CD4053BCN - Triple 2:1 CMOS Multiplexer | onsemi
MPN: CD4053BCN ✓ NakahandaCD4053BCN Ulas
An analog multiplexer is an interface IC that connects one of multiple internal signal paths to a shared output. The CD4053BCN belongs to the CMOS logic family and uses digital select inputs to control analog signal routing. This places it within the hierarchy of multiplexer, analog switch, interface IC, and semiconductor. The stated on-resistance of 240 ohms is important when the switched signal is sourced from a relatively high-impedance sensor or measurement node.
The principal device features are three independent 2:1 circuits, a 240-ohm on-resistance, CMOS construction, and a 16-pin PDIP package. Grouping three circuits into one package can simplify boards that repeatedly route analog, control, or instrumentation signals. The DIP-16 mechanical format also supports through-hole assembly, prototyping, repair, and applications where a socketed component is preferred.
Internally, the CD4053BCN combines analog switching with CMOS control logic. Its common select architecture is useful when several related channels should change together, although the exact truth-table relationship should be verified in the manufacturer datasheet before assigning control states. Because it is an analog switch rather than a digital bus transceiver, the selected signal must remain within the device's permitted voltage and current limits.
Typical uses include analog sensor selection, test-point routing, signal multiplexing in instrumentation, controlled sharing of multiple signal sources, and embedded measurement systems. A three-channel arrangement can also support phase, channel, or polarity selection where the routed signals are compatible with the switch's electrical characteristics and switching requirements.
PCB design should reserve the full 16-pin PDIP footprint and route high-impedance or fast-changing signals away from adjacent digital select lines. Keep input and output traces short, provide a stable ground reference, and follow the manufacturer datasheet for unused inputs, supply decoupling, and maximum signal excursion. Confirm operating voltage and temperature limits before committing to the device in production equipment.
Mga alternatibo na pwedeng ilagay na CD4053BCN — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok CD4053BCN (parehas na form factor at footprint) — pagkakaiba sa RoHS Status.
CD4053BE
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →CD4053BEE4
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
MC74HC4053ANG
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
CD4053BCN Mga Spesipikasyon
| Multiplexer Type | 3-circuit, single-ended 2:1 analog switch |
| Number of Circuits | 3 circuits |
| Number of Channels | 2 channels per circuit |
| On-Resistance | 240 ohms |
| Logic Family | CMOS |
| Signal Type | Single-ended |
| Package Type | PDIP-16 |
| Package Description | 0.3-inch plastic DIP-16, MS-001 |
| Bilang ng Pin | 16 pins |
| Uri ng Pagpapasok | Through-hole |
| Tindminan RoHS | Compliant |
Gabay sa Pin Configuration ng CD4053BCN 0.3-inch plastic dip-16, ms-001
Pin configuration para sa CD4053BCN (0.3-inch plastic dip-16, ms-001 package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa CD4053BCN.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
CD4053BCN ay nararapat para sa 6 aplikasyons: Analog Sensor Signal Multiplexing, Test and Measurement Signal Routing, Control Signal Routing, Industrial Equipment Interface Switching, Data Acquisition Channel Selection, Data Logger and Monitoring Systems.
Analog Sensor Signal Multiplexing
The CD4053BCN is suitable for selecting among related sensor signals when a shared processing channel is required. Its three 2:1 circuits allow three pairs of signal routes to be controlled from one package, while the 240-ohm on-resistance provides a defined series resistance in the selected path. The device is most appropriate for sensor outputs whose levels remain within the manufacturer's operating limits and whose source impedance does not make switch resistance excessive. Use a low-noise buffer after the multiplexer when the sensor impedance is high or the measurement requires very low offset error.
Inirekomenda
Test and Measurement Signal Routing
The CD4053BCN can route three pairs of measurement signals to a common instrument or processing input, reducing the number of discrete switches required on a test board. Its stated 240-ohm on-resistance must be included in the signal-path attenuation budget, especially when driving a high-impedance measurement front end. The PDIP-16 through-hole package is convenient for prototype fixtures and socketed laboratory hardware. Confirm switching time, off-isolation, leakage, and allowable input excursion in the manufacturer datasheet before using it for precision measurements.
Inirekomenda
Control Signal Routing
The CD4053BCN can select between two related control signals in three independent channels when the routed outputs are compatible with its CMOS switch behavior. Grouping the routing functions in one PDIP-16 package reduces board area and simplifies control of repeated channels. This approach is useful in small control systems where a microcontroller or logic device must choose one of two command sources, polarity sets, or operating modes. The selected signals should remain within the allowed voltage range, and the truth table should be checked carefully when one control action changes more than one path.
Inirekomenda
Industrial Equipment Interface Switching
The three 2:1 circuits of the CD4053BCN can support signal isolation routing between a controller and multiple external interface lines in industrial equipment. Its 240-ohm on-resistance is modest for many logic-level or medium-impedance industrial signals, allowing one component to replace several single switch channels. Through-hole assembly also supports repairable control boards and panel-wired equipment. The design must still account for transients, ground offsets, noise coupling, and the device's permitted signal excursion, none of which should be inferred solely from the package description.
Inirekomenda
Data Acquisition Channel Selection
The CD4053BCN can select paired inputs from a multi-channel data-acquisition front end before conversion or processing. Three independently addressed 2:1 sections make it practical to bring several related nodes onto a shared path while limiting component count. The 240-ohm switch resistance should be checked against the front-end input impedance, and channel capacitance may influence settling after each selection. For high-resolution or high-speed conversion, compare switching time, leakage, and input capacitance against the acquisition settling budget before committing the device.
Inirekomenda
Data Logger and Monitoring Systems
The CD4053BCN can route monitored signals in compact data loggers where multiple thresholds, alarm sources, or sensor outputs must be presented to a common monitoring input. A single triple multiplexer simplifies board construction while keeping the through-hole PDIP-16 format convenient for prototype and repair-oriented systems. The on-resistance contributes to attenuation and source loading, so the downstream input should have sufficiently high impedance. Select the exact operating grade only after verifying supply voltage, temperature range, and interface-level requirements in the manufacturer datasheet.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for CD4053BCN — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | CD4053BE | CD4053BEE4 | MC74HC4053ANG |
|---|---|---|---|---|
| Brand | onsemi | Texas Instruments | Texas Instruments | onsemi |
| Package | PDIP-16 | PDIP-16 - same | PDIP-16 - same | PDIP-16 - same |
| Multiplexer Function | Triple 2:1, single-ended | Triple 2:1, single-ended | Triple 2:1, single-ended | Triple 2:1, single-ended |
| Number of Circuits | 3 circuits | 3 circuits | 3 circuits | 3 circuits |
| Channels per Circuit | 2 channels | 2 channels | 2 channels | 2 channels |
| Logic Family | CMOS | CMOS | CMOS | CMOS |
| Mounting Style | Through-hole PDIP-16 | Through-hole PDIP-16 | Through-hole PDIP-16 | Through-hole PDIP-16 |
Pangunahing mga Pagkakaiba
- Three related 2:1 routing circuits in one package (kumpara saMC74HC4053ANG)
- Direct onsemi sourcing lineage for the named CD4053BCN (kumpara saCD4053BE)
- Documented 240-ohm on-resistance (kumpara saCD4053BEE4)
- Single package replaces three separate 2:1 switches (kumpara saCD4053BE)
Talaan ng Disenyo
Assign the PCB footprint directly from the 16-pin PDIP outline and verify each connection against the exact manufacturer pin-description table. The device combines three 2:1 switching circuits, so treating it as a generic 4:1 mux can produce incorrect routing. Keep the common paths and paired channel traces short, maintain a continuous ground reference, and avoid routing sensitive inputs directly beside the digital select lines. A socket may simplify DIP-16 prototype replacement.
Include the 240-ohm on-resistance in the complete source impedance and attenuation calculation. It is usually acceptable for logic-level routing but can materially affect a high-impedance sensor or precision measurement node. Check leakage, off-isolation, channel capacitance, and switching time against the required settling window. Place any following buffer or amplifier close to the multiplexer when additional source impedance would otherwise degrade accuracy or bandwidth.
Do not approve a replacement from package appearance alone. CD4053BE, CD4053BEE4, and MC74HC4053ANG use the identified PDIP-16 format and share the 3-function, 2-channel organization, but supply voltage, signal levels, switching impedance, control truth table, and qualification can differ between series. Compare every numbered pin and the worst-case electrical limits before releasing a substitution. Confirm that unused inputs are handled as directed by the manufacturer.
For mixed analog and digital routing, keep the three selected analog paths away from select-control traces and other switching nodes. Use a low-impedance ground plane, minimize loop area, and place any required bypass capacitor close to the device's supply and ground pins using the manufacturer reference layout. Through-hole DIP construction can increase loop area, so account for lead inductance and prototype-board cleanliness when operating signals at higher frequencies.
Impormasyon ng Pagsunod sa Kautusan
RoHS compliance is stated in the product listing. Other environmental, qualification, and material-compliance attributes were not established from the cited manufacturer information.