Mga Produkto (46,000+)

LM2904WHYDT - Dual General-Purpose Op Amp | STMicroelectronics
LM2904WHYDT

LM2904WHYDT - Dual General-Purpose Op Amp | STMicroelectronics

STMicroelectronics LM2904WHYDT is a dual general-purpose operational amplifier in an 8-pin SOIC package. The device contains two independent, high-gain, internally frequency-compensated amplifiers, enabling one package to provide two signal-conditioning channels. According to the manufacturer product information, it is intended for automotive and industrial control systems and can operate from a single supply or split supply over a wide voltage range. The low-power architecture makes it suitable for battery-operated equipment, instrumentation, sensor interfaces, and general analog control circuits. An operational amplifier is an analog integrated circuit that amplifies the difference between its inverting and non-inverting inputs. The op-amp category sits within analog signal-chain ICs and serves as a fundamental building block for sensors, filters, buffers, comparators, and closed-loop control systems. The LM2904 family combines internal frequency compensation with two amplifiers in one package, reducing board area compared with separate single-channel devices while preserving independent channels. The LM2904WHYDT is identified as a standard general-purpose amplifier with two single-ended circuits. Its internally compensated architecture allows operation without an external compensation network in many conventional closed-loop configurations. The device is intended for low-power applications and is particularly useful where a compact, general-purpose dual amplifier is preferable to a high-speed precision amplifier. The exact input offset, bandwidth, output-current, and temperature limits should be confirmed from the manufacturer datasheet before final circuit sign-off. Two independent channels can implement voltage followers, transimpedance stages, differential amplifiers, active filters, comparators, and motor or actuator-control loops. A common application is conditioning the output of a bridge sensor, potentiometer, or resistive divider before an ADC samples the signal. In automotive systems, the dual format can economize PCB space in body, climate, or powertrain-control modules where multiple low-power analog channels are required. The SOIC-8 package supports conventional surface-mount assembly and is suitable for lead-free production boards. Place each power pin close to a low-impedance decoupling network and route sensitive input traces away from switching nodes. Because the amplifiers are independent rather than sharing internal signal paths, grounding and supply layout should be designed to minimize channel-to-channel coupling. Verify the exposed operating limits and decoupling recommendations in the manufacturer datasheet for the exact automotive temperature grade. This page combines the manufacturer listing, distributor package identification, sourcing information, pin-compatible alternatives, and practical analog-design guidance. Use the Request a Quote form for current availability, lead time, and commercial terms, and use the official datasheet for authoritative electrical limits before layout release.

RFQ Kontak
LM2904WHYST - Dual 1.1MHz Op Amp | STMicroelectronics
LM2904WHYST

LM2904WHYST - Dual 1.1MHz Op Amp | STMicroelectronics

The STMicroelectronics LM2904WHYST is a dual general-purpose operational amplifier with two independent high-gain amplifiers, 1.1 MHz gain-bandwidth product, 0.6 V/us slew rate, and low input bias current of 200 nA per channel. The device is packaged in an 8-pin MiniSO package measuring 3.90 mm in body width. Its electrical characteristics support single-supply and dual-supply operation in industrial control, sensor signal conditioning, and general analog signal-processing systems. An operational amplifier is an analog amplifier that uses very high open-loop gain to compare or amplify a differential input signal. The LM2904 family belongs to the broader operational-amplifier hierarchy, which includes instrumentation, comparator, and rail-to-rail amplifier categories. The LM2904WHYST is intended for applications requiring two amplifiers, moderate bandwidth, low input bias current, and a compact surface-mount footprint rather than precision or high-speed performance. Key features include two amplifier channels, a 1.1 MHz gain-bandwidth product, a 0.6 V/us slew rate, approximately 200 nA input bias current, and 7 mV input offset voltage as identified for this device. The MiniSO-8 package reduces board area while retaining separate power, ground, input, and output connections for each channel. The automotive-oriented ordering code also supports use in temperature-qualified equipment, subject to the device's stated operating limits. Each channel operates as a general-purpose voltage-feedback amplifier, allowing implementation as an inverting amplifier, non-inverting amplifier, voltage follower, comparator-style circuit, or active filter. The two independent channels can process separate signals or be combined for differential, instrumentation, and gain-stage arrangements. The 1.1 MHz bandwidth is suitable for low-to-moderate frequency industrial signals, while the 0.6 V/us slew rate supports accurate reproduction of relatively slow input waveforms. Typical applications include low-side current sensing, industrial sensor interfaces, transducer amplification, audio preamplification, and general control loops. In each case, the low input bias current helps reduce source-loading errors, while the dual configuration can reduce the number of separate amplifier packages required on a board. The amplifier is best suited to signals where moderate bandwidth and common-mode performance are more important than rail-to-rail operation or very low offset. Designers should verify the input common-mode range, output swing, supply voltage, and stability requirements against the operating conditions before finalizing the circuit. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be biased to a valid common-mode voltage. Feedback-network values and source capacitance should be selected to maintain stable closed-loop operation across the intended gain and load range. This product record combines package, electrical, qualification, sourcing, and drop-in comparison information with practical circuit guidance. It is intended to accelerate engineering selection for compact dual-op-amp designs while clearly distinguishing direct replacements from alternatives that require compatibility review.

RFQ Kontak
LM2904WPT - Dual Low-Power Op Amp | STMicroelectronics
LM2904WPT

LM2904WPT - Dual Low-Power Op Amp | STMicroelectronics

The STMicroelectronics LM2904WPT is a dual, general-purpose operational amplifier in an 8-TSSOP package. The device contains two independent, high-gain operational amplifiers with internal frequency compensation and is designed for automotive and industrial control systems. According to the manufacturer datasheet description, the LM2904W and LM2904AW circuits operate from a single power supply over a wide range of voltages, while the low power-supply drain remains independent of the magnitude of the supply voltage. The LM2904 family belongs to the operational amplifier hierarchy: dual operational amplifier -> general-purpose amplifier -> analog signal-conditioning IC -> semiconductor. Its internally compensated architecture simplifies implementation because an external compensation capacitor is not required for closed-loop operation in typical voltage-follower and inverting-amplifier configurations. The two independent amplifiers can also be used in separate signal chains within the same circuit. The LM2904WPT is identified in the product listings as a 2-circuit, single-ended amplifier in an 8-TSSOP package. The related LM2904AW variant is also documented for automotive and industrial applications. Low power-supply drain, wide single-supply operation, and internal frequency compensation make this family suitable for sensor conditioning, control-loop amplification, audio and instrumentation interfaces, and general industrial electronics. Because the LM2904WPT is a general-purpose amplifier, application performance depends on the selected gain, feedback network, supply voltage, load, and operating temperature. The datasheet should be consulted for the exact input common-mode range, output swing, input bias current, input offset voltage, supply-current limits, and thermal limits before final circuit sign-off. For PCB implementation, route the two amplifier sections with short feedback paths, keep input and output nodes away from switching nodes, and place supply-bypass capacitors close to the device pins. A common ground reference and adequate copper area help preserve signal integrity in low-level analog circuits. This page summarizes the verified device identity, package, application positioning, drop-in sourcing options, and practical design considerations that are useful when evaluating the LM2904WPT for a new analog design.

RFQ Kontak
LM2904WYDT - Low-Power Dual Op Amp, 3-30V | STMicroelectronics
LM2904WYDT

LM2904WYDT - Low-Power Dual Op Amp, 3-30V | STMicroelectronics

STMicroelectronics LM2904WYDT is a low-power dual operational amplifier with two independent amplifiers, a 3 V to 30 V supply range, and a gain-bandwidth product of 1.1 MHz. The device is supplied in an 8-SOIC package configured for industrial temperature-grade operation. An operational amplifier is an analog signal-processing IC that uses high-gain differential amplification to compare or condition voltages. The LM2904 belongs to the dual general-purpose operational-amplifier category, combining two amplifier channels in one compact package. Its wide supply range makes it suitable for systems powered from industrial 24 V rails, split analog supplies, or lower-voltage circuits when the operating limits are respected. Key characteristics include two amplifier circuits with single-ended outputs, a 1.1 MHz gain-bandwidth product, operation across a 3 V to 30 V supply range, and a common 100 dB figure cited for the family. These characteristics support general-purpose signal conditioning, low-frequency amplification, feedback-based control, and analog sensor interfaces where a precision rail-to-rail amplifier is unnecessary. The LM2904 architecture is designed for dependable operation from conventional dual supplies, including positive and negative rails. Designers should verify input and output voltage limits, common-mode range, output-current capability, and stability requirements against the manufacturer datasheet for the selected operating condition. The two channels share a supply but otherwise operate independently. Typical uses include industrial sensor conditioning, audio preamplification, motor and actuator interfaces, current-loop signal processing, sample-and-hold circuits, and general DC signal amplification. The 1.1 MHz bandwidth is appropriate for low-frequency control and analog conditioning rather than high-speed video or RF signal chains. Decoupling remains important in precision analog systems. Place a suitable bypass capacitor close to each supply pin and keep feedback components and sensitive input traces away from switching nodes. Account for input bias current, input offset voltage, output swing, and load-capacitance stability when selecting external components. This product overview consolidates the exact LM2904WYDT package, electrical characteristics, sourcing terms, comparison parameters, and practical design guidance. It also identifies same-footprint family alternatives so engineers can assess temperature-grade, revision, and sourcing differences before approving a replacement.

RFQ Kontak
LM2904WYPT - Dual 1.1MHz Op Amp, 100dB, 8-TSSOP | ST
LM2904WYPT

LM2904WYPT - Dual 1.1MHz Op Amp, 100dB, 8-TSSOP | ST

The STMicroelectronics LM2904WYPT is a low-power dual operational amplifier with two independent, internally frequency-compensated amplifiers in an 8-pin TSSOP package. It provides approximately 1.1 MHz unity-gain bandwidth and 100 dB typical open-loop gain, making it suitable for general-purpose signal conditioning in automotive and industrial control systems. The device operates from a single power supply over a wide input-voltage range. An operational amplifier is an analog amplifier that uses very high open-loop gain and negative feedback to amplify a differential input signal. Within the broader semiconductor hierarchy, the LM2904WYPT is an amplifier IC, a general-purpose operational amplifier, and a dual-amplifier device. Its two independent channels make it economical for designs that require two amplifier functions in one compact surface-mount package. Internal frequency compensation means no external compensation network is required for ordinary closed-loop operation. This simplifies implementation in sensor interfaces, buffer stages, active filters, comparators, and control loops. The dual configuration also allows the two amplifiers to handle separate signals or to be cascaded when higher closed-loop gain is required. The LM2904 family targets automotive and industrial control systems where a single-supply amplifier, low power consumption, and stable operation across supply-voltage variations are important. Its wide common-mode and output-voltage ranges support sensors and control circuitry powered from a single rail, while the two independent channels keep the component count and board area below that of two separate single-amplifier packages. A key design consideration is the input-bias-current error produced by the differential input stage. In high-impedance sensor applications, resistor values must be selected so that bias-current-induced offset remains small compared with the sensed signal. Resistor thermal noise and the amplifier's own noise should also be checked together when working with low-amplitude analog signals. This page combines manufacturer-family characteristics, package information, pricing evidence, and application-oriented design guidance. It also identifies which same-package alternatives can be considered without requiring PCB changes, helping engineers compare sourcing options before releasing a production design.

RFQ Kontak
LM2904YDT - 30V Low-Power Dual Op Amp | STMicroelectronics
LM2904YDT

LM2904YDT - 30V Low-Power Dual Op Amp | STMicroelectronics

The STMicroelectronics LM2904YDT is a low-power dual operational amplifier with two independent amplifiers, a 30 V family voltage rating, a 0.6 V/µs slew rate, and an 8-pin SOIC package. It is intended for general-purpose signal-conditioning applications where two amplifier channels, low power consumption, and a tolerant supply-voltage range provide a practical combination of capability and board economy. An operational amplifier, or op amp, is a voltage-gain device used to amplify small input signals in analog signal chains. The LM2904 family belongs to the broader hierarchy of analog integrated circuits, signal amplifiers, operational amplifiers, and general-purpose amplifiers. Its differential inputs and single-ended outputs allow each channel to support common tasks such as buffering, gain amplification, voltage comparison, filtering, and instrumentation-style signal conditioning. The LM2904YDT provides two amplifier circuits in one 8-SOIC package. Its stated 30 V family rating supports operation from single-supply industrial signal-conditioning circuits, while the low-power architecture suits battery-powered and portable equipment. The 0.6 V/µs slew rate provides a concrete indication of how quickly the output can follow a changing input, making the device appropriate for low-to-moderate-bandwidth applications rather than high-speed signal paths. STMicroelectronics describes the LM2904 family as a low-power dual operational amplifier. The automotive-oriented Y suffix and automotive-grade classification make the LM2904YDT relevant to vehicle electronics, industrial controls, and other systems that require a dual amplifier in a compact surface-mount package. Because the package contains two channels, PCB area and component count can be reduced compared with separate single-channel amplifiers. Typical uses include low-frequency sensor conditioning, current-loop signal amplification, audio preamplification, active filtering, voltage buffering, and general industrial control. The device is also suitable for split-supply circuits when the signal can remain within the input and output common-mode limits specified by the manufacturer datasheet. Applications requiring wide bandwidth, rail-to-rail input or output operation, very low offset voltage, or low-noise performance should compare the LM2904YDT with precision or rail-to-rail amplifier families before finalizing the design. Designers should verify input common-mode range, output swing, output-current capability, and stability with the external compensation network for each specific operating point. Keep input and feedback traces short, place decoupling capacitors close to the supply pins, and avoid using the amplifier outside its stated supply and common-mode limits. A bypass capacitor near each device helps control supply-line noise on shared analog boards. This product page combines the LM2904YDT operating identity with package, application, drop-in replacement, and design guidance. It highlights where the conventional low-power dual op amp is appropriate and where precision, speed, or rail-to-rail characteristics may justify a different amplifier architecture.

RFQ Kontak
LM2904YPT - Dual 1.1MHz Op Amp | STMicroelectronics
LM2904YPT

LM2904YPT - Dual 1.1MHz Op Amp | STMicroelectronics

STMicroelectronics LM2904YPT is a low-power dual operational amplifier in an 8-TSSOP package, providing two independent general-purpose amplifier channels with single-ended outputs. The device is specified for 100 dB of open-loop voltage gain and 1.1 MHz of gain-bandwidth product, making it appropriate for signal-conditioning stages that require stable operation from low-frequency instrumentation through audio-range circuits. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LM2904 belongs to the dual operational amplifier family, combining two amplifier channels in one package. Within the broader hierarchy, it is a low-power bipolar operational amplifier, a general-purpose amplifier IC, and a component within the wider analog signal-processing and semiconductor product category. The LM2904YPT's two channels can be configured independently as inverting amplifiers, non-inverting amplifiers, comparators, buffers, or differential amplifier stages. Its 100 dB open-loop gain supports accurate signal amplification when closed-loop feedback controls the operating gain. The 1.1 MHz gain-bandwidth product establishes the bandwidth available for closed-loop operation, while the low-power characterization supports economical designs where amplifier power consumption is an important system constraint. This dual architecture reduces component count and PCB area when a board requires two amplifier functions. It is particularly useful in sensor interfaces, analog signal conditioning, active filters, low-level audio paths, and general industrial control circuits. Because both channels share one package, designers should also evaluate common thermal and supply conditions rather than treating the two amplifier sections as completely independent systems. Typical circuit implementation uses conventional negative feedback, input bias-current compensation where required, and suitable decoupling near the supply pins. Input and output signal levels must remain compatible with the device's operating limits, while stable feedback and suitable output loading are necessary to maintain expected performance. Signal-routing practices should minimize coupling between the high-gain inputs and nearby switching or digital nodes. This page combines the exact LM2904YPT configuration, verified distributor listings, drop-in replacement analysis, package-level pin information, and practical design guidance. It helps engineers narrow the selection before requesting a quote for the dual low-power operational amplifier in its compact 8-TSSOP package.

RFQ Kontak
LM2904YST - Dual Low-Power Op Amp, 8-MiniSO | STMicroelectronics
LM2904YST

LM2904YST - Dual Low-Power Op Amp, 8-MiniSO | STMicroelectronics

The STMicroelectronics LM2904YST is a dual, low-power bipolar operational amplifier designed for general-purpose signal conditioning. The device provides two independent amplifier channels in an 8-pin MiniSO package and is specified for supply voltages up to 30 V, including operation from ±15 V rails. Its low-power design, broad input-voltage capability, and single-ended outputs make it suitable for industrial control, sensor interfaces, audio stages, and general analog signal-processing circuits. An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LM2904 contains two such amplifier sections, allowing one package to process two related signals or to implement two stages of a larger circuit. As a bipolar operational amplifier, it provides input bias-current behavior and voltage-noise characteristics suited to many low-cost precision and control applications rather than the very low input bias current associated with CMOS or JFET input devices. The LM2904YST supports operation across a wide supply range and can operate with dual supplies such as ±15 V. The 30 V maximum supply rating provides useful headroom for industrial applications, while the low-power operating-current target reduces heat generation in battery- and line-powered equipment. Each channel uses a differential input arrangement and provides a single-ended output referenced to the negative supply rail. Common applications include buffering sensors, amplifying low-level control signals, and driving external circuitry within the amplifier’s output-current capability. The 8-MiniSO package is a compact surface-mount form factor that reduces board space compared with traditional through-hole SOIC packages. The YST ordering suffix identifies the tape-and-reel presentation, allowing the amplifier to be assembled through standard surface-mount production processes. Because operational-amplifier performance depends on surrounding passives and layout, input and feedback components should be positioned close to the relevant pins, while adequate supply bypassing should be placed directly across the device’s supply terminals. LM2904YST is appropriate for industrial instrumentation, feedback-control loops, transducer amplification, audio preamplification, and low-frequency analog filters. The dual-channel arrangement can reduce component count in designs using two separate gain stages. In designs requiring input offset current below the LM2904’s range, rail-to-rail precision, or operation from a single low-voltage supply, a CMOS-input amplifier may offer a better technical match even if it shares a similar package. Designers should verify input and output voltage limits at the selected supply voltage, confirm the required gain bandwidth and slew rate, and check that the planned load does not exceed the output-current capability. Input common-mode range, output swing, electrical-noise limits, and thermal performance should be checked against the worst-case operating conditions. Decoupling capacitors should be selected according to the manufacturer’s recommended application circuit and stability requirements. This product overview combines the manufacturer-distinguished LM2904YST configuration with package, application, cross-reference, and design-placement guidance. It supports faster component identification while emphasizing the distinctions engineers must validate before approving any analog signal-chain design.

RFQ Kontak
LM2924M Low-Power Op Amp/Comparator | Texas Instruments
LM2924M

LM2924M Low-Power Op Amp/Comparator | Texas Instruments

Texas Instruments LM2924M is a low-power dual-purpose analog IC containing two independent building blocks: a high-gain, internally frequency-compensated operational amplifier and a precision voltage comparator. The device is packaged in an 8-pin SOIC and is identified as an industrial-temperature-grade component. This combination allows one package to provide signal amplification and threshold detection without using separate amplifier and comparator packages. An operational amplifier is a voltage amplifier whose closed-loop gain is established by an external feedback network. A voltage comparator compares two input voltages and switches its output according to their relationship. The LM2924M combines these complementary functions in a single analog device, placing it in the operational-amplifier and comparator hierarchy while supporting transducer, sensing, control, and signal-conditioning applications. The internally frequency-compensated operational amplifier is designed to operate without an external compensation capacitor, simplifying implementation in basic gain configurations. Its comparator section provides an independent decision-making channel, allowing the two internal circuits to monitor or condition separate signals simultaneously. Because the amplifier and comparator are independent building blocks, their inputs and outputs can be used for different stages of a system. The National Semiconductor datasheet describes the LM2924M as a low-power operational amplifier and voltage comparator for precision voltage-amplification and related analog signal-processing needs. The 8-pin SOIC package provides a compact surface-mount format for industrial equipment, embedded controls, instrumentation interfaces, and mixed analog-digital circuit boards. Typical applications include transducers whose weak outputs require voltage amplification, sensor interfaces requiring a defined switching threshold, industrial control loops, and analog monitoring subsystems. The dual internal architecture can reduce board area when a design needs both continuous analog amplification and discrete threshold detection. For PCB implementation, assign the supply, ground, input, and output pins according to the manufacturer pin-description table and preserve the recommended input/output operating conditions. Confirm signal ranges, output states, stability requirements, and temperature limits against the device datasheet before connecting external transducers or logic interfaces. This page combines the device architecture, package details, sourcing guidance, verified replacement constraints, and practical application guidance. It also distinguishes confirmed drop-in choices from merely similar amplifier or comparator products, helping engineers avoid replacements that require PCB changes or behavioral redesign.

RFQ Kontak
LM2924MX - Low-Power Amplifier/Comparator | Texas Instruments
LM2924MX

LM2924MX - Low-Power Amplifier/Comparator | Texas Instruments

Texas Instruments LM2924MX is a low-power bipolar analog IC that combines an operational-amplifier function with voltage-comparator operation in an 8-pin SOIC package. It is identified as a single-function transducer-amplifier circuit, is designed for industrial-temperature use, and is supplied in a rectangular surface-mount SOP package. The LM2924MX therefore serves as a compact analog signal-conditioning component for systems that require amplification and threshold detection in one package. An operational amplifier is a voltage-controlled analog amplifier whose open-loop gain is made large enough to amplify small signals accurately when negative feedback is applied. A voltage comparator compares one input voltage with another and changes its output state when a threshold is crossed. Together, these functions form part of the broader linear and mixed-signal IC hierarchy, where they support sensor conditioning, control loops, signal detection, and industrial interface circuits. The LM2924MX combines three notable product attributes. First, its bipolar construction places it in the classical family of analog amplifier ICs. Second, its single-function analog-circuit architecture supports compact implementation of transducer and signal-conditioning paths. Third, the 8-pin surface-mount SOIC package permits automated assembly while reducing board area compared with larger through-hole packages. Its industrial temperature grade also positions it for equipment operating beyond typical commercial-temperature conditions. LM2924MX is identified as a low-power operational amplifier and voltage comparator. This dual operating role allows the same device to amplify a low-level analog signal and evaluate whether that signal has crossed a defined reference level. In feedback-based configurations, the amplifier behavior supports closed-loop gain; in open-loop threshold service, the comparator behavior provides a digital indication of an analog condition. Exact gain-bandwidth, input-offset, supply-voltage, and output-current limits should be confirmed from the manufacturer datasheet before final circuit sizing. Typical uses include bridge or resistive-transducer signal conditioning, industrial sensor interfaces, low-level control-signal amplification, threshold detection, and alarm-generation circuits. The 8-pin SOIC footprint is suitable for compact analog boards where a surface-mount part is preferred and where signal conditioning must be placed close to the sensor or source to minimize susceptibility to interference. Designers should determine the allowable supply range, input common-mode range, output swing, input-offset voltage, noise, and comparator propagation behavior from the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, while sensitive input routing should avoid switching nodes and high-current return paths. Feedback resistors and any hysteresis network must be evaluated for the required gain, offset, and threshold stability. This product page consolidates the exact package, temperature-grade, circuit-type, and lifecycle information for LM2924MX, maps suitable analog applications, and provides engineering guidance for layout, compensation, and sourcing. It also distinguishes confirmed drop-in replacements from merely similar amplifier or comparator families so that PCB reuse decisions remain technically defensible.

RFQ Kontak
LM293AD - Dual Differential Comparator, 2-36V | Texas Instruments
LM293AD

LM293AD - Dual Differential Comparator, 2-36V | Texas Instruments

Texas Instruments LM293AD is an industrial-grade dual differential comparator with two independent comparison channels, a 2 V to 36 V supply range, rail-to-rail input operation, and open-collector/open-drain outputs. The device is packaged in an 8-pin SOIC and is designed for sensing and control applications involving wide input and output voltage conditions. A differential comparator is an integrated circuit that compares two input voltages and changes its output state according to their relationship. Its two channels can monitor thresholds, detect crossings, implement window functions, or generate control signals. The LM293 belongs to the comparator hierarchy within analog interface ICs, where it bridges analog sensing and digital control logic. The LM293AD operates from 2 V to 36 V and provides a response time of approximately 300 ns. Its common-mode input range includes ground, and its differential input range can equal the maximum-rated supply voltage of ±38 V according to the manufacturer product information. Open-collector outputs support wired logic, pull-up arrangements, level translation, and compatibility with TTL, MOS, and CMOS systems. Each comparator section compares an inverting input with a non-inverting input. When the non-inverting input is higher, the corresponding open-collector output transistor turns off; when the inverting input is higher, the output transistor turns on. An external pull-up resistor is required for conventional open-collector operation. The two channels share the supply pins but retain separate input and output pins. Typical uses include industrial sensor interfaces, battery monitoring, power-supply fault detection, overvoltage protection, relay or LED indication, and control systems that compare an analog voltage against a reference. The wide operating supply range is useful when the comparator must tolerate industrial transients while operating from a higher-voltage rail. Designers should verify input and output absolute maximum ratings, provide adequate pull-up resistors, maintain a valid common-mode range, and account for output-current limits when several wired-open-collector outputs share a bus. Because the outputs can sink current but cannot source it independently, external pull-ups determine the high logic voltage and rise-time behavior. This product page combines manufacturer specifications, verified distributor listings, same-package replacement guidance, and practical comparator-design notes. It helps engineers evaluate the LM293AD for industrial threshold detection, protection, monitoring, and open-collector interface designs without confusing it with open-drain parts that use different output structures.

RFQ Kontak
LM293ADR - 36 V Dual Comparator | Texas Instruments
LM293ADR

LM293ADR - 36 V Dual Comparator | Texas Instruments

The Texas Instruments LM293ADR is a dual differential comparator designed for industrial applications, with two comparator channels, a 2 V to 36 V supply range, and an 8-pin SOIC package. The device supports open-collector and open-drain outputs and is specified for an extended temperature range of -25°C to +85°C. According to the manufacturer product page, its common-mode input voltage range includes ground, making it suitable for sensing signals close to the lower supply rail. A differential comparator is an analog integrated circuit that compares two input voltages and produces a digital output indicating which input is higher. The LM293 belongs to the comparator hierarchy within interface ICs, where analog input conditioning is converted into a logic-compatible decision. Its open-collector output allows the output state to be defined by an external pull-up resistor, making the device useful in wired-logic, relay-driving, and open-drain bus interfaces. The LM293ADR provides several characteristics suited to robust circuit design. Its 36 V maximum supply permits operation in industrial environments, while its rail-to-rail input capability allows comparisons near ground. The manufacturer identifies the output as compatible with TTL, MOS, and CMOS logic. The differential input voltage range can equal the maximum-rated supply voltage, and the device is specified for operation over a 2 V to 36 V total supply range. The LM293A family uses two independent comparator sections within one package. Each section has inverting and non-inverting inputs, an output, and shared supply connections. The open-collector architecture requires a pull-up resistor when the output must actively drive high. The result is a flexible interface between high-voltage or low-level analog signals and digital control logic without requiring a rail-to-rail push-pull output stage. Typical applications include overvoltage and undervoltage detection, sensor-threshold conditioning, industrial control interfaces, relay or solenoid drivers, window or level comparators, and open-drain bus signaling. The dual-channel configuration allows two related threshold decisions to be implemented in one package, reducing board area when both channels operate from the same supply. When designing the circuit, choose the pull-up resistor for the required sink current and logic level, and verify that all input pins remain within the common-mode range at every supply condition. Because the output is open-collector, a floating output can occur without a pull-up. Confirm timing against the application’s threshold-crossing rate and maintain adequate supply decoupling close to the power pin. This page combines the manufacturer’s electrical and ordering information with package guidance, comparison criteria, sourcing support, and practical application notes to help engineers evaluate the LM293ADR for new and existing comparator designs.

RFQ Kontak
LM293AM - Dual Differential Comparator, 36 V, SOIC-8 | onsemi
LM293AM

LM293AM - Dual Differential Comparator, 36 V, SOIC-8 | onsemi

The onsemi LM293AM is a dual differential comparator designed for single-supply operation up to 36 V or dual-supply operation up to ±18 V, and it is available in an 8-pin SOIC package. Its differential inputs allow two voltages to be compared, while the open-collector output structure supports flexible interface and pull-up arrangements in control, sensing, and protection circuits. A differential comparator is an analog integrated circuit that compares two input voltages and changes its output state according to their relationship. The dual configuration provides two independent comparators in one package. When used with an external pull-up, an open-collector output can drive TTL, MOS, or CMOS-compatible circuitry while also allowing wired logic, level translation, or system reset behavior. The LM293AM belongs to the comparator hierarchy within amplifier and interface ICs. Key features include single-supply operation to 36 V, dual-supply operation to ±18 V, a typical low-current drain of 800 µA, and a typical input bias current of 25 nA. The device can compare input voltages near ground potential and is compatible with multiple logic families. Its low input bias current helps reduce source-loading effects in high-impedance sensing networks, while the wide supply range supports industrial and automotive-style control environments. The LM293AM uses open-collector outputs rather than push-pull outputs. This architecture provides a useful advantage when a comparator output must remain inactive until an external pull-up supplies the required logic-high voltage. It also supports open-wired signal arrangements, but every application must include the appropriate pull-up resistor and verify that the resulting rise time is acceptable. The operating common-mode range, differential input limits, output sink capability, and timing behavior should be checked against the manufacturer datasheet for the selected manufacturer version. Typical applications include industrial control systems, power-supply supervision, motor and solenoid protection, battery monitoring, sensor-threshold conditioning, window or level detection, and general-purpose logic interfaces. The dual comparator arrangement is particularly useful when one circuit monitors two related thresholds or when an enable function and a fault signal can be implemented with the two channels in a compact footprint. For PCB design, place the device so that sensitive input traces remain away from switching nodes and output pull-up routing. Keep input and output paths separate to reduce feedback through supply or board-level coupling. Confirm the logic-high level, output rise time, input common-mode range, supply decoupling requirements, and operating temperature range before releasing the design for production. This page combines manufacturer-family operating limits, package details, sourcing guidance, replacement analysis, and practical PCB considerations to support faster component selection. Review the complete pin assignment and electrical characteristics in the LM293AM datasheet before layout, particularly when the same circuit must accommodate multiple LM293-family variants.

RFQ Kontak
LM293AN - Dual Open-Collector Comparator | STMicroelectronics
LM293AN

LM293AN - Dual Open-Collector Comparator | STMicroelectronics

The STMicroelectronics LM293AN is a low-power dual voltage comparator with two independent comparator channels, open-collector and open-drain outputs, and an 8-DIP package. The device is designed for general-purpose signal comparison and can operate from a single supply over a wide voltage range, while split-supply operation is also possible. Its listed rail-to-rail input designation, ground-referenced common-mode capability, and TTL, MOS, and CMOS output compatibility make it suitable for threshold detection, level translation, and analog-control systems. A voltage comparator is an integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. In this role, LM293AN belongs to the comparator IC hierarchy within analog and mixed-signal semiconductors. Each of its two channels can evaluate a non-inverting input against an inverting input, allowing one package to perform two related comparisons while keeping channel operation independent. The LM293 family documentation identifies low power consumption as a defining characteristic and specifies input-offset voltage as low as 2.0 mV maximum for the associated two-comparator family. Open-collector outputs provide flexibility when the destination device requires a pull-up resistor, particularly in wired logic, relay-driver, and legacy digital-interface applications. The outputs are also listed as compatible with TTL, MOS, and CMOS logic families. Operation from a single supply is central to the device design. The common-mode input range includes ground, while the differential input voltage can extend to the maximum-rated supply voltage of ±38 V according to TI's LM293 family information. The 8-DIP mechanical format provides through-hole access to the two comparator channels, power, ground, and output connections. Typical uses include industrial control thresholds, sensor-interface decisions, window comparators, oscillator and timer designs, and general logic level conditioning. The two independent channels can also implement a larger comparator arrangement through external resistor networks. Open-collector outputs make pull-up selection an important part of the interface design because the output cannot directly drive a logic high without this external support. The main design consideration is that open-collector outputs require correctly selected pull-up resistors and adequate logic-level rise time at the driven node. Supply decoupling, input-source impedance, output load, and common-mode headroom should be reviewed against the application's operating conditions. This page consolidates the verified device identity, package information, sourcing links, and practical comparator-selection guidance.

RFQ Kontak
LM293D - Dual Differential Comparator, 8-SOIC | TI
LM293D

LM293D - Dual Differential Comparator, 8-SOIC | TI

The Texas Instruments LM293D is a dual differential comparator designed for low-voltage operation from a single supply or split supplies. The verified distributor listing identifies it as a standard general-purpose comparator with open-collector, open-drain, rail-to-rail operation in an 8-SOIC package. The device contains two independent comparator channels, making it suitable for threshold detection, level shifting, window monitoring, and basic analog control systems. According to the Texas Instruments LM293 product page, the device is a dual differential comparator in an industrial-grade family; detailed electrical limits are not supplied in the verified excerpts and therefore remain marked for data completion. A comparator is an analog signal-conditioning IC that compares two input voltages and produces a logic-level output indicating which input is higher. A differential comparator belongs to the broader comparator, amplifier, and analog interface hierarchy, while the LM293D is specifically a low-power, dual-channel comparator for embedded and control applications. Its two independent channels allow simultaneous comparison of two signal pairs, provided the device operates within the manufacturer-rated common-mode and supply limits. The verified TI page states that the LM293 family supports wide supply-voltage operation, including systems using split power supplies. TI also states that the B-version is a drop-in replacement for LM293, LM393, and LM2903; however, the provided data does not establish that every related suffix is electrically identical for every use condition. The LM293D listing identifies open-collector/open-drain and rail-to-Rail output characteristics, which are important when interfacing with pull-up-based digital systems. Typical uses include monitoring a battery or power rail, detecting sensor thresholds, comparing external reference voltages, and implementing basic overvoltage or undervoltage indication. The open-drain output requires an external pull-up resistor when the output must rise to a defined logic level. Because the verified data does not provide exact input-offset, response-time, supply-current, or temperature values, those specifications are retained as data-needed markers rather than inferred from related devices. For PCB design, place the IC close to the compared signals and use short, low-noise routing for high-impedance input nodes. Keep pull-up resistors close to open-drain outputs, and account for input common-mode range and supply polarity in both single-supply and split-supply systems. The LM293D is not a power semiconductor, so SOA data is not applicable.

RFQ Kontak
LM293DG - Dual Precision Comparator, 2-36V, SOIC-8 | onsemi
LM293DG

LM293DG - Dual Precision Comparator, 2-36V, SOIC-8 | onsemi

The onsemi LM293DG is a dual independent precision voltage comparator in an 8-pin SOIC package, built for single or split supply operation across a 2 V to 36 V supply range. Each channel offers an input offset voltage as low as 2.0 mV, a 1.3 microsecond response time, and a supply current of about 400 microamps per channel, with an open-collector (open-drain) output stage compatible with TTL, MOS and CMOS logic. A comparator is a differential amplifier used as a simple decision element: it compares two input voltages and switches its output state when the non-inverting input rises above the inverting input. The comparator category sits above discrete transistor switches in the signal-conditioning hierarchy and below instrumentation amplifiers in the analog IC family, sitting in the amplifier IC / signal conditioning control group of parts such as op amps, references and sensor interface ICs. The LM293 series is distinguished from general-purpose comparators by its low input offset voltage, wide supply range and ability to operate with the common-mode input range extending to ground, which makes it a strong fit for single 5 V or single 12 V systems where the signal of interest lives near the negative rail. The two channels are fully independent, each with its own pair of inputs and output. The open-collector output stage is the key architectural feature: the output transistor sinks current but never sources it, so an external pull-up resistor to the supply or logic rail is required to establish a valid high level. That architecture permits level shifting to any voltage up to the maximum supply, wired-AND bus tying, and direct drive of relay or solenoid drivers without a buffer stage. Because the output stage is a bipolar NPN transistor, output sink current is limited compared with modern CMOS comparators. Typical applications include overvoltage and undervoltage protection in linear and switching power supplies, battery and pack monitoring window comparators, motor stall and over-current detection, industrial sensor thresholding, and automotive-style sensor protection. The SOIC-8 package with 1.27 mm lead pitch supports both through-hole assembly and standard surface mount reflow, and the -25 C to +85 C ambient range covers industrial and consumer equipment. When designing with the LM293DG, always fit a pull-up resistor on each output and check the sink current against the pull-up value and the load. If your design needs rail-to-rail input operation, push-pull outputs, or a supply below 2 V, a CMOS comparator is the better choice; if it needs low offset with wide supply and open-drain flexibility, the LM293DG remains a proven, low-cost choice. This page consolidates manufacturer specifications, drop-in replacement candidates, pin-level detail and practical design guidance so that you can qualify the LM293DG for an existing board revision without redrawing the footprint.

RFQ Kontak
LM293DGKR - Dual 2-36V Comparator | Texas Instruments
LM293DGKR

LM293DGKR - Dual 2-36V Comparator | Texas Instruments

The Texas Instruments LM293DGKR is a dual differential comparator with two independent comparator channels, a 2 V to 36 V supply range, and a 300 ns response time, housed in an 8-pin VSSOP package. Each channel uses open-collector output architecture, making the device suitable for wired logic interfaces, threshold detection, and systems requiring a pull-up resistor. A differential comparator is an analog integrated circuit that compares two input voltages and produces a binary output indicating which input is higher. The LM293 belongs to the voltage-comparator hierarchy within interface and signal-conditioning semiconductors. Its two channels can operate independently, allowing one package to perform two comparison functions while reducing board area and simplifying component procurement. The principal operating characteristics include a 2 V to 36 V supply range, a 300 ns response time, and approximately 200 uA supply current. The open-collector outputs can sink useful levels of output current while the external pull-up resistor determines the high output voltage. Rail-to-rail input operation is identified for this device, while its industrial operating range of -40 C to +85 C supports laboratory, control-system, and industrial equipment. Each internal channel compares its noninverting and inverting inputs. Because the outputs are open collector, both channels can be tied together when wired-OR logic is required. The low output saturation behavior also permits direct interfacing with TTL, MOS, and CMOS-compatible external circuitry. Separate ground, supply, input, and output connections make the device straightforward to use in both single-supply and split-supply arrangements, subject to the applicable input limits. Typical uses include power-rail monitoring, industrial sensor threshold detection, battery and charger supervision, window-comparator circuits, control-loop signal conditioning, and logic-level translation where an open-drain interface is advantageous. The dual-channel configuration is particularly useful when a design requires two related decisions, such as an upper threshold and a lower threshold around the same monitored quantity. Designers should select an external pull-up resistor for each open-collector output and confirm that its resistance keeps output rise time and sink current within system requirements. Input and supply connections should be kept short, with suitable local bypassing placed close to the device. Thermal and common-mode limits must be checked across the full operating range, especially in industrial systems with long wiring and noisy power sources. This product overview combines the LM293 family identity, verified package and ordering information, practical comparator design guidance, drop-in family alternatives, and a specification comparison intended to accelerate component selection and PCB planning.

RFQ Kontak
LM293DMR2 - Dual Precision Comparator, 36 V | onsemi
LM293DMR2

LM293DMR2 - Dual Precision Comparator, 36 V | onsemi

The onsemi LM293DMR2 is a dual low-offset voltage comparator with two independent comparison channels, a 2 V to 36 V supply range, open-collector outputs, and an 8-pin TSSOP package. Each channel can operate from single or split power supplies, allowing common-mode input signals to approach ground during single-supply operation. The low input offset voltage, specified as low as 2.0 mV, supports accurate threshold detection in industrial, automotive, and consumer circuits. A voltage comparator is an analog signal-conditioning IC that compares two input voltages and produces a digital logic state at its output. The LM293 belongs to the comparator hierarchy, which includes differential comparators, window comparators, and precision comparators. By converting an analog threshold relationship into an open-collector logic indication, this type of device bridges analog measurement circuits and digital control, monitoring, or protection systems. The principal features include two independent comparators, low offset voltage, a common-mode input range extending to ground under single-supply operation, and open-collector outputs that can sink current from multiple compatible devices. The 2 V to 36 V operating supply range accommodates 5 V, 12 V, and 24 V systems. The onsemi datasheet also identifies the device as suitable for consumer, automotive, and industrial applications where reliable voltage-level detection is required. Each comparator channel is independent, allowing one device to perform two unrelated threshold measurements. The open-collector architecture requires an external pull-up resistor and provides a wired-output capability when several comparator outputs share a bus. This architecture does not actively drive the output high, but it offers flexible voltage-level adaptation and enables wired-AND behavior when output collectors are connected. Typical uses include monitoring a 12 V or 24 V automotive battery, detecting overvoltage and undervoltage conditions in industrial power systems, comparing sensor outputs with adjustable thresholds, and providing simple supervisory functions in consumer equipment. The grounded common-mode capability is especially useful in single-supply systems where the signal of interest begins near 0 V and cannot be compared reliably by a comparator with a restricted input range. For robust PCB implementation, place input resistors close to the comparator pins to limit differential pickup and route the inputs away from switching nodes and high-current paths. Select the external output pull-up for the intended logic voltage, and confirm that its maximum sink current remains within the device output ratings. Check that the common-mode and differential input voltages remain within the absolute maximum limits during power transients. This product page combines the manufacturer specifications, package and pin information, drop-in replacement analysis, comparison data, and practical PCB guidance to accelerate design review and sourcing. The technical recommendations focus on preserving the LM293DMR2 role as a reliable, low-offset dual comparator while making package, electrical, and supply constraints explicit before layout release.

RFQ Kontak
LM293DR - Dual Differential Comparator, 8-SOIC | TI (Tape & Reel)
LM293DR

LM293DR - Dual Differential Comparator, 8-SOIC | TI (Tape & Reel)

The Texas Instruments LM293DR is a dual differential comparator designed for low-voltage operation from a single supply or split supplies. The verified distributor listing identifies it as a standard general-purpose comparator with open-collector, open-drain, rail-to-rail operation in an 8-SOIC package. The device contains two independent comparator channels, making it suitable for threshold detection, level shifting, window monitoring, and basic analog control systems. According to the Texas Instruments LM293 product page, the device is a dual differential comparator in an industrial-grade family; detailed electrical limits are not supplied in the verified excerpts and therefore remain marked for data completion. A comparator is an analog signal-conditioning IC that compares two input voltages and produces a logic-level output indicating which input is higher. A differential comparator belongs to the broader comparator, amplifier, and analog interface hierarchy, while the LM293DR is specifically a low-power, dual-channel comparator for embedded and control applications. Its two independent channels allow simultaneous comparison of two signal pairs, provided the device operates within the manufacturer-rated common-mode and supply limits. The verified TI page states that the LM293 family supports wide supply-voltage operation, including systems using split power supplies. TI also states that the B-version is a drop-in replacement for LM293, LM393, and LM2903; however, the provided data does not establish that every related suffix is electrically identical for every use condition. The LM293DR listing identifies open-collector/open-drain and rail-to-Rail output characteristics, which are important when interfacing with pull-up-based digital systems. Typical uses include monitoring a battery or power rail, detecting sensor thresholds, comparing external reference voltages, and implementing basic overvoltage or undervoltage indication. The open-drain output requires an external pull-up resistor when the output must rise to a defined logic level. Because the verified data does not provide exact input-offset, response-time, supply-current, or temperature values, those specifications are retained as data-needed markers rather than inferred from related devices. For PCB design, place the IC close to the compared signals and use short, low-noise routing for high-impedance input nodes. Keep pull-up resistors close to open-drain outputs, and account for input common-mode range and supply polarity in both single-supply and split-supply systems. The LM293DR is not a power semiconductor, so SOA data is not applicable.

RFQ Kontak
LM293DR2G - Dual 36V Comparator | onsemi | Signal Control
LM293DR2G

LM293DR2G - Dual 36V Comparator | onsemi | Signal Control

The onsemi LM293DR2G is a dual precision voltage comparator rated for 2 V to 36 V operation, with a 1.3 µs response time and open-collector, open-drain outputs in an 8-pin SOIC package. The device contains two independent comparator channels and can operate from a single supply or split supplies, making it suitable for industrial threshold detection, sensing, and control circuits. A voltage comparator is an analog signal-conditioning device that compares two input voltages and changes its output state when the non-inverting input exceeds the inverting input. Within the broader hierarchy of semiconductor components, the LM293DR2G belongs to the comparator category, analog signal-conditioning ICs, and power-management-adjacent control devices. Its two independent channels allow one package to perform two comparisons while sharing a common supply and ground. The principal operating characteristics include a 2 V to 36 V supply range, a 1.3 µs response time, and a dual open-collector output architecture. The output structure can sink useful load current and requires an appropriate pull-up arrangement when driving subsequent digital stages. According to the onsemi LM293 family information, input offset voltage can be as low as 2.0 mV, while the LM293 series is designed for common-mode input operation down to ground with single-supply operation. Each internal channel has differential inputs and an independently controlled output. Separate inputs allow the circuit designer to define the polarity of each decision, while separate output stages provide isolation between the two comparator functions. The 8-pin SOIC package supports conventional surface-mount assembly, but exposed-pad thermal management is not part of this package. Exact offset-voltage limits, input bias current, output-current limits, and channel-matching figures should be selected from the ordering information for the exact grade. Typical uses include industrial sensor thresholds, motor and actuator control, power-supply monitoring, window or level detection, and general signal conditioning. In these systems, the comparator converts an analog relationship between two voltages into a logic-compatible indication that downstream control logic can process. The 36 V maximum supply capability is especially useful when the sensing circuit operates from an industrial bus rather than a low-voltage logic rail. For dependable operation, treat each open-drain output as requiring a pull-up to the supply used by the receiving logic. Keep input and feedback traces short, provide a local supply bypass capacitor, and confirm that input voltages remain within the applicable common-mode and absolute-maximum limits. Account for output rise time after the pull-up resistor is added because the stated 1.3 µs response describes comparator propagation behavior, not the complete RC-controlled transition at the output node. This product record combines the manufacturer family description with package, supply, temperature, and response-time details, then adds application guidance, pin-level implementation notes, and same-footprint comparison choices. These engineering views help designers evaluate the LM293DR2G as a dual comparator rather than treating it only as an eight-pin logic IC.

RFQ Kontak
LM293DRE4 Dual Differential Comparator 36V | Texas Instruments
LM293DRE4

LM293DRE4 Dual Differential Comparator 36V | Texas Instruments

The Texas Instruments LM293DRE4 is a dual differential comparator IC designed for single-supply or split-supply operation, with a maximum tested supply voltage of 36 V and an 8-SOIC package. The device contains two independent comparators with open-collector, open-drain outputs, allowing the output state to be pulled up externally. Its wide supply-voltage range, low supply-current drain of approximately 0.4 mA per comparator, and input common-mode range that includes ground make it suitable for industrial voltage-threshold, sensing, and control applications. A comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM293 belongs to the comparator category within analog signal-chain and power-management ICs, rather than acting as an amplifier or regulator. Two comparators in one package provide independent channels for monitoring two thresholds, controlling two loads, or implementing a window-detection function. The open-collector outputs are useful for wired logic, relay-driver interfaces, and systems requiring a pull-up resistor. The main electrical characteristics include operation from a single supply or dual supplies, a 2 V to 36 V difference between supply rails, a common-mode input voltage range that includes ground, and low output saturation voltage. The LM293 is specified as compatible with TTL, MOS, and CMOS logic levels. The output structure can sink current from an external pull-up while providing a predictable low-level output, allowing designers to select the pull-up voltage independently of the comparator supply. The LM293 architecture is based on two independent comparator channels rather than a shared output. This arrangement allows each channel to use separate non-inverting and inverting inputs while sharing the device supply pins. The inputs are intended for low-power threshold sensing, and the operating range supports both traditional positive-supply circuits and circuits using ground as the lower input reference. Open-collector outputs require an external pull-up when a valid high output is required. Typical applications include industrial process-limit detection, battery and power-supply monitoring, sensor signal conditioning, overvoltage and undervoltage protection, relay or solenoid control interfaces, and window comparators. The comparator can also be used as a simple line-driver or discrete-amplifier element in low-frequency control circuits. Because the output is open collector, the pull-up resistor and load current must be selected to match the desired logic voltage and switching speed. For PCB design, place the decoupling capacitor close to the supply and ground pins, and route comparator inputs away from switching nodes and high-current paths. The 8-SOIC footprint allows straightforward through-hole assembly and rework. The pull-up resistor should connect from each output to the logic rail used by the receiving device. Confirm the input voltages, supply current, output sink current, and common-mode limits against the application before releasing the design. This product page combines the manufacturer’s LM293 family information, exact-MPN sourcing details, pin-level integration guidance, and drop-in replacement analysis. It is intended to help engineers move from component identification to schematic review, footprint verification, and robust analog threshold-circuit design.

RFQ Kontak
LM293DRG3 - Dual Differential Comparator | Texas Instruments
LM293DRG3

LM293DRG3 - Dual Differential Comparator | Texas Instruments

The Texas Instruments LM293DRG3 is a dual differential voltage comparator in an 8-pin SOIC package. The device contains two independent comparison channels, supports ±15 V single-ended or 30 V total supply operation, and provides open-collector, open-drain outputs compatible with TTL, MOS, and CMOS logic. Its common-mode input range includes ground, allowing operation from a single positive supply, while the differential input range can extend to ±38 V. A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the difference crosses a defined threshold. The LM293 belongs to the comparator hierarchy, which also includes differential comparators and open-collector interface comparators. These devices bridge low-level analog sensing and digital control by converting an analog condition into a logic-readable result. The LM293DRG3 offers two independent comparators, rail-to-rail output behavior, and low output saturation voltage. Its open-collector outputs permit wired-AND connections and external pull-up selection, making the device adaptable to different logic families and voltage domains. The common-mode input range including ground is particularly useful in battery-powered and industrial systems powered from a single rail. Each channel compares a non-inverting input with an inverting input and uses open-drain output transistors to indicate the polarity of the differential voltage. The outputs can sink current while remaining in a high-impedance state when inactive. Because the output stage does not actively drive a high voltage, pull-up resistors are required when a logic-high level is needed. Differential input protection and common-mode limits must be respected during fault conditions. Typical uses include monitoring a sensor output, detecting supply thresholds, comparing an analog measurement with a reference, generating window-limit signals, and supporting industrial control logic. Two independent channels allow related threshold functions to be implemented in one package, reducing component count while preserving separate input and output isolation. Designers should select pull-up resistors to suit the destination logic voltage and sink-current budget, connect an unused comparator input to a defined valid potential, and verify input and output behavior across the full supply range. This page combines ordering information, package details, drop-in replacement guidance, comparison data, and practical design guidance for faster component selection.

RFQ Kontak
LM293DRG4 - Dual Open-Collector Comparator | Texas Instruments
LM293DRG4

LM293DRG4 - Dual Open-Collector Comparator | Texas Instruments

The Texas Instruments LM293DRG4 is a dual differential comparator with two independent channels, open-collector outputs, and an 8-pin SOIC package. It supports single-supply operation over a wide voltage range and dual-supply operation when the total supply difference is between 2 V and 36 V. Each channel compares an inverting input with a non-inverting input and provides a logic-compatible indication of the input relationship. A comparator is an analog integrated circuit that evaluates two voltages and changes its output state when one input crosses the other. Within the signal-chain hierarchy, the LM293 belongs to the comparator class, which sits alongside amplifiers and other analog interface ICs used to convert continuous voltage relationships into binary logic decisions. The LM293's open-collector outputs are useful when a system needs a pulled-up logic signal, wired logic, level translation, or an adjustable output rise time. The LM293 family is specified as a dual differential comparator for industrial applications. The LM293DRG4 ordering code identifies the 8-SOIC package and tape-and-reel shipping configuration. Its two channels are independent, allowing one device to implement two threshold decisions. Open-collector outputs also permit multiple devices to share a common pull-up bus when the system designer confirms that the resulting wired-AND behavior is intentional. The device can operate from a single supply or from positive and negative supplies. The manufacturer states that the common-mode input range includes ground, that the differential input range equals the maximum-rated supply voltage, and that the output is compatible with TTL, MOS, and CMOS logic. The LM293B version is identified as a drop-in replacement for LM293, LM393, and LM2903 families, providing a useful basis for qualified equivalent selection. Typical applications include power-supply threshold detection, sensor-signal conditioning, industrial control interfaces, battery monitoring, and digital logic level translation. In a sensor interface, the non-inverting input can receive a reference voltage while the inverting input receives the sensed signal, allowing the open-collector output to indicate when the signal crosses the selected threshold. The output requires an external pull-up because the LM293 does not actively drive its output high. Designers should account for input offset voltage, common-mode limits, supply voltage, output pull-up resistance, and propagation delay. Input components should also prevent excessive differential input voltage and protect sensitive sensor nodes from electrostatic discharge. Because the output is open collector, the pull-up resistor and its placement materially affect rise time, power consumption, and susceptibility to interference. This page combines the LM293 family architecture, verified ordering and package information, practical replacement criteria, threshold-comparison guidance, and PCB-focused design considerations. It also distinguishes genuine pin-compatible choices from options that require changes to output pull-ups, supply arrangements, or board layout.

RFQ Kontak
LM293DT - Dual 36V Low-Power Comparator | STMicroelectronics
LM293DT

LM293DT - Dual 36V Low-Power Comparator | STMicroelectronics

STMicroelectronics LM293DT is a low-power dual voltage comparator containing two independent comparator channels in an 8-pin SOIC package. Each channel supports a single supply from 2 V to 36 V or dual-supply operation, while the input stage accepts input voltages spanning the supply rails. The device uses open-collector output stages suitable for driving wired-AND, open-drain, and pull-up-based interfaces. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level output indicating which input is higher. The LM293 belongs to the comparator hierarchy, where a comparator is a signal-conditioning IC used between sensors, amplifiers, reference voltages, and digital control logic. Its two independent channels allow one package to perform two threshold decisions, reducing component count in industrial controls, monitoring equipment, and embedded systems. Key characteristics include very low supply current of 0.4 mA typical, 1 mW power consumption per comparator at a 5 V supply, low typical input bias current of 25 nA, and typical input offset current of ±5 nA. The typical input offset voltage is ±1 mV. Rail-to-rail input capability allows each comparator to operate with inputs near the negative and positive supply limits, while the open-collector outputs require an external pull-up resistor. The LM293DT uses a bipolar comparator architecture optimized for low power rather than high-speed operation. Its low input currents are useful when the source impedance is high or leakage would otherwise shift the comparison threshold. Because the outputs are open collector, two or more outputs can share a pull-up node to form a wired-AND function. The external pull-up determines output rise time, so resistance and capacitance must be selected together for the required switching speed. Typical applications include battery-powered threshold detection, sensor-signal conditioning, window comparators, overvoltage monitoring, industrial control interfaces, and simple switching regulators. The dual configuration is particularly useful when a system must monitor two independent limits or compare a measurement against both an upper and lower reference. For reliable PCB operation, place input and output bypass capacitors close to their associated pins and route comparator inputs away from switching nodes and high-current return paths. Account for input offset voltage and common-mode limits when defining detection thresholds. The open-collector outputs must always have a pull-up unless the output is intentionally left unconnected. This product page combines operating characteristics, application guidance, package information, and same-footprint replacement context to support faster component selection and board-level implementation.

RFQ Kontak