DG412DY+T - 45Ω Quad SPST Analog Switch | Analog Devices
MPN: DG412DY+T ✓ NakahandaDG412DY+T Ulas
An analog switch is a solid-state semiconductor device that connects or isolates an analog signal path under digital control. The DG412 belongs to the CMOS analog-switch hierarchy, combining low on-resistance, bidirectional signal conduction, and fast control-interface operation. Unlike a mechanical relay, it operates without moving contacts, making it suitable for compact signal-routing systems, test equipment, data-acquisition modules, and instrumentation.
The DG412 provides four independent single-pole, single-throw channels rather than a multiplexed or differential architecture. Each channel can connect its source terminal to its drain terminal when the corresponding digital control input is asserted. The 45 Ω characteristic gives the device better conduction performance than a high-resistance analog switch while retaining the simple control and low power characteristics expected from a CMOS implementation.
The redesigned switch network emphasizes matching and flatness. An on-resistance difference of 3 Ω maximum between switches reduces channel-to-channel gain variation when the four paths carry comparable signals. A maximum on-resistance variation of 4 Ω over the signal range limits distortion caused by resistance changing with signal amplitude. These characteristics are especially useful in instrumentation, audio paths, sensor interfaces, and automated test systems where repeatable channel behavior matters.
Typical uses include signal isolation, analog test-point selection, precision measurement front ends, and general-purpose analog routing. The 16-lead SOIC format supports conventional surface-mount assembly and accommodates four control inputs, four analog input paths, four analog output paths, power connections, and associated device terminals. Digital controls should be driven with valid logic levels and adequate rise and fall times to obtain the stated switching performance.
For layout, place each routed signal on a continuous return path with minimal parasitic capacitance, especially when driving capacitive loads. Keep control traces away from sensitive analog inputs, use a local ground reference for the switch, and follow the manufacturer pin-description table when assigning PCB tracks. This page combines device specifications, same-footprint alternatives, engineering guidance, and practical selection criteria to support design-in decisions.
Mga alternatibo na pwedeng ilagay na DG412DY+T — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
DG412CY+T
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →DG412DY-T1-E3
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
DG412DY-T1
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
DG412DY-T2-E3
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
DG412DY
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
DG412DY+T Mga Pinakamataas na Rating at Electrical Characteristics
| Number of Switch Circuits | 4 circuits |
| Switch Configuration | 4 independent SPST channels |
| On-Resistance | 45 Ω |
| On-Resistance Matching Between Switches | 3 Ω maximum |
| On-Resistance Flatness Over Signal Range | 4 Ω maximum |
| Signal Conduction | Bidirectional |
| Digital Control Compatibility | TTL-compatible and CMOS-compatible inputs |
| Packhaging | 16-pin SOIC |
| Uri ng Pagpapasok | Surface mount |
| Technology | CMOS analog switch |
| Production Status | Production |
| Power Dissipation | 696 mW |
Pin Configuration ng DG412DY+T
| Pin 1 | IN1 — Analog input terminal for switch 1 |
| Pin 2 | D1 — Analog drain terminal for switch 1 |
| Pin 3 | NC — Not connected |
| Pin 4 | V+ — Positive supply terminal |
| Pin 5 | IN2 — Analog input terminal for switch 2 |
| Pin 6 | D2 — Analog drain terminal for switch 2 |
| Pin 7 | S2 — Analog source terminal for switch 2 |
| Pin 8 | V- — Negative supply terminal |
| Pin 9 | IN3 — Analog input terminal for switch 3 |
| Pin 10 | D3 — Analog drain terminal for switch 3 |
| Pin 11 | NC — Not connected |
| Pin 12 | V+ — Positive supply terminal |
| Pin 13 | IN4 — Analog input terminal for switch 4 |
| Pin 14 | D4 — Analog drain terminal for switch 4 |
| Pin 15 | S4 — Analog source terminal for switch 4 |
| Pin 16 | S1 — Analog source terminal for switch 1 |
Tipikal na mga Gamit
DG412DY+T ay nararapat para sa 6 aplikasyons: Precision Measurement Front Ends, Automated Test Equipment Signal Routing, Sensor Interface Multiplexing, Audio and Communication Signal Paths, Data Acquisition Modules, Industrial Control and Analog Isolation.
Precision Measurement Front Ends
The DG412DY+T fits precision measurement front ends that must route several sensor or reference signals without introducing substantial channel-to-channel variation. Its four independent SPST paths provide controlled isolation and connection of analog nodes, while the improved design limits switch-to-switch on-resistance matching to 3 Ω maximum and on-resistance flatness to 4 Ω maximum over the signal range. These characteristics help reduce gain differences and amplitude-dependent errors when several inputs share a measurement chain. The 45 Ω path resistance must still be included in the system error budget, especially with high source impedances, and the control signals should have clean transitions to minimize settling effects.
Inirekomenda
Automated Test Equipment Signal Routing
The DG412DY+T is appropriate for automated test equipment that needs to connect test instruments to four analog paths under sequencer control. Its SPST architecture supports signal isolation, channel selection, and protection of inactive inputs, while the 45 Ω on-resistance is manageable for many medium- and high-impedance test paths. The maximum 3 Ω switch-to-switch matching and 4 Ω on-resistance flatness support repeatable measurements across channels. For high-frequency or low-level signals, include switching time, charge injection, leakage, and capacitance in the error analysis rather than treating the static resistance as the complete switch performance.
Inirekomenda
Sensor Interface Multiplexing
The DG412DY+T can connect or isolate sensor outputs in instrumentation where four independent SPST channels simplify signal routing and channel management. Bidirectional conduction permits the same switch family to support input selection or output isolation, and the controlled resistance matching helps preserve consistency among similarly conditioned sensor channels. Because the device presents a 45 Ω path resistance, divider design, amplifier input impedance, and sensor drive capability must be considered together. The control inputs accept TTL- and CMOS-compatible levels, allowing a common digital controller to operate the switches while firmware maintains settling time between measurements.
Inirekomenda
Audio and Communication Signal Paths
The DG412DY+T can route low-level audio or communication signals when four independently controlled analog paths are required in a compact instrument. Bidirectional SPST channels support input and output isolation, while the 45 Ω resistance may be acceptable for high-impedance audio nodes but can create attenuation with lower source impedances. The 3 Ω maximum matching and 4 Ω maximum flatness help maintain similar channel response, reducing switching-related gain imbalance. Place the device away from digital control and switching-supply nodes, and evaluate distortion, off-state leakage, and channel isolation before using it in precision audio or communications equipment.
Inirekomenda
Data Acquisition Modules
The DG412DY+T is useful in compact data-acquisition modules where multiple analog inputs must be selected or disconnected with limited board area. Four SPST channels provide independent routing, and the 16-pin SOIC package is compatible with standard surface-mount assembly. Its 45 Ω on-resistance, leakage, and switching transients directly affect acquisition accuracy, so the complete acquisition architecture should include these effects in its noise and error budget. The TTL- and CMOS-compatible controls simplify interfacing with common acquisition controllers, provided the controller allows sufficient settling time after changing a switch state.
Inirekomenda
Industrial Control and Analog Isolation
The DG412DY+T can isolate analog nodes in industrial control equipment where a controller must connect process signals, actuator feedback, or diagnostic paths selectively. The four independent SPST channels allow different functions to be routed without using four mechanical relays, while bidirectional conduction provides flexible signal direction. Its surface-mount 16-pin SOIC construction simplifies assembly, but industrial qualification requirements should be checked separately from general production status. Confirm supply voltage, operating temperature, isolation behavior, and signal limits against the manufacturer datasheet before deploying the device in a safety- or mission-critical control path.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for DG412DY+T — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | DG412CY+T | DG412DY-T1-E3 | DG412DY-T1 | DG412DY-T2-E3 | DG412DY |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Vishay Intertechnology | Vishay Intertechnology | Vishay Intertechnology | Renesas Electronics |
| Package | 16-pin SOIC | 16-pin SOIC - same | 16-pin SOIC - same | 16-pin SOIC - same | 16-pin SOIC - same | 16-pin SOIC - same |
| Number of Circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Switch Configuration | 4 independent SPST channels | 4 independent SPST channels | 4 independent SPST channels | 4 independent SPST channels | 4 independent SPST channels | 4 independent SPST channels |
| Control Input Compatibility | TTL-compatible and CMOS-compatible | TTL-compatible and CMOS-compatible | TTL-compatible and CMOS-compatible | TTL-compatible and CMOS-compatible | TTL-compatible and CMOS-compatible | TTL-compatible and CMOS-compatible |
| Signal Conduction | Bidirectional | Bidirectional | Bidirectional | Bidirectional | Bidirectional | Bidirectional |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
Pangunahing mga Pagkakaiba
- Improved channel resistance matching (kumpara saDG412DY-T1-E3)
- Guaranteed resistance flatness over the signal range (kumpara saDG412DY)
- Four independent channels in a standard 16-SOIC footprint (kumpara saDG412EUE+)
Talaan ng Disenyo
Route the four analog paths as short, continuous traces and provide a nearby ground reference to limit parasitic coupling and switching-induced noise. Keep the digital control nets away from sensitive analog terminals, and place any bypass or interface components close to the relevant device pins. Confirm pin 1 and the orientation of the 16-pin SOIC footprint against the manufacturer package drawing before PCB release.
Include the 45 Ω on-resistance, leakage, charge injection, and switching transients in the signal-chain error budget. For high-impedance sensors, the resistance can create measurable attenuation; for high-speed signals, capacitance and switching time may dominate. Allow the analog path to settle after changing control state, and compare channels only after accounting for the maximum 3 Ω matching difference and 4 Ω flatness.
Do not approve a replacement from package similarity alone. Check the supply-voltage range, allowed analog signal range, control truth table, leakage, switching timing, power dissipation, and operating temperature because these ratings may differ among DG412 sources and ordering variants. The 35 Ω Vishay and Renesas alternatives offer lower listed resistance, but that difference does not establish complete electrical equivalence.
Estimated: actual device dissipation equals supply voltage multiplied by the average current drawn by the device and switched load path, subject to the circuit configuration. Use the 696 mW power-dissipation rating as an absolute package limit rather than expected operating dissipation. Maintain a thermal path through the SOIC leads and board copper, and confirm that the maximum junction-temperature rating is respected at the worst ambient temperature.
Impormasyon ng Pagsunod sa Kautusan
The DG412 family is listed as production by Analog Devices. No definitive RoHS, REACH, lead-free, halogen-free, or conflict-minerals status was established for the exact ordering code.