ISL83491IB - 3.3V 10Mbps RS-485/RS-422 Transceiver | Renesas
MPN: ISL83491IB ✓ NakahandaISL83491IB Ulas
An RS-485/RS-422 transceiver is an interface IC that converts between digital logic-level signals and balanced differential lines. RS-422 is commonly associated with point-to-point, full-duplex links, while RS-485 supports multipoint buses with an enable-controlled driver. The ISL83491IB combines these functions in one device and includes separate transmit and receive control in its interface arrangement. This makes it useful when a system needs flexible line-driver enable control, galvanic distance between noisy equipment, and communication over cables longer or more exposed than ordinary TTL interconnects.
The ISL83491IB is identified as a 3.3V device. The verified manufacturer product-page result identifies the family as a 3.3V, full-duplex, 10 Mbps RS-485/RS-422 transceiver with enable, while distributor records identify ISL83491IB as a 14-SOIC device. The part uses a BiCMOS implementation and a slew-rate-limited driver according to the family description. These features are significant in systems where transmitted edge rate, bus reflections, and power consumption need to be balanced rather than optimized only for maximum throughput.
Typical uses include industrial sensor and actuator networks, factory automation equipment, building-control systems, test and measurement instruments, and embedded communication modules. The 3.3V supply operation integrates directly with modern microcontroller and digital-logic rails. Designers should still verify the complete electrical limits, receiver thresholds, driver timing, and recommended external components in the manufacturer datasheet before releasing a production design.
This page combines the manufacturer family description with the available distributor records for ISL83491IB and provides practical guidance for package selection, enable control, cabling, and PCB implementation. The ISL83491IB is intended for designers who need a compact, low-power, high-speed balanced-interface solution rather than a general-purpose TTL transceiver.
A key design consideration is preserving the intended RS-485/RS-422 topology. Driver enable polarity, termination placement, common-mode behavior, and connector grounding must be checked against the system wiring. The 10 Mbps capability does not remove the need for controlled-impedance cabling, proper topology, and correct termination strategy.
Mga alternatibo na pwedeng ilagay na ISL83491IB — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok ISL83491IB (parehas na form factor at footprint) — pagkakaiba sa Package, Product Type.
ISL83491IB-T
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
ISL83491IBZ-T
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
ISL83491IBZ
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
ISL83491IB Mga Spesipikasyon
| Product Type | RS-485/RS-422 transceiver |
| Volte ng Pagbibigay | 3.3 V |
| Rate ng Data | 10 Mbps |
| Channel Configuration | 1/1 transceiver |
| Duplex Mode | Full duplex |
| Communication Standards | RS-485, RS-422 |
| Architecture | BiCMOS |
| Driver Type | Slew-rate-limited driver |
| Enable Control | Yes |
| Packhaging | 14-pin SOIC |
| Uri ng Pagpapasok | Surface mount |
Gabay sa Pin Configuration ng ISL83491IB 14-pin soic
Pin configuration para sa ISL83491IB (14-pin soic package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa ISL83491IB.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
ISL83491IB ay nararapat para sa 6 aplikasyons: Industrial Sensor Networks, Factory Automation Controllers, Building Control Systems, Test and Measurement Instruments, Embedded Communication Modules, LED Lighting Control.
Industrial Sensor Networks
The ISL83491IB suits industrial sensor and actuator networks that need a balanced differential interface on a 3.3V logic rail. Its RS-485 and RS-422 support provides noise-resistant communication over cables, while the family’s slew-rate-limited driver helps reduce ringing and radiated emissions. With a full-duplex 1/1 arrangement and data-rate capability up to 10 Mbps, it can support equipment clusters where reliable line signaling and controlled transitions are important. The design should preserve the intended bus topology, enable state, grounding arrangement, and termination strategy.
Inirekomenda
Factory Automation Controllers
The ISL83491IB can connect a 3.3V controller to RS-485 or RS-422 equipment in factory automation systems. The 10 Mbps capability accommodates higher-rate links, while the slew-rate-limited driver helps contain electromagnetic interference on factory cabling. Its 14-pin SOIC package supports compact controller boards, and the full-duplex transceiver arrangement allows transmit and receive paths to operate independently when the wiring supports that topology. Engineers should validate surge protection, common-mode range, and cable length against the completed industrial system.
Inirekomenda
Building Control Systems
The ISL83491IB is appropriate for building-control equipment that distributes commands and sensor data over balanced RS-485 links. The 3.3V supply operation fits compact embedded control boards, and the controlled driver slew rate is useful in installations where cables run near power and communications wiring. Its full-duplex operation supports dedicated differential point-to-point links, while RS-485 compatibility enables bus-oriented networks. Proper grounding, termination, protection, and separation between communications and power conductors remain essential for dependable field operation.
Inirekomenda
Test and Measurement Instruments
The ISL83491IB can provide the balanced communication link between a 3.3V instrument controller and external RS-485 or RS-422 equipment. Its data-rate capability up to 10 Mbps supports communication with remote modules and test systems, while the slew-rate-limited driver helps reduce unwanted signal energy on instrument cabling. The compact 14-pin SOIC package preserves board area for analog and measurement circuitry. For sensitive instruments, designers should check noise behavior, grounding, isolation requirements, and connector return paths before finalizing the layout.
Inirekomenda
Embedded Communication Modules
The ISL83491IB is useful in embedded communication modules that bridge a 3.3V processor or controller to RS-485 and RS-422 equipment. The full-duplex 1/1 transceiver architecture supports independent communication paths, and the 10 Mbps specification provides margin for high-speed control and data traffic. Its surface-mount 14-pin SOIC package is practical for compact modules, while the controlled edge rate helps improve EMC behavior on external cables. Firmware and hardware designers should coordinate driver-enable timing with bus turnaround and fault-recovery requirements.
Inirekomenda
LED Lighting Control
The ISL83491IB can support distributed LED-lighting controllers that exchange commands over balanced RS-485 or RS-422 wiring. Operating from 3.3V, it fits low-power control electronics, and the controlled driver slew rate helps limit electromagnetic interference in installations containing long cable runs. The full-duplex architecture can support dedicated communication paths between a master controller and lighting nodes, subject to the selected wiring topology. Because LED systems may combine power and communications conductors, designers should verify grounding, protection, and isolation to prevent fault propagation.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for ISL83491IB — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | ISL83491IB-T | ISL83491IBZ-T | ISL83491IBZ |
|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC |
| Product Type | 1/1 transceiver | 1/1 transceiver | RS-485/RS-422 transceiver | RS-485/RS-422 transceiver |
| Supply Voltage | 3.3 V | 3.3 V | 3.3 V | 3.3 V |
| Data Rate | 10 Mbps | 10 Mbps | 10 Mbps | 10 Mbps |
| Supported Standards | RS-485, RS-422 | RS-485, RS-422 | RS-485, RS-422 | RS-485, RS-422 |
| Duplex Mode | Full duplex | Full duplex | Full duplex | Full duplex |
| Driver Architecture | Slew-rate-limited BiCMOS driver | Slew-rate-limited BiCMOS driver | Slew-rate-limited BiCMOS driver | Slew-rate-limited BiCMOS driver |
| Ordering Suffix | IB | IB-T | IBZ-T | IBZ |
Pangunahing mga Pagkakaiba
- Full-duplex balanced-interface operation (kumpara saISL83491IB-T)
- 10 Mbps family capability with controlled driver edges (kumpara saISL83491IBZ-T)
- Exact ISL83491 family configuration with enable (kumpara saISL83491IBZ)
Talaan ng Disenyo
Place the transceiver and its protection components close to the connector so that differential traces remain short and symmetric. Route the two conductors of each balanced pair together, avoid stubs, and maintain consistent spacing between pairs. The controlled slew rate of the ISL83491 family helps reduce reflections, but it does not compensate for an incorrect topology or poor trace geometry.
Do not assume every ISL83491 suffix is automatically interchangeable. Confirm the 14-pin pin assignments, enable polarity, receiver thresholds, supply limits, temperature grade, and ordering interpretation for the exact device being substituted. The ISL83491IB, ISL83491IB-T, ISL83491IBZ-T, and ISL83491IBZ labels appear in related listings, but production approval should be based on the manufacturer documentation for the selected MPN.
For RS-485 buses, use a termination strategy appropriate to the cable length and topology, and place termination only where signal reflections require it. For RS-422 point-to-point links, follow the receiver and driver recommendations in the datasheet. Keep the enable function controlled during reset and startup so the driver does not contend with another transmitter on the bus.
The slew-rate-limited driver can reduce radiated emissions, but cable EMI still depends on connector shielding, cable type, grounding, and common-mode margins. Keep switching power and high-current return paths away from the balanced pair, use a solid ground reference, and evaluate the finished cable interface with the intended equipment. External surge protection should be selected to suit the installation environment.
Impormasyon ng Pagsunod sa Kautusan
Compliance status requires confirmation from the exact orderable-device documentation. The manufacturer lists the ISL83491 family device as active, but the available records do not provide a complete compliance statement for ISL83491IB.