ADV3222ARZ-R7 - 800 MHz 4:1 Analog Multiplexer | Analog Devices
MPN: ADV3222ARZ-R7 ✓ NakahandaADV3222ARZ-R7 Ulas
An analog multiplexer is a switching semiconductor that connects one signal path to one of several inputs. A 4:1 device therefore routes four channels through a common output or common terminal. Buffering the switched signal reduces impedance interaction between the source, selected channel, and receiving circuit. The ADV3222 belongs to the analog switch and multiplexer hierarchy, placing it above basic passive switches and alongside high-speed analog-routing ICs used in test systems, communications equipment, video electronics, and data-acquisition systems.
The ADV3222ARZ-R7 offers a minus-3 dB bandwidth of 800 MHz for a 200 mV peak-to-peak input and 750 MHz for a 2 V peak-to-peak input. Its 2400 V/us slew rate supports rapid transitions, while channel switching occurs in less than 20 ns with 1% settling. The bidirectional architecture allows the same package to support routing arrangements in which signal flow is not fixed in advance. Analog Devices also identifies low power consumption of 75 mW at plus or minus 5 V as a key feature.
The device provides strong isolation between channels and is suitable for video performance measurements extending to 100 MHz with 0.1 dB variation. These characteristics make it useful where a source must be selected rapidly without severe insertion loss or crosstalk between selected and unselected paths. Its high-speed buffered architecture is particularly valuable in automated test equipment, broadcast video routing, instrumentation, and communications signal paths.
Typical uses include high-speed video test systems, communications equipment, data-acquisition front ends, ATE, and semiconductor test systems. In each case, the multiplexer can reduce the number of separate signal paths while allowing a controller to select the required channel. The 16-SOIC package is also compatible with conventional surface-mount PCB assembly methods.
Designers should preserve the signal-path symmetry recommended by the manufacturer, place the device close to the driven and receiving circuits, and provide stable supply bypassing. Short, controlled routing is important because even a high-bandwidth multiplexer cannot recover insertion loss, reflections, or crosstalk introduced by poorly terminated PCB traces. Decoupling capacitors should connect directly to the supply and ground pins with minimal loop area.
This page consolidates the key bandwidth, switching, isolation, application, and replacement information engineers need when evaluating the ADV3222ARZ-R7 for a high-speed 4:1 routing design, while also identifying parameter checks that should be completed before selecting a substitute device.
Mga alternatibo na pwedeng ilagay na ADV3222ARZ-R7 — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok ADV3222ARZ-R7 (parehas na form factor at footprint) — pagkakaiba sa Power Consumption, Slew Rate, Crosstalk, Number of Circuits, Package.
ADV3221ARZ-R7
✅ Drop-In ⚠️ Mga Talaan Hindi NaiwerikmoMagkontak para sa presyo
Tingnan ang Datasheet →ADV3221ARZ
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo✓ Sa Stock
$7.5469 / Yunit
Tingnan ang Datasheet →ADV3222ARZ-R7 Mga Spesipikasyon
| Device Type | 4:1 analog multiplexer |
| Number of Circuits | 1 circuit |
| Channel Direction | Bidirectional |
| Minus-3 dB Bandwidth at 200 mV p-p | 800 MHz |
| Minus-3 dB Bandwidth at 2 V p-p | 750 MHz |
| Slew Rate | 2400 V/us |
| Channel Switching Time | Less than 20 ns to 1% settling |
| Crosstalk | Less than 58 dB |
| Video Performance | 100 MHz with 0.1 dB variation |
| Power Consumption | 75 mW at plus or minus 5 V |
| Hanay ng Temperature na Operasyon | -40 C to +85 C |
| Packhaging | 16-SOIC |
| Uri ng Pagpapasok | Surface Mount |
Gabay sa Pin Configuration ng ADV3222ARZ-R7 16-soic
Pin configuration para sa ADV3222ARZ-R7 (16-soic package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa ADV3222ARZ-R7.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
ADV3222ARZ-R7 ay nararapat para sa 6 aplikasyons: Automated Semiconductor Test Systems, Broadcast Video Source Routing, Communications Signal Routing, High-Speed Data Acquisition, Video Test Equipment, Wideband Test Fixture Routing.
Automated Semiconductor Test Systems
The ADV3222ARZ-R7 fits high-speed automated test equipment that must route instrument or device-under-test signals between several sources and measurement channels. Its 4:1 architecture reduces the number of physical signal paths, while the less-than-20 ns switching time supports rapid test sequencing. An 800 MHz bandwidth at 200 mV peak-to-peak and 2400 V/us slew rate preserve short rise times and wide frequency coverage. The 16-SOIC footprint also simplifies assembly around densely populated tester cards. Signal integrity remains a board-level concern, so use controlled-impedance routing, suitable source and load impedances, and short connections between the multiplexer and the instrument interface.
Inirekomenda
Broadcast Video Source Routing
The ADV3222ARZ-R7 is appropriate for professional video routing where one receiver must select among four synchronized sources. Analog Devices specifies video performance to 100 MHz with 0.1 dB variation, while the larger-signal bandwidth reaches 750 MHz at 2 V peak-to-peak. Fast settling below 20 ns helps minimize disruption during source changes, and bidirectional channels support flexible routing topologies. The principal design requirement is maintaining controlled impedance from source to mux and from mux to receiver. Use short PCB paths, a continuous reference plane, and termination appropriate to the video standard so reflections and skin effects do not reduce the usable performance of the selected channel.
Inirekomenda
Communications Signal Routing
The ADV3222ARZ-R7 can route high-frequency communications signals through a compact four-channel selection network. Its 800 MHz minus-3 dB bandwidth covers a broad range of IF and wideband test signals, while the 2400 V/us slew rate reduces distortion when passing fast transitions. Bidirectional operation allows the same device to support different board-level signal-flow arrangements and simplifies common test fixtures. For RF and broadband installations, keep the selected path short and use impedance-matched terminations. Supply bypassing and grounding should follow the manufacturer layout recommendation because parasitic inductance in a high-speed mux path can otherwise degrade insertion loss and channel-to-channel isolation.
Inirekomenda
High-Speed Data Acquisition
The ADV3222ARZ-R7 is suitable for data-acquisition front ends that must select among four conditioned or raw input channels before conversion. The buffered topology helps isolate the selected source from the receiving instrument, and the less-than-20 ns switching time supports rapid acquisition sequencing. Its 800 MHz bandwidth is especially useful for waveform integrity, pulse, or communications-related measurements where slow transitions would alter the captured result. Place the mux close to the acquisition input to minimize trace loss, and establish the correct source and load impedances before evaluating bandwidth. The device does not replace front-end gain, filtering, or anti-alias filtering; those functions should be placed according to the required signal range.
Inirekomenda
Video Test Equipment
The ADV3222ARZ-R7 fits production and laboratory video test equipment that needs to apply or monitor several signal sources. The 100 MHz, 0.1 dB video-performance specification and 750 MHz bandwidth at 2 V peak-to-peak provide adequate margin for common composite and component-video test paths. Its fast channel transition can reduce dead time during automated test sequences, while bidirectional channels support reusable signal paths around source and analyzer instruments. The design should include controlled impedance, minimal connector-to-IC routing, and proper reference-plane continuity. Decouple the supply locally and verify settling at the analyzer rather than assuming the IC alone determines measurement accuracy.
Inirekomenda
Wideband Test Fixture Routing
The ADV3222ARZ-R7 is useful in configurable wideband fixtures where four stimulus or measurement channels must reach a common test port. Its 4:1 organization simplifies routing logic, and the 800 MHz bandwidth, 2400 V/us slew rate, and sub-20 ns settling support fast, high-amplitude test waveforms. The 16-SOIC package provides a straightforward surface-mount implementation for fixture boards. Maintain short traces and a continuous ground reference to minimize crosstalk, and use attenuation or gain stages when the selected signal could exceed the device's permitted input range. Confirm the logic-control timing and settling behavior within the complete fixture rather than evaluating only the multiplexer transition in isolation.
Inirekomenda
Impormasyon ng Talumpati sa Engineering for ADV3222ARZ-R7 — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | ADV3221ARZ-R7 | ADV3221ARZ |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-SOIC | 16-SOIC - same | 16-SOIC - same |
| Device Type | 4:1 analog multiplexer | 4:1 analog multiplexer | 4:1 analog multiplexer |
| Minus-3 dB Bandwidth at 200 mV p-p | 800 MHz | 800 MHz | 800 MHz |
| Channel Switching Time | Less than 20 ns with 1% settling | Less than 20 ns with 1% settling | Less than 20 ns with 1% settling |
Pangunahing mga Pagkakaiba
- Provides a complete four-channel routing function in one buffered device (kumpara saADV3221ARZ-R7)
- Maintains wide signal-level bandwidth for video and pulse testing (kumpara saADV3221ARZ)
- Combines high bandwidth with rapid channel settling (kumpara saADV3221ARZ-R7)
Talaan ng Disenyo
Keep every mux connection short and route each channel over a continuous reference plane. Avoid stubs, unnecessary vias, and long loops around the device because PCB inductance and capacitance can degrade insertion loss and isolation even when the IC bandwidth is adequate. Use the same controlled-impedance geometry for all four channels so timing and amplitude behavior remain similar after selection.
Place the manufacturer-recommended bypass capacitors directly beside the power and ground pins. Each capacitor-to-pin connection should form the shortest possible loop, with a substantial ground-plane connection and no shared narrow neck between devices. This arrangement reduces supply impedance at high switching rates and helps prevent transient supply movement from disturbing the selected signal channel.
Terminate the source and load for the impedance and bandwidth of the selected path. Incorrect source impedance can alter the effective bandwidth and transition rate, while an inappropriate load can create reflections that appear as extra ringing or poor settling. Validate the complete path with the actual source impedance, load, cable or connector, PCB geometry, and measurement bandwidth.
Do not treat the less-than-20 ns switching specification as the total time required for a system waveform to settle. External capacitance, load impedance, connector delay, PCB propagation, and the measurement threshold all contribute to observed timing. Check the control sequence and allow adequate guard time before evaluating a newly selected channel in automated equipment.
Impormasyon ng Pagsunod sa Kautusan
Compliance attributes were not identified in the retrieved manufacturer, distributor, or catalog information. Verify the current declarations for the exact orderable MPN before treating the device as RoHS, REACH, lead-free, halogen-free, or AEC-Q100 qualified.