Mga Produkto (46,000+)

LM2904ATH-13 - Dual General-Purpose Op Amp | Diodes Incorporated
LM2904ATH-13

LM2904ATH-13 - Dual General-Purpose Op Amp | Diodes Incorporated

The Diodes Incorporated LM2904ATH-13 is a dual, general-purpose operational amplifier packaged in an 8-pin TSSOP. It is intended for single-supply or dual-supply signal-conditioning applications and uses the widely recognized LM2904 amplifier architecture. The device operates from a single supply up to 36 V or from split supplies totaling 36 V, equivalent to ±18 V, while providing two amplifiers in one package. The LM2904 family is intended for general-purpose amplifier, comparator, and voltage-control applications where economy, wide supply-voltage operation, and straightforward PCB implementation are important. An operational amplifier is an analog building block that amplifies the difference between two input voltages. Within the broader semiconductor hierarchy, this product is a general-purpose operational amplifier, or op amp, used in analog signal chains, feedback-control loops, sensor interfaces, and buffer stages. The dual configuration allows one IC to implement two independent amplifier channels, reducing board area and simplifying designs that compare, amplify, filter, or condition two signals. The LM2904ATH-13 provides two independent channels with high open-loop gain and approximately 700 kHz gain-bandwidth performance. Its general-purpose positioning makes it suitable for audio preamplification, transducer conditioning, DC signal amplification, and low-to-moderate-frequency control applications. The 8-pin TSSOP package supports compact surface-mount layouts, while the tape-and-reel suffix identifies the production packing format. Exact input-offset, input-bias-current, output-swing, noise, and temperature limits must be confirmed against the manufacturer datasheet for the exact ordering code. The architecture is suited to conventional single-supply operation because the device can operate close to the positive rail while its output approaches the negative rail. Input common-mode range, output swing, slew rate, and stability conditions still determine whether a particular gain, load, and bypass-capacitor arrangement will meet the design objective. Decoupling should be placed close to the supply pins, and feedback components should be kept compact to minimize parasitic coupling and instability risk. Typical uses include low-level audio stages, current-to-voltage conversion for sensor outputs, general comparator configurations, small-signal amplification, and feedback control around slower feedback loops. The two independent channels can also be configured as comparators, buffers, amplifiers, or differential amplifier sections where their internal characteristics permit the intended operation. Applications requiring very low offset, low noise, high speed, low power, or rail-to-rail output should not assume that a general-purpose LM2904 is the optimal choice. For a robust design, begin with the manufacturer pin configuration and confirm the absolute-maximum ratings, common-mode limits, output-current capability, and recommended external-component values. Avoid using component-marking variants as substitutes without checking the exact pinout, supply range, temperature grade, and package. The TSSOP footprint also requires careful lead pitch and solder-joint inspection because its closely spaced leads are more difficult to inspect than wide-lead SOIC packages. This product page combines the LM2904ATH-13 ordering information, a pin-compatible replacement framework, and practical analog-layout guidance. It highlights the critical decisions engineers must make when reusing an existing 8-pin TSSOP footprint while preserving supply-voltage, common-mode, output-swing, temperature, and load-current requirements.

RFQ Kontak
LM2904AVQDRG4 - Dual 36V 1MHz Op Amp | Texas Instruments
LM2904AVQDRG4

LM2904AVQDRG4 - Dual 36V 1MHz Op Amp | Texas Instruments

Texas Instruments LM2904AVQDRG4 is a dual, general-purpose operational amplifier with two independent channels, a 1 MHz gain-bandwidth product, and operation from a single supply up to 26 V or split supplies up to 36 V total. The device is packaged in an 8-SOIC package and is supplied on tape and reel. An operational amplifier, or op amp, is a high-gain analog signal-conditioning component that compares its inverting and non-inverting inputs and drives its output toward the difference between them. The LM2904 belongs to the broader hierarchy of dual operational amplifiers, analog amplifiers, integrated circuits, and general-purpose analog signal-processing devices. Its two channels share power pins but otherwise operate independently, allowing one package to provide amplification, buffering, filtering, or comparison functions. The principal benefits are a 1 MHz gain-bandwidth product, a 0.3 V/µs slew rate, and low supply-current drain of approximately 0.7 mA per amplifier. Each amplifier includes frequency compensation and is designed for operation from single or split supplies. The input common-mode range includes ground, which supports common single-supply signal-conditioning arrangements. The automotive-qualified ordering option is identified by the Q designation in the part number, although qualification documentation should be checked for the specific production configuration. The internal architecture is designed for dependable general-purpose operation with a useful combination of gain, bandwidth, input range, and supply flexibility. A typical noninverting amplifier gain of 100 has a closed-loop bandwidth of approximately 10 kHz, while a unity-gain configuration supports signal bandwidth up to the device's stated 1 MHz gain-bandwidth product. These figures make the amplifier suitable for slow sensor signals, audio-frequency circuits, feedback-control loops, and general analog conditioning rather than high-speed data acquisition. Typical applications include industrial sensor interfaces, automotive signal-conditioning modules, low-frequency active filters, audio preamplifier stages, current sensing with resistive shunts, and dual-rail buffer circuits. Two independent channels can process complementary signals or perform separate functions, reducing component count and conserving board area compared with two single amplifiers. When designing the circuit, check input and output common-mode limits at the actual supply voltage. Load output signals through appropriate biasing, use a stable reference for precision offset-sensitive measurements, and avoid operating the amplifier near supply-rail limits without confirming the input and output ranges. Place decoupling capacitors close to the power pins and keep feedback traces short to reduce oscillation and noise pickup. This page consolidates the device identity, ordering information, package details, pin assignment, engineering alternatives, and practical design guidance needed to evaluate the LM2904AVQDRG4 for a new analog circuit.

RFQ Kontak
LM2904AVQDRG4Q1 - 26V Dual 700kHz Op Amp | Texas Instruments
LM2904AVQDRG4Q1

LM2904AVQDRG4Q1 - 26V Dual 700kHz Op Amp | Texas Instruments

The Texas Instruments LM2904AVQDRG4Q1 is an automotive-grade, dual general-purpose operational amplifier with a 26 V supply rating, 700 kHz gain-bandwidth product, and 0.3 V/µs slew rate, housed in an 8-SOIC package. It combines two independent amplifiers with internal frequency compensation and is qualified to AEC-Q100 specifications for automotive applications. An operational amplifier is a high-gain, differential-input analog amplifier that uses external feedback to set its closed-loop gain and signal behavior. Within the broader semiconductor hierarchy, this device belongs to the linear-amplifier family and ultimately to the amplifier-IC category. The LM2904 family is widely used for low-frequency signal conditioning because it combines reasonably high open-loop gain, broad supply-voltage capability, low supply-current consumption, and a conventional industry-standard pin arrangement. The most prominent operating characteristics are its 26 V maximum supply rating, 700 kHz gain-bandwidth product, and 0.3 V/µs slew rate. Each channel supports single-supply operation, while the two amplifiers can also be used with suitable bipolar supplies. The device is intended for general-purpose amplification and includes two circuits in one 8-SOIC package, reducing board area compared with separate single amplifiers. Its frequency-compensated architecture is suited to non-inverting, inverting, summing, comparator-like, and transducer-amplification stages operating within the device's bandwidth. The automotive qualification is important where operating-temperature robustness and controlled quality are required. Exact input-offset voltage, input-bias current, output-current capability, common-mode limits, and temperature limits must be confirmed in the manufacturer datasheet for the selected grade and package. Typical uses include low-level sensor conditioning, transducer amplifiers, DC gain stages, active filters, audio and communications interfaces, and automotive signal-processing modules. The two-amplifier configuration is particularly useful when a board needs two similar signal paths in one package, such as differential sensing or paired filter stages. Design with the 700 kHz bandwidth and 0.3 V/µs slew rate in mind. Keep input and feedback routing short, observe the supply and common-mode limits from the manufacturer datasheet, and verify output swing at the intended load. Decoupling capacitors should be placed close to the supply pins to reduce supply impedance and switching noise. This product page combines the exact ordering information, package details, qualified family information, verified drop-in candidates, and practical design considerations needed to plan an automotive dual-op-amp design before committing the LM2904AVQDRG4Q1 to a PCB.

RFQ Kontak
LM2904AVQDRQ1 - 26V 700kHz Dual Op Amp | Texas Instruments
LM2904AVQDRQ1

LM2904AVQDRQ1 - 26V 700kHz Dual Op Amp | Texas Instruments

The Texas Instruments LM2904AVQDRQ1 is an automotive-grade, dual operational amplifier rated for 26 V supply operation and 700 kHz gain-bandwidth performance, housed in an 8-pin SOIC package. The device contains two independent, general-purpose amplifiers with frequency compensation, making it suitable for signal conditioning, sensor amplification, and automotive electronic control systems. An operational amplifier, commonly abbreviated op amp, is an analog signal-processing IC that compares an input voltage with a feedback reference and drives its output to reduce the difference between them. A dual operational amplifier combines two amplifiers in one package, reducing board area and simplifying dual-channel or differential signal-chain designs. The LM2904-Q1 family extends the widely recognized LM2904 architecture with automotive qualification under AEC-Q100 requirements. The LM2904AVQDRQ1 provides a 26 V maximum supply rating, a 700 kHz gain-bandwidth product, and an operating temperature range of -40°C to +125°C. Its low-supply-current design supports power-constrained systems, while the high-voltage capability accommodates automotive and industrial transients when paired with appropriate protection. The device also includes ESD protection exceeding 500 V under MIL-STD-883, Method 3015 and exceeding 200 V using the machine model. Internally, the LM2904 family uses two independent, high-gain, frequency-compensated operational-amplifier channels. Internal compensation removes the need for an external frequency-compensation network in typical closed-loop gain configurations. This characteristic simplifies PCB design and supports common amplifier arrangements such as voltage followers, non-inverting gain stages, inverting amplifiers, comparators, and transducers with differential outputs. Typical applications include automotive sensor interfaces, low-side current measurement, pressure and temperature conditioning, battery monitoring, audio preamplification, and general-purpose control modules. Its dual-channel organization is particularly useful when a design needs one amplifier for signal conditioning and another for filtering, buffering, or an independent control function. Designers should verify the input common-mode range and output-swing limits against the actual supply voltage and signal range. The datasheet pin configuration should be used directly during PCB routing, particularly because the dual amplifier shares common supply pins. Input and output paths should also be kept away from switching-current loops to minimize coupled noise. This page combines manufacturer qualification details, a focused replacement comparison, and practical circuit-level guidance for engineers evaluating the LM2904AVQDRQ1 in automotive and industrial analog signal chains. The product is an operational amplifier, a linear amplifier, an analog IC, and a semiconductor device designed for voltage feedback and signal-conditioning applications.

RFQ Kontak
LM2904AVQPWR - Dual 30V 700kHz Op Amp | Texas Instruments
LM2904AVQPWR

LM2904AVQPWR - Dual 30V 700kHz Op Amp | Texas Instruments

The Texas Instruments LM2904AVQPWR is a dual, general-purpose operational amplifier in an 8-pin TSSOP package, with two independent, internally frequency-compensated amplifiers. The device supports a 30 V maximum total supply rating, delivers a typical gain-bandwidth product of 700 kHz, and operates across a -40°C to 125°C temperature range. Its two-amplifier configuration makes it suitable for signal conditioning, transducer amplification, and analog control circuits using single or split supplies. An operational amplifier is an analog building block that amplifies the voltage difference between its differential input while using negative feedback to set closed-loop gain and bandwidth. The LM2904 belongs to the broader hierarchy of linear amplifiers, analog signal-chain ICs, and semiconductor components. It is internally compensated, which simplifies implementation by removing the need for an external compensation capacitor in standard closed-loop configurations. Key characteristics include low supply-current drain, low input bias and offset currents, and an input common-mode range that extends close to ground for single-supply applications. The typical supply-current consumption is 0.7 mA per amplifier. Its broad supply range and temperature rating support industrial control, automotive, instrumentation, and test-equipment designs where the amplifier must operate across changing supply and ambient conditions. The LM2904 architecture uses two independent, high-gain, frequency-compensated amplifiers in one package. Internal compensation establishes the dominant pole and makes unity-gain operation practical without external compensation components. The 700 kHz gain-bandwidth product supports moderate-frequency signal conditioning rather than high-speed data acquisition, so layout should minimize feedback-loop area and keep sensitive input nodes away from supply and output routing. Typical uses include sensor-amplifier front ends, low-frequency active filters, comparator-style threshold circuits with saturation recovery, audio preamplifier stages, and programmable control interfaces. For automotive and industrial systems, the wide operating-temperature range and wide supply tolerance are especially useful, while the low input bias current helps preserve sensor accuracy. When designing around the LM2904AVQPWR, verify the input common-mode range against the actual signal and supply levels, particularly near the positive rail. Decoupling capacitors should be placed directly across the supply pins, and unused amplifier inputs must be biased rather than left floating. Avoid relying on the device for millivolt-level precision tasks without checking offset, drift, and bias-current contributions for the complete signal chain. This page consolidates package details, verified distributor pricing evidence, drop-in alternatives, and application-oriented design guidance for engineers evaluating the LM2904AVQPWR. It also distinguishes supply-voltage, temperature, channel-count, and bandwidth trade-offs among pin-compatible LM2904-family options.

RFQ Kontak
LM2904AVQPWRG4 - Dual 700kHz Op Amp | Texas Instruments
LM2904AVQPWRG4

LM2904AVQPWRG4 - Dual 700kHz Op Amp | Texas Instruments

Texas Instruments LM2904AVQPWRG4 is a dual general-purpose operational amplifier with a 700 kHz gain-bandwidth product, 26 V maximum total supply capability, and an 8-pin TSSOP package. Each amplifier channel provides input, output, and supply connections, allowing one package to implement two independent gain stages or a differential amplifier arrangement. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. The LM2904 belongs to the operational-amplifier hierarchy, where it serves as a general-purpose amplifier for signal conditioning, buffering, voltage amplification, and feedback-based control. Its common-mode input range includes ground, allowing direct sensing of signals near 0 V. The device operates from single or dual supplies. The manufacturer specifies operation from up to 26 V total for single-supply operation, or up to 13 V per rail for dual supplies. A typical supply-current drain of 0.7 mA is specified as independent of supply voltage. The two-amplifier configuration also supports independent operation of each channel rather than requiring both channels to perform the same function. The 700 kHz gain-bandwidth product supports general-purpose amplification at low and moderate frequencies rather than high-speed signal conditioning. Because this is not a rail-to-rail input or output device, the input and output operating regions must remain within the amplifier’s supply-dependent limits. Bias and offset requirements should be checked against the circuit’s signal amplitude and source impedance. Typical applications include low-frequency sensor conditioning, analog signal buffering, feedback control, audio preamplification, and general instrumentation. The TSSOP package supports compact surface-mount layouts, while the dual channel count reduces component count when two gain stages are needed. In a single-supply system, the input common-mode range extending to ground is especially useful for signals produced by sensors near the lower supply rail. When laying out the circuit, keep feedback components and input sources close to the appropriate pins, maintain a common ground reference, and decouple the supply connection. Avoid relying on the amplifier for isolation or level translation outside its specified input and output ranges. Stability with capacitive loads should be evaluated because capacitive loading can alter the effective gain-bandwidth response and introduce peaking. This product page combines the manufacturer’s electrical characteristics with package, sourcing, replacement, and application guidance. It also identifies the differences between verified same-brand family alternatives and highlights the electrical checks required before treating any substitute as a true drop-in replacement.

RFQ Kontak
LM2904AVQPWRG4Q1 - Dual 26V 700kHz AEC-Q100 Op Amp | TI
LM2904AVQPWRG4Q1

LM2904AVQPWRG4Q1 - Dual 26V 700kHz AEC-Q100 Op Amp | TI

The Texas Instruments LM2904AVQPWRG4Q1 is a dual, general-purpose operational amplifier with a 26 V maximum supply rating, 700 kHz gain-bandwidth product, and AEC-Q100 automotive qualification. The device is offered in an 8-pin TSSOP package and supports single-supply or dual-supply operation, making it suitable for automotive, industrial, and low-cost analog signal-conditioning circuits. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The dual configuration provides two independent amplifiers in one package, which saves board area in applications such as sensing, filtering, buffering, and control loops. Within the device hierarchy, this part belongs to the operational amplifier family of amplifier ICs, combining wide supply-voltage tolerance with low supply-current consumption. Key characteristics include a 700 kHz gain-bandwidth product, an input common-mode range that includes ground, and a low typical supply-current drain of 0.7 mA. The common-mode capability supports direct sensing near ground in battery-powered and sensor-interface circuits. Single-supply operation is possible because the common-mode input range reaches the negative supply rail, while the 26 V rating supports higher-voltage industrial control systems. The LM2904 architecture uses frequency compensation to provide stable closed-loop operation in typical amplifier configurations. Its wide supply range and low supply-current drain suit applications that need adequate signal headroom without continuous high quiescent power. Automotive qualification is provided under AEC-Q100 specifications for the LM2904-Q1 family. Typical uses include 12 V automotive sensor conditioning, low-side current measurement, transducer amplification, active filtering, and general-purpose analog control. The TSSOP-8 outline also supports compact mixed-signal boards where a dual amplifier is needed rather than two separate single-channel devices. Design with adequate supply decoupling, confirm the input common-mode and output-swing limits against the actual signal range, and check the maximum total supply voltage before applying power. This page also organizes pinout, packaging, qualification, drop-in alternatives, and application guidance for faster component selection.

RFQ Kontak
LM2904AVQPWRQ1 - 26V, 700kHz Automotive Dual Op Amp | TI
LM2904AVQPWRQ1

LM2904AVQPWRQ1 - 26V, 700kHz Automotive Dual Op Amp | TI

Texas Instruments LM2904AVQPWRQ1 is an automotive-grade, dual operational amplifier with a 26 V maximum supply rating, 700 kHz gain-bandwidth product, and an 8-pin TSSOP (PW) package. The device contains two independent, high-gain, frequency-compensated amplifiers and is qualified to AEC-Q100 specifications for automotive applications. An operational amplifier is an analog IC that provides high open-loop gain and signal amplification for sensors, control loops, filters, and signal-conditioning circuits. The LM2904-Q1 family belongs to the operational amplifier hierarchy, where each amplifier section provides voltage amplification, impedance buffering, and feedback-based signal conditioning within a wider analog or mixed-signal system. Key characteristics include two amplifier circuits, a 700 kHz gain-bandwidth product, a 0.3 V/µs slew rate, a typical input offset voltage of 3 mV, and typical input bias current of 20 nA. The operating temperature range extends from -40°C to +125°C, supporting industrial and automotive environments where temperature and qualification requirements exceed those of ordinary general-purpose amplifiers. The internally compensated architecture simplifies implementation of standard inverting, non-inverting, summing, and feedback amplifier circuits. A typical supply current is 500 µA per channel, while output current capability reaches 40 mA per channel. These characteristics make the device suitable for low-power analog signal conditioning where a 3 V minimum supply is required and the circuit must tolerate supply voltages up to 26 V. Typical uses include sensor interfaces, actuator drivers, motor-control feedback networks, battery-powered instrumentation, industrial control loops, and automotive signal-conditioning modules. The wide supply range allows operation from single or split supplies, although the differential voltage between the supply rails must remain within the device limits. Designers should verify output swing, input common-mode range, stability, and load capability across the complete supply and temperature range. Decoupling capacitors should be placed close to the supply pins, while feedback components and sensitive input routes should be kept away from switching nodes to reduce coupling and maintain low offset performance.

RFQ Kontak
LM2904AWYPT - Dual Low-Power Op Amp, 8-TSSOP | STMicroelectronics
LM2904AWYPT

LM2904AWYPT - Dual Low-Power Op Amp, 8-TSSOP | STMicroelectronics

The STMicroelectronics LM2904AWYPT is a low-power dual operational amplifier with two independent, internally frequency-compensated amplifiers in an 8-pin TSSOP package. The device is identified for ±15 V / 30 V automotive applications and is associated with AEC-Q100 qualification in distributor listings. Its dual-amplifier configuration makes it suitable for signal conditioning, voltage buffering, instrumentation, and general-purpose analog circuits where two amplifier channels are required in one compact package. An operational amplifier is a voltage-controlled, high-gain analog building block used to amplify, buffer, filter, or compare small electrical signals. The LM2904 belongs to the dual general-purpose operational-amplifier family, combining two amplifier sections with internal frequency compensation in a single surface-mount IC. This type of device sits within the broader analog IC and semiconductor hierarchy and is commonly used between sensors, transducers, reference circuits, and downstream measurement or control stages. Key features include two amplifier circuits in one package, low-power operation, internal frequency compensation, and an 8-pin TSSOP surface-mount form factor. The automotive identification is useful when the application requires an AEC-Q100-qualified device, although the exact temperature range, supply limits, input and output characteristics, slew rate, and common-mode performance should be confirmed against the STMicroelectronics datasheet for the exact order code. The package also supports compact PCB layouts where two amplifier channels must be placed close together. The internal compensation allows the amplifier sections to operate without external frequency-compensation components in typical closed-loop configurations. That simplifies analog design and reduces the number of external components in feedback networks. Because the product is a dual amplifier, both channels have their own inputs and outputs, enabling common tasks such as differential sensing, active filtering, or complementary signal processing within one package. The manufacturer product page describes the device as two independent, high-gain operational amplifiers with internally implemented frequency compensation. Typical applications include automotive sensor interfaces, industrial control modules, low-power signal-conditioning boards, battery-powered instruments, audio preamplifier stages, and general-purpose analog front ends. In an instrumentation application, one channel could amplify a sensor signal while the other handles buffering or an active-filter function. In a vehicle electronics module, the dual amplifier can reduce the number of discrete analog ICs while supporting a compact, surface-mount assembly. The principal design consideration is to verify the exact electrical limits and recommended operating conditions before finalizing the power rails, input common-mode range, output swing, and external feedback network. Decoupling capacitors should be placed close to the supply pins, and the PCB layout should minimize parasitic capacitance and resistance on feedback and input nodes. The TSSOP package is small, so adequate copper and solder-joint quality remain important for reliable assembly. This page combines manufacturer identification, distributor listings, cross-reference information, drop-in alternatives, and engineering-oriented design guidance for engineers evaluating LM2904AWYPT. It focuses on the distinctions that affect PCB compatibility, supply planning, signal conditioning, and automotive qualification rather than repeating only the basic catalog description.

RFQ Kontak
LM2904AYDT - Dual 1.1MHz Op Amp | STMicroelectronics
LM2904AYDT

LM2904AYDT - Dual 1.1MHz Op Amp | STMicroelectronics

The STMicroelectronics LM2904AYDT is a dual general-purpose operational amplifier with two independent, internally frequency-compensated amplifiers, a 1.1 MHz gain-bandwidth product, 0.6 V/us slew rate, and 20 nA input bias current. The device operates from a single positive supply and is packaged in an 8-pin SOIC for automotive and industrial control systems. An operational amplifier is an analog signal-conditioning device that compares an inverting input with a non-inverting input and amplifies the voltage difference between them. The dual-amplifier configuration places two independent amplifiers in one package, allowing one IC to implement two signal paths. Within the broader semiconductor hierarchy, an operational amplifier belongs to the linear amplifier family and supports closed-loop gain, filtering, buffering, current-to-voltage conversion, and feedback-control applications. The LM2904AYDT provides two independent channels, 1.1 MHz gain-bandwidth product, 0.6 V/us slew rate, and 20 nA input bias current. Its internally compensated architecture simplifies typical closed-loop amplifier use without an external frequency-compensation network. The low input bias current is useful when the amplifier must operate with relatively high source impedance, while the 1.1 MHz bandwidth supports general-purpose signal amplification at low and moderate frequencies. The circuit is designed specifically for automotive and industrial control systems and operates from a single power supply over a wide voltage range. Both channels are independent, so they can process separate signals and do not share internal signal paths. The SOIC-8 package offers a compact surface-mount format compatible with conventional PCB assembly, while the automotive-oriented ordering code identifies the manufacturer’s grade and delivery configuration. Typical uses include low-frequency sensor conditioning, industrial control-loop amplifiers, transducers with relatively high source impedance, buffer stages, and general signal-conditioning modules. Two channels can be used for a differential stage, a voltage follower and an active filter, or two independent control channels. The device is best suited to general-purpose precision amplification rather than high-speed, high-voltage, or low-noise applications requiring specialized amplifier families. When laying out a PCB, keep input and feedback traces short, route them away from switching nodes, and provide a stable ground reference. Decouple each supply rail close to the device with suitable ceramic capacitance and avoid placing long output traces beside high-current digital paths. Because the SOIC-8 leads are closely spaced, inspect assembly clearances and ensure adequate copper and soldermask isolation under the package. This page combines the manufacturer’s functional description with package, qualification, lifecycle, sourcing, and cross-reference information. It also provides application-focused engineering guidance and a parameter comparison table so engineers can evaluate the LM2904AYDT against other compatible SOIC-8 dual operational amplifiers before committing a design.

RFQ Kontak
LM2904AYPT - Dual Low-Power Op-Amp, 1.1MHz | STMicroelectronics
LM2904AYPT

LM2904AYPT - Dual Low-Power Op-Amp, 1.1MHz | STMicroelectronics

The STMicroelectronics LM2904AYPT is a low-power dual operational amplifier with two independent general-purpose amplifier circuits, a 1.1 MHz gain-bandwidth product, a 0.6 V/us slew rate, and operation from a single supply of 3 V to 30 V, housed in an 8-pin TSSOP package. The A suffix and Y suffix identify the automotive-grade version, which STMicroelectronics qualifies for harsh automotive and industrial environments with extended temperature capability. An operational amplifier (op-amp) is an analog building block that amplifies the voltage difference between its two inputs with very high open-loop gain. As a member of the operational amplifier hierarchy, the LM2904 family sits under linear amplifiers, then amplifier ICs, then analog integrated circuits. Dual op-amps such as the LM2904A integrate two matched amplifiers in one package, saving board area and improving channel matching in multi-stage analog signal chains. Key features include an input offset voltage of typically 2 mV (maximum 7 mV per the LM2904A grade), an input bias current of 20 nA, a large common-mode input range that extends to the negative rail, and single-supply operation down to 3 V. A power drain of only 0.7 mA per amplifier (typical) makes the part suitable for battery-powered and always-on circuits. Output current capability of approximately 20 mA per channel drives moderate loads directly. The bipolar process technology used in the LM2904A provides rugged, well-understood behavior: graceful performance degradation near the rails, low 1/f-noise characteristics typical of bipolar input stages, and a unity-gain stable configuration requiring no external compensation capacitor. The internal 100 dB-class DC open-loop gain and good channel-to-channel matching support precision comparator, amplifier, and filter topologies. Typical applications include automotive sensor signal conditioning (oxygen sensors, position sensors), battery monitors and current-sense amplifiers in 12 V and 24 V vehicle systems, industrial transducer front ends, active filters, comparators with hysteresis, and low-speed signal buffering in HVAC and appliance controllers. When designing with the LM2904AYPT, remember that the output cannot swing fully to the positive rail and that phase reversal is avoided on the inverting input only within the specified common-mode range; keep gain-setting resistors above 10 kohm to limit bias-current error, and place a 100 nF decoupling capacitor within 5 mm of pin 8. This page adds value beyond the manufacturer datasheet by combining drop-in alternative comparisons, application-specific design notes, parametric comparison tables, and sourcing guidance in one place.

RFQ Kontak
LM2904BAIDR - Dual 36V 1.2MHz Op Amp | Texas Instruments
LM2904BAIDR

LM2904BAIDR - Dual 36V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM2904BAIDR is a dual, general-purpose operational amplifier optimized for operation from a 3 V to 36 V supply in an 8-pin SOIC package. Each amplifier channel offers a gain bandwidth product of 1.2 MHz and an input offset voltage of up to 2 mV. The device is designed for general-purpose signal conditioning across industrial, instrumentation, audio, communications, and control applications where a wide supply-voltage range and two amplifiers per package simplify board allocation. An operational amplifier is an analog signal-processing IC that amplifies the voltage difference between its inverting and non-inverting inputs. Within the broader hierarchy, an operational amplifier belongs to the amplifier IC family and ultimately serves as a building block in analog, mixed-signal, and control systems. Unlike a discrete transistor stage, a dual operational amplifier integrates gain stages, biasing, compensation, output drivers, and protection functions into one package. The LM2904BAIDR provides two independent amplifier channels, a 1.2 MHz gain bandwidth product, and offset voltage specified to 2 mV. Its 36 V maximum supply rating provides additional operating headroom for industrial systems and laboratory equipment. The operating temperature range extends from -40°C to 125°C, supporting applications across commercial and industrial temperature environments. The 8-pin SOIC footprint also supports conventional surface-mount assembly and hand-soldering workflows. Texas Instruments positions the LM2904B family as an upgraded functional relative to the original LM2904 family. The LM2904B page identifies a 36 V maximum supply voltage and 1.2 MHz gain bandwidth product, while the original LM2904 page identifies a 26 V maximum supply voltage and 700 kHz gain bandwidth product. This generational increase provides more bandwidth and supply-voltage headroom without changing the familiar dual-amplifier architecture. Typical uses include low-frequency instrumentation, industrial sensor interfaces, audio preamplification, communications equipment, active filtering, comparators, and general DC signal amplification. Two channels can implement differential, summing, feedback, or multi-stage amplifier arrangements. The 1.2 MHz bandwidth makes the device most appropriate for signals well below the upper practical frequency range of this general-purpose amplifier family. Designers should verify the input common-mode range, output swing, input bias current, noise, and load capability against their actual operating conditions. Decoupling capacitors should be placed close to the supply pins, and sensitive analog inputs should be routed away from switching nodes. The two amplifier outputs should not be tied together unless the application explicitly supports a particular parallel-output configuration. This page combines the LM2904BAIDR ordering information, principal electrical ratings, lifecycle context, and family-level replacement guidance. It also identifies same-package alternatives and explains when the original LM2904, the enhanced LM2904B, or the specifically ordered BA suffix best matches a design requirement.

RFQ Kontak
LM2904BIDGKR - Dual 36V 1.2MHz Op Amp | Texas Instruments
LM2904BIDGKR

LM2904BIDGKR - Dual 36V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM2904BIDGKR is a dual general-purpose operational amplifier with a 36 V maximum supply rating, a 1.2 MHz gain-bandwidth product, and a 0.5 V/us slew rate. The device is supplied in an 8-pin VSSOP (DGK) package and is specified for operation from -40C to +125C. An operational amplifier is an analog signal-conditioning IC that amplifies the voltage difference between its inverting and non-inverting inputs. The dual architecture provides two independent amplifiers in one package, making the LM2904B suitable for signal conditioning, current monitoring, filtering, and general feedback-control circuits. Its position in the signal-chain hierarchy is operational amplifier, analog amplifier, analog integrated circuit, and semiconductor. The LM2904B version provides a 3 V to 36 V operating supply range, a 1.2 MHz gain-bandwidth product, and a 0.5 V/us slew rate. The improved LM2904B family also features enhanced ESD protection relative to the original LM2904 family. These characteristics make it suitable for industrial control systems and other applications operating from industrial supply rails. Two independent amplifier channels are provided in a compact 8-pin surface-mount package. The wide supply range allows operation from a single low-voltage rail or from split positive and negative supplies when the circuit requires them. The device is intended for general-purpose applications rather than precision instrumentation, where very low offset voltage and very low bias current would be required. Typical uses include transducer and sensor signal conditioning, low-frequency active filters, audio and communications interface circuits, voltage monitoring, and process-control loops. Industrial instrumentation is a natural fit because the specified operating temperature reaches 125C. The 1.2 MHz bandwidth supports lower-frequency precision and control tasks rather than high-speed video or RF applications. When designing the circuit, verify input and output common-mode limits at the selected supply voltage and provide adequate output-current headroom for the load and feedback network. Decoupling capacitors should be placed close to the supply pins, and the unused amplifier channel should be configured with inputs tied to a valid common-mode voltage rather than left floating. This page consolidates package, temperature, electrical-performance, and cross-reference information into an engineering-focused selection guide. It also documents verified drop-in relationships, practical layout guidance, application use cases, and parameter-level comparisons that help shorten design evaluation time.

RFQ Kontak
LM2904BIDR - Dual 36V 1.2MHz Op Amp | SOIC-10 | TI
LM2904BIDR

LM2904BIDR - Dual 36V 1.2MHz Op Amp | SOIC-10 | TI

The Texas Instruments LM2904BIDR is an industry-standard dual operational amplifier in an 8-pin SOIC package, delivering 1.2 MHz unity-gain bandwidth and a wide 3 V to 36 V supply range with single-supply operation. It is the next-generation 'B' revision of the legacy LM2904, providing tighter DC accuracy (lower input offset voltage), lower noise, and a 1.2 MHz bandwidth upgrade versus the original 700 kHz device, while remaining in the industry-standard 8-pin SOIC footprint used by all LM358 / LM2904 variants. Each channel is a bipolar voltage-frontier amplifier with internal EMI/RFI filtering and ESD protection on the inputs, and the device operates over the automotive -40C to +125C temperature range. An operational amplifier (op amp) is a high-gain DC-coupled differential amplifier whose output voltage is amplified by an external feedback network to perform amplification, filtering, and signal conditioning. A dual op amp integrates two ICs into a single package and is the same circuit-level topology (LDO) integrated with a higher-level power-supply chain and ultimately a semiconductor device, while dual op amps specifically serve as a low-side companion building block used in many sensor, instrumentation, and power-management signal chains. Key features include 1.2 MHz gain-bandwidth product, 0.5 mV typical (3 mV maximum) input offset voltage, 45 V/us (typical) slew rate, 25 nA input bias current, and an output swing that includes both rails. The device operates on a single supply from 3 V up to 36 V (or dual +/-1.5 V to +/-18 V). It is internally compensated for unity-gain stability and includes short-circuit protection on the output, making it suitable for direct drive of low-impedance loads in industrial and automotive environments. The LM2904BIDR uses a bipolar process with a PNP input stage that supports input common-mode voltages down to ground (and up to VCC - 1.5 V), enabling true single-supply operation from a 5 V or 12 V rail. The dual-channel architecture allows one IC to implement two independent gain stages - commonly a transimpedance amplifier and a buffer, or two channels of a differential sensor front-end - saving PCB area, cost, and complexity versus using two single-channel op amps. Typical applications include transducer interfaces (load cells, strain gauges, pressure and flow sensors), low-side current sensing in motor drives and battery management, active filters and integrators for instrumentation, comparator-like threshold detection, and general-purpose signal conditioning on 12 V / 24 V industrial and automotive buses. The wide supply range and automotive-grade temperature rating make it drop-in compatible with virtually every legacy LM288 / LM358 / LM2904 design. When designing with this device, ensure the input common-mode voltage remains within the linear range (GND to VCC - 1.5 V). For single-supply designs, AC-couple the input or bias the network to mid-supply. Decouple the supply pin with a 1 uF / 100 nF parallel pair within 10 mm of the IC, and avoid driving capacitive loads greater than 1 nF directly - add a series isolation resistor if needed. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving you a complete engineering perspective in one page.

RFQ Kontak
LM2904BQDRQ1 - Dual 36V 1.2MHz Op Amp | Texas Instruments
LM2904BQDRQ1

LM2904BQDRQ1 - Dual 36V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM2904BQDRQ1 is an automotive-grade, dual operational amplifier with a 36 V supply rating, 1.2 MHz gain-bandwidth performance, and operation from -40°C to 125°C, housed in an 8-pin SOIC package. It combines two independent general-purpose amplifiers, making it suitable for signal conditioning, filtering, sensing, and feedback-control circuits operating from low-voltage to higher-voltage industrial and vehicle systems. An operational amplifier is a voltage-feedback amplifier that uses high open-loop gain to amplify the difference between its inverting and non-inverting inputs. The LM2904B-Q1 belongs to the broader operational-amplifier, analog-signal-conditioning, and semiconductor hierarchy. Its two amplifier channels can process independent signals or work together as a differential amplifier, buffer, comparator-style circuit, or active-filter stage when supported by the surrounding network. The principal feature set includes two amplifier circuits, a 36 V maximum supply rating, a 1.2 MHz gain-bandwidth product, and an operating-temperature range of -40°C to 125°C. The automotive-grade ordering option is designed for applications that require operation across an extended industrial temperature range. The standard general-purpose amplifier designation also indicates that the device is intended for a broad range of conventional analog signal-processing tasks rather than one narrowly defined precision function. In each channel, feedback determines closed-loop gain and bandwidth. Negative feedback stabilizes gain, reduces distortion, and improves linearity, while positive or open-loop use can support comparator-style functions when the system design requires saturation behavior rather than linear amplification. Because the device operates from a relatively wide supply range, designers must check input- and output-voltage limits, input common-mode range, output swing, and power dissipation against the actual rail voltages rather than relying only on the 36 V maximum rating. Typical applications include automotive sensor interfaces, industrial control and instrumentation, low-side current measurement, transducer amplification, analog filtering, audio and communication signal conditioning, and general feedback-control loops. In each case, the two channels can reduce component count when the circuit requires one signal-processing path and one feedback or auxiliary path on the same package footprint. A careful design should verify the input common-mode range, output-voltage swing, unity-gain stability, noise performance, and maximum output current against the selected gain and load. Input and output stability networks, grounding, and decoupling also require attention because excessive capacitive loading or incorrect source impedance can alter stability and transient response. The 8-pin SOIC footprint is suitable for conventional surface-mount assembly, although exposed-pad thermal considerations do not apply to this package. This product record combines manufacturer specifications, automotive qualification information, package details, application guidance, and constrained drop-in alternatives. It also highlights where engineers should compare speed, supply range, common-mode limits, and automotive requirements before changing the amplifier in an existing circuit.

RFQ Kontak
LM2904BQPWRQ1 - 36V 1.2MHz Dual Op Amp | Texas Instruments
LM2904BQPWRQ1

LM2904BQPWRQ1 - 36V 1.2MHz Dual Op Amp | Texas Instruments

The Texas Instruments LM2904BQPWRQ1 is an automotive-grade, dual operational amplifier designed for single-supply operation up to 36 V, with a gain-bandwidth product of 1.2 MHz. The device is packaged in an 8-pin TSSOP package and operates across the -40°C to 125°C temperature range. It provides two amplifiers in one package, making it suitable for industrial, automotive, and instrumentation signal-conditioning systems. An operational amplifier is a voltage-controlled, high-gain analog building block used to amplify differential signals, buffer sensors, perform active filtering, and drive analog-to-digital converter inputs. Within the power-management and signal-processing hierarchy, the LM2904B-Q1 is a general-purpose bipolar operational amplifier designed to provide stable operation with relatively simple external compensation and conventional power-supply connections. The LM2904BQPWRQ1 combines a 1.2 MHz gain-bandwidth product with a 36 V maximum supply rating. Its automotive qualification according to AEC-Q100 makes it appropriate for harsh operating environments where temperature range and product qualification are important. The dual configuration reduces package count when two independent amplifier channels are required, while its 8-pin TSSOP format supports compact surface-mount PCB construction. The architecture is suited to signal paths operating from low-level sensor outputs through intermediate analog levels. A wide supply-voltage range allows the same amplifier family to work with conventional industrial rails, while the 1.2 MHz gain-bandwidth product provides useful bandwidth for audio-frequency and general instrumentation applications. Exact input-offset, input-bias, output-swing, and slew-rate limits should be confirmed against the manufacturer datasheet for the operating conditions used in the final design. Typical applications include automotive sensor conditioning, low-voltage signal buffering, active analog filters, transducer interfaces, audio amplification stages, and general-purpose control-system analog inputs. The dual amplifier configuration is especially useful when a board requires matched channels for two sensors or when a second channel is used for reference buffering or gain compensation. Layout should keep feedback components close to the corresponding amplifier inputs and provide a low-impedance return path for the supply and ground pins. Decoupling capacitors should be positioned near the package power terminals, while sensitive input traces should remain away from switching nodes and high-current return paths. Stable operation also depends on observing the input common-mode and output-swing limits in the manufacturer datasheet. This page combines application guidance, design considerations, parameter comparisons, and focused replacement options for engineers evaluating the LM2904BQPWRQ1 across automotive, industrial, and instrumentation signal-conditioning designs.

RFQ Kontak
LM2904DE4 - Dual 26V 700kHz Op Amp | Texas Instruments
LM2904DE4

LM2904DE4 - Dual 26V 700kHz Op Amp | Texas Instruments

Texas Instruments LM2904DE4 is a dual, general-purpose operational amplifier with a maximum supply rating of 26 V, a 700 kHz gain-bandwidth product, and a 0.3 V/µs slew rate. The device is supplied in an 8-pin SOIC package and provides two amplifier channels in one package. Its 0.7 mA typical supply-current draw supports low-power signal-processing systems. An operational amplifier is an analog amplifier that uses high open-loop gain and negative feedback to amplify voltage differences. Within the semiconductor hierarchy, an operational amplifier belongs to the amplifier IC and signal-conditioning category. The LM2904 combines two general-purpose amplifier channels in a single package, reducing board area when a design requires matched dual-channel functions such as filtering, buffering, or gain stages. The LM2904DE4 provides a 700 kHz gain-bandwidth product, a 0.3 V/µs slew rate, and a low 0.7 mA typical supply-current drain independent of supply voltage. Its common-mode input range includes ground, making it useful in circuits that operate near the lower supply rail. The dual configuration supports applications in industrial controls, sensor interfaces, audio paths, and general-purpose analog signal conditioning. The 26 V maximum supply rating provides ample headroom for conventional industrial supply rails, although the actual operating voltage must remain within the manufacturer’s specified limits. Because this is a general-purpose amplifier rather than a precision part, design engineers should verify input offset, input bias current, output swing, and channel behavior against the application’s signal-integrity requirements. Feedback-network components and signal-source impedances determine practical accuracy and stability. Typical uses include two-stage sensor amplification, low-frequency active filters, buffered instrument inputs, audio preamplification, and general industrial signal conditioning. The 8-pin SOIC package is also compatible with conventional surface-mount assembly and automated PCB manufacturing. The dual organization allows one package to implement complementary signal paths while reducing component count compared with two separate single amplifiers. For stable operation, follow the manufacturer’s recommended compensation and decoupling practices, place input and output networks close to the device, and avoid driving the output beyond its specified load and swing limits. Grounding and trace-return paths should be planned to prevent supply and ground noise from entering the signal path. The manufacturer datasheet is the controlling reference for electrical limits, pin functions, and application details. This product page combines the official family specifications with practical design guidance, application fit analysis, and a package-focused replacement comparison. It is intended to help engineers identify the correct operating limits and select a pin-compatible alternative without overlooking differences in bandwidth, slew rate, supply current, or package construction.

RFQ Kontak
LM2904DG - Dual 1MHz Op Amp, 3-32V | onsemi
LM2904DG

LM2904DG - Dual 1MHz Op Amp, 3-32V | onsemi

onsemi LM2904DG is a dual, general-purpose operational amplifier with two independent amplifiers, 1 MHz gain-bandwidth product, 0.6 V/us slew rate, and a 3 V to 32 V supply range in an 8-pin SOIC package. It supports single-supply or split-supply operation and accepts input common-mode voltages extending to ground and VEE. An operational amplifier is a voltage-controlled differential amplifier used to amplify, buffer, filter, compare, or drive analog signals. The LM2904 belongs to the broader operational-amplifier hierarchy, where the dual configuration provides two signal-processing channels in one package. This makes it useful where board area, component count, and supply flexibility are more important than precision or high speed. Key features include a 1 MHz gain-bandwidth product, 0.6 V/us slew rate, and a minimum common-mode rejection ratio of 50 dB. The device is specified for a 3 V to 32 V total supply, allowing operation from a single positive rail or from positive and negative rails. Its common-mode input range extends to ground and VEE, which supports battery-powered, industrial-control, and sensor-interface designs where input signals may approach the lower supply rail. The input offset voltage is listed at 7 mV, making this amplifier more appropriate for general-purpose amplification than precision instrumentation applications requiring microvolt-level offset. Its moderate gain-bandwidth product and slew rate are appropriate for audio-frequency control loops, slow sensor signals, active filtering, comparators, and general analog signal conditioning. The dual architecture also allows both amplifiers to share the same supply and decoupling network. Typical uses include DC motor and actuator feedback control, transducer buffering, low-frequency active filters, audio preamplification, regulated power-supply feedback, and general-purpose analog interfaces. Split-supply operation can simplify biasing around ground, while single-supply operation helps reduce system power and board complexity in battery-operated equipment. Designers should account for input bias current, output-current capability, common-mode limits, and stability when driving capacitive loads. Place decoupling capacitors close to the supply pins, keep feedback routing compact, and verify output swing against the actual load. For applications requiring very low offset, very wide bandwidth, rail-to-rail output, or automotive qualification, compare the LM2904 family against more specialized amplifier families. This product page combines manufacturer-datasheet characteristics, verified distributor listings, drop-in replacement analysis, application guidance, and package-level design notes to support faster component evaluation and PCB reuse decisions.

RFQ Kontak
LM2904DG4 - Dual 26V 700kHz Op Amp | Texas Instruments
LM2904DG4

LM2904DG4 - Dual 26V 700kHz Op Amp | Texas Instruments

Texas Instruments LM2904DG4 is a dual general-purpose operational amplifier with two independent amplifiers, a 26 V maximum supply rating, a 700 kHz gain-bandwidth product, and an 8-pin SOIC package. Each amplifier supports single-supply operation up to 26 V or dual-supply operation up to ±13 V, while the 0.7 mA typical supply-current drain remains independent of supply voltage. An operational amplifier is an analog signal-processing IC that amplifies the voltage difference between its non-inverting and inverting inputs. The LM2904 belongs to the operational-amplifier hierarchy, combining high open-loop voltage gain with negative feedback to set closed-loop behavior. Its two independent channels make it useful wherever two separate analog signals must be conditioned within the same package. Key characteristics include a 700 kHz gain-bandwidth product, a 0.3 V/µs slew rate, and a 0.7 mA typical supply-current drain. The common-mode input range includes ground, allowing single-supply systems to accept input signals near the lower supply rail. These characteristics support cost-sensitive general-purpose designs rather than precision or high-speed instrumentation. Internally, the LM2904 uses a conventional bipolar operational-amplifier architecture, with two independent amplifier channels and an eight-pin SOIC package. The 700 kHz gain-bandwidth product permits useful closed-loop bandwidth at moderate gain, while the 0.3 V/µs slew rate defines how quickly the output can move under large-signal conditions. Its low, supply-independent current draw helps maintain system efficiency. Typical uses include signal conditioning in industrial control systems, feedback and drive networks in power-conversion products, audio preamplifier stages, sensor interfaces, and general dual-amplifier modules. The tube packaging identified for LM2904DG4 is particularly appropriate for production assembly processes that use tube-fed through-hole or tube-to-tape conversion equipment. When designing around the LM2904DG4, verify input and output common-mode limits at the selected supply voltage, provide adequate bypassing close to the supply pins, and confirm that the required signal bandwidth and output swing remain within the amplifier's operating limits. Stable operation also depends on appropriate feedback compensation for the selected gain and load. This product page combines manufacturer specifications, package and pin information, engineering application guidance, and a structured comparison with compatible LM2904-family devices. It is designed to accelerate component selection and PCB planning while keeping the key trade-offs explicit.

RFQ Kontak
LM2904DGKR - Dual 26V 700kHz Op Amp | Texas Instruments
LM2904DGKR

LM2904DGKR - Dual 26V 700kHz Op Amp | Texas Instruments

The Texas Instruments LM2904DGKR is a dual general-purpose operational amplifier rated for a 26 V maximum supply, with a gain-bandwidth product of 700 kHz, packaged in an 8-pin VSSOP. The device contains two independent amplifiers, push-pull output stages, and support for single-supply or split-supply operation, making it suitable for cost-sensitive industrial, instrumentation, control, and signal-conditioning systems. An operational amplifier is a voltage-amplifying component that uses high open-loop gain and negative feedback to create accurate, stable analog signal paths. The dual-amplifier configuration reduces component count where two independent channels are required. Within the broader hierarchy of an operational amplifier, amplifier IC, analog IC, and semiconductor, the LM2904 occupies the general-purpose segment rather than a precision or high-speed specialty category. The LM2904 family provides low input offset voltage, a common-mode input range that extends to ground, and high differential input-voltage capability. The TI product page identifies the LM2904 as a dual, 26 V, 700 kHz operational amplifier, while the LM2904B family adds upgraded functionality and 36 V high-voltage operation. The LM2904DGKR ordering code specifically identifies the 8-pin VSSOP configuration, supporting compact surface-mount construction. Each channel is frequency compensated for closed-loop gain of 10 or more. The internal compensation enables straightforward implementation of non-inverting and inverting amplifiers, voltage followers, comparators, summing circuits, and basic active filters. Because the two amplifiers are independent, they can process different analog signals, although common power and ground pins share the total package current and thermal limitations. Typical uses include industrial sensor interfaces, low-frequency control loops, transducers, audio preamplification, battery-powered monitoring, test equipment, and general-purpose power-supply feedback. The VSSOP footprint is useful when a conventional 8-pin SOIC would occupy excessive board area. Designers should still evaluate input common-mode range, output swing, supply voltage, stability, and noise at the intended operating point. For reliable layout, place the bypass capacitor at the supply pins and maintain a short return path to the ground pins. Avoid long input traces that can acquire noise, especially when the LM2904 is used with high-impedance sources. Check output-current limits when driving a load, and verify that the selected gain, feedback values, and capacitive loading remain compatible with the device’s frequency-compensated architecture. This page combines manufacturer specifications, package and sourcing information, compatible replacement options, comparison parameters, and practical layout guidance to support component selection and PCB implementation for the LM2904DGKR.

RFQ Kontak
LM2904DGKRG4 Dual 26V 700kHz Op Amp | Texas Instruments
LM2904DGKRG4

LM2904DGKRG4 Dual 26V 700kHz Op Amp | Texas Instruments

Texas Instruments LM2904DGKRG4 is a dual general-purpose operational amplifier with a 26 V maximum supply rating, 700 kHz gain-bandwidth product, and two push-pull output stages in an 8-pin VSSOP package. The device combines two independent amplifiers with internal frequency compensation, making it suitable for signal conditioning, buffering, and general analog-control applications. An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. The LM2904 family belongs to the operational-amplifier hierarchy within analog and mixed-signal semiconductors. Its dual-channel architecture provides two amplifiers in one package, reducing board area when a design requires two similar signal paths. Each amplifier supports a 0.3 V/us slew rate, while the family's typical input offset voltage is 3 mV and typical input bias current is 20 nA. The typical supply current is 1 mA, making the LM2904 suitable for low-power instrumentation and embedded analog systems. Push-pull outputs support bidirectional output swings and improve drive capability compared with an open-collector output arrangement. The LM2904 is internally frequency compensated and intended for general-purpose operation rather than high-speed signal processing. Its 700 kHz gain-bandwidth product is adequate for audio-frequency instrumentation, feedback-control loops, sensor interfaces, and low-bandwidth active filters. The 26 V supply rating provides additional input-voltage headroom in industrial systems while retaining a conventional low-power implementation. Typical uses include buffering sensor outputs, amplifying low-level transducer signals, sampling circuits, active filtering, and general feedback-control loops. The dual configuration is particularly useful when a board needs matched signal conditioning for two channels or when a single package can provide two independent amplifier sections. When designing the circuit, check input common-mode and differential voltage limits against the actual signal range. Keep feedback components close to the amplifier pins, provide stable bypassing at the supply connection, and verify output swing against the load and rail conditions. The VSSOP footprint also benefits from short, direct return paths to reduce parasitic feedback. This page combines device specifications, application guidance, package information, and a parameter-by-parameter replacement comparison. It is intended to help engineers determine whether the LM2904DGKRG4 fits a circuit before releasing a board design or requesting production quotation.

RFQ Kontak
LM2904DMR2G - Dual 3-26V Low-Power Op Amp | onsemi
LM2904DMR2G

LM2904DMR2G - Dual 3-26V Low-Power Op Amp | onsemi

onsemi LM2904DMR2G is a dual, general-purpose operational amplifier with a 3 V to 26 V supply range, two amplifier circuits, and an 8-MSOP surface-mount package. The LM2904 family provides low power drain, supports single-supply or split-supply operation, and permits common-mode input voltages to extend toward ground or VEE. These characteristics make the device useful in industrial signal-conditioning, control, and sensor-interface circuits. An operational amplifier is a voltage-gain building block used throughout analog electronics. Its differential input stage compares two input voltages and drives an output to amplify the difference between them. The LM2904 belongs to the bipolar operational-amplifier hierarchy, combining two amplifier channels in one package for general-purpose precision, control, and instrumentation applications. The LM2904DMR2G provides two amplifier circuits, a gain-bandwidth product of 1 MHz, and a maximum supply voltage of 32 V. Its specified operating temperature range is -40°C to 105°C. The 3 V to 26 V operating supply range supports low-voltage systems as well as higher-voltage industrial circuits when the total supply and input limits are observed. The bipolar internal design favors low-cost, general-purpose signal conditioning rather than rail-to-rail input or output operation. Its common-mode input range extending to ground or VEE is particularly useful with single-supply sensors whose signals remain near the lower rail. Single-supply and split-supply operation gives designers flexibility when building signal paths around positive-only or bipolar reference voltages. Typical uses include low-side current monitoring, pressure and temperature sensor interfaces, audio preamplifier stages, industrial control loops, and general amplifier or buffer configurations. The two independent channels can process different signals or implement a more complete analog function within one compact 8-MSOP package. Designers should check input and output common-mode limits at the selected supply voltage and load current. Stable operation with capacitive loads may require an isolation resistor or an application-specific compensation network. PCB placement should keep input and feedback traces short, provide a stable ground reference, and avoid routing sensitive signals beside switching nodes or high-current power paths. This page combines the LM2904DMR2G package and operating characteristics with practical design guidance, verified drop-in candidates, application analysis, and a parameter-by-parameter comparison. It is intended to help engineers confirm compatibility, assess supply and thermal margins, and select an amplifier that can be implemented without unnecessary PCB redesign.

RFQ Kontak
LM2904DR2 - Dual 3-26V Operational Amplifier | onsemi
LM2904DR2

LM2904DR2 - Dual 3-26V Operational Amplifier | onsemi

The onsemi LM2904DR2 is a dual general-purpose operational amplifier designed for low-power signal-conditioning applications from a single supply or split supplies. It operates across a 3 V to 26 V total supply range, accepts inputs that extend toward ground or VEE, and is packaged in an 8-pin SOIC for standard surface-mount assembly. The device contains two amplifiers in one package while retaining the familiar LM358-family architecture. An operational amplifier is a high-gain analog building block used to amplify voltage differences, buffer signals, compare voltages, and drive feedback-controlled circuits. The dual operational amplifier category belongs to the broader hierarchy of operational amplifier, linear amplifier, analog IC, and semiconductor. This makes the LM2904DR2 suitable for both general-purpose precision-adjacent signal conditioning and conventional industrial control circuits where a low-power, dual amplifier simplifies board layout. The LM2904DR2 combines two amplifier channels in one 8-pin SOIC. Its single-supply operating range is listed as 3 V to 26 V, while the associated dual-supply capability supports operation from approximately plus or minus 16 V, corresponding to a 32 V total supply. The common-mode input range extends to ground in single-supply configurations and to VEE in split-supply configurations. These characteristics make each channel suitable for noninverting and inverting amplifier, voltage follower, comparator, and general feedback-control arrangements. The low-power operating characteristics allow the device to be used in battery-powered instrumentation, industrial sensing, sensor interfaces, and control systems where dual-channel analog processing is required without a high-power amplifier family. Its differential inputs support feedback arrangements in which one input receives the source signal and the other receives the feedback or reference network. The two independent channels can also process different signals within the same package. Typical applications include low-level sensor conditioning, current-loop receivers, audio preamplifier stages, active filtering, comparator circuits, and industrial control interfaces. In a current-loop receiver, for example, the amplifier can amplify a small voltage across a sense resistor while the common-mode range supports signals referenced toward the lower supply rail. In a dual-channel design, one channel can condition a measurement while the other performs monitoring or buffering. Layout should prioritize short feedback paths, stable input grounding, and careful decoupling of the supply pins. Place the device close to the analog signal source when trace lengths permit, route high-impedance input nodes away from switching nodes, and use the manufacturer datasheet pin description table when assigning PCB tracks. Decoupling requirements, exact electrical limits, and compensation guidance should be taken directly from the applicable onsemi datasheet. This page combines the exact LM2904DR2 ordering information with package, supply-voltage, application, and replacement guidance. It also distinguishes pin-compatible alternatives from merely similar amplifier functions, helping engineers evaluate PCB reuse, supply compatibility, and sourcing without changing the original 8-pin SOIC footprint.

RFQ Kontak
LM2904DR2G - Dual 3-32V Op Amp, 8-SOIC | onsemi
LM2904DR2G

LM2904DR2G - Dual 3-32V Op Amp, 8-SOIC | onsemi

onsemi LM2904DR2G is a dual general-purpose operational amplifier with two independent amplifier channels, a 3 V to 32 V supply-voltage range, and an 8-SOIC surface-mount package. The device supports single-supply or split-supply operation, and its common-mode input range extends to ground or VEE, making it suitable for systems using low positive supply voltages. An operational amplifier is an analog signal-processing IC that amplifies the voltage difference between its inverting and non-inverting inputs. The LM2904 belongs to the dual operational amplifier family within the broader operational amplifier, analog IC, and semiconductor hierarchies. Its two channels can amplify two signals independently, or one channel can be used as a buffer while the other performs amplification, filtering, or comparison. The principal advantages include low power drain, common-mode input operation extending to ground or VEE, and flexible single- or dual-supply configurations. The 3 V minimum supply supports modern low-voltage systems, while the 32 V maximum accommodates higher industrial rails. The -40°C to +105°C operating-temperature range supports applications across consumer, instrumentation, industrial-control, and power-management equipment. The LM2904 uses a bipolar operational-amplifier architecture. Each channel includes differential inputs and an output stage designed for general-purpose signal conditioning. Unlike rail-to-rail-input devices, its useful input range depends on the selected supply arrangement and common-mode limits. Designers should therefore verify signal levels against the operating conditions in the manufacturer datasheet rather than assuming full rail-to-rail input capability. Typical applications include low-side current monitoring, sensor-signal conditioning, active filtering, buffer stages, audio preamplification, threshold detection, and general industrial control. It is especially useful when a design requires operation from a single positive supply while processing signals that approach the negative supply rail, which is represented by ground in a single-supply circuit. For reliable implementation, place the input, feedback, and decoupling components close to their associated pins, use a stable low-noise power source, and check output-current and common-mode limits over the complete temperature range. Bypass capacitors should connect directly to the supply pins to minimize parasitic inductance and preserve stability. This product page combines the operating characteristics, pin assignments, application guidance, drop-in comparison, and practical layout considerations needed to evaluate the LM2904DR2G for a new analog signal chain.

RFQ Kontak