AD745KR-16 - 20MHz Low-Noise J-FET Op Amp | Analog Devices
MPN: AD745KR-16 ✓ NakahandaAD745KR-16 Ulas
An operational amplifier is an analog signal-processing building block that amplifies the voltage difference between its inverting and non-inverting inputs. The AD745 belongs to the precision-amplifier hierarchy, where accurate amplification, low noise, and high bandwidth are more important than saturated-output or high-output-current performance. Its low-noise J-FET input stage makes the device suitable for instrumentation, sensor interfaces, and precision signal-conditioning circuits.
The AD745's headline characteristics include a 20 MHz gain-bandwidth product, a 12.5 V/µs slew rate, and ultralow voltage-noise performance. The 20 MHz bandwidth allows the amplifier to process signals well above the audio range, while the 12.5 V/µs slew rate supports accurate reproduction of large, fast transitions. Because it is a J-FET-input amplifier, the device also offers very low input bias currents, which helps minimize distortion when driven by high-impedance sources.
The AD745 can operate on dual supplies or as a single-supply amplifier when the input and output common-mode ranges permit. Design work should verify the supply voltage, input common-mode range, output swing, stability, and noise specifications against the operating conditions in the manufacturer datasheet. Decoupling capacitors should be placed close to the supply pins, and feedback resistors should be selected to preserve the intended closed-loop bandwidth.
Typical uses include precision current-to-voltage conversion, low-level sensor amplification, photodiode and phototransistor interfaces, audio and communication-signal conditioning, laboratory measurement front ends, and high-impedance buffer stages. The combination of 20 MHz bandwidth, 12.5 V/µs slew rate, and low-noise J-FET inputs is particularly useful when the source impedance is high enough that input bias current would otherwise create unacceptable offset errors.
A key design consideration is that the AD745 is optimized for low-noise, high-speed signal work rather than rail-to-rail input and output operation. Check headroom at both ends of the signal range and account for bias-current-generated error across the source impedance. Feedback-component values and source impedances should also be checked against the amplifier's stability requirements.
This page organizes the AD745KR-16 electrical characteristics, package details, application guidance, same-footprint amplifier alternatives, and design notes in one place. It also identifies which published parameters need confirmation in the manufacturer datasheet, helping engineers move from part selection to a validated analog design.
Mga alternatibo na pwedeng ilagay na AD745KR-16 — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok AD745KR-16 (parehas na form factor at footprint) — pagkakaiba sa Amplifier Type, Mounting Type, Package, Slew Rate.
AD745JRZ-16
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
AD745KRZ-16-REEL7
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
AD745ARZ-16
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
AD745BRZ-16
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
AD745CRZ-16
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
AD745KR-16 Mga Pinakamataas na Rating at Electrical Characteristics
| Amplifier Type | Single precision operational amplifier |
| Topolohiya | J-FET input |
| Number of Circuits | 1 circuit |
| Gain-Bandwidth Product | 20 MHz |
| Slew Rate | 12.5 V/µs |
| Packhaging | 16-lead SOIC |
| Uri ng Pagpapasok | Surface mount |
Gabay sa Pin Configuration ng AD745KR-16 16-lead soic
Pin configuration para sa AD745KR-16 (16-lead soic package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.
Wala ng detalyadong pinout data na magagamit para sa AD745KR-16.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
AD745KR-16 ay nararapat para sa 6 aplikasyons: Photodiode Signal Conditioning, Precision Sensor Amplification, Current-to-Voltage Conversion, Audio and Communications Conditioning, Laboratory Instrumentation Front End, Precision Buffering.
Photodiode Signal Conditioning
The AD745KR-16 fits low-level photodiode front ends because its J-FET input stage avoids the large bias-current errors that can arise with bipolar input amplifiers when the source impedance is high. The 20 MHz gain-bandwidth product supports signal-chain bandwidth beyond audio frequencies, while the 12.5 V/µs slew rate allows accurate recovery of fast phototransients. In a transimpedance design, the amplifier converts photocurrent into a proportional voltage, and reverse-bias leakage of the photodiode becomes an important error source. The low input current of the AD745 helps limit that leakage contribution. Keep the feedback resistor and compensation capacitor close to the amplifier, and verify the total input capacitance against the noise and stability requirements in the manufacturer datasheet.
Inirekomenda
Precision Sensor Amplification
High-impedance sensors benefit from the AD745KR-16 because its J-FET input stage combines low voltage noise with very low input bias current. This combination reduces the offset and gain errors introduced when the sensor current flows through a large source impedance. The amplifier's 20 MHz gain-bandwidth product permits closed-loop gains that retain useful bandwidth, and its 12.5 V/µs slew rate supports relatively rapid signal movement. The circuit is suitable for resistive sensors, strain-gauge bridges, and capacitive sensing front ends where the source impedance is high. Decoupling, guarding, and clean return paths should be treated as part of the measurement design, since guarding around high-impedance inputs can further reduce leakage pickup.
Inirekomenda
Current-to-Voltage Conversion
The AD745KR-16 is useful in transimpedance converters where a small input current must be converted into a measurable voltage. Its low-noise J-FET input reduces the current generated by the amplifier itself, preventing that contribution from being confused with the sensor current. The 20 MHz gain-bandwidth product allows the closed-loop transimpedance bandwidth to extend into the megahertz region when resistor and capacitor values are chosen correctly, while the 12.5 V/µs slew rate helps maintain fidelity on fast current edges. Check the amplifier's input-capacitance limits and the compensation strategy for the exact feedback network. PCB leakage, contaminated boards, and surface moisture can dominate the useful accuracy of this type of measurement.
Inirekomenda
Audio and Communications Conditioning
The AD745KR-16 provides enough bandwidth and slew rate for audio-frequency and communications-signal conditioning while retaining the low-noise behavior expected from a precision amplifier. A 20 MHz gain-bandwidth product allows useful closed-loop bandwidth in gain configurations below unity, and the 12.5 V/µs slew rate limits large-signal distortion on faster transitions. The J-FET input stage can be advantageous when the source impedance is high and bias-current distortion would otherwise be significant. In a practical circuit, the feedback network should preserve the intended noise and bandwidth balance rather than using unnecessarily low resistance values. Output drive, load capacitance, and stability must be checked against the selected gain because capacitive loading can alter the effective response.
Inirekomenda
Laboratory Instrumentation Front End
The AD745KR-16 can form the first amplification stage of a laboratory measurement system when the source is high impedance and the signal must be preserved with low added noise. Its 20 MHz gain-bandwidth product supports wide-band measurement channels, and the 12.5 V/µs slew rate provides margin for fast test signals. The single-amplifier configuration reduces board area while retaining a straightforward 16-lead SOIC footprint. Designers should confirm the output swing against the instrument's full-scale range and account for the amplifier's quiescent current in the overall power budget. Short, guarded input routes and solid grounding are particularly important at the microvolt level because induced pickup can otherwise resemble the signal being measured.
Inirekomenda
Precision Buffering
The AD745KR-16 can buffer a high-impedance source when the driven load requires more current or lower output impedance than the source can provide. Its low-bias-current J-FET input stage minimizes the loading error introduced at the source, while the 20 MHz gain-bandwidth product and 12.5 V/µs slew rate support signals beyond the audio range. Follower or non-inverting configurations are possible when the amplifier's common-mode and output ranges are compatible with the signal. The load impedance and any connected cable capacitance should be reviewed before layout is finalized, since long interconnects can add capacitance that changes the stability margin. Keep sensitive input nets short and place the bypass capacitor directly across the supply pins.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for AD745KR-16 — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | AD745JRZ-16 | AD745KRZ-16-REEL7 | AD745ARZ-16 | AD745BRZ-16 | AD745CRZ-16 |
|---|---|---|---|---|---|---|
| Package | 16-lead SOIC | 16-lead SOIC - same footprint | 16-lead SOIC - same footprint | 16-lead SOIC - same footprint | 16-lead SOIC - same footprint | 16-lead SOIC - same footprint |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Amplifier Type | Single precision J-FET operational amplifier | Single J-FET operational amplifier | Single J-FET operational amplifier | Single J-FET operational amplifier | Single J-FET operational amplifier | Single J-FET operational amplifier |
| Gain-Bandwidth Product | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| Slew Rate | 12.5 V/µs | 12.5 V/µs | 12.5 V/µs | 12.5 V/µs | 12.5 V/µs | 12.5 V/µs |
| Input Stage | J-FET | J-FET | J-FET | J-FET | J-FET | J-FET |
| Number of Circuits | 1 | 1 | 1 | 1 | 1 | 1 |
| Ordering Option Difference | AD745KR-16 | Different grade code | Reel packing notation | Different grade code | Different grade code | Different grade code |
Pangunahing mga Pagkakaiba
- Combines J-FET input behavior with substantial signal bandwidth (kumpara saAD745JRZ-16)
- Single-amplifier implementation reduces analog footprint (kumpara saAD745KRZ-16-REEL7)
- Supports low-impedance-error sensing and fast signal recovery (kumpara saAD745ARZ-16)
Talaan ng Disenyo
Place the supply bypass capacitor immediately across the positive and negative supply pins, with very short traces and a direct ground return. For high-impedance input circuits, minimize copper area around the input pins, remove flux residue, and consider guarding. These steps matter because an AD745's low-noise performance cannot be recovered if leakage, contamination, or switching pickup is already present at the input.
Account for source capacitance and the combined parasitic capacitance of the feedback network when working with the AD745's 20 MHz gain-bandwidth product. Long feedback traces or excessive load capacitance can change the effective settling behavior. Keep the feedback loop compact, connect the inverting input directly to the feedback network, and evaluate the final PCB with a scope before releasing the design for production.
Do not assume that every AD745 ordering code has identical temperature or qualification requirements. Confirm the grade code, supply range, common-mode range, and output swing in the manufacturer datasheet for the exact ordering option. When substituting a family member, verify the physical lead mapping and electrical limits rather than relying only on the shared 16-lead SOIC package name.
Use the lowest supply voltage that satisfies the signal, common-mode, and output-swing requirements while leaving suitable headroom for temperature and tolerance variation. The 12.5 V/µs slew rate can produce high dynamic demand during fast output transitions, so the supply network must remain low impedance at signal frequencies. Separate sensitive analog routing from switching-node and high-current return paths where the board layout permits.
Impormasyon ng Pagsunod sa Kautusan
Compliance and qualification statements were not explicitly identified for this ordering code. Confirm RoHS, REACH, halogen-free, conflict-minerals, and AEC-Q100 status on the manufacturer product page and in the latest manufacturer documentation.