ISL8393IB-T - Quad SPST Analog Switch | Renesas
MPN: ISL8393IB-T ✗ Tapus ng BuhayISL8393IB-T Ulas
An analog switch is an integrated circuit that routes low-frequency analog or digital signals between circuit nodes under digital control. The ISL8393IB-T belongs to the analog-switch and multiplexer hierarchy, where it sits between sensors, test points, amplifiers, converters, and system controllers. Its four SPST channels can isolate test paths, select signal sources, route instrumentation, or implement compact switching networks without using discrete mechanical relays.
Key characteristics include 1 microwatt low-power operation, maximum leakage current of 2.5 nA, and a 35 ohm on-resistance. Single-supply operation simplifies systems that only provide one positive rail, while dual-supply operation allows symmetric signal routing around ground. The 1:1 configuration indicates that each channel provides direct signal connectivity rather than converting signal polarity or multiplexing unequal impedance networks.
The ISL8393 series uses CMOS circuitry to provide low power consumption and low leakage. These characteristics suit battery-powered equipment, portable measurement systems, automated test equipment, and control systems where switched nodes should not draw substantial standby current. Maximum leakage of 2.5 nA helps preserve high-impedance sensor signals when a channel is disconnected, although exact signal integrity and switching-time limits should be confirmed from the manufacturer datasheet before high-speed or precision impedance designs are released.
Typical applications include battery-powered sensor acquisition, automated test equipment, analog signal isolation, sample-and-hold subsystems, and instrumentation routed by a microcontroller or other digital controller. A single-supply implementation can use the IC directly from a +2 V to +12 V rail, while a ±5 V system provides headroom for bipolar signals when the device is operated within the specified ±2 V to ±6 V range.
Layout should keep the analog signal traces short and provide a solid ground reference. The unused control inputs must be driven to defined logic levels so that no switch remains partially on, while supply bypassing should be placed close to the device. Signal traces should avoid routing alongside noisy switching or digital return paths, especially where the selected channel drives a high-impedance sensor.
This page combines the manufacturer family specifications, package information, sourcing context, replacement analysis, comparison tables, and application guidance into one engineering-oriented reference for evaluating the ISL8393IB-T.
Mga alternatibo na pwedeng ilagay na ISL8393IB-T — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok ISL8393IB-T (parehas na form factor at footprint) — pagkakaiba sa On-Resistance, Package, Dual-Supply Operating Range, Switch Configuration.
ISL8393IBZ-T
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
ISL8393IBZ
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
ISL8393IB
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →ISL8393IB-T Mga Pinakamataas na Rating at Electrical Characteristics
| Device Type | CMOS precision quad analog switch |
| Number of Channels | 4 circuits |
| Switch Configuration | 4 x SPST |
| Signal Configuration | 1:1 |
| On-Resistance | 35 ohm |
| Single-Supply Voltage Range | +2 V to +12 V |
| Dual-Supply Voltage Range | ±2 V to ±6 V |
| Low Power Consumption | 1 uW |
| Maximum Leakage Current | 2.5 nA |
| Packhaging | 16-lead SOIC |
| Uri ng Pagpapasok | Surface mount |
| Logic | CMOS |
| Tindminan RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
Gabay sa Pin Configuration ng ISL8393IB-T 16-lead soic
Pin configuration para sa ISL8393IB-T (16-lead soic package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa ISL8393IB-T.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
ISL8393IB-T ay nararapat para sa 6 aplikasyons: Battery-Powered Sensor Acquisition, Automated Test Equipment Signal Routing, Portable Measurement Instruments, Analog Signal Isolation, Dual-Supply Bipolar Routing, Sample-and-Hold Front Ends.
Battery-Powered Sensor Acquisition
The ISL8393IB-T is well suited to battery-powered sensor acquisition because the ISL8393 family is specified for 1 uW low-power consumption and leakage current up to 2.5 nA. Place the four SPST channels between sensor outputs and a shared measurement amplifier or ADC input, using each channel to isolate an inactive sensor or select a test path. The 35 ohm on-resistance can be acceptable for many sensor outputs, while the low-leakage characteristic helps preserve signals from high-impedance sources. Use the +2 V to +12 V single-supply range and verify the selected channel’s signal amplitude against the analog voltage limits.
Inirekomenda
Automated Test Equipment Signal Routing
Use the ISL8393IB-T to route instrument signals among test nodes, fixture contacts, or DUT pins in automated test equipment. Its four independent SPST channels provide flexible isolation and direct 1:1 routing, while the 35 ohm resistance should be included in the test-path impedance budget. The device can operate from a single +2 V to +12 V source or from ±2 V to ±6 V rails, allowing the same switching architecture to support both unipolar and bipolar fixtures. Place switch traces away from high-current DUT paths to reduce coupling, and verify control levels and switched voltage limits before connecting external test equipment.
Inirekomenda
Portable Measurement Instruments
The ISL8393IB-T supports portable measurement instruments where low standby power, compact packaging, and flexible signal selection are important. Its 16-lead SOIC package permits conventional surface-mount assembly, while four SPST channels can select between a sensor, calibration source, or diagnostic path. The 1 uW low-power figure and 2.5 nA maximum leakage help limit the impact of the switch on battery-operated instruments and high-impedance measurement nodes. Keep the analog input traces short, provide a low-impedance ground reference, and account for the 35 ohm insertion resistance when calculating measurement-system sensitivity.
Inirekomenda
Analog Signal Isolation
The ISL8393IB-T can isolate one analog branch from another when leakage and power consumption are more important than very low on-resistance. Each of the four SPST channels can disconnect a source when it is not selected, helping prevent loading or unintended signal propagation. This is useful in multiplexed front ends, instrumentation, and control interfaces where disabled branches must not disturb an active measurement. The maximum leakage current of 2.5 nA is the principal published leakage figure to evaluate; the complete datasheet should be checked for actual off-state leakage across temperature and voltage before using the switch with exceptionally high source impedances.
Inirekomenda
Dual-Supply Bipolar Routing
Operate the ISL8393IB-T from ±2 V to ±6 V when the system must switch signals centered around ground. The dual-supply configuration supports bipolar instrumentation and control signals without biasing the selected path around a positive midpoint. The 35 ohm on-resistance is the principal trade-off, so impedance-sensitive stages should place gain or buffering ahead of the switch when insertion resistance would reduce accuracy. Maintain symmetrical supply decoupling and route ground returns carefully to prevent supply-current transients from appearing as signal errors on the routed node.
Inirekomenda
Sample-and-Hold Front Ends
The ISL8393IB-T can connect or disconnect a source within a sample-and-hold front end by using the SPST channels to control which signal reaches a sampling capacitor and buffer. The low 1 uW power figure suits compact acquisition systems, and the four channels permit source selection around a shared analog node. Care is required because the switch’s 35 ohm on-resistance interacts with capacitor charging time, and leakage into a high-impedance hold capacitor may cause droop. Place the switch and sampling network close to the buffer, use a defined control state during acquisition and hold intervals, and check the complete leakage and voltage-rating specifications.
Inirekomenda
Impormasyon ng Talumpati sa Engineering for ISL8393IB-T — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | ISL8393IBZ-T | ISL8393IBZ | ISL8393IB |
|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 16-lead SOIC | 16-lead SOIC - same | 16-lead SOIC - same | 16-lead SOIC - same |
| Number of Switches | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Switch Configuration | 4 x SPST | 4 x SPST | 4 x SPST | 4 x SPST |
| Signal Configuration | 1:1 | 1:1 | 1:1 | 1:1 |
Pangunahing mga Pagkakaiba
- Documented quad-SPST routing with 1:1 signal configuration (kumpara saISL8393IB)
- Same-family terminal and package compatibility (kumpara saISL8393IBZ-T)
- Low-power operation for portable analog routing (kumpara saISL8393IBZ)
Talaan ng Disenyo
Route each switched analog signal as a short, direct trace between the ISL8393IB-T terminal and its destination. Avoid sharing narrow signal segments with digital control or return-current paths. Place the supply bypass capacitor close to the device and use a low-impedance ground plane so the four switching actions do not inject supply disturbance into sensitive analog nodes.
Include the 35 ohm on-resistance when calculating source loading and voltage division. For a high-impedance source, the switch and amplifier input form a divider that can reduce signal amplitude. If the resulting error is excessive, place a low-input-impedance buffer before the switch or select a lower-resistance switching device designed for the signal bandwidth.
Never leave a control input floating. Drive every select input to a defined logic level so that each SPST channel is unambiguously on or off. Check the allowed logic thresholds and input voltages against the selected supply configuration in the manufacturer datasheet, especially when the controller operates at a voltage different from the analog-switch supply.
Single-supply operation uses the +2 V to +12 V range, while dual-supply operation uses ±2 V to ±6 V. Do not infer a permissible negative rail from the positive single-supply limit. Keep both rails within the specified limits, account for the 1 uW low-power family rating in the standby budget, and verify actual system consumption with the control states used in production.
Impormasyon ng Pagsunod sa Kautusan
The exact suffix-specific environmental and material-compliance status is not established by the manufacturer product information for ISL8393IB-T. RoHS and REACH should be confirmed against the relevant manufacturer declaration or lot documentation before qualification.