TSSOP package, qualified to AEC-Q100 Grade 0 and Grade 1 for automotive applications. It provides two independent open-collector outputs, operates from single or dual supplies, and supports supply-voltage differences from 2 V to 36 V when used with dual supplies. The typical supply-current drain is 0.4 mA per comparator. A comparator is an analog integrated circuit that evaluates a voltage at its non-inverting input against a voltage at its inverting input and switches its output according to the polarity of that difference. The LM2903 family belongs to the broader hierarchy of differential comparator, analog comparator, linear integrated circuit, and semiconductor. Its open-collector outputs allow the output stage to be pulled up to a local supply or logic rail, providing flexibility for wired-AND arrangements and direct interfacing with TTL, MOS, or CMOS-compatible circuitry. The V-enhanced LM2903-Q1 family is designed for cost-sensitive applications requiring wide supply tolerance, low supply-current drain, and automotive qualification. According to the manufacturer product page, the device offers improved low-offset voltage, higher supply-voltage capability, lower supply current, lower input bias current, lower propagation delay, and improved 2 kV ESD performance compared with earlier LM293, LM393, and LM2903 families. The improved 2 kV ESD capability is especially relevant to chassis-connected and cable-driven automotive systems. Typical uses include battery monitoring, threshold detection, overvoltage and undervoltage protection, window comparators, motor-control interfaces, and signal conditioning. Because each half of the device operates independently, one package can implement two unrelated comparison functions. This reduces component count while preserving separate inputs and outputs for each channel. For PCB design, keep the two comparator channels away from high-current switching paths and high-impedance input traces where practical. Place input-referenced components close to their associated pins, provide an uninterrupted ground return, and use pull-up resistors on both open-collector outputs. Confirm the pull-up voltage, output-sink current, input common-mode range, and supply limits against the manufacturer datasheet before fixing the external component values. This page consolidates the device specification, drop-in alternatives, package-level comparison data, and practical PCB guidance into a design-focused reference. It also identifies which automotive and electrical details must be confirmed in the official manufacturer documentation before production release.

RFQ Kontak
LM2903WDT - Dual Open-Collector Comparator | STMicroelectronics
LM2903WDT

LM2903WDT - Dual Open-Collector Comparator | STMicroelectronics

The STMicroelectronics LM2903WDT is a low-power dual differential voltage comparator with an open-collector output configuration, supplied in an 8-pin SOIC package. The device combines two independent comparator channels, a typical supply current of 0.4 mA, input offset current of 25 nA, and an input offset voltage of 250 mV. Its rail-to-rail input capability and low-power operation make it suitable for general-purpose analog signal conditioning, threshold detection, and industrial control circuits. A voltage comparator is an analog integrated circuit that compares one input voltage with another and changes its output state when the differential input crosses a switching threshold. The LM2903 belongs to the comparator hierarchy, where a comparator IC sits between basic analog signal-conditioning circuits and higher-level control systems. Each channel can compare an external signal against a reference voltage, allowing a logic-compatible indication of whether the signal is above or below the selected threshold. The LM2903WDT provides two comparator channels in one 8-pin SOIC package. Its open-collector outputs can sink current from a pulled-up supply while placing the output in a high-impedance state when inactive. This arrangement supports wired logic, relay-driver interfaces, and systems that require multiple open-collector outputs sharing a bus. The low 0.4 mA supply current is valuable in battery-powered or continuously monitored equipment where comparator power consumption contributes directly to standby energy use. The stated 250 mV input offset voltage and 25 nA input offset current define the practical accuracy limits around the switching point. Input offset voltage is the difference between the two inputs required to move the output through its switching region, while input offset current represents the residual current entering the input terminals. These values should be considered when the application requires a precise switching threshold rather than general threshold detection. Typical uses include battery monitoring, sensor-limit detection, industrial control interfaces, window or level comparators, and low-power monitoring subsystems. The comparator can operate directly from a low-voltage supply and accept signals extending across the supply range, reducing the need for separate input attenuation when the monitored voltage remains within safe absolute limits. The two channels may be used independently or together for window comparison, provided their input and output arrangements satisfy the application requirements. Designers should account for open-collector output behavior by adding an appropriate pull-up resistor and verifying the pull-up voltage against the connected logic. Input pins must remain within the device's permitted common-mode and absolute-maximum limits. Because the offset characteristics contribute uncertainty at the threshold, applications requiring tighter accuracy should add input attenuation, filtering, or external precision references. This page combines the confirmed ordering information with drop-in alternatives, comparison guidance, and practical circuit-design considerations.

RFQ Kontak
LM2903WHYST - Dual Low-Power Voltage Comparator | STMicroelectronics
LM2903WHYST

LM2903WHYST - Dual Low-Power Voltage Comparator | STMicroelectronics

The STMicroelectronics LM2903WHYST is a low-power dual voltage comparator containing two independent comparator channels, a 2 V to 36 V single-supply operating range, and an 8-MiniSO package. Each channel provides an open-collector output, allowing the outputs to be pulled up to a compatible logic supply and used in wired-AND arrangements when connected together. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state according to their relationship. The dual comparator in the LM2903WHYST can perform two independent threshold, window, or level-detection functions. In the power-management hierarchy, this device belongs to the comparator family within amplifier and signal-conditioning integrated circuits. It is intended for low-power sensing where the output must interface with TTL, CMOS, or other digital logic. The principal electrical features include a wide single-supply range of 2 V to 36 V, dual-supply operation from ±1 V to ±18 V, and very low supply current of 0.4 mA independent of supply voltage. The manufacturer documentation also lists a typical input bias current of 25 nA, typical input offset current of ±5 nA, an input common-mode range that includes the negative rail, and a typical low output saturation voltage of 250 mV at 4 mA output current. Each comparator consumes approximately 1 mW when operated from 5 V. The open-collector architecture requires an external pull-up resistor. When the output transistor turns off, the resistor raises the output toward the logic supply; when it turns on, the output is pulled toward ground. The differential input voltage can be large enough for the comparator to be used as a Schmitt trigger or line receiver, while the low quiescent current supports battery-powered equipment. Open-collector outputs can also be wired together, but the resulting common output requires careful pull-up selection and fault-current analysis. Typical uses include industrial sensor interfaces, battery monitoring, overvoltage and undervoltage detection, motor-control thresholds, and general logic-level sensing. The LM2903WHYST is particularly appropriate where two independent decisions are required and where a low-current open-drain interface is preferable to a rail-to-rail push-pull output. In a battery-powered design, the 0.4 mA supply current helps limit continuous overhead, while the broad supply range supports operation from low-voltage cells through industrial rails. Designers should select the external pull-up resistor according to the required logic level, output rise time, and leakage current. The pull-up must connect to a supply that remains within the output ratings of the comparator and the receiving logic device. Input source impedance should remain low enough to prevent bias-current-induced offset errors, and unused comparator channels should be configured according to the manufacturer recommendations rather than left floating. This product page combines the manufacturer's electrical characteristics with package, application, and replacement guidance. It also identifies verified same-package alternatives where pin compatibility can be established, helping engineers shorten qualification work while preserving the electrical behavior of the original LM2903WHYST design.

RFQ Kontak
LM2903WYDT - Dual 2-36V Low-Power Comparator | STMicroelectronics
LM2903WYDT

LM2903WYDT - Dual 2-36V Low-Power Comparator | STMicroelectronics

The STMicroelectronics LM2903WYDT is a dual low-power voltage comparator with two independent channels, a 2 V to 36 V single-supply operating range, approximately 400 uA power consumption, and 25 nA typical input offset voltage in an 8-pin SOIC package. It is designed for industrial threshold detection, sensing, and open-collector interface applications that require wide supply-voltage tolerance. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM2903 belongs to the comparator hierarchy, within analog signal conditioning and interface ICs. Its open-collector outputs can pull external buses or logic inputs down, while external pull-up resistors establish the high output state. Each comparator operates independently, allowing one package to implement two sensing functions. Key features include a wide 2 V to 36 V supply range, low typical quiescent current of 0.4 mA, and a typical input offset voltage of 25 nA. The open-collector output supports wired logic, relay or solenoid interfaces, and compatibility with multiple logic families when suitable pull-up components are used. The SOIC-8 surface-mount package keeps the dual-channel implementation compact while supporting automated board assembly. The two channels provide common-mode input range and input-offset behavior suited to precision threshold detection. Because the outputs are open collector, the transition speed depends partly on output load capacitance, the external pull-up resistance, and the pull-up voltage. Designers should account for these external factors when setting propagation-delay requirements or operating the outputs at high bus speeds. Typical uses include battery-powered monitoring, industrial sensor interfaces, window or level comparison, power-good detection, overvoltage and undervoltage protection, and general-purpose control logic. The broad supply range is especially useful in equipment operating from regulated low-voltage rails or from higher industrial supply rails after suitable protection and decoupling. For reliable operation, place the supply bypass capacitor close to the device, use a pull-up resistor on each open-collector output, and verify that input and output absolute-maximum limits are not exceeded during power transitions. Check input common-mode range and differential input limits against the actual signal excursion, and confirm that the external pull-up voltage remains within the output-pin rating. This product page combines the manufacturer device description, distributor package information, technical characteristics, qualified drop-in alternatives, and practical interface guidance. It supports faster component selection while preserving the pin, voltage, and output-configuration checks required for production designs.

RFQ Kontak
LM2903WYPT - Dual Low-Power Comparator, 36V, TSSOP-8 | ST
LM2903WYPT

LM2903WYPT - Dual Low-Power Comparator, 36V, TSSOP-8 | ST

The STMicroelectronics LM2903WYPT is a low-power dual voltage comparator featuring two independent comparator channels with open-collector outputs, rated for supply voltages from 2V to 36V (or 1V to 18V split supplies), housed in an 8-pin TSSOP package with an operating temperature range of -40C to +125C. A voltage comparator is an analog building block that compares two input voltages and drives its output to indicate which input is higher. Comparators sit within the broader amplifier IC family, alongside op-amps and difference amplifiers, and form a core part of analog signal conditioning chains in power management, sensing, and control systems. The LM2903 family is one of the most widely used comparator families in the industry, valued for single-supply operation and wide voltage tolerance. The LM2903WYPT key features include a wide 2V to 36V single-supply operating range, very low input bias current of 250 nA (typical family figure), and open-collector outputs that support wired-OR configurations and level shifting to logic rails up to 36V. The W-grade variant adds enhanced robustness targeted at automotive and industrial environments, and the part is AEC-Q100 qualified, making it suitable for vehicle-level electronics where reliability over temperature is mandatory. Technically, the device operates from a single supply over a wide voltage range, and operation from split supplies is also possible. The input common-mode range includes ground, allowing the comparator to sense signals near 0V without additional biasing circuitry. The low supply current draw per comparator makes it suitable for battery-powered designs, while the open-collector stage requires an external pull-up resistor to define the output logic level. Typical applications include automotive sensor interfaces and threshold detection, overvoltage and undervoltage supervision in industrial power supplies, window comparators in battery chargers and motor control feedback, and limit detection in consumer and instrumentation circuits where a low-cost, rugged dual comparator is required. When designing with this device, remember to fit a pull-up resistor on each open-collector output; without it, the output cannot reach a defined high state. Input and output voltages should never be taken below the negative supply rail, and response time must be budgeted against the low-power biasing. This page synthesizes distributor listings, drop-in same-family alternatives, AEC-Q100 qualification status, and practical design guidance in one place, going beyond the information found on a typical distributor product card.

RFQ Kontak
LM2903XK - Dual Open-Drain Comparator | Runic Technology
LM2903XK

LM2903XK - Dual Open-Drain Comparator | Runic Technology

Runic Technology LM2903XK is a dual-channel, general-purpose voltage comparator with open-drain outputs, supplied in an 8-pin SOIC package. The device is intended for industrial control and consumer-electronics circuits that compare two input voltages and require a digital, low-side output for interfacing with pull-up-based logic systems. Its dual-channel architecture allows two independent threshold comparisons in one package. A voltage comparator is a semiconductor that evaluates the relationship between two voltages and changes its output state when one input crosses the other. The comparator category belongs to the broader signal-conditioning and interface-IC hierarchy, where an analog voltage decision is converted into a logic-compatible event. The LM2903XK open-drain output can support wired logic, system monitoring, threshold detection, and control functions when paired with an appropriate pull-up resistor. The LM2903XK provides two comparator channels, open-drain output structures, and an 8-SOIC package identified as SOIC-8 with a 0.154-inch, 3.90 mm width. PartGenie classifies the device for industrial-control and consumer-electronics applications. Its listed environmental-handling classification is MSL 3 for 168 hours, while its compliance records identify RoHS3 compliance and no REACH impact. Because the output is open drain, each channel can pull its output node to a defined logic-low state but cannot actively drive a logic-high state. A pull-up resistor or compatible pull-up network is therefore required. This arrangement provides useful flexibility because the output can be referenced to a supply selected by the system designer, while multiple open-drain outputs can share a bus when the electrical conditions and device limits permit. Typical uses include monitoring a power rail against a reference, detecting sensor thresholds, generating reset or fault signals, comparing two analog signals, and implementing simple control loops. The dual-channel format is especially useful when a system requires two related decisions, such as an upper-limit detector and a lower-limit detector, without using separate single-channel packages. The primary PCB considerations are pin orientation, input common-mode limits, output pull-up values, and the voltage and current ratings of the open-drain nodes. Designers should use the manufacturer datasheet pin-description table and electrical characteristics before finalizing input ranges, output sink-current limits, supply limits, and decoupling requirements. A local ground-reference arrangement is important for stable comparator behavior. This product page consolidates the LM2903XK function, package information, compliance records, verified source links, and application guidance. It also identifies confirmed package-related alternatives and clearly separates them from unverified or differently packaged options so that engineers can assess PCB compatibility before making a replacement decision.

RFQ Kontak
LM2903YDT - Dual 36V Comparator, SOIC-8 | STMicroelectronics
LM2903YDT

LM2903YDT - Dual 36V Comparator, SOIC-8 | STMicroelectronics

The STMicroelectronics LM2903YDT is a low-power dual differential voltage comparator with two independent open-collector outputs, a single-supply operating range of +2 V to +36 V, and an 8-pin SOIC package. It is designed for general-purpose signal comparison over wide supply-voltage and input-voltage ranges, making it suitable for industrial, automotive, and embedded control systems. A voltage comparator is an analog interface that compares two input voltages and produces a digital logic result indicating which input is higher. The LM2903 belongs to the comparator hierarchy, which includes differential comparators, analog interface ICs, and semiconductor signal-conditioning devices. Its two independent channels allow one package to perform two separate threshold, sorting, level-detection, or overvoltage-monitoring functions without sharing internal circuitry between channels. Key characteristics include a supply current of 0.4 mA, low input bias current of 25 nA typical, input offset current of ±5 nA typical, and operation from +2 V to +36 V with a single supply or ±1 V to ±18 V with dual supplies. The open-collector outputs allow wired-AND logic and require an external pull-up resistor. Low input current is especially useful when sensing high-impedance sensors because it reduces the input burden and allows the source impedance to determine practical sensitivity. The device compares two differential inputs without saturating at either supply rail. This rail-to-rail comparison behavior supports designs in which the sensed signal approaches ground or the positive supply. Because the outputs are open collector, external pull-ups can establish the logic voltage independently of the comparator supply, allowing interfacing with TTL, CMOS, MCU inputs, relay drivers, or other open-collector loads. The low 0.4 mA supply current also keeps comparator overhead low in continuously powered equipment. Typical applications include industrial sensor thresholding, motor and valve control, battery monitoring, overvoltage detection, window-comparator functions, and digital control systems. The automotive-qualified LM2903YDT variant is particularly appropriate for vehicle electronic modules requiring a wide supply range, low quiescent current, and robust open-collector signaling. Its SOIC-8 package supports conventional reflow assembly and provides adequate pin spacing for straightforward routing. Designers should account for open-collector output behavior, input common-mode range, offset voltage, propagation delay, and supply decoupling. Place the supply bypass capacitor close to the device and use pull-up resistors that satisfy the required rise time without excessive switching current. Verify the selected logic family’s input thresholds and check the comparator’s response time against the application’s switching requirements. This page combines the manufacturer specifications with practical interface guidance, package-aware alternatives, and a parameter-by-parameter comparison. It is intended to help engineers determine whether the LM2903YDT fits a particular dual-comparator design and whether a same-footprint replacement is electrically acceptable.

RFQ Kontak
LM2903YPT - Dual 36V Low-Power Comparator | STMicroelectronics
LM2903YPT

LM2903YPT - Dual 36V Low-Power Comparator | STMicroelectronics

The STMicroelectronics LM2903YPT is a dual low-power voltage comparator with two independent channels, an open-collector output stage, and operation from a single 2 V to 36 V supply or split supplies of ±1 V to ±18 V. The device is packaged in an 8-pin TSSOP and is identified as rail-to-rail by its distributor listing. A voltage comparator is an analog interface IC that compares two input voltages and produces a digital logic state indicating which input is higher. The LM2903 belongs to the comparator hierarchy within analog and mixed-signal semiconductors. Its two channels can operate independently, making it suitable for threshold detection, window sensing, level translation, and basic control loops that require only polarity rather than an analog amplified output. The LM2903YPT features a very low supply current of 0.4 mA, described as independent of supply voltage. Operation at a 5 V supply corresponds to approximately 1 mW per comparator. Its low 25 nA typical input bias current and ±5 nA typical input offset current reduce errors when the sensing source has high source impedance. The open-collector outputs also permit wired connection to a common pull-up when an application requires a shared bus. The LM2903 architecture supports wide supply flexibility while retaining low power consumption. Each comparator has differential inputs and an independently controlled open-collector output. Because the output transistor can remain off, the effective output state depends on the external pull-up resistor, supply voltage, and leakage current. This architecture provides compatibility with digital logic but requires suitable pull-up placement and accounting for bus rise time. Typical uses include industrial sensor interfaces, battery-powered monitoring circuits, overvoltage and undervoltage detection, window comparators, and control systems operating across widely varying supply voltages. Two channels can be combined to form a window detector, with one comparator monitoring the upper threshold and the other monitoring the lower threshold. In automotive, industrial, or instrumentation systems, the low supply current helps limit standby power while the broad supply range simplifies power architecture. A key design consideration is output pull-up selection. The resistor must pull the open-collector node high without exceeding the output current limit, while keeping rise time acceptable for the receiving logic. Input common-mode limits, output timing, and absolute maximum ratings should be checked against the manufacturer datasheet for the exact operating conditions. The unused comparator channel should be configured according to the recommended application guidance rather than left floating. This product page combines the exact LM2903YPT ordering information with technical specifications, package and pin guidance, sourcing instructions, and practical comparison notes. It also highlights the restrictions that matter when evaluating a replacement: voltage range, output architecture, channel count, package footprint, temperature grade, and timing must all be compatible.

RFQ Kontak
LM2903YQ3T - 36V Dual Comparator | STMicroelectronics
LM2903YQ3T

LM2903YQ3T - 36V Dual Comparator | STMicroelectronics

The STMicroelectronics LM2903YQ3T is a low-power dual voltage comparator with two independent comparison channels, a 2 V to 36 V single-supply range, and an open-collector rail-to-rail output in an 8-DFN 2 mm × 2 mm package. Each channel can compare an input signal against another signal, while the open-collector outputs provide flexible interface options for digital and analog control systems. A voltage comparator is a semiconductor device that compares two input voltages and changes its output state when one input crosses the other. The LM2903 belongs to the comparator hierarchy, which includes general-purpose comparators, differential comparators, and analog interface ICs. Its dual-channel architecture lets one device perform two independent threshold decisions, reducing component count in industrial control, automotive electronics, and low-power monitoring systems. Key characteristics include a wide single-supply operating range of 2 V to 36 V, dual-supply operation from ±1 V to ±18 V, and very low supply current of 0.4 mA. The typical input bias current is 25 nA, while the typical input offset current is ±5 nA. The open-collector outputs support wired-AND arrangements and require an external pull-up when the comparator must drive a logic input. Automotive-grade versions of this device family are associated with AEC-Q100 qualification. The two internal comparators are electrically independent, allowing separate signal paths within the same package. Rail-to-rail input behavior and low input bias current are useful when sensing source voltages that vary close to either supply rail. The low supply current also reduces power consumption in battery-powered systems, although propagation delay and output pull-up selection remain important when switching speed is critical. Typical applications include automotive battery and power-rail monitoring, industrial sensor threshold detection, overvoltage and undervoltage protection, window-comparator circuits, and logic-level translation between analog sensing nodes and digital control circuits. Its 2 mm × 2 mm DFN8 package supports compact board layouts when adequate copper area and controlled assembly are available. Designers should verify the complete pin assignment and exposed-pad requirements in the manufacturer datasheet before layout. Place input and output components close to their associated pins, provide a suitable pull-up for each open-collector output, and use stable reference sources when threshold accuracy matters. Confirm that signal amplitudes, common-mode range, supply limits, and automotive qualification requirements suit the target circuit. This product page consolidates the manufacturer electrical characteristics, package details, verified sourcing links, practical application guidance, and drop-in-replacement assessment. It also highlights the key limitation that a replaceable device must match both the 8-DFN footprint and pin behavior, rather than merely offering similar comparator performance.

RFQ Kontak
LM2903YST - Dual 36V Low-Power Comparator | STMicroelectronics
LM2903YST

LM2903YST - Dual 36V Low-Power Comparator | STMicroelectronics

The STMicroelectronics LM2903YST is a dual low-power voltage comparator with two independent open-collector outputs, a 2 V to 36 V single-supply range, and support for dual supplies from ±1 V to ±18 V. The device is packaged in an 8-pin MiniSO/TSSOP package and is intended for low-voltage, low-power signal conditioning, threshold detection, and industrial control applications. A voltage comparator is an analog integrated circuit that compares an input voltage with a reference voltage and changes its output state according to the polarity of the difference. The LM2903 contains two independent comparator channels. Within the broader semiconductor hierarchy, it is an analog comparator, an interface IC, and a signal-conditioning device commonly used between sensors, switching circuits, and digital control logic. Key features include a supply current of 0.4 mA that remains independent of supply voltage, low input bias current of 25 nA typical, and low input offset current of ±5 nA typical. The open-collector outputs permit wired-AND connections and require an external pull-up resistor. A typical propagation delay of 1.3 µs supports threshold and switching functions, while the wide supply range accommodates industrial and automotive-style supply conditions. Each comparator has its own non-inverting input, inverting input, and open-collector output. The channels share the supply and ground pins but remain electrically independent for signal comparison. Operation from a single supply or split dual supplies gives designers flexibility when working with bipolar sensor signals, positive-only rails, or systems whose input range extends close to ground. Typical uses include sensor threshold detection, battery and power-supply monitoring, industrial control interfaces, automotive signal conditioning, window or level comparisons, and general-purpose logic qualification. The low 0.4 mA supply-current characteristic is particularly useful in continuously powered equipment where every increment of standby current affects system architecture. Designers should account for the open-collector output when selecting a pull-up resistor and logic supply voltage. Input common-mode limits, output saturation behavior, and the 1.3 µs response time must also be checked against the propagation delay allowed by the surrounding system. The manufacturer datasheet provides the authoritative pin assignments, electrical limits, and test conditions. This page combines operating limits, package details, comparison data, replacement guidance, and practical design notes to support component selection, schematic review, PCB implementation, and sourcing for the LM2903YST.

RFQ Kontak
LM2904ADMG - Dual 26V Low-Power Op Amp | onsemi
LM2904ADMG

LM2904ADMG - Dual 26V Low-Power Op Amp | onsemi

The onsemi LM2904ADMG is a dual, general-purpose operational amplifier designed for low-power signal-conditioning applications over a 3 V to 26 V supply range. It provides two amplifier circuits, a common-mode input range that extends to ground or VEE, and operation from either a single supply or split supplies. The device is supplied in an 8-MSOP package and is specified for temperatures from -40°C to +105°C. An operational amplifier is an analog signal-processing IC that uses high open-loop gain to amplify the difference between two input voltages. The LM2904 family belongs to the broader hierarchy of voltage-feedback operational amplifiers, analog amplifiers, and integrated signal-chain devices. Its common-mode capability makes it useful when signals approach the lower supply rail, while dual integration reduces board area in circuits requiring two independent amplifier channels. Key operating characteristics include a low-power architecture, a 3 V to 26 V supply-voltage capability, and a slew rate of 0.6 V/µs. The 8-MSOP package provides a compact surface-mount option for industrial and embedded equipment. Its specified temperature range supports applications across extended commercial and industrial environments. Designers should verify gain-bandwidth, input-bias-current, output-current, noise, and input-offset parameters against their operating conditions before finalizing a high-impedance or precision design. The LM2904ADMG uses the circuit design established for quad operational amplifiers, with two amplifiers per package. Its common-mode input voltage range extending toward ground or VEE is particularly useful in single-supply sensor interfaces, transimpedance stages, filters, and low-level signal amplifiers. The split-supply option permits operation around a zero-volt reference, while single-supply operation simplifies portable and industrial control systems. Typical applications include current monitoring, sensor conditioning, audio preamplification, active filtering, and general-purpose analog signal processing. In a current-sensing application, the device can amplify the voltage developed across a low-value shunt while operating from a split supply. In a sensor interface, the common-mode range allows closer proximity to the lower rail than a conventional bipolar input amplifier. Input and output stability should be checked with the external resistor and capacitance values used in the final circuit. A key design consideration is power-supply decoupling. Place a suitable bypass capacitor close to the supply pins and route return current through a low-impedance ground path. Avoid excessive output loading and confirm that the selected feedback network preserves the required gain-bandwidth and phase-margin behavior. For AC-coupled inputs, add suitable input bias-current compensation when source resistance is high. This page combines the LM2904ADMG electrical identity, package and temperature information with replacement guidance, comparison parameters, and practical design considerations. It also identifies which replacement candidates preserve the 8-MSOP footprint and where application-specific validation remains necessary.

RFQ Kontak
LM2904ADMR2G - Dual 1 MHz Op Amp, 8-MSOP | onsemi
LM2904ADMR2G

LM2904ADMR2G - Dual 1 MHz Op Amp, 8-MSOP | onsemi

onsemi LM2904ADMR2G is a dual general-purpose operational amplifier with two amplifiers in an 8-MSOP package. It operates from single or split supplies, accepts input common-mode voltages extending to ground or VEE, and provides approximately 1 MHz gain-bandwidth product for general analog signal conditioning. The device is specified for low supply-current drain, low input offset voltage, low input bias current, and internal frequency compensation, making it suitable for applications that do not require rail-to-rail input or output operation. A dual operational amplifier combines two independent amplifier channels in one package. Operational amplifiers are active analog devices used to amplify, buffer, compare, or filter signals. They belong to the broader semiconductor hierarchy of integrated circuits, analog ICs, amplifiers, and operational amplifiers. The LM2904 family is commonly used for industrial control, sensor interfaces, audio signal paths, and low-frequency analog processing where economical dual-channel operation is useful. Key characteristics include a 3 MHz? No. The device has a 1 MHz gain-bandwidth product according to the manufacturer product description, low power drain, common-mode input voltage range extending to ground/VEE, and support for both single-supply and split-supply operation. The 8-MSOP package provides a compact surface-mount footprint for dual-channel analog designs. The LM2904ADMR2G is an active onsemi part according to the listed product information. The LM2904ADMR2G uses internally compensated bipolar amplifier circuits. Internal compensation removes the need for an external frequency-compensation network in ordinary closed-loop configurations. Its common-mode behavior is appropriate for many industrial and embedded systems where inputs remain above the negative supply rail, but the design should be checked against the datasheet limits before operating close to the positive rail or outside the specified supply range. Typical uses include instrumentation buffers, sensor amplifiers, active filters, comparators, audio preamplifier stages, and low-frequency control loops. In a single-supply system, the negative supply pin is connected to ground, while split-supply systems can use positive and negative rails. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured according to the datasheet guidance. The principal design consideration is common-mode and output-range limitation. Unlike modern rail-to-rail-input amplifiers, the LM2904 family is not intended to cover the entire supply range at the input. Verify input common-mode voltage, output swing, supply current, stability, and noise performance against the application requirements. This page summarizes the part family, package, pinout, application considerations, and engineering-focused comparisons for design review and sourcing.

RFQ Kontak
LM2904AHYPT - Dual Low-Power Op Amp | STMicroelectronics
LM2904AHYPT

LM2904AHYPT - Dual Low-Power Op Amp | STMicroelectronics

STMicroelectronics LM2904AHYPT is a low-power, dual bipolar operational amplifier with two independent amplifiers, internally compensated frequency compensation, and an 8-TSSOP package. The device is designed for general-purpose signal-conditioning applications where two amplifiers are required on one board. The verified product information identifies a single-ended, two-circuit amplifier configuration in an 8-pin TSSOP. A dual operational amplifier combines two independent amplifier sections in one package. In the broader semiconductor hierarchy, an operational amplifier is an analog integrated circuit used within the amplifier and signal-conditioning family. Each LM2904AHYPT section provides gain, filtering, buffering, or error amplification, while the common package can reduce board area and simplify component procurement for dual-channel circuits. The principal advantages of this device are its low-power bipolar construction, dual-channel organization, and internally compensated architecture. Internal compensation removes the need for external frequency-compensation components in standard closed-loop operation. The 8-TSSOP package also offers a compact surface-mount format suitable for high-density analog and embedded-control boards. These characteristics make the device useful when a general-purpose amplifier must operate without external compensation networks. Each amplifier section operates independently, allowing one channel to process a sensor signal while the other handles a control, feedback, or monitoring function. The LM2904 family is associated with approximately 100 dB open-loop gain, 1.1 MHz gain-bandwidth behavior, and 20 nA input bias current. Since the exact limits for every electrical condition are not listed on the product page, designers should confirm voltage, current, common-mode, and temperature limits against the manufacturer datasheet before final circuit sign-off. Typical uses include low-frequency sensor conditioning, buffer stages, active filters, differential signal amplification, and general embedded analog interfaces. Because the package contains two amplifiers, the device can consolidate matching channels in instrumentation, industrial control, audio preamplification, and test-equipment input stages. TSSOP-8 placement is particularly useful when component count and routing density are important. For layout, place each decoupling capacitor close to the corresponding supply pins and route input and feedback paths away from switching nodes. Confirm output swing, input common-mode range, stability, and load drive at the actual supply voltage. If a replacement uses the same footprint, verify that the enable, shutdown, slew-rate, and output-current characteristics remain compatible with the original design. This page combines the manufacturer device identity, verified distributor descriptions, package information, family-level operating characteristics, and practical replacement guidance into an engineering-focused reference for evaluating the LM2904AHYPT.

RFQ Kontak
LM2904AM8-13 - Dual 700 kHz Op Amp | Diodes Incorporated
LM2904AM8-13

LM2904AM8-13 - Dual 700 kHz Op Amp | Diodes Incorporated

Diodes Incorporated LM2904AM8-13 is a dual general-purpose operational amplifier with a 700 kHz gain-bandwidth product, supplied in an 8-MSOP package. The device contains two independent, high-gain amplifiers and supports operation from a single supply or split supplies. Its specified operating range extends to ±18 V, equivalent to a total supply voltage of 36 V. This combination of dual-channel operation, wide supply capability, and surface-mount packaging makes the LM2904AM8-13 suitable for general-purpose signal conditioning across industrial, instrumentation, analog control, and embedded systems. An operational amplifier is a high-gain differential amplifier that uses negative feedback to control gain, filtering, amplification, buffering, or analog signal conversion. The dual-amplifier configuration reduces the number of active devices and board area needed when two independent analog channels are required. The LM2904AM8-13 belongs to the operational-amplifier hierarchy, where it sits below precision instrumentation amplifiers and above general-purpose discrete analog signal-conditioning functions. The LM2904 series is identified as a general-purpose amplifier family with very low input-offset voltage relative to many older general-purpose op amps. The two channels share an 8-MSOP package while retaining independent inputs and outputs. A 700 kHz gain-bandwidth product supports general-purpose closed-loop operation at moderate signal frequencies, and the ±18 V supply capability provides useful headroom for circuits using higher signal amplitudes. These characteristics make the part appropriate where low cost, channel density, and supply-voltage flexibility are more important than rail-to-rail input or output operation. The common operating topology places positive and negative feedback around each amplifier, setting closed-loop gain through external resistors. Because the device is intended for broad industrial signal conditioning, designers should verify the required input common-mode range, output swing, output-current capability, input-bias behavior, and stability against the exact operating conditions. The manufacturer datasheet provides the electrical limits and characteristic curves needed to select suitable feedback resistors, bypass capacitors, and external load conditions. Typical uses include sensor-interface conditioning, low-frequency active filters, differential-input stages, transducer amplifiers, analog control loops, and general instrumentation. Industrial data-acquisition systems can use one channel for signal conditioning while using the second channel for biasing, monitoring, or an auxiliary gain stage. The device is also appropriate for compact embedded analog subsystems where an 8-MSOP package reduces board footprint compared with two separate single-amplifier packages. When laying out the circuit, place bypass capacitors close to the supply pins and route feedback components close to their associated amplifier inputs and outputs. Avoid long parallel feedback traces, particularly when operating near the device's 700 kHz gain-bandwidth limit. Check whether the input source can develop voltages outside the specified common-mode range, because general-purpose op amps are not automatically rail-to-rail devices. This product page combines the LM2904AM8-13 operating characteristics with package guidance, application engineering notes, and a parameter-by-parameter comparison framework. It is intended to help engineers identify design constraints quickly while preserving the distinction between published device specifications and application-specific engineering judgments.

RFQ Kontak
LM2904AN - Dual Op-Amp, 3-26V Single Supply | onsemi
LM2904AN

LM2904AN - Dual Op-Amp, 3-26V Single Supply | onsemi

The onsemi LM2904AN is a single-supply dual operational amplifier with two independent general-purpose amplifier circuits in an 8-pin PDIP (DIP-8) through-hole package, operating from a 3V to 26V supply range. According to the TI product family page, the LM2904 class delivers approximately 700 kHz of gain-bandwidth, and the onsemi version is characterized as a low-power dual op-amp with a common-mode input voltage range that extends to ground/VEE. A dual operational amplifier is an analog integrated circuit that houses two complete op-amp cores on a single silicon die, sharing one set of supply pins. In the voltage-regulator-to-amplifier hierarchy of signal-chain components, the op-amp sits between the passive components and the dedicated precision amplifier or instrumentation amplifier: it performs gain, buffering, filtering, and comparison functions that passive networks alone cannot achieve. Single-supply op-amps like the LM2904AN are designed so their input common-mode range includes the negative rail, simplifying circuits powered from a single positive rail such as 5V, 12V, or 24V industrial supplies. Key features of the LM2904AN include low power drain, single-supply or split-supply operation, input common-mode range extending down to the negative rail, and the industry-standard DIP-8 pinout shared across the LM358/LM2904 family. The wide 3V to 26V supply range covers 5V logic systems, 12V automotive rails, and 24V industrial buses without redesign. Technically, the two amplifiers are matched on a common substrate, ensuring closely tracking parameters over temperature. The output stage is designed for single-supply operation where the output can swing close to ground under light loads. Because the LM2904 is a low-cost, general-purpose part, designers should observe its class-B output behavior near the lower rail and its moderate slew rate when applying it to high-frequency or precision tasks. Typical applications include industrial sensor signal conditioning, transducer amplifier front ends, DC gain blocks, active filters, comparators with hysteresis, and low-frequency audio preamplifiers in through-hole prototypes and repair work where the PDIP package simplifies hand soldering and socketing. For design, provide adequate supply decoupling (100 nF ceramic close to pin 8 and pin 4) and avoid capacitive loads above roughly 100 pF without series isolation resistance to prevent oscillation. This page adds value beyond the manufacturer datasheet by combining distributor availability data, drop-in alternatives, a parametric comparison table, and practical design notes in one place.

RFQ Kontak
LM2904ANG - Dual 8-PDIP General-Purpose Op Amp | onsemi
LM2904ANG

LM2904ANG - Dual 8-PDIP General-Purpose Op Amp | onsemi

The onsemi LM2904ANG is a dual, general-purpose operational amplifier packaged in an 8-pin plastic DIP. It provides two amplifier circuits per package, a 0.6 V/µs slew rate, and a 1 MHz gain-bandwidth product. The device supports single-supply or split-supply operation and has a common-mode input range that extends toward ground or VEE, making it suitable for conventional industrial and signal-conditioning circuits. An operational amplifier is a high-gain, low-output-impedance active device used to amplify voltage differences between two inputs. The LM2904 family belongs to the broader analog IC hierarchy of operational amplifiers, linear amplifiers, and analog signal-conditioning ICs. Its dual construction allows two independent amplifier channels in one package, reducing board area in designs that require multiple analog signal paths. The principal characteristics include two integrated circuits, a general-purpose amplifier architecture, a 0.6 V/µs slew rate, and a 1 MHz gain-bandwidth product. The common-mode input capability extending to ground or VEE is important for single-supply designs because it permits the amplifier to process input signals near the lower supply rail. Low power drain also makes the device suitable for battery-operated and low-power equipment when appropriately configured. The LM2904ANG is designed for general-purpose applications rather than precision or high-speed signal processing. Its 1 MHz gain-bandwidth product is adequate for audio, sensing interfaces, control loops, and low-frequency analog amplification. Because the device is listed as obsolete, engineers should also evaluate current-family alternatives when new production designs require an active lifecycle product. Typical uses include dual-stage sensor conditioning, low-frequency active filters, industrial control signal amplification, audio preamplification, and generic voltage-feedback stages. In each circuit, feedback components establish the closed-loop gain, while the supply rails and input common-mode range must remain within the operating conditions specified by the manufacturer. A practical design consideration is input bias-current compensation. The manufacturer documentation should be consulted for the recommended source impedance and compensation arrangement, particularly when driving low-impedance sources. PCB layout should keep feedback loops short and provide adequate ground-return paths to prevent additional noise or instability. This product page combines the LM2904ANG electrical characteristics, package information, lifecycle status, comparison data, and practical replacement guidance. It also identifies pin-compatible options for obsolete designs while helping engineers distinguish between a true board-level replacement and a merely similar amplifier.

RFQ Kontak
LM2904AQM8-13 - Dual 36V Op Amp, 500uA | Diodes
LM2904AQM8-13

LM2904AQM8-13 - Dual 36V Op Amp, 500uA | Diodes

Diodes Incorporated LM2904AQM8-13 is an automotive-compliant, dual operational amplifier packaged in an 8-MSOP. The device operates from a 36 V maximum supply, provides two amplifier channels, and is specified for 500 uA supply current, 20 nA input bias current, and 100 dB open-loop gain. Its 8-MSOP package supports compact analog signal-conditioning layouts while retaining the industry-standard dual-op-amp pin arrangement described for the LM2904Q family. An operational amplifier, or op amp, is a high-gain analog amplifier used to amplify voltage differences, buffer sensors, drive external loads, and implement active filters. The LM2904 belongs to the broader general-purpose amplifier hierarchy, which includes dual and quad operational amplifiers used in signal-chain, instrumentation, and control applications. Its wide supply range makes it useful where signal levels and supply conditions vary substantially. The headline characteristics make the LM2904AQM8-13 appropriate for low-power signal conditioning. A 36 V maximum supply expands the usable operating envelope, while 500 uA supply current limits the power burden of dual-channel circuits. The 20 nA input bias current reduces loading on high-impedance sources, and 100 dB open-loop gain provides useful amplification when feedback establishes the closed-loop gain. The LM2904Q family uses industry-standard pin arrangements and is available in multiple small-outline packages. The M8-13 ordering option places this dual amplifier in an 8-MSOP. For conventional non-unity-gain operation, feedback networks define the closed-loop response, while input common-mode and output-swing limits must remain within the datasheet operating envelope. Decoupling should be placed close to the supply pins to reduce supply-borne noise. Typical uses include low-side current monitoring, transducer and sensor interfaces, buffered analog measurements, active filtering, and general-purpose signal conditioning in automotive or industrial equipment. The dual configuration reduces board area when two independent analog channels are required, although crossover distortion is important when similar signals are amplified simultaneously at high output levels. Designers should verify input bias current, input offset voltage, output swing, common-mode range, and stability requirements against the complete operating conditions. Avoid relying on rail-to-rail operation unless the applicable LM2904 datasheet explicitly confirms the required input or output range. Decoupling capacitors, grounding, and feedback-component placement remain important even though the amplifier itself has a low supply current of 500 uA. This product page consolidates the verified order information, package details, technical attributes, application guidance, and qualified drop-in comparison points. It is designed to help engineers determine whether the LM2904AQM8-13 fits a compact, dual-channel automotive signal-conditioning design and to identify the closest pin-compatible alternatives before a board-level substitution.

RFQ Kontak
LM2904AQS-13 - Dual 36V Automotive Op Amp | Diodes
LM2904AQS-13

LM2904AQS-13 - Dual 36V Automotive Op Amp | Diodes

The Diodes Incorporated LM2904AQS-13 is a dual general-purpose operational amplifier in an 8-pin SO package, with a 2 V to 36 V supply span, 700 kHz gain-bandwidth product, and low input offset voltage. The LM2904AQS-13 is an automotive-compliant version of the LM2904A family, making it suitable for dual-amplifier signal-conditioning circuits operating from low-voltage industrial systems through 36 V automotive environments. Its operating-amplifier configuration provides two independent amplifiers in one package. An operational amplifier is a high-gain, differential-input analog amplifier used in the broader hierarchy of amplifier ICs, analog signal-chain ICs, and semiconductor devices. Its differential input allows a small voltage difference to be amplified relative to a feedback-defined reference. Common uses include voltage buffers, sensor amplification, active filters, comparators, and transducer-signal conditioning. The LM2904AQS-13 combines two amplifier channels in one SO-8 package, reducing board area compared with discrete single amplifiers. The device operates from 2 V to 36 V, tolerating a wide range of supply conditions. Its 700 kHz gain-bandwidth product supports general-purpose low-frequency signal amplification, while the listed 20 nA input bias current and 2 mV input offset voltage help define its suitability for moderate-accuracy sensing and feedback networks. The Diodes listing also identifies a 100 dB open-loop gain metric and approximately 500 uA supply-current class, which make the amplifier practical for low- and moderate-frequency industrial and automotive circuits. The LM2904AQ family is identified by Diodes Incorporated as automotive compliant. The S suffix in LM2904AQS-13 identifies the SO-8 package option, while -13 identifies the supplier packaging format. This dual-channel configuration allows one package to implement two independent amplifier stages, reducing component count when a board requires signal buffering, differential amplification, active filtering, or two sensing channels. Typical applications include 5 V and 12 V sensor interfaces, automotive transponder and battery-management signal conditioning, industrial process-control inputs, active low-pass filters, and general dual-amplifier boards. The wide 36 V supply capability is particularly useful where signal nodes can experience industrial transients or automotive battery-related voltages, provided the design keeps every pin within the device's absolute maximum ratings. Design the feedback network for the intended closed-loop bandwidth, keep input and output signals within the common-mode range, and bypass the supply pins close to the package. Decoupling capacitors should be placed at the IC rather than at the power-source entry point. If the amplifier drives capacitive loads, add an isolation resistor and verify stability and output-current margin in the final board layout. This page combines package, electrical, automotive-compliance, cross-reference, and replacement information with practical guidance for dual op-amp layouts. It helps engineers distinguish the exact automotive SO-8 device from broader LM2904 variants, package variants, and functional alternatives that may require different qualification or footprint review.

RFQ Kontak
LM2904AQTH-13 - Dual 36V Automotive Op Amp | Diodes Incorporated
LM2904AQTH-13

LM2904AQTH-13 - Dual 36V Automotive Op Amp | Diodes Incorporated

The Diodes Incorporated LM2904AQTH-13 is a dual general-purpose operational amplifier with two independent amplifier channels, a 36 V supply rating, and an 8-pin TSSOP package. It is an automotive-compliant member of the LM2904AQ family and uses green mold compound as standard. An operational amplifier, commonly called an op amp, is an analog integrated circuit that compares an inverting input with a non-inverting input and drives its output toward the difference between them, amplified by a high open-loop gain. The LM2904AQ family contains independent dual amplifiers designed for general-purpose signal conditioning. Its two channels can process separate signals or be configured together for differential, filtering, comparator-style, and amplifier functions. The LM2904AQTH-13 combines two amplifier circuits in one compact package. Manufacturer listings identify a maximum supply voltage of 36 V, a supply current of 500 uA, an input bias current of 20 nA, and a 100 dB listed performance rating. These characteristics support low-power signal-chain designs operating from higher-voltage rails than typical 5 V or 3.3 V analog circuits, including industrial sensing, vehicle electronics, instrumentation, and low-level signal conditioning. The device belongs to the LM290xAQ automotive-compliant dual and quad operational-amplifier family. The LM2904Q and LM2904AQ dual versions are offered in SO-8, TSSOP-8, and MSOP-8 package options, while quad LM2902 devices use 14-pin packages. Industry-standard pinouts and green mold compound support compact surface-mount implementation and environmentally conscious manufacturing practices. Typical applications include automotive sensor interfaces, industrial transducers, battery-powered monitoring equipment, current sensing, signal amplification, and active filtering. The two independent channels allow one device to handle a differential measurement path or two related analog channels while reducing component count. Designers should still verify input common-mode range, output swing, stability, and absolute maximum ratings for the chosen operating conditions. For PCB design, place input, output, bypass, and compensation components close to their associated pins, then observe the pinout and layout guidance in the manufacturer datasheet. A clean grounding strategy and short feedback routes are especially important because long traces can introduce parasitic feedback, offset, and instability in high-gain amplifier configurations. This product page combines package, application, sourcing, and replacement guidance with practical design considerations. It is intended to help engineers identify the correct automotive dual op amp, verify the 8-pin TSSOP footprint, compare pin-compatible family options, and plan a stable surface-mount implementation without changing the PCB land pattern.

RFQ Kontak
LM2904AS-13 - Dual Precision Op Amp | Diodes Inc.
LM2904AS-13

LM2904AS-13 - Dual Precision Op Amp | Diodes Inc.

Diodes Incorporated LM2904AS-13 is a dual operational amplifier with two amplifier channels, a 3 V to 36 V supply range, 1 mV input offset voltage, 100 dB open-loop gain, 1.1 MHz gain-bandwidth product, and 20 nA input bias current. The device is supplied in an 8-pin SO package and is characterized for operation from -40°C to +125°C. An operational amplifier is a high-gain analog signal-conditioning IC used to amplify voltage differences, buffer sensor outputs, implement active filters, and serve as the input stage of control and measurement systems. In the broader semiconductor hierarchy, the LM2904 belongs to the amplifier IC family, specifically low-power general-purpose operational amplifiers designed for single or dual supply operation. The two-channel configuration lets one package support independent signal paths while reducing board area and the number of required components. A 100 dB open-loop gain supports accurate amplification of small signals, while the 1.1 MHz gain-bandwidth product provides useful bandwidth for common low-frequency and moderate-frequency analog tasks. The stated 20 nA input bias current is particularly relevant when the source impedance is high. The 3 V to 36 V supply span permits operation from conventional single-supply rails through higher industrial supply voltages. Its specified 1 mV input offset supports applications where input-referred error must be controlled relative to the signal level. The -40°C to +125°C characterization provides a broad temperature range for industrial equipment, instrumentation, automotive-adjacent circuitry, and other systems requiring stable operation over extended environmental conditions. Typical uses include transducer-signal conditioning, active audio and control paths, low-frequency filter stages, sensor amplification, and general dual-amplifier circuits. The SO-8 package is suitable for conventional surface-mount assembly, and the manufacturer states that the LM2904/LM2902 family uses green mold compound as standard. When laying out a circuit, keep input and feedback paths short, provide stable bypassing close to the supply pins, and confirm common-mode and output-swing limits at the selected supply voltage and load. Decoupling capacitors should be placed using standard op-amp layout practice to minimize parasitic feedback and unstable operation. This product page combines the manufacturer specification summary, distributor identification, lifecycle-relevant sourcing information, and practical application guidance. It also documents the verified limits of the available drop-in comparison set so engineers can distinguish confirmed same-footprint choices from related LM2904-family devices that require package or qualification review.

RFQ Kontak