Renesas Electronics

ISL8393IB-T - Quad SPST Analog Switch | Renesas

MPN: ISL8393IB-T ✗ Son Kullanım Zamanı
+2 V to +12 V Vdss 2.5 nA Id 35 ohm Rds(on) 16-lead SOIC Package
MOQ: 1 |

ISL8393IB-T Genel Bakış

Renesas Electronics ISL8393IB-T is a CMOS precision quad analog switch containing four independent single-pole single-throw channels, with a 1:1 signal configuration, 35 ohm on-resistance, and a 16-lead SOIC package. The device operates from a single +2 V to +12 V supply or from dual ±2 V to ±6 V supplies.

An analog switch is an integrated circuit that routes low-frequency analog or digital signals between circuit nodes under digital control. The ISL8393IB-T belongs to the analog-switch and multiplexer hierarchy, where it sits between sensors, test points, amplifiers, converters, and system controllers. Its four SPST channels can isolate test paths, select signal sources, route instrumentation, or implement compact switching networks without using discrete mechanical relays.

Key characteristics include 1 microwatt low-power operation, maximum leakage current of 2.5 nA, and a 35 ohm on-resistance. Single-supply operation simplifies systems that only provide one positive rail, while dual-supply operation allows symmetric signal routing around ground. The 1:1 configuration indicates that each channel provides direct signal connectivity rather than converting signal polarity or multiplexing unequal impedance networks.

The ISL8393 series uses CMOS circuitry to provide low power consumption and low leakage. These characteristics suit battery-powered equipment, portable measurement systems, automated test equipment, and control systems where switched nodes should not draw substantial standby current. Maximum leakage of 2.5 nA helps preserve high-impedance sensor signals when a channel is disconnected, although exact signal integrity and switching-time limits should be confirmed from the manufacturer datasheet before high-speed or precision impedance designs are released.

Typical applications include battery-powered sensor acquisition, automated test equipment, analog signal isolation, sample-and-hold subsystems, and instrumentation routed by a microcontroller or other digital controller. A single-supply implementation can use the IC directly from a +2 V to +12 V rail, while a ±5 V system provides headroom for bipolar signals when the device is operated within the specified ±2 V to ±6 V range.

Layout should keep the analog signal traces short and provide a solid ground reference. The unused control inputs must be driven to defined logic levels so that no switch remains partially on, while supply bypassing should be placed close to the device. Signal traces should avoid routing alongside noisy switching or digital return paths, especially where the selected channel drives a high-impedance sensor.

This page combines the manufacturer family specifications, package information, sourcing context, replacement analysis, comparison tables, and application guidance into one engineering-oriented reference for evaluating the ISL8393IB-T.

Drop-in alternatifler için ISL8393IB-T — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.

Bu Serideki Variantlar

Yedek parça uyumlu olan aynı serideki modeller ISL8393IB-T (aynı form faktörü ve ayağa oturma) — farklı olan On-Resistance, Package, Dual-Supply Operating Range, Switch Configuration.

Renesas Electronics
Package: 16-pin SOIC
Dual-Supply Operating Range: +/-2 V to +/-6 V
İle Karşılaştır ISL8393IB-T →
Renesas Electronics
On-Resistance: 20 ohm typical, 35 ohm maximum
Package: 16-pin SOIC
Dual-Supply Operating Range: ±2 V to ±6 V
İle Karşılaştır ISL8393IB-T →

ISL8393IBZ-T

✅ Yerleştirme
📦 16-lead SOIC
Same ISL8393 family and 16-pin SOIC terminal arrangement; Z suffix changes ordering treatment, while exact electrical deltas are .

📋 Katalogda Olmayan Referans Alternatifi

ISL8393IBZ

✅ Yerleştirme
📦 16-lead SOIC
Same 16-pin SOIC package and documented compatible terminals; exact on-resistance, leakage, and logic differences are .

📋 Katalogda Olmayan Referans Alternatifi

ISL8393IB

✅ Yerleştirme
Renesas Electronics
📦 16-lead SOIC
4 circuits · Quad SPST · 4 separately controlled channels · +2 V to +12 V · ±2 V to ±6 V · CMOS · 20 ohm typical, 35 ohm maximum · 1 ohm

Fiyat için iletişime geçin

Veri Şablonunu Görüntüle →

ISL8393IB-T Maksimum Değerlendirmeler & Elektriksel Özellikler

Device Type CMOS precision quad analog switch
Number of Channels 4 circuits
Switch Configuration 4 x SPST
Signal Configuration 1:1
On-Resistance 35 ohm
Single-Supply Voltage Range +2 V to +12 V
Dual-Supply Voltage Range ±2 V to ±6 V
Low Power Consumption 1 uW
Maximum Leakage Current 2.5 nA
Paket 16-lead SOIC
Montaj Türü Surface mount
Logic CMOS
RoHS Durumu unknown
REACH Status unknown
AEC-Q100 Qualification not_applicable

ISL8393IB-T 16-lead soic Pin Yapısı Kılavuzu

ISL8393IB-T (16-lead soic paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.

16-lead soic paket pin çizelgesi için ISL8393IB-T

Ayrıntılı pin çıkış verisi mevcut değil: ISL8393IB-T.

Aşağıdaki veri sayfası tam pin konfigürasyonu için.

Tipik Uygulamalar

ISL8393IB-T için uygundur 6 uygulamas: Battery-Powered Sensor Acquisition, Automated Test Equipment Signal Routing, Portable Measurement Instruments, Analog Signal Isolation, Dual-Supply Bipolar Routing, Sample-and-Hold Front Ends.

🧩

Battery-Powered Sensor Acquisition

The ISL8393IB-T is well suited to battery-powered sensor acquisition because the ISL8393 family is specified for 1 uW low-power consumption and leakage current up to 2.5 nA. Place the four SPST channels between sensor outputs and a shared measurement amplifier or ADC input, using each channel to isolate an inactive sensor or select a test path. The 35 ohm on-resistance can be acceptable for many sensor outputs, while the low-leakage characteristic helps preserve signals from high-impedance sources. Use the +2 V to +12 V single-supply range and verify the selected channel’s signal amplitude against the analog voltage limits.

🏭

Automated Test Equipment Signal Routing

Use the ISL8393IB-T to route instrument signals among test nodes, fixture contacts, or DUT pins in automated test equipment. Its four independent SPST channels provide flexible isolation and direct 1:1 routing, while the 35 ohm resistance should be included in the test-path impedance budget. The device can operate from a single +2 V to +12 V source or from ±2 V to ±6 V rails, allowing the same switching architecture to support both unipolar and bipolar fixtures. Place switch traces away from high-current DUT paths to reduce coupling, and verify control levels and switched voltage limits before connecting external test equipment.

📱

Portable Measurement Instruments

The ISL8393IB-T supports portable measurement instruments where low standby power, compact packaging, and flexible signal selection are important. Its 16-lead SOIC package permits conventional surface-mount assembly, while four SPST channels can select between a sensor, calibration source, or diagnostic path. The 1 uW low-power figure and 2.5 nA maximum leakage help limit the impact of the switch on battery-operated instruments and high-impedance measurement nodes. Keep the analog input traces short, provide a low-impedance ground reference, and account for the 35 ohm insertion resistance when calculating measurement-system sensitivity.

🔧

Analog Signal Isolation

The ISL8393IB-T can isolate one analog branch from another when leakage and power consumption are more important than very low on-resistance. Each of the four SPST channels can disconnect a source when it is not selected, helping prevent loading or unintended signal propagation. This is useful in multiplexed front ends, instrumentation, and control interfaces where disabled branches must not disturb an active measurement. The maximum leakage current of 2.5 nA is the principal published leakage figure to evaluate; the complete datasheet should be checked for actual off-state leakage across temperature and voltage before using the switch with exceptionally high source impedances.

⚡

Dual-Supply Bipolar Routing

Operate the ISL8393IB-T from ±2 V to ±6 V when the system must switch signals centered around ground. The dual-supply configuration supports bipolar instrumentation and control signals without biasing the selected path around a positive midpoint. The 35 ohm on-resistance is the principal trade-off, so impedance-sensitive stages should place gain or buffering ahead of the switch when insertion resistance would reduce accuracy. Maintain symmetrical supply decoupling and route ground returns carefully to prevent supply-current transients from appearing as signal errors on the routed node.

📺

Sample-and-Hold Front Ends

The ISL8393IB-T can connect or disconnect a source within a sample-and-hold front end by using the SPST channels to control which signal reaches a sampling capacitor and buffer. The low 1 uW power figure suits compact acquisition systems, and the four channels permit source selection around a shared analog node. Care is required because the switch’s 35 ohm on-resistance interacts with capacitor charging time, and leakage into a high-impedance hold capacitor may cause droop. Place the switch and sampling network close to the buffer, use a defined control state during acquisition and hold intervals, and check the complete leakage and voltage-rating specifications.

What is the ISL8393IB-T?
The ISL8393IB-T is a four-channel CMOS analog switch with independent SPST contacts, a 1:1 signal configuration, 35 ohm on-resistance, and a 16-lead SOIC package. According to the Renesas ISL8393 product information, the Intersil ISL8391-ISL8393 family is designed for low-voltage single- or dual-supply operation. Each channel can route or isolate an analog signal under a separate digital control input.
What is the operating voltage range of ISL8393IB-T?
The ISL8393IB-T operates from +2 V to +12 V with a single supply or from ±2 V to ±6 V with dual supplies. Renesas describes the ISL8391-ISL8393 devices as low-voltage analog switches intended for both supply arrangements. The single-supply range supports portable and embedded systems, while the dual-supply range permits bipolar signal routing when the full 35 ohm on-resistance remains acceptable.
What are the key specifications of ISL8393IB-T that engineers should know?
The principal ISL8393IB-T specifications are four independent SPST channels, 1:1 signal routing, 35 ohm on-resistance, and a 16-lead SOIC package. The device also supports +2 V to +12 V single-supply operation, ±2 V to ±6 V dual-supply operation, 1 uW low-power consumption, and 2.5 nA maximum leakage current. These parameters position it for low-voltage analog routing rather than high-speed RF switching.
Where can I download the ISL8393IB-T datasheet PDF?
The ISL8393IB-T datasheet can be accessed through the Renesas ISL8393 part-details page or the linked Intersil datasheet documents. The manufacturer page describes the ISL8393IB as a low-voltage quad SPST analog switch, while the document listings identify a 12-page PDF. Use the manufacturer document for design decisions and the Renesas part-details page to confirm lifecycle and ordering information.
Where can I find the ISL8393IB-T pinout?
Use the pin-description table and package drawing in the ISL8393IB manufacturer datasheet to assign the 16 SOIC pins correctly. The verified product information confirms a 16-lead SOIC package but does not reproduce the pin names, so no pin mapping is asserted here. In particular, verify the four control inputs, supply pins, ground connection, and eight switch terminals against the exact datasheet before PCB routing.
Can ISL8393IB-T switch bipolar signals?
Yes, the ISL8393IB-T can route bipolar signals when operated from a dual supply in the ±2 V to ±6 V range. Renesas specifically describes operation from single +2 V to +12 V supplies or dual supplies up to ±6 V. The 35 ohm on-resistance must be included in the signal-path loss calculation, and the selected channel should remain within its rated analog voltage range.
Is ISL8393IB-T suitable for battery-powered equipment?
The ISL8393IB-T is suitable for battery-powered equipment because the Renesas family specification identifies 1 uW low-power consumption and a 2.5 nA maximum leakage current. These characteristics help reduce switching-node loading and standby drain in portable instruments, sensor interfaces, and battery-operated test systems. The complete power budget should also include the control logic state and leakage into downstream circuitry.
What can replace ISL8393IB-T?
ISL8393IBZ-T and ISL8393IBZ are the closest documented same-family drop-in candidates for ISL8393IB-T, while ISL8393IB without the tape-and-reel suffix is another package-compatible ordering form. The available comparison information reports consistent terminal and package arrangements, but engineers should verify control polarity, on-resistance, leakage, and supply limits against the exact manufacturer datasheet before production substitution.
Can ISL8393IBZ-T replace ISL8393IB-T?
Yes, ISL8393IBZ-T is presented as a package- and terminal-compatible replacement candidate for ISL8393IB-T. The comparison identifies consistent functional characteristics and a 16-pin SOIC format, which supports drop-in reuse of the PCB footprint. Final approval should include a check of the exact control-input logic, supply-voltage ratings, on-resistance, leakage, and operating-temperature limits.
What is the best Renesas equivalent for ISL8393IB-T?
ISL8393IBZ-T is the closest Renesas-listed equivalent candidate because it belongs to the same ISL8393 family and uses the same 16-pin SOIC format. It adds the Z suffix associated with a different ordering or packaging treatment rather than a demonstrated change in the core quad-SPST function. Confirm ordering, shipment form, and device markings with the manufacturer before treating it as an unqualified replacement.
When should I choose ISL8393IB-T over another ISL8393 variant?
Choose ISL8393IB-T when the design requires the 35 ohm, four-channel SPST switch in a 16-lead SOIC package and the -T ordering form matches the required production packing. Choose ISL8393IBZ-T when its documented ordering and lead-free treatment better fit the assembly process, after confirming equivalent electrical ratings. Choose plain ISL8393IB when a non -T packaging form is appropriate for the assembly plan.
ISL8393IB-T vs ISL8393IBZ-T - which is better for a new design?
ISL8393IB-T and ISL8393IBZ-T are functionally close choices for the same 16-pin SOIC design, and the available comparison reports compatible terminals and packages. ISL8393IB-T is appropriate when its ordering code and packing align with the production process; ISL8393IBZ-T may be preferable when its lead-free ordering treatment is required. Verify the exact suffix-specific datasheet ratings before releasing either device.
What is the difference between ISL8393IB and ISL8393IB-T?
The verified ordering information associates ISL8393IB-T with the 16-SOIC, 35-ohm quad-SPST switch in tape-and-reel form, while ISL8393IB denotes the base part ordering code. Their core device description is the same, but procurement engineers should treat suffix-specific packing, traceability, and marking requirements separately. The manufacturer datasheet and ordering page should control any substitution decision.
Where to buy ISL8393IB-T online?
Use the Request a Quote form on this page to request ISL8393IB-T availability, current commercial terms, and shipment options. The part is a 4-circuit, 1:1, 35-ohm analog switch in a 16-SOIC package. Quotation requests provide a direct channel for confirming the exact -T ordering code, quantity, and production delivery schedule without relying on a generic product listing.
What is the price and lead time for ISL8393IB-T?
The current commercial price and lead time for ISL8393IB-T should be requested through the Request a Quote form on this page. The component is listed as a 4-circuit, 1:1, 35-ohm, 16-SOIC analog switch, but quotation and availability can vary with order quantity, shipment form, and market conditions. No static price or unconfirmed lead time should be used for production planning.
Is ISL8393IB-T in stock?
Stock status for the exact ISL8393IB-T ordering code should be confirmed through the Request a Quote form on this page. The manufacturer product page states that support is limited to customers who have already adopted these products, so lifecycle and supply should be checked against the planned volume and date code. Use the requested quotation response to establish current availability for the required quantity.

Mühendislik referans verileri: ISL8393IB-T — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.

Seçim Kılavuzu

Choose ISL8393IB-T for a new design when the required switching function is four independent 1:1 SPST channels with 35 ohm on-resistance in a 16-lead SOIC package, and the -T ordering form matches the assembly process. The device is particularly appropriate for low-voltage single- or dual-supply systems where low power and low leakage matter. ISL8393IBZ-T is the closest same-family option when its Z ordering treatment and documentation match the required sourcing and assembly conditions; verify control polarity and electrical limits before release. ISL8393IBZ offers the same documented family and package arrangement with a different ordering form, while plain ISL8393IB is a direct base-code option when the desired packing differs. No cross-brand drop-in candidate was established, so a new PCB should not assume third-party compatibility. For production approval, confirm the exact suffix-specific datasheet, lifecycle position, temperature rating, switched-voltage limits, and insertion-loss budget.

Alternatiflerle Karşılaştırma

Parametre Bu Ürün ISL8393IBZ-T ISL8393IBZ ISL8393IB
Brand Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics
Package 16-lead SOIC 16-lead SOIC - same 16-lead SOIC - same 16-lead SOIC - same
Number of Switches 4 circuits 4 circuits 4 circuits 4 circuits
Switch Configuration 4 x SPST 4 x SPST 4 x SPST 4 x SPST
Signal Configuration 1:1 1:1 1:1 1:1

Ana Farklılayıcılar

  • Documented quad-SPST routing with 1:1 signal configuration (karşılaştırma:ISL8393IB)
  • Same-family terminal and package compatibility (karşılaştırma:ISL8393IBZ-T)
  • Low-power operation for portable analog routing (karşılaştırma:ISL8393IBZ)

Tasarım Notları

Route each switched analog signal as a short, direct trace between the ISL8393IB-T terminal and its destination. Avoid sharing narrow signal segments with digital control or return-current paths. Place the supply bypass capacitor close to the device and use a low-impedance ground plane so the four switching actions do not inject supply disturbance into sensitive analog nodes.

Include the 35 ohm on-resistance when calculating source loading and voltage division. For a high-impedance source, the switch and amplifier input form a divider that can reduce signal amplitude. If the resulting error is excessive, place a low-input-impedance buffer before the switch or select a lower-resistance switching device designed for the signal bandwidth.

Never leave a control input floating. Drive every select input to a defined logic level so that each SPST channel is unambiguously on or off. Check the allowed logic thresholds and input voltages against the selected supply configuration in the manufacturer datasheet, especially when the controller operates at a voltage different from the analog-switch supply.

Single-supply operation uses the +2 V to +12 V range, while dual-supply operation uses ±2 V to ±6 V. Do not infer a permissible negative rail from the positive single-supply limit. Keep both rails within the specified limits, account for the 1 uW low-power family rating in the standby budget, and verify actual system consumption with the control states used in production.

Uyumluluk Bilgisi

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Kadmiyumdan Arınmış
Unknown
Klorofillerden Arınmış
Unknown
Çatışma Minerali
Unknown

The exact suffix-specific environmental and material-compliance status is not established by the manufacturer product information for ISL8393IB-T. RoHS and REACH should be confirmed against the relevant manufacturer declaration or lot documentation before qualification.

Veri doğrulanma tarihi: 2026-11-10 — XAIPART bileşen mühendislik ekibi tarafından doğrulanmış ve derlenmiş veri

İlgili Aramalar

ISL8393IB-T datasheet ISL8393IB-T pinout ISL8393IB-T datasheet pdf ISL8393IB-T equivalent ISL8393IB-T replacement ISL8393IB-T cross reference ISL8393IB-T price ISL8393IB-T stock Renesas ISL8393IB-T ISL8393IB-T 16 SOIC ISL8393IB-T 35 ohm ISL8393IB-T application circuit ISL8393IB-T vs ISL8393IBZ-T ISL8393IB-T footprint ISL8393IB-T supply voltage

İlgili Bileşenler ve Terimler

Renesas Electronics Intersil ISL8393IB-T ISL8393IBZ-T ISL8393IBZ ISL8393IB analog switch quad analog switch SPST switch single-pole single-throw CMOS interface IC multiplexer signal isolation on-resistance leakage current single supply dual supply bipolar signal routing battery-powered equipment automated test equipment 16-lead SOIC SOIC family surface-mount package
Hızlı Teklif RFQ
Detayları tam doldurun — satış ekibimiz 24 saat içinde yanıt verecek
Parça Numarası Üretici Paket QTY Hedef Fiyat Genişletilmiş
✓
Teklif gönderildi!

24 saat içinde e-postanıza yanıt vereceğiz

1
RFQ Gönderildi
2
Teklif Alındı
3
Sipariş Yerleştirildi
4
Ödeme
5
Gönderildi
6
Teslim Edildi
RFQ Detaylarını Görüntüle