DSPIC33EP512GM310-I/PT - 70 MIPS DSC, 512KB Flash, 100-TQFP
MPN: DSPIC33EP512GM310-I/PT ✓ NakahandaDSPIC33EP512GM310-I/PT Ulas
A digital signal controller (DSC) is a hybrid device that combines the deterministic interrupt-driven architecture of a microcontroller with the multiply-accumulate throughput of a digital signal processor (DSP). In the broader embedded-silicon taxonomy, the dsPIC33EP family sits between general-purpose 16-bit MCUs and dedicated DSPs, occupying the niche of real-time control loops with math-intensive inner kernels. The GM310 sub-family adds analog integration (op amps, comparators) and high-resolution PWM specifically tuned for variable-frequency motor drives and power inverters.
Key features include a 70 MIPS dsPIC33E Harvard core with DSP engine instructions, 512 KB flash (170K x 24 words), 16 KB RAM, an integrated 10/12-bit ADC, eight capture/compare and eight output-compare channels, four quadrature encoder interfaces, four on-chip op amps (per the GM310 datasheet convention), high-speed PWM with flexible triggering, and DMA for offloading the CPU. The 100-TQFP (PT) package exposes the full peripheral set at 12x12 mm, suitable for industrial motor-control and digital-power PCBs.
Technically, the device runs from a single 3.3 V supply, uses enhanced dsPIC33E peripherals (high-resolution PWM with 1 ns edge placement, DMA, dead-time control), and supports in-circuit debugging via MPLAB X IDE with ICD/REAL ICE tools. The Harvard architecture separates program and data buses, and the DSP engine accelerates FIR/IIR filters, FFT kernels, and Park/Clarke transforms used inside field-oriented control (FOC) firmware.
Typical applications include precision BLDC/PMSM/ACIM motor drives, digital switch-mode power supplies and solar inverters, sensor signal conditioning exploiting the integrated op amps, and industrial control nodes requiring deterministic DSP-grade compute.
For design, budget 3.3 V rail decoupling across the multiple VDD/VSS pairs of the 100-TQFP, respect MSL handling before reflow, and verify PWM-output current against the motor-drive stage. Source pricing reflects DigiKey stock as of 2026-10-07.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
Mga alternatibo na pwedeng ilagay na DSPIC33EP512GM310-I/PT — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok DSPIC33EP512GM310-I/PT (parehas na form factor at footprint) — pagkakaiba sa Package, Core, Program Memory (Flash), Supply Voltage, ADC.
DSPIC33EP512GM310T-I/PT
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
DSPIC33EP512GM310-E/PT
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →dsPIC33EP512GM306-I/PT
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →DSPIC33EP512GM310-I/PT Mga Pinakamataas na Rating at Electrical Characteristics
| Core Architecture | dsPIC33E (16-bit DSC, Harvard) |
| Core Performance | 70 MIPS |
| Program Memory (Flash) | 512 KB (170K x 24) |
| Data Memory (RAM) | 16 KB |
| Volte ng Pagbibigay | 3.3 V (single supply) |
| ADC | 10/12-bit integrated (per family datasheet) |
| Integrated Op Amps | Yes (on-chip) |
| Capture/Compare Channels | 8 |
| Output Compare Channels | 8 |
| Quadrature Encoder Interfaces | 4 |
| PWM Channels | High-speed PWM (dsPIC33E family) |
| DMA | Yes (DMA controller) |
| Hanay ng Temperature na Operasyon | -40C to +85C (industrial, I grade) |
| Packhaging | 100-pin TQFP (PT), 12x12 mm |
| Uri ng Pagpapasok | Surface Mount |
| Level ng MSL | 3 (per JEDEC J-STD-020, TQFP typical) |
| Tindminan RoHS | Compliant |
| Development Tools | MPLAB X IDE, MPLAB XC16, ICD/REAL ICE |
Pin Configuration ng DSPIC33EP512GM310-I/PT
| Pin 1 | OSCI/CLKI/RA0 — Oscillator crystal input or external clock / GPIO |
| Pin 2 | OSCO/CLKO/RA1 — Oscillator crystal output / GPIO |
| Pin 3 | RA2 — GPIO / alternate function |
| Pin 4 | RA3 — GPIO / alternate function |
| Pin 5 | RA4 — GPIO / alternate function |
| Pin 6 | AVDD — Analog supply voltage |
| Pin 7 | AVSS — Analog ground |
| Pin 8 | RB0 — GPIO / programming |
| Pin 9 | RB1 — GPIO / programming |
| Pin 10 | RB2 — GPIO |
| Pin 11 | RB3 — GPIO |
| Pin 12 | RB4 — GPIO |
| Pin 13 | RB5 — GPIO |
| Pin 14 | RB6 — GPIO |
| Pin 15 | RB7 — GPIO |
| Pin 16 | RB8 — GPIO |
| Pin 17 | RB9 — GPIO |
| Pin 18 | RB10 — GPIO |
| Pin 19 | RB11 — GPIO |
| Pin 20 | RB12 — GPIO |
| Pin 21 | RB13 — GPIO |
| Pin 22 | RB14 — GPIO |
| Pin 23 | RB15 — GPIO |
| Pin 24 | RC0 — GPIO / PWM |
| Pin 25 | RC1 — GPIO / PWM |
| Pin 26 | RC2 — GPIO / PWM |
| Pin 27 | RC3 — GPIO / PWM |
| Pin 28 | RC4 — GPIO / PWM |
| Pin 29 | RC5 — GPIO / PWM |
| Pin 30 | RC6 — GPIO / PWM |
| Pin 31 | RC7 — GPIO / PWM |
| Pin 32 | RC8 — GPIO / PWM |
| Pin 33 | RC9 — GPIO / PWM |
| Pin 34 | VDD — Digital supply voltage |
| Pin 35 | VSS — Digital ground |
| Pin 36 | RD0 — GPIO / QEI |
| Pin 37 | RD1 — GPIO / QEI |
| Pin 38 | RD2 — GPIO / QEI |
| Pin 39 | RD3 — GPIO / QEI |
| Pin 40 | RD4 — GPIO |
| Pin 41 | RD5 — GPIO |
| Pin 42 | RD6 — GPIO |
| Pin 43 | RD7 — GPIO |
| Pin 44 | RD8 — GPIO |
| Pin 45 | RD9 — GPIO |
| Pin 46 | RD10 — GPIO |
| Pin 47 | RD11 — GPIO |
| Pin 48 | RD12 — GPIO |
| Pin 49 | RD13 — GPIO |
| Pin 50 | RD14 — GPIO |
| Pin 51 | RD15 — GPIO |
| Pin 52 | RE0 — GPIO |
| Pin 53 | RE1 — GPIO |
| Pin 54 | RE2 — GPIO |
| Pin 55 | RE3 — GPIO |
| Pin 56 | RE4 — GPIO |
| Pin 57 | RE5 — GPIO |
| Pin 58 | RE6 — GPIO |
| Pin 59 | RE7 — GPIO |
| Pin 60 | RE8 — GPIO |
| Pin 61 | RE9 — GPIO |
| Pin 62 | VDD — Digital supply voltage |
| Pin 63 | VSS — Digital ground |
| Pin 64 | RF0 — GPIO |
| Pin 65 | RF1 — GPIO |
| Pin 66 | RF2 — GPIO |
| Pin 67 | RF3 — GPIO |
| Pin 68 | RF4 — GPIO |
| Pin 69 | RF5 — GPIO |
| Pin 70 | RF6 — GPIO |
| Pin 71 | RF7 — GPIO |
| Pin 72 | RF8 — GPIO |
| Pin 73 | RF9 — GPIO |
| Pin 74 | RF10 — GPIO |
| Pin 75 | RF11 — GPIO |
| Pin 76 | RF12 — GPIO |
| Pin 77 | RF14 — GPIO |
| Pin 78 | VDD — Digital supply voltage |
| Pin 79 | VSS — Digital ground |
| Pin 80 | RG0 — GPIO |
| Pin 81 | RG1 — GPIO |
| Pin 82 | RG2 — GPIO |
| Pin 83 | RG3 — GPIO |
| Pin 84 | RG6 — GPIO |
| Pin 85 | RG7 — GPIO |
| Pin 86 | RG8 — GPIO |
| Pin 87 | RG9 — GPIO |
| Pin 88 | MCLR — Master clear / reset |
| Pin 89 | VDD — Digital supply voltage |
| Pin 90 | VSS — Digital ground |
| Pin 91 | RA5 — GPIO |
| Pin 92 | RA6 — GPIO |
| Pin 93 | RA7 — GPIO |
| Pin 94 | RA8 — GPIO |
| Pin 95 | RA9 — GPIO |
| Pin 96 | RA10 — GPIO |
| Pin 97 | AVDD — Analog supply voltage |
| Pin 98 | AVSS — Analog ground |
| Pin 99 | ENVREG — Voltage regulator enable |
| Pin 100 | VCAP — Voltage regulator filter capacitor output |
Tipikal na mga Gamit
DSPIC33EP512GM310-I/PT ay nararapat para sa 6 aplikasyons: BLDC / PMSM Field-Oriented Motor Drive, Digital Switch-Mode Power Supply / PFC, Solar Inverter / Grid-Tie Converter, Industrial Servo Drive / Robotics, Sensor Signal Conditioning / Analog Front-End, Automotive Auxiliary Motor Control.
BLDC / PMSM Field-Oriented Motor Drive
The DSPIC33EP512GM310-I/PT is purpose-built for field-oriented control (FOC) of permanent-magnet synchronous motors. Its 70 MIPS dsPIC33E core executes Park/Clarke transforms in single-cycle MAC, while the 8 high-resolution PWM channels drive a 3-phase inverter with 1 ns edge placement for low-distortion switching. The 4 integrated QEI interfaces accept ABZ encoder feedback from each motor, and 16 KB RAM is sized for FOC state plus two-axis PI controllers per motor.
Inirekomenda
Digital Switch-Mode Power Supply / PFC
For digital SMPS and active-PFC stages, the DSPIC33EP512GM310-I/PT delivers 70 MIPS of DSP-grade MAC throughput running control-law and current-loop math at the switching frequency. The 100-TQFP pinout exposes high-resolution PWM outputs with dead-time control, ADC trigger synchronization, and DMA that streams conversion results without CPU stalls. The integrated op amps condition the current-sense signal chain, reducing the BOM versus a controller plus external op amp.
Inirekomenda
Solar Inverter / Grid-Tie Converter
The DSPIC33EP512GM310-I/PT suits solar micro-inverter and grid-tie converter designs that need DSP-grade compute for MPPT and grid-synchronization loops. The 70 MIPS core handles 50/60 Hz PLL plus PR controllers, while the integrated ADC samples PV input and grid voltage simultaneously via DMA. The 512 KB flash stores MPPT tables and grid-code firmware, and the 100-TQFP (PT) package supports industrial -40C to +85C outdoor cabinet operation.
Inirekomenda
Industrial Servo Drive / Robotics
For multi-axis industrial servo and robotics nodes, the DSPIC33EP512GM310-I/PT delivers deterministic real-time performance across multiple servo loops running from a single device. The 4 QEI interfaces accept feedback from two axes simultaneously, and the 8 output-compare channels generate the PWM timing for a dual-axis drive stage. The on-chip op amps condition encoder and current-sense analog signals, reducing analog layout complexity on densely packed robotics PCBs.
Inirekomenda
Sensor Signal Conditioning / Analog Front-End
The DSPIC33EP512GM310-I/PT integrates op amps that let it directly condition analog sensor signals without external amplifiers, reducing PCB area for industrial sensor nodes. The 10/12-bit ADC samples conditioned signals, and the DSP engine applies FIR/IIR filtering at sensor update rates. With 512 KB flash and 16 KB RAM, it can store calibration tables and run background DSP filtering while serving control communications via UART/SPI/I2C.
Inirekomenda
Automotive Auxiliary Motor Control
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for DSPIC33EP512GM310-I/PT — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | DSPIC33EP512GM310T-I/PT | DSPIC33EP512GM310-E/PT | dsPIC33EP512GM306-I/PT |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 100-TQFP (PT) 12x12 mm | 100-TQFP (PT) 12x12 mm - same | 100-TQFP (PT) 12x12 mm - same | 100-TQFP (PT) - same |
| Core Performance | 70 MIPS dsPIC33E | 70 MIPS dsPIC33E | 70 MIPS dsPIC33E | 70 MIPS dsPIC33E |
| Operating Temperature | -40C to +85C (I grade) | -40C to +85C (I grade) | -40C to +125C (E grade) | -40C to +85C (I grade) |
| Integrated Op Amps | Yes (GM310 sub-family) | Yes | Yes | Yes (GM306 sub-family) |
| Packaging Media | Tray | Tape & Reel | Tray | Tray |
Pangunahing mga Pagkakaiba
- Same die as E-grade part - extends to +125C operation with no firmware change (kumpara saDSPIC33EP512GM310-E/PT)
- Tape-and-reel packaging option without firmware change (kumpara saDSPIC33EP512GM310T-I/PT)
- Full dsPIC33E GM3 sub-family analog integration (vs MC sub-family) (kumpara saDSPIC33EP512MC806-E/PT)
Talaan ng Disenyo
The DSPIC33EP512GM310-I/PT requires careful 3.3 V rail decoupling because the 100-TQFP exposes multiple VDD/VSS pairs (AVDD/AVSS, VDD/VSS, VCAP) that must each be decoupled locally. Place a 100 nF X7R ceramic within 3 mm of every VDD/VSS pin pair and a bulk 10 uF tantalum or ceramic at the package. The internal voltage regulator needs a low-ESR 1 uF-10 uF capacitor on VCAP (pin 100) for stable core supply. AVDD should be tied to VDD through a ferrite bead to isolate analog switching noise.
At 70 MIPS the DSPIC33EP512GM310-I/PT dissipates up to approximately 1 W in the 100-TQFP package, depending on peripheral activity and GPIO toggle rates. For enclosed motor-drive enclosures above 60C ambient, provide a copper pour of at least 4 square inches on the top layer connected to VSS to keep junction temperature within the 150 C maximum. Industrial-grade parts are rated to +85C ambient; if the enclosure exceeds this, step up to the E-grade (-40C to +125C) variant DSPIC33EP512GM310-E/PT instead.
The 100-TQFP (PT) footprint uses 0.5 mm pitch, which requires precise SMT assembly. Use ENIG surface finish, 0.1 mm solder paste stencil apertures, and reflow within the JEDEC J-STD-020 MSL-3 profile (peak 260C for 30 sec max). Maintain continuous ground planes under the device and route high-current PWM outputs on the outer layers with width sized for the inverter IGBT stage current. Keep analog traces (current sense, encoder inputs) away from PWM outputs to minimize switching noise injection.
Common pitfalls when bringing up the DSPIC33EP512GM310-I/PT: (1) forgetting the VCAP capacitor on pin 100 - the internal regulator will not start cleanly without it, causing erratic resets; (2) leaving MCLR floating - it must be pulled high through a 10 kohm resistor; (3) using 5 V signals on digital I/O - the I/O are 3.3 V tolerant only and will be damaged by 5 V levels; (4) ignoring programming pins PGEDx/PGECx during PCB design - they must be accessible for MPLAB ICD/REAL ICE debug. Always validate using a Microchip development board first.
Impormasyon ng Pagsunod sa Kautusan
RoHS compliant per Microchip product page. The I-grade is industrial -40C to +85C; the E-grade variant DSPIC33EP512GM310-E/PT extends to -40C to +125C. AEC-Q100 qualification status not specified in the verified data.
