Mga Produkto (46,000+)

LM293H - Dual Differential Comparator | Texas Instruments
LM293H

LM293H - Dual Differential Comparator | Texas Instruments

The Texas Instruments LM293H is a dual differential comparator, an analog comparator IC with two independent comparison channels, open-collector outputs, and a TO-99-8 metal can package. The verified product data identifies the device as a general-purpose, low-power comparator with low offset voltage, operating from single or dual supplies over a wide voltage range. The LM293H is suitable when two signals must be compared and the result must drive TTL, MOS, CMOS, or other digital logic through its open-collector output. A differential comparator is a semiconductor device that compares two input voltages and produces a logic-level indication of their relationship. The dual-channel architecture provides two independent comparators in one package, reducing component count in threshold detection, overvoltage indication, current sensing, and control systems. Its open-collector outputs require an external pull-up resistor when the output must settle to a valid high level. The LM293 family is associated with wide supply capability, single-supply operation, and compatibility with common logic families. The LM293H is identified in the verified distributor data as an 8-pin TO-99-8 device with two channels. The manufacturer family information describes the LM293 as an industrial-grade dual differential comparator. The verified search data specifically lists low power, low offset voltage, rail-to-rail input labeling, open-collector output, and a wide supply operating range. Detailed electrical limits, propagation-delay curves, input common-mode limits, output sink-current limits, and temperature limits must be confirmed in the manufacturer datasheet before final design release. Typical uses include battery-powered monitoring, industrial sensor interfaces, overvoltage detection, temperature threshold circuits, and dual-rail control logic. In a practical design, each comparator can monitor a signal against a reference voltage while the open-collector output drives a pull-up and the downstream logic input. Care is required when inputs approach supply rails, when output pull-up speed affects timing, or when unused comparator channels are left unconnected. This page combines verified manufacturer and distributor links, package identification, application guidance, and structured comparison information. It intentionally avoids filling unavailable electrical values with guesses; consult the current manufacturer datasheet for authoritative limits, ordering details, and lifecycle information.

RFQ Kontak
LM293N - Dual Open-Collector Comparator, 8-DIP | STMicroelectronics
LM293N

LM293N - Dual Open-Collector Comparator, 8-DIP | STMicroelectronics

The STMicroelectronics LM293N is a dual, general-purpose voltage comparator with two independent channels, open-collector outputs, and an 8-DIP package. According to the STMicroelectronics LM293N product description, it is designed for single-supply operation across a wide voltage range, while operation from split power supplies is also possible. The verified distributor listing identifies the device as an 8-DIP comparator with open-collector/open-drain, rail-to-rail characteristics. Specific voltage, current, timing, temperature, and logic-threshold values were not included in the provided data and therefore require verification from the manufacturer datasheet before design release. A voltage comparator is an analog semiconductor that compares two input voltages and produces a logic-level indication of their relationship. The LM293N contains two independent comparators, allowing one package to implement threshold detection, window comparison, free-running oscillator, or simple analog-to-logic conversion. Within the broader hierarchy, it is a comparator IC, then an analog integrated circuit, and finally a semiconductor. Its open-collector outputs can sink external current and normally require a pull-up resistor when the design expects a high-level output. The primary documented feature is its ability to operate from a single supply over a wide range of voltages, with split-supply operation also supported. The two independent channels provide design flexibility for comparing a sensor against a reference, checking a power rail, or generating complementary decisions in control circuitry. The open-collector architecture can support wired logic and level translation, but the external pull-up, output current, propagation delay, and input common-mode limits must be checked against the actual datasheet. LM293N is suitable for industrial control, instrumentation, power-supply supervision, sensor interfaces, and embedded threshold detection. In a single-supply circuit, place the input network so that the signal remains within the device's verified common-mode range. In a split-supply circuit, confirm the positive and negative rail limits and the permitted total voltage. Because the provided data does not state absolute maximum ratings, supply voltage, input offset, output-current capability, response time, or operating temperature, those values should not be assumed. Design practice should include a local bypass capacitor, a defined pull-up resistor for each open-collector output, and protection for exposed sensor inputs. Avoid relying on an output high level until the pull-up network and downstream load have been analyzed. Verify input polarity, output inversion, hysteresis, and logic compatibility with the system controller. The 8-DIP package is mechanically important: use the manufacturer pinout and maintain adequate lead spacing during assembly. This page combines the verified LM293N product identity, package information, application context, datasheet links, and engineering considerations. It intentionally does not fabricate electrical ratings, pricing, lifecycle claims, or unreported pin names; obtain the current manufacturer datasheet and distributor quotation for production decisions.

RFQ Kontak
LM293P - Dual 36V Differential Comparator | Texas Instruments
LM293P

LM293P - Dual 36V Differential Comparator | Texas Instruments

Texas Instruments LM293P is a dual differential comparator rated for a 2 V to 36 V supply range, with a stated propagation delay of 300 ns, packaged as an 8-pin PDIP. Each channel provides independent differential inputs and an open-collector output, making the device suitable for threshold detection, level translation, relay driving, and industrial control logic. A differential comparator is an analog integrated circuit that compares two input voltages and changes its output state according to their relative polarity. The LM293 belongs to the comparator hierarchy, which sits within linear and mixed-signal ICs. Its open-collector outputs can sink current from a pull-up network, allowing the outputs to be wired together when wired-OR operation is required. The principal features of the LM293P are its dual-channel architecture, differential input arrangement, wide 2 V to 36 V operating supply range, open-collector outputs, and 300 ns response time. The package is an 8-pin PDIP, providing a through-hole footprint suitable for prototypes, legacy industrial equipment, repair assemblies, and applications where leaded components are preferred. The LM293 contains two electrically independent comparator channels. Differential inputs are presented through inverting and non-inverting pins, while the output uses an open-collector transistor capable of pulling the output node toward ground. A pull-up resistor is required to establish a high output level, and the output stage can sink current from TTL, CMOS, and other logic families within the device's stated operating limits. Typical uses include monitoring a control or battery voltage against a reference, detecting sensor crossings, implementing overvoltage and undervoltage protection, driving relay or indicator circuits, and providing threshold-compatible interfaces between analog and digital systems. Because the device supports a wide supply range, it can also be used in industrial systems operating from conventional low-voltage DC rails. Designers must provide the required output pull-up and verify input common-mode limits, output-current limits, and operating temperature against the manufacturer datasheet. Input protection, bypassing, and leaded-component spacing should also be considered when the LM293P is used in high-noise or high-voltage surroundings. This page combines verified manufacturer and distributor information with package-level selection guidance, verified drop-in candidates, application use cases, and practical design notes. It is intended to help engineers identify whether the LM293P fits an existing 8-pin comparator design without confusing electrically related but mechanically different packages.

RFQ Kontak
LM293QT - Dual Low-Power Wide-Supply Comparator | STMicroelectronics
LM293QT

LM293QT - Dual Low-Power Wide-Supply Comparator | STMicroelectronics

The STMicroelectronics LM293QT is a dual general-purpose comparator designed for low-power operation from a single supply or split supplies. The device provides two independent comparator channels, a wide single-supply operating range of 2 V to 36 V, and an open-collector output configuration. It is packaged in an 8-UFDFN package with a 2 mm x 2 mm body size. The LM293QT is suited to voltage-level detection, threshold comparison, industrial control logic, sensor interfaces, and low-current signal conditioning where a compact, low-power comparator is required. An analog comparator is an integrated circuit that evaluates two input voltages and changes its output state when the voltage at the non-inverting input becomes higher than the voltage at the inverting input. The LM293 family belongs to the comparator and linear IC hierarchy, where each independent channel compares its differential input while operating from a common supply. This makes the device useful between sensors and digital control systems, where a small voltage difference must be converted into a logic-compatible indication. The principal electrical characteristics include a 2 V to 36 V single-supply range, operation from split supplies of plus or minus 1 V to plus or minus 18 V, and very low supply current of approximately 0.45 mA. The comparator channels feature low input bias current of approximately 20 nA. The open-collector output stage allows the output to be pulled up to an external supply and enables wired-AND behavior when multiple comparator outputs are connected. The output type is suitable for interfacing with open-drain or open-collector digital devices. The LM293QT provides two independent channels in a compact 8-UFDFN package. The wide supply range allows operation from low-voltage systems through higher industrial rails, while the low supply current supports battery-operated and always-on equipment. The two channels can be used for independent threshold decisions, window monitoring, or complementary comparisons. Open-collector outputs require an external pull-up resistor when the output must rise to a defined logic-high voltage. Typical applications include industrial sensor interfaces, battery monitoring, power-supply sequencing, overvoltage and undervoltage detection, temperature-controller signal conditioning, and embedded threshold logic. Because the input common-mode range can include ground, the LM293QT is particularly useful in systems where the signal being monitored is close to the negative supply rail. When laying out a design, preserve the exposed-pad and package thermal requirements of the 8-UFDFN package. Route the comparator inputs away from switching nodes and high-current output paths, and place the input and output components close to their associated pins. Choose the external pull-up voltage and resistor to match the receiving logic, and verify that the output sink current remains within the device limits for the selected pull-up network.

RFQ Kontak
LM293ST - Dual 2V-36V Comparator | STMicroelectronics
LM293ST

LM293ST - Dual 2V-36V Comparator | STMicroelectronics

The STMicroelectronics LM293ST is a dual differential voltage comparator designed for low-voltage operation, with a 2 V to 36 V supply range and open-collector, open-drain outputs. The device contains two independent comparator channels in an 8-pin MiniSO surface-mount package, allowing both channels to operate from the same supply or from split power rails. A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level output indicating which input is higher. The LM293 family belongs to the comparator and amplifier IC category within the broader semiconductor hierarchy. Its open-collector outputs can sink current while remaining in a high-impedance state, making the device suitable for wired logic, pull-up resistor networks, relay drivers, and systems that require a flexible output drive configuration. The LM293ST provides two independent comparators, low offset, and high precision according to the STMicroelectronics LM293 family information. Its rail-to-rail input operation allows each differential input to approach the supply rails, which is useful when monitoring low-voltage sensor signals or battery-powered thresholds. The open-collector outputs also provide a deliberate isolation between the comparator output and the supply voltage, permitting external pull-up selection for a different logic family. Both channels can operate from a single 2 V to 36 V supply, and the device also supports split power-supply arrangements. The low-power architecture is intended for general-purpose threshold detection rather than high-speed signal conditioning. Because the outputs are open collector, designers must add pull-up resistors when a continuously driven high level is required. The output transistor provides current sinking capability, while the external pull-up establishes the high-state voltage and limits the available rise rate. Typical applications include industrial sensor thresholding, overvoltage and undervoltage detection, battery monitoring, window-comparator circuits, control-loop signaling, and digital interface adaptation. Two channels can also implement a hysteretic switching controller, an automatic window detector, or a pair of independent limit alarms. In each case, input and output implementation details should be checked against the operating voltage, common-mode range, load current, and logic requirements of the completed circuit. The principal design consideration is that an open-collector output is not a push-pull logic output. Select the pull-up resistor and logic voltage carefully, keep the pull-up current within the output sink-current rating, and place the device close enough to the protected signal path to minimize pickup of switching noise. The exposed package also requires attention to copper area and thermal conditions when either channel operates continuously at maximum load. This product page brings together the manufacturer family information, distributor listing attributes, package details, replacement guidance, and practical design considerations. It also distinguishes verified electrical attributes from parameters that require confirmation from the LM293 manufacturer datasheet, helping engineers plan a replacement or design-in without relying on package-code assumptions.

RFQ Kontak
LM321MF/NOPB - 1MHz, Single Op Amp, 3-32V, SOT-23-5 | TI
LM321MF/NOPB

LM321MF/NOPB - 1MHz, Single Op Amp, 3-32V, SOT-23-5 | TI

The Texas Instruments LM321MF/NOPB is a single-channel, low-power operational amplifier delivering 1 MHz unity-gain bandwidth and 0.4 V/us slew rate in a 5-pin SOT-23 (DBV) package. It operates from a single 3 V to 32 V supply (or dual +/-1.5 V to +/-16 V) and supports an input common-mode range that includes ground, enabling true single-supply operation. Housed in the industry-standard SOT-23-5 footprint, the LM321MF/NOPB combines economy with TI's LM321 bipolar architecture originally developed by National Semiconductor. An operational amplifier (op amp) is a high-gain DC-coupled electronic voltage amplifier with differential inputs and a single-ended output. Op amps belong to the amplifier IC family within integrated circuits, which also includes instrumentation amplifiers, comparators, and specialty audio/video amplifiers. The LM321MF/NOPB specifically is a general-purpose single op amp, meaning one amplifier channel per package; it sits in the hierarchy: op amp -> amplifier IC -> analog IC -> integrated circuit -> semiconductor. Key features include 1 MHz gain-bandwidth product, 0.4 V/us slew rate, low input offset voltage (typical 2 mV), input common-mode range that includes the negative rail, and large capacitive-load drive capability. The bipolar input stage with class-AB output provides robust performance across the wide 3 V to 32 V supply range. Internal ESD protection and thermal shutdown enhance field reliability. The LM321MF/NOPB uses a bipolar transistor input stage rather than CMOS or JFET, giving it inherently low noise voltage density but somewhat higher input bias current than modern CMOS alternatives. Its wide supply range allows direct connection to industrial 24 V rails, 12 V battery systems, or +/-15 V analog supplies, eliminating the need for additional level shifters. The 1 MHz bandwidth is sufficient for audio, sensor conditioning, and many active-filter topologies. Typical applications include transducer signal conditioning, low-frequency active filters, current sensing with high-side or low-side shunt, audio pre-amplifier stages, and general-purpose amplification in industrial controls. The SOT-23-5 footprint is ideal for space-constrained PCB designs such as handheld instruments and IoT sensor modules. When designing with the LM321MF/NOPB, verify input bias current (45 nA typical) is acceptable for high-impedance sensor interfaces. Place a 0.1 uF decoupling capacitor close to the VCC pin and ensure output capacitive loads stay within the datasheet's stability region to avoid oscillation. This page synthesizes distributor pricing, drop-in SOT-23-5 alternatives, and practical design notes not found in the manufacturer datasheet alone, giving engineers a faster path from datasheet to prototype.

RFQ Kontak
LM324AD - Quad 30V 1.2MHz Op Amp | Texas Instruments
LM324AD

LM324AD - Quad 30V 1.2MHz Op Amp | Texas Instruments

Texas Instruments LM324AD is a general-purpose quad operational amplifier containing four independent, internally frequency-compensated amplifiers. The device supports a 30 V maximum supply, operates at a gain-bandwidth product of 1.2 MHz, and has a 3 mV input offset voltage rating. It is supplied in a 14-pin SOIC package, enabling one component to provide four amplified channels in a compact surface-mount footprint. The LM324 family is designed for single-supply operation over a wide voltage range, while also supporting split-supply arrangements when the circuit requires a bipolar input or output range. An operational amplifier is an analog signal-processing IC that uses high-gain differential amplification to increase the voltage presented at its input. The LM324 belongs to the general-purpose amplifier segment of the larger voltage-feedback operational-amplifier hierarchy. Internally compensated amplifiers simplify closed-loop design because no external frequency-compensation components are required for ordinary gain configurations. Four independent amplifiers in one package reduce board area and component count in multi-channel sensor, filtering, buffering, and control circuits. The verified product information identifies four amplifier circuits, a 1.2 MHz gain-bandwidth product, a 3 mV offset-voltage rating, and operation from a supply as high as 30 V. The internal compensation supports stable operation in standard noninverting and inverting amplifier arrangements. Because the LM324AD is a general-purpose device, design engineers should treat it as a cost-conscious solution rather than a precision op amp with rail-to-rail outputs, low offset over temperature, or very low noise. Common uses include buffering sensor outputs, amplifying low-level control signals, active filtering, differential signal conditioning, and driving ADC input stages. The four independent channels can process separate analog signals or implement stages such as a two-stage filter or transimpedance-style front end. Single-supply operation is particularly useful in industrial controls, embedded instrumentation, educational electronics, and simple battery-powered systems where a negative rail is unavailable. When using the LM324AD, verify input and output common-mode limits, output-current capability, load impedance, and stability under the selected closed-loop gain before finalizing the design. Place input and output compensation or decoupling components close to the relevant pins, keep sensitive input routing away from switching nodes, and include adequate bypassing on the power supply. The 14-pin SOIC package also requires attention to thermal pad-free layout and copper continuity when operating at high ambient temperatures. This product page combines verified manufacturer and distributor information, lifecycle-oriented sourcing details, same-footprint alternatives, and practical design guidance. It adds a same-package comparison framework and implementation notes that are more useful for PCB and sourcing decisions than a distributor listing alone.

RFQ Kontak
LM324ADBR - 30V 1.2MHz Quad Op Amp | Texas Instruments
LM324ADBR

LM324ADBR - 30V 1.2MHz Quad Op Amp | Texas Instruments

The Texas Instruments LM324ADBR is a four-circuit general-purpose operational amplifier rated for a 30 V maximum supply, 1.2 MHz gain-bandwidth product, and 3 mV input offset voltage. The device is packaged in a 14-pin SSOP (DB) package and is intended for low-frequency signal conditioning, current-to-voltage conversion, and general amplifier applications operating from a single or dual supply. An operational amplifier is a high-gain differential amplifier whose closed-loop behavior is established primarily by external feedback components. The LM324A family combines four amplifiers in one package, placing it in the operational-amplifier hierarchy alongside instrumentation, buffer, and comparator circuits while remaining part of the broader analog and power-management semiconductor ecosystem. Its common-mode input range allows the device to operate from single-supply or split-supply systems. The LM324ADBR supports a 3 V to 32 V total supply range, has an approximately 1.2 MHz gain-bandwidth product, and specifies a maximum input offset voltage of 3 mV. The package operates from 0°C to 70°C, making the standard A-grade ordering option suitable for commercial and industrial equipment where extended-temperature operation is not required. Its four independent channels can implement non-inverting, inverting, summing, difference, and comparator functions. Each channel uses a bipolar transistor input stage and an internally compensated architecture. Internal compensation removes the need for an external frequency-compensation capacitor in ordinary closed-loop operation. The 65 dB common-mode rejection and 16 V output swing support precision conditioning of mid-level signals, while the 60 mA per-channel output-current capability provides useful drive for higher-impedance loads. Typical uses include sensor signal conditioning, low-side current measurement, audio preamplification, transducer interfaces, and general DC signal amplification. The quad configuration also allows a single package to implement a complete instrumentation channel, such as a two-op-amp differential stage plus two buffer or gain stages. The device is especially suitable where a supply voltage above 5 V is available but a rail-to-rail input or output is unnecessary. Designers should verify common-mode input and output swing against the actual signal range, provide adequate bypassing close to the supply pins, and account for input offset and bias currents in high-impedance measurements. A stable feedback network and adequate output-load capability are also important because the LM324A is optimized for general-purpose, low-frequency precision rather than high-speed or rail-to-rail performance. This product page combines the Texas Instruments ordering information, package and electrical characteristics, sourcing guidance, and practical design considerations into a focused engineering reference. It also identifies same-footprint family options and explains the trade-offs when comparing the LM324A with lower-cost or lower-performance amplifier implementations.

RFQ Kontak
LM324ADE4 - Quad 1.2MHz Op Amp | Texas Instruments | SOIC-14
LM324ADE4

LM324ADE4 - Quad 1.2MHz Op Amp | Texas Instruments | SOIC-14

Texas Instruments LM324ADE4 is a quad general-purpose operational amplifier with four independent, internally frequency-compensated amplifiers, 1.2 MHz gain-bandwidth product, and 0.5 V/µs slew rate in a 14-pin SOIC package. The device operates from a single supply or split supplies, with the listed operating range extending to ±16 V. An operational amplifier is an analog signal-conditioning IC that compares two input voltages and amplifies their difference through high open-loop gain. The LM324ADE4 belongs to the operational-amplifier hierarchy within amplifier ICs and analog semiconductors. Its four independent channels allow one package to provide feedback control, buffering, level shifting, summation, and general analog amplification without requiring four separate amplifier packages. The four amplifiers feature internally frequency compensation, allowing operation as stable unity-gain buffers without external compensation components. A 1.2 MHz gain-bandwidth product and 0.5 V/µs slew rate support audio-band and general-purpose closed-loop applications. The device also supports operation from a single positive supply as well as split bipolar supplies, making it useful in mixed industrial, instrumentation, control, and consumer circuits. The 14-SOIC package is pin-compatible with the established LM324 family arrangement, which simplifies repair, prototyping, and board reuse. Each amplifier has differential inputs, an output, and power connections, with the package distributing those functions across four channels. Because the amplifiers are independent rather than sharing internal output stages, each channel can be used for a separate signal path or left unused when its input and output are properly configured. Typical uses include sensor-signal conditioning, low-current motor and actuator drivers, audio preamplification, analog summing networks, threshold detection, and general instrumentation. The 1.2 MHz bandwidth is adequate for many audio and control signals, but designs requiring substantially higher bandwidth, lower offset voltage, faster settling, or lower noise should use a more specialized amplifier family. Design carefully around input common-mode range, output swing, input bias current, and the limits of each amplifier channel. Keep sensitive inputs away from noisy return paths, observe the recommended bypass capacitors at the supply pins, and avoid operating near the output saturation limits. The manufacturer datasheet should guide input/output protection, supply decoupling, unused-channel configuration, and maximum input and output voltage conditions. This product page combines the LM324ADE4 operating parameters, package details, practical application guidance, pin-focused design considerations, and qualified drop-in alternatives. It is intended to help engineers identify where this economical quad general-purpose amplifier fits and where a higher-performance or application-specific amplifier is more appropriate.

RFQ Kontak
LM324ADG - Quad Op-Amp 1MHz 0.6V/us SOIC-14 | onsemi
LM324ADG

LM324ADG - Quad Op-Amp 1MHz 0.6V/us SOIC-14 | onsemi

The onsemi LM324ADG is a low-cost, single-supply quad operational amplifier with four independent, high-gain, internally frequency-compensated amplifiers in a 14-pin SOIC (3.90 mm width) package. It operates from a single 3 V to 32 V supply (or dual supplies of ±1.5 V to ±16 V), delivers a 1 MHz gain-bandwidth product and a 0.6 V/us slew rate, and draws quiescent current roughly one-fifth of that of comparable standard op amps. An operational amplifier is a high-gain voltage amplifier with differential inputs and a single-ended output, the foundational building block of the analog signal chain. Within the amplifier hierarchy, the LM324ADG belongs to the general-purpose, single-supply op-amp family, sitting above specialized precision, high-speed, and rail-to-rail amplifiers and below discrete transistor front ends in complexity. Quad op amps integrate four amplifiers on one die, sharing bias circuitry to save board space, cost, and power versus four single amplifiers. Key features include true differential inputs valid at ground (the common-mode input range extends to the negative rail, an LM324 family signature), a wide supply range from 3.0 V to 32 V that covers 5 V, 12 V, 15 V, and 24 V rails, four amplifiers per package for dense multi-channel analog designs, and internally compensated unity-gain stability that removes the need for external frequency-compensation capacitors. Architecturally, the LM324A uses bipolar NPN input stages with PNP common-emitter amplifiers and Class AB outputs. The 'A' grade tightens the input offset voltage specification to a 3 mV maximum. Because the output stage is not rail-to-rail, the output swings to within roughly 1.5 V of V+ at light load while reaching close to the negative rail - a characteristic engineers must budget for when using the full supply range. Typical applications include transducer signal conditioning, DC gain blocks, active filters, comparators with hysteresis, summing amplifiers, and multi-channel industrial sensor interfaces, where the single-supply ground-sensing input and four-amplifier density directly reduce component count. Design consideration: the common-mode input range stops about 1.5 V below the positive rail, so keep input signals at least that far from V+ to avoid phase inversion or distortion. This page adds value beyond the manufacturer datasheet by consolidating drop-in alternatives, parameter comparison tables, and practical design notes in one place for sourcing and design engineers.

RFQ Kontak
LM324ADR - Quad 30V 1.2MHz Op Amp | Texas Instruments (Tape & Reel)
LM324ADR

LM324ADR - Quad 30V 1.2MHz Op Amp | Texas Instruments (Tape & Reel)

Texas Instruments LM324ADR is a general-purpose quad operational amplifier containing four independent, internally frequency-compensated amplifiers. The device supports a 30 V maximum supply, operates at a gain-bandwidth product of 1.2 MHz, and has a 3 mV input offset voltage rating. It is supplied in a 14-pin SOIC package, enabling one component to provide four amplified channels in a compact surface-mount footprint. The LM324 family is designed for single-supply operation over a wide voltage range, while also supporting split-supply arrangements when the circuit requires a bipolar input or output range. An operational amplifier is an analog signal-processing IC that uses high-gain differential amplification to increase the voltage presented at its input. The LM324 belongs to the general-purpose amplifier segment of the larger voltage-feedback operational-amplifier hierarchy. Internally compensated amplifiers simplify closed-loop design because no external frequency-compensation components are required for ordinary gain configurations. Four independent amplifiers in one package reduce board area and component count in multi-channel sensor, filtering, buffering, and control circuits. The verified product information identifies four amplifier circuits, a 1.2 MHz gain-bandwidth product, a 3 mV offset-voltage rating, and operation from a supply as high as 30 V. The internal compensation supports stable operation in standard noninverting and inverting amplifier arrangements. Because the LM324ADR is a general-purpose device, design engineers should treat it as a cost-conscious solution rather than a precision op amp with rail-to-rail outputs, low offset over temperature, or very low noise. Common uses include buffering sensor outputs, amplifying low-level control signals, active filtering, differential signal conditioning, and driving ADC input stages. The four independent channels can process separate analog signals or implement stages such as a two-stage filter or transimpedance-style front end. Single-supply operation is particularly useful in industrial controls, embedded instrumentation, educational electronics, and simple battery-powered systems where a negative rail is unavailable. When using the LM324ADR, verify input and output common-mode limits, output-current capability, load impedance, and stability under the selected closed-loop gain before finalizing the design. Place input and output compensation or decoupling components close to the relevant pins, keep sensitive input routing away from switching nodes, and include adequate bypassing on the power supply. The 14-pin SOIC package also requires attention to thermal pad-free layout and copper continuity when operating at high ambient temperatures. This product page combines verified manufacturer and distributor information, lifecycle-oriented sourcing details, same-footprint alternatives, and practical design guidance. It adds a same-package comparison framework and implementation notes that are more useful for PCB and sourcing decisions than a distributor listing alone.

RFQ Kontak
LM324ADR2 - 3-32V Quad 1MHz Op Amp | onsemi
LM324ADR2

LM324ADR2 - 3-32V Quad 1MHz Op Amp | onsemi

The onsemi LM324ADR2 is a general-purpose, single-supply quad operational amplifier with four amplifier circuits, a 3 V to 32 V supply range, 1 MHz gain-bandwidth product, and a maximum input offset voltage of 3 mV, housed in a 14-pin SOIC package. The device supports true differential inputs and combines four amplifiers in one package, reducing board area in cost-sensitive analog signal-conditioning systems. An operational amplifier is an amplifier IC that uses high open-loop gain and negative feedback to amplify the difference between two input voltages. The quad configuration places four amplifiers in one device, making it widely used in general-purpose signal conditioning, sensor interfaces, filtering, and control systems. Within the electronics hierarchy, an operational amplifier is a linear amplifier IC and a building block for analog signal-processing circuits. Key characteristics include four amplifier sections, operation from 3 V to 32 V, a 1 MHz gain-bandwidth product, and a 3 mV maximum input offset voltage. The wide supply-voltage range allows the LM324ADR2 to operate from common low-voltage supplies as well as higher-voltage industrial rails. Its internal input-stage characteristics are designed for general-purpose applications rather than high-speed precision signal paths. The quad architecture consolidates four amplifiers into one 14-pin SOIC package. This can simplify PCB layouts and reduce component count in designs requiring several independent analog channels. Because all four sections share one package and supply connection, engineers must still consider common supply-current variation, thermal behavior, ground routing, and channel-to-channel performance when planning precision measurements. Typical uses include low-frequency sensor amplification, audio preamplification, DC signal conditioning, active filtering, voltage comparison, and industrial control interfaces. The 1 MHz gain-bandwidth product is appropriate for signals well below its upper bandwidth limit, while the 3-32 V operating range supports both compact low-voltage systems and higher-voltage industrial electronics. For reliable layout, route analog inputs and feedback connections away from switching-current paths, connect the ground reference properly, and place input and output bypass capacitors close to the device. Avoid using the LM324ADR2 where very low offset, very low bias current, rail-to-rail output swing, or high-speed closed-loop performance is required without first checking the full operating conditions. This page organizes the LM324ADR2 electrical characteristics, package information, drop-in candidates, application guidance, and design notes into a practical engineering reference for analog designers.

RFQ Kontak
LM324ADR2G - Quad Op Amp, 3-32V, 1MHz SOIC-14 | onsemi
LM324ADR2G

LM324ADR2G - Quad Op Amp, 3-32V, 1MHz SOIC-14 | onsemi

The onsemi LM324ADR2G is a low-cost quad operational amplifier with four independent general-purpose amplifier circuits, true differential inputs, a supply range of 3V to 32V single-supply (or ±1.5V to ±16V split supply), a 1 MHz gain-bandwidth product, and a 0.6 V/µs slew rate, housed in a 14-pin SOIC package supplied on tape and reel. A quad operational amplifier is an integrated circuit that packs four identical, frequency-compensated op amp stages onto a single silicon die, sharing one set of power pins. Within the amplifier hierarchy, it belongs to the general-purpose bipolar op amp family: operational amplifier -> linear amplifier IC -> analog signal conditioning IC. Quad op amps reduce board area, cut per-channel cost, and improve channel-to-channel thermal matching versus four single op amps. Key features include single-supply operation down to 3V with input common-mode range that includes ground - the defining trait that made the LM324 the industry-standard quad op amp. The A-grade suffix guarantees a maximum input offset voltage of 3 mV, tighter than the base LM324. Internally frequency compensation eliminates external compensation components, and the low supply current of approximately 700 µA per amplifier (typical for the family) suits battery-powered designs. Technically, the LM324ADR2G uses a mature bipolar process with PNP input stages that enable ground-sensing inputs. The output stage is a classic single-ended Class-AB emitter follower, which means it can sink only limited current near ground and exhibits output crossover behavior under light loads - a known characteristic designers must account for in precision or audio paths. Typical applications include transducer signal conditioning, DC gain blocks, active filters, comparators, voltage followers, and industrial sensor interfaces where single-supply, ground-referenced inputs simplify the power architecture. Design consideration: keep total supply voltage within 32V, and remember the output cannot swing rail-to-rail - headroom of roughly 1.5V to the positive rail is required at moderate loads. This page adds value beyond the manufacturer datasheet by synthesizing distributor pricing, verified drop-in alternatives, a parametric comparison table, and practical design notes in one place.

RFQ Kontak
LM324ADRE4 - Quad 1.2MHz Op Amp in 14-SOIC | Texas Instruments
LM324ADRE4

LM324ADRE4 - Quad 1.2MHz Op Amp in 14-SOIC | Texas Instruments

Texas Instruments LM324ADRE4 is a quadruple general-purpose operational amplifier with four independent amplifier channels, a 1.2 MHz gain-bandwidth product, and a 0.5 V/us slew rate. The device operates from ±1.5 V to ±16 V and is packaged in a 14-pin SOIC. An operational amplifier is an analog signal-conditioning semiconductor that amplifies the difference between its inverting and non-inverting inputs. The LM324 belongs to the general-purpose op-amp hierarchy, combining four amplifiers in one integrated circuit. This integration reduces board area and simplifies designs requiring multiple low-frequency signal channels, such as sensor conditioning, audio paths, data acquisition, and industrial control loops. Each channel supports single-supply or dual-supply operation. Key characteristics include a 1.2 MHz gain-bandwidth product, 0.5 V/us slew rate, and a supply-voltage range of ±1.5 V to ±16 V. The four-channel architecture makes the device useful for amplifier arrays, active filters, comparators, buffer stages, and transducer interfaces. The 14-pin SOIC is a standard surface-mount package suitable for conventional PCB assembly and rework. The LM324ADRE4 is designed for general-purpose applications where a wide bandwidth, adequate slew rate, and economical quad integration are more important than low offset voltage, rail-to-rail output, or high precision. Its 14-pin package provides one amplifier section per three-and-a-half pins, with the positive supply connected to pin 4 and the negative supply connected to pin 11 in the standard dual-supply configuration. Grounding the negative supply pin permits single-supply operation when the signal and output remain within the usable common-mode range. Typical uses include low-frequency audio amplification, sensor signal conditioning, active filter stages, voltage followers, comparators, and general instrumentation. In multi-stage designs, the four channels can implement cascaded gain, summing, difference, or buffering functions while reducing component count. Independent amplifier sections also allow unused channels to be configured conservatively rather than left floating. Layout should keep feedback resistors and input traces close to the device, maintain short return paths to the supply ground, and place input bypass capacitance near the supply pins. Check output-current and capacitive-load limits for the selected operating condition. Because the LM324 is a general-purpose amplifier rather than a precision or rail-to-rail part, verify input common-mode range, output swing, offset, and noise requirements against the actual signal. This page combines the manufacturer-family specifications with same-package alternatives, a parameter comparison, and practical PCB guidance. It is designed to support quick part selection while directing engineers to the manufacturer datasheet and pin-description table for final circuit qualification.

RFQ Kontak
LM324ADRG4 - 1.2MHz Quad Op Amp, 14-SOIC | Texas Instruments
LM324ADRG4

LM324ADRG4 - 1.2MHz Quad Op Amp, 14-SOIC | Texas Instruments

Texas Instruments LM324ADRG4 is a standard general-purpose, four-circuit operational amplifier in a 14-pin SOIC package. Each circuit has a 1.2 MHz gain-bandwidth product, 0.5 V/us slew rate, and operation from single or split supplies over a ±1.5 V to ±16 V range. The four amplifiers are independent, high-gain, frequency-compensated stages designed for general-purpose signal conditioning. An operational amplifier is an amplifier IC used within a feedback network to control gain, amplify differential signals, buffer inputs, perform comparisons, or drive analog stages. The LM324 belongs to the operational-amplifier hierarchy, which includes amplifier ICs, analog signal-chain ICs, and semiconductor devices. Its ability to operate from a single supply makes it useful in battery-powered, industrial-control, instrumentation, and consumer circuits where one supply rail is more practical than split bipolar rails. The LM324 family's key characteristics include a typical supply-current drain of 0.8 mA and a common-mode input-voltage range that includes ground. These characteristics support low-power analog designs where the input signal may approach the lower supply rail. Each amplifier is frequency compensated, reducing the external compensation components normally required in precision applications. The 1.2 MHz bandwidth is sufficient for general-purpose audio, control, sensing, and signal-shaping stages but is not intended for high-speed data acquisition or demanding wideband filtering. Typical uses include current sensing around a low-side shunt, low-side transistor control, sensor amplification, audio channels, and general-purpose buffering. The 14-SOIC package provides a conventional through-hole-compatible footprint for PCB assembly. Because each of the four amplifier sections is independent, unused sections should be configured according to the manufacturer's recommended practice rather than left floating. A key design consideration is the input common-mode range. The LM324 can accept inputs that include ground, making it suitable for many single-supply circuits, but it cannot swing all the way to the positive supply rail. Output swing, load capability, and input bias behavior must therefore be checked against the actual signal range. Decoupling should follow the manufacturer circuit recommendations, with short supply traces and a local bypass capacitor helping maintain stable operation. This product record combines the verified LM324ADRG4 electrical ratings, package information, sourcing links, pin-compatible family options, and practical design guidance. It also distinguishes true same-footprint alternatives from related amplifier families that differ in electrical behavior, qualification, package, or pin assignment.

RFQ Kontak
LM324ADTB - Quad 3-32V General-Purpose Op Amp | onsemi
LM324ADTB

LM324ADTB - Quad 3-32V General-Purpose Op Amp | onsemi

onsemi LM324ADTB is a low-cost, general-purpose quad operational amplifier with true differential inputs, four amplifier circuits, a 3 V to 32 V supply range, and 3 mV input offset voltage in a 14-pin TSSOP package. The device is designed for instrumentation, buffer-amplifier, and general signal-conditioning applications where four amplifiers are integrated in one package. An operational amplifier is an analog integrated circuit that uses high-gain differential feedback to amplify the voltage difference between its two inputs. The LM324 belongs to the quad operational amplifier hierarchy: operational amplifier, voltage-feedback amplifier, analog signal-conditioning IC, and power-management IC. Its four independent channels can perform amplification, buffering, summing, comparison, and basic active-filter functions without requiring four separate packages. The LM324ADTB supports single-supply operation from 3 V to 32 V, making it suitable for systems whose rails are higher than those of common rail-to-rail precision amplifiers. Its 3 mV input offset voltage supports general-purpose applications where input accuracy requirements are moderate. True differential inputs allow each channel to respond to the difference between its inverting and non-inverting signals. The integrated quad configuration also reduces board area and simplifies multi-channel routing. As a general-purpose amplifier, the LM324 series emphasizes practical utility rather than high speed or precision. The manufacturer describes the devices as low-cost quad operational amplifiers that are especially useful in single-supply systems. Their quiescent current is approximately one-fifth that of conventional dual operational amplifiers, according to the manufacturer datasheet. Detailed gain-bandwidth, slew-rate, input-bias-current, and common-mode limits must be checked against the operating conditions before precision filtering or signal-chain use. Typical applications include four-channel sensor conditioning, transducer buffering, audio preamplification, current-voltage conversion, DC signal amplification, and mixed-signal instrumentation. The 14-pin TSSOP package is useful for compact industrial, consumer, and communications equipment where four analog functions must be accommodated without using four separate amplifier packages. Supply bypassing and stable feedback layouts remain important at the board level. For a new design, place the device close to the powered circuits it serves and connect a suitable bypass capacitor near the supply pins. Keep feedback resistors and input traces short, maintain symmetrical routing where practical, and account for input bias-current errors when using high source impedances. The single supply must remain within the 3 V to 32 V operating range under all tolerance, transient, and temperature conditions. This page consolidates the LM324ADTB electrical ratings, package details, pin assignments, replacement options, and practical layout considerations into an engineering-focused reference. It also identifies where the general-purpose LM324 architecture is appropriate and where precision, speed, rail-to-rail operation, or a lower-offset amplifier would provide a better design choice.

RFQ Kontak
LM324ADTBG - 4-Channel 3-32V Op Amp | onsemi | TSSOP-14
LM324ADTBG

LM324ADTBG - 4-Channel 3-32V Op Amp | onsemi | TSSOP-14

The onsemi LM324ADTBG is a four-channel general-purpose operational amplifier designed for single-supply operation from 3 V to 32 V and packaged in a 14-pin TSSOP. Each amplifier provides true differential inputs, internal frequency compensation, and an approximately 1 MHz gain-bandwidth product, making the device suitable for low-cost signal conditioning, buffering, and analog control applications. An operational amplifier is an analog integrated circuit that uses high-gain differential amplification to increase the voltage difference between its two inputs. The quad operational-amplifier category groups four amplifiers in one package, reducing board area compared with four discrete single amplifiers. Within the broader hierarchy, the LM324 belongs to the amplifier IC and signal-chain categories, with applications spanning instrumentation, industrial control, sensor interfaces, and power-management circuits. Key characteristics include a 3 V to 32 V supply range, approximately 0.6 V/µs slew rate, 3 mV typical input-offset voltage, and 2 nA typical input-offset current. The device can operate with a single positive supply or split supplies, while its common-mode input range includes ground. These characteristics make it useful for battery-powered equipment and other low-voltage systems where the input signal may approach the lower supply rail. The four internal amplifiers use true differential input stages and are internally frequency compensated for unity-gain operation. The approximate 1 MHz gain-bandwidth product favors moderate-speed applications rather than precision signal paths demanding megahertz bandwidth or microvolt-level offset. Typical offset-current behavior supports high-impedance sensing, but source impedance must still be balanced to minimize offset and bias-current errors. Typical uses include current-to-voltage conversion in sensor interfaces, audio preamplification, comparator-style thresholding, active filtering, relay driving, and low-side current monitoring. The four amplifiers can also implement independent sensor channels, instrument loops, or gain stages where package size and cost matter more than precision or slew rate. When laying out the circuit, place input resistors close to the noninverting and inverting pins to reduce parasitic pickup, especially with high source impedance. Decoupling capacitors should be connected from each supply pin to ground with a short return path. Keep sensitive input traces away from switching nodes and provide adequate output-current headroom for capacitive loads because the LM324 is not rail-to-rail. This product guide combines package information, functional application guidance, selection criteria, and pin-compatible alternatives to simplify footprint planning and sourcing. For exact lead assignments, electrical limits, and ordering details, use the manufacturer datasheet and the technical information linked on this page.

RFQ Kontak
LM324ADTBR2 - Quad 3-26V Op Amp, 14-TSSOP | onsemi
LM324ADTBR2

LM324ADTBR2 - Quad 3-26V Op Amp, 14-TSSOP | onsemi

The onsemi LM324ADTBR2 is a low-cost quad operational amplifier with four true differential-input amplifiers in a 14-pin TSSOP package. The device operates from 3 V to 26 V, supports supply voltages up to 32 V, and has a listed input offset voltage of 3 mV. Its four-amplifier configuration allows one package to implement four independent analog signal-conditioning channels. An operational amplifier is a high-gain analog amplifier intended for closed-loop signal conditioning. The LM324 belongs to the broader operational amplifier, analog amplifier, and integrated-circuit hierarchy. Its differential inputs compare two voltages and drive an output according to the feedback network. True differential inputs are particularly useful in single-supply circuits, where an input signal can be referenced near ground without requiring a split bipolar power supply. The principal characteristics include four amplifiers per package, a 3 V to 26 V operating range, 3 mV input offset voltage, and approximately 0.6 V/us slew rate. The 14-TSSOP package provides a compact surface-mount format for general-purpose analog designs. The manufacturer identifies the LM324 series as a low-cost family with true differential inputs and several advantages over standard operational-amplifier types in single-supply applications. Each amplifier can be configured for voltage amplification, buffering, summing, filtering, or differential signal conditioning when suitable external resistors and capacitors are used. Because the LM324 contains four independent channels, designers can reduce component count in multi-channel instrumentation, sensor-conditioning, and feedback-control circuits. Independent channels also provide flexibility when different stages require different gain values or operating conditions. Typical uses include low-cost sensor interfaces, analog measurement chains, audio and communication equipment, power-supply feedback, and industrial control modules. In each case, the designer must verify input common-mode range, output swing, gain-bandwidth behavior, input bias current, and stability for the selected feedback network before releasing a production design. The main design consideration is the input common-mode range. A signal-sensing circuit should keep both inputs inside the amplifier's permitted common-mode window throughout its operating range. Decoupling capacitors should be placed close to the supply pins, while resistor and capacitor values should be calculated for the intended gain and bandwidth rather than copied without verification. This page consolidates electrical characteristics, package details, application guidance, practical design considerations, and qualified drop-in comparison information for engineers evaluating the LM324ADTBR2.

RFQ Kontak
LM324ADTBR2G - 3-32V Quad Op Amp | onsemi | TSSOP-14
LM324ADTBR2G

LM324ADTBR2G - 3-32V Quad Op Amp | onsemi | TSSOP-14

The onsemi LM324ADTBR2G is a general-purpose, single-supply quad operational amplifier with true differential inputs, a 3 V to 32 V supply range, 0.6 V/us slew rate, and 3 mV input-offset voltage. The four amplifiers are integrated in a 14-pin TSSOP package, providing a compact solution for low-cost signal conditioning, voltage amplification, filtering, and sensor-interface circuits. An operational amplifier, commonly called an op amp, is an analog semiconductor that uses high-gain differential amplification to improve the voltage level applied to its input signal. The LM324 belongs to the general-purpose amplifier class within the broader operational-amplifier, analog IC, and semiconductor hierarchy. Its four independent channels can process separate signals or be connected together for filtering, gain, summing, and other analog functions. The principal advantages of the LM324 family in single-supply systems include true differential inputs, operation from a supply as low as 3 V, and support for inputs that can approach ground potential. The integrated quad arrangement reduces component count and board area when a design needs several amplifiers. These characteristics make the device practical for cost-sensitive industrial control, instrumentation, audio, communications, and embedded-system analog front ends. Each channel consists of a differential input stage, intermediate gain stages, a push-pull output stage, and internal biasing. The output stage can source and sink current while driving typical external loads, and the device is intended for general-purpose closed-loop operation. Because it is not a rail-to-rail precision amplifier, input and output limitations must be considered when signals approach either supply rail. Typical applications include low-level sensor amplification, transducer conditioning, active filters, comparators with hysteresis, audio preamplification, current-to-voltage conversion, and general instrumentation. In a four-channel design, the same package can implement independent amplifier blocks or a higher-order filter. Supply bypassing remains essential because four amplifiers operating in one package can share the same rail and package-level thermal environment. For a new design, confirm input common-mode range, output swing, output-current capability, noise, offset, and stability requirements against the manufacturer datasheet before assigning gain. A 0.1 uF bypass capacitor close to the supply pins is a common starting point, while the datasheet should determine the final capacitance and compensation network for each feedback configuration. This product page combines the exact LM324ADTBR2G order information with verified manufacturer and distributor references, same-footprint alternatives, technical comparisons, and practical analog-design guidance. The comparisons also distinguish exact drop-in options from broader functional equivalents so engineers can protect PCB compatibility while reviewing speed, offset, supply, and temperature requirements.

RFQ Kontak
LM324AM - 4-Channel 3-32V Low-Power Op Amp | Texas Instruments
LM324AM

LM324AM - 4-Channel 3-32V Low-Power Op Amp | Texas Instruments

The Texas Instruments LM324AM is a four-channel, general-purpose operational amplifier operating from a single supply of 3 V to 32 V in a 14-pin SOIC package. Each amplifier provides approximately 65 dB CMRR, operates with an output current up to 40 mA, and is intended for low-power signal-conditioning applications. The LM324AM combines four independently usable amplifier sections in one surface-mount package, reducing board area compared with four separate single or dual amplifier packages. An operational amplifier is an analog signal-processing IC that amplifies the voltage difference between its inverting and non-inverting inputs. The LM324 belongs to the general-purpose operational-amplifier hierarchy: operational amplifier → voltage-feedback amplifier → integrated amplifier IC. Its four internal sections support common tasks including voltage buffering, transducer amplification, cross-coupled differential stages, analog filtering, and sensor-signal conditioning while operating from a single positive supply. The principal advantages of the LM324AM are its low-power four-channel integration, 3 V to 32 V single-supply range, approximately 65 dB CMRR, and low-power characterization emphasized by distributors. The 14-pin SOIC format supports conventional surface-mount assembly, while the four amplifier channels can provide independent gain or buffering functions within one package. The listed operating-temperature range is 0 °C to 70 °C, matching a general-purpose commercial-temperature class rather than an explicitly automotive-qualified product. The internally frequency-compensated architecture makes the LM324AM suitable for straightforward closed-loop amplifier configurations without external compensation networks. Designers should still verify input common-mode range, output swing, output-current capability, noise, slew rate, offset voltage, and channel behavior against the manufacturer datasheet for the exact production source and grade. Because LM324-family devices are also offered by multiple manufacturers, procurement should confirm the manufacturer marking, temperature grade, qualification status, and traceability. Typical uses include industrial 4-20 mA current-loop receivers, low-voltage sensor amplifiers, audio preamplifier stages, active filters, and general analog control boards. The integrated quad format is particularly useful when four similar amplifier channels are required. For a single- or dual-channel design, however, a one- or dual-amplifier package can reduce unused channels, power consumption, and PCB area. The principal design consideration is ensuring that the input and output operating points remain within the device's allowable common-mode and output-swing limits. Layout should keep feedback-loop connections short, provide local bypassing at the supply pins, and avoid placing high-current return paths beneath sensitive analog inputs. Stable operation near ground-level signals should be checked carefully when the source impedance is high or when the required output amplitude approaches the supply rails. This page consolidates verified distributor and manufacturer information, package-level replacement guidance, practical layout notes, and parameter-by-parameter comparisons. It also distinguishes verified facts from specifications that require confirmation from the exact manufacturer datasheet, helping engineers select and qualify the LM324AM without relying on generic family assumptions.

RFQ Kontak
LM324AM/NOPB - 4-Channel 1 MHz Op Amp | Texas Instruments
LM324AM/NOPB

LM324AM/NOPB - 4-Channel 1 MHz Op Amp | Texas Instruments

The Texas Instruments LM324AM/NOPB is a four-channel, general-purpose operational amplifier with a 1 MHz gain-bandwidth product, 0.5 V/us slew rate, and 3 V to 32 V single-supply operation in a 14-pin SOIC package. The LM324AM/NOPB contains four independent, high-gain, internally frequency-compensated amplifiers, allowing one device to implement multiple analog signal-conditioning channels while reducing package count and board area. An operational amplifier is an analog amplifier used to amplify voltage differences and serve as a building block in analog and mixed-signal systems. The LM324 family belongs to the operational-amplifier, analog-amplifier, and semiconductor hierarchies. Its four channels can perform buffering, voltage amplification, summing, comparison, filtering, and transducer-signal conditioning when configured with passive networks or companion components. The principal operating characteristics include four amplifier circuits, a 1 MHz gain-bandwidth product, 0.5 V/us slew rate, and a 3 V to 32 V total supply range. The low-power bipolar architecture supports single-supply operation, while internal frequency compensation allows practical closed-loop gain stages without external compensation components. The 14-pin SOIC form factor is also compatible with standard surface-mount assembly and tube-packaging workflows. Internal frequency compensation trades higher bandwidth for simple implementation and stable operation in general-purpose analog circuits. Each amplifier can use its supply rails as input common-mode limits, so input and output signals must remain within the permitted operating range. Circuit designers should account for input offset voltage, input bias current, output-current capability, common-mode limits, and output swing when choosing gain, feedback values, and external loading. Typical uses include four-channel sensor conditioning, low-frequency active filters, audio preamplifier stages, general signal buffers, DC summing networks, and mixed-signal interface circuits. The 1 MHz bandwidth is most appropriate for low-frequency and moderate-bandwidth tasks rather than high-speed instrumentation, where a wider-bandwidth amplifier would normally be preferred. The four-channel configuration is especially useful when a board needs several matched general-purpose amplifier functions. Keep input and output return paths short, decouple each supply rail close to the device, and place feedback components close to the relevant amplifier pins. Avoid driving capacitive loads directly unless the configured gain, load value, and stability behavior have been checked. Input bias-current compensation is important for high-impedance sources because the LM324 uses bipolar input transistors rather than CMOS inputs. This product record combines the exact LM324AM/NOPB package, operating, and amplifier data with practical application guidance, drop-in comparison options, and design considerations for efficient single-supply analog design.

RFQ Kontak
LM324AMX/NOPB - 32V Quad 1MHz Op Amp | Texas Instruments
LM324AMX/NOPB

LM324AMX/NOPB - 32V Quad 1MHz Op Amp | Texas Instruments

The Texas Instruments LM324AMX/NOPB is a low-power, general-purpose quad operational amplifier containing four independent, high-gain, internally frequency-compensated amplifiers. The device operates from a single power supply across a 3 V to 32 V range and provides approximately 1 MHz gain-bandwidth performance. It is packaged in a 14-pin SOIC (D) rated for a 0°C to 70°C ambient temperature range. An operational amplifier is an analog signal-conditioning IC that amplifies the difference between its inverting and non-inverting inputs. The operational-amplifier category includes general-purpose amplifiers, precision amplifiers, instrumentation amplifiers, and comparators; the LM324 belongs to the general-purpose single-supply amplifier family. Its four independent channels can run from the same supply while handling separate signal paths. The LM324AMX/NOPB provides a large DC voltage gain of 100 dB and is internally compensated for stable operation at unity gain. Its wide 3 V to 32 V supply range supports both conventional 5 V and 12 V analog systems as well as higher-voltage industrial rails. The output can swing from approximately 0 V to VCC minus 1.5 V, making rail-to-rail operation unnecessary when the signal remains within that range. The input common-mode voltage range includes ground, which is useful for single-supply sensing circuits. The amplifier's low-power architecture suits battery-operated instrumentation, analog signal conditioning, sensor amplification, and control loops where a precision rail-to-rail amplifier is unnecessary. Four amplifiers in one package also reduce board area when a design needs several similar analog channels. The internally compensated topology simplifies stable feedback design around unity gain, although applications requiring higher closed-loop gain or faster settling need additional bandwidth and stability analysis. Typical uses include transducers with ground-referenced outputs, current sensing, buffering, level shifting within the common-mode range, and general-purpose analog filtering. Each channel provides input and output pins in the same 14-pin SOIC outline, so no external isolation or separate bias circuitry is required for the basic amplifier function. Design should preserve the input common-mode and output-swing limits, especially near the positive supply rail. Where the signal can approach the upper rail, add headroom or select an amplifier with rail-to-rail output capability. Decoupling capacitors should be placed close to the supply pins, and unused amplifier channels should be configured conservatively rather than left floating. This page combines manufacturer specifications with package details, application guidance, drop-in replacement analysis, and practical design notes to support faster component selection and PCB planning.

RFQ Kontak
LM324AN - Quad 30V 1.2MHz Op Amp | Texas Instruments
LM324AN

LM324AN - Quad 30V 1.2MHz Op Amp | Texas Instruments

The Texas Instruments LM324AN is a low-power, quad operational amplifier containing four independent, high-gain, internally frequency-compensated amplifiers in a 14-pin PDIP package. The device operates from a single power supply, supports a maximum supply voltage of 30 V, and is specified for a gain-bandwidth product of 1.2 MHz with an input offset voltage rating of 3 mV. Its operating temperature range is 0°C to 70°C. An operational amplifier is an analog integrated circuit that amplifies the difference between its non-inverting and inverting inputs. The LM324AN belongs to the general-purpose operational amplifier family within the broader voltage-amplifier and analog signal-conditioning hierarchy. Internally compensated gain stages allow the amplifier to provide stable closed-loop operation without an external compensation capacitor, while the differential input architecture supports common-mode operation from ground upward in many single-supply circuits. Each of the four amplifier sections has a differential input, an output, and internal bias compensation. The 3 mV input offset rating is suitable for general instrumentation, sensor interfaces, active filtering, and audio preamplification where the signal is not operating near the precision limits of a dedicated low-offset amplifier. The 1.2 MHz gain-bandwidth product provides adequate bandwidth for low-frequency control, buffering, and modest-frequency signal-processing applications. The LM324AN is a classic single-supply-oriented device, but its wide supply capability also permits conventional dual-supply operation where the common-mode input range permits it. The four independent amplifiers can implement separate gain stages, comparators, filters, or buffer functions in one package. The through-hole PDIP construction is particularly useful for prototype boards, educational systems, industrial controllers, and repair assemblies where socketed or manually inserted parts are preferred over fine-pitch surface-mount packages. Typical uses include DC signal conditioning, bridge-amplifier interfaces, loop filtering, audio mixing stages, general feedback control, and low-cost sensor amplification. Because the LM324AN is not a rail-to-rail input or output amplifier, the engineer should verify input common-mode range and output swing against the selected supply voltage. Decoupling capacitors are normally placed close to the supply pins to control impedance and prevent feedback from disturbing analog signal integrity. For new precision designs, compare the LM324AN with rail-to-rail or low-offset alternatives before committing to the design. For established DIP-14 layouts and repair work, the LM324AN remains useful because several LM324-family devices from different manufacturers are offered in the same 14-pin through-hole footprint. Pricing shown for this page is referenced as of October 29, 2026 and should be rechecked against current distributor inventory. This page consolidates manufacturer specifications, verified distributor listings, cross-reference options, pin-level implementation guidance, and application-specific design notes that help engineers evaluate the LM324AN beyond a basic distributor catalogue entry.

RFQ Kontak
LM324AN/NOPB - Quad 1 MHz General-Purpose Op Amp | Texas Instruments
LM324AN/NOPB

LM324AN/NOPB - Quad 1 MHz General-Purpose Op Amp | Texas Instruments

The Texas Instruments LM324AN/NOPB is a quad general-purpose operational amplifier in a 14-pin PDIP package, integrating four independent, high-gain, internally frequency-compensated amplifiers in one monolithic die. Each channel operates from a single supply as low as 3 V up to 30 V, delivering a typical open-loop gain of 100 dB, a 1.0 MHz gain-bandwidth product and a 0.5 V/us slew rate. An operational amplifier (op amp) is a high-gain differential amplifier whose inverting and non-inverting inputs are compared and amplified. When negative feedback is applied, the closed-loop gain is set entirely by external resistors, which makes the op amp the basic building block of the analog signal chain: it sits in the hierarchy above discrete transistor gain stages and below complete application circuits such as amplifiers, filters, comparators, transducers and line drivers. The LM324 family, introduced by National Semiconductor and now a Texas Instruments product, is the archetypal single-supply general-purpose quad. The LM324A device in the LM324AN/NOPB provides a typical input offset voltage of 2 mV, an input bias current of 250 nA, and a typical supply current of 0.8 mA per amplifier, so four channels consume roughly 3.2 mA at 5 V. Output swing reaches within 20 mV of the negative rail and about 100 mV below the positive rail at 100 kΩ load, while the output can source or sink tens of milliamperes. Internal differential input and output protection diodes tolerate rail-to-rail input transients. The architecture is a classic bipolar, voltage-feedback design with a single dominant-pole compensation network per channel, giving unity-gain stability without external compensation. Noise is dominated by input-referred voltage noise of roughly 45 nV/√Hz at 1 kHz, and the amplifiers are designed for unity-gain operation in comparators, buffers and general analog signal conditioning. Typical applications include low-cost sensor signal conditioning, 4-20 mA current-loop receivers, audio mixer subcircuits, active filters, temperature controllers, bridge amplifier front ends, power-supply feedback loops and general instrumentation. Because the package is a through-hole PDIP-14, the part also fits legacy industrial and educational control boards that were designed around the original LM324 footprint. A key design consideration is that the LM324 does not rail-to-rail output and its common-mode input range excludes the positive rail, so headroom must be planned for single-supply designs. The input bias current flows through the source resistance, so matched resistor networks keep output offset small. Using the device as a comparator requires care because output saturation recovery takes several microseconds. This page adds information the datasheet does not provide: a drop-in alternative matrix with quantified differences, package and pinout reference, engineering design notes covering decoupling and input common-mode limits, and a parameter-by-parameter comparison table for selecting between the Texas Instruments, onsemi and equivalent quad op amp sources.

RFQ Kontak