ISL8393IB-T - Quad SPST Analog Switch | Renesas
部品番号: ISL8393IB-T ✗ 生産終了ISL8393IB-T 概要
An analog switch is an integrated circuit that routes low-frequency analog or digital signals between circuit nodes under digital control. The ISL8393IB-T belongs to the analog-switch and multiplexer hierarchy, where it sits between sensors, test points, amplifiers, converters, and system controllers. Its four SPST channels can isolate test paths, select signal sources, route instrumentation, or implement compact switching networks without using discrete mechanical relays.
Key characteristics include 1 microwatt low-power operation, maximum leakage current of 2.5 nA, and a 35 ohm on-resistance. Single-supply operation simplifies systems that only provide one positive rail, while dual-supply operation allows symmetric signal routing around ground. The 1:1 configuration indicates that each channel provides direct signal connectivity rather than converting signal polarity or multiplexing unequal impedance networks.
The ISL8393 series uses CMOS circuitry to provide low power consumption and low leakage. These characteristics suit battery-powered equipment, portable measurement systems, automated test equipment, and control systems where switched nodes should not draw substantial standby current. Maximum leakage of 2.5 nA helps preserve high-impedance sensor signals when a channel is disconnected, although exact signal integrity and switching-time limits should be confirmed from the manufacturer datasheet before high-speed or precision impedance designs are released.
Typical applications include battery-powered sensor acquisition, automated test equipment, analog signal isolation, sample-and-hold subsystems, and instrumentation routed by a microcontroller or other digital controller. A single-supply implementation can use the IC directly from a +2 V to +12 V rail, while a ±5 V system provides headroom for bipolar signals when the device is operated within the specified ±2 V to ±6 V range.
Layout should keep the analog signal traces short and provide a solid ground reference. The unused control inputs must be driven to defined logic levels so that no switch remains partially on, while supply bypassing should be placed close to the device. Signal traces should avoid routing alongside noisy switching or digital return paths, especially where the selected channel drives a high-impedance sensor.
This page combines the manufacturer family specifications, package information, sourcing context, replacement analysis, comparison tables, and application guidance into one engineering-oriented reference for evaluating the ISL8393IB-T.
ドロップイン代替品: ISL8393IB-T — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: ISL8393IB-T (同一形状・フットプリント) — 相違点: On-Resistance, Package, Dual-Supply Operating Range, Switch Configuration.
ISL8393IBZ-T
✅ ドロップイン📋 参考代替品(カタログ未掲載)
ISL8393IBZ
✅ ドロップイン📋 参考代替品(カタログ未掲載)
ISL8393IB
✅ ドロップイン価格はお問い合わせください
データシートを見る →ISL8393IB-T 最大定格&電気的特性
| Device Type | CMOS precision quad analog switch |
| Number of Channels | 4 circuits |
| Switch Configuration | 4 x SPST |
| Signal Configuration | 1:1 |
| On-Resistance | 35 ohm |
| Single-Supply Voltage Range | +2 V to +12 V |
| Dual-Supply Voltage Range | ±2 V to ±6 V |
| Low Power Consumption | 1 uW |
| Maximum Leakage Current | 2.5 nA |
| パッケージ | 16-lead SOIC |
| 実装タイプ | Surface mount |
| Logic | CMOS |
| RoHS ステータス | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
ISL8393IB-T 16-lead soic ピン配置ガイド
ISL8393IB-T (16-lead soic パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: ISL8393IB-T.
詳細は データシート をご参照ください。
主な用途
ISL8393IB-T の用途: 6 件s: Battery-Powered Sensor Acquisition, Automated Test Equipment Signal Routing, Portable Measurement Instruments, Analog Signal Isolation, Dual-Supply Bipolar Routing, Sample-and-Hold Front Ends.
Battery-Powered Sensor Acquisition
The ISL8393IB-T is well suited to battery-powered sensor acquisition because the ISL8393 family is specified for 1 uW low-power consumption and leakage current up to 2.5 nA. Place the four SPST channels between sensor outputs and a shared measurement amplifier or ADC input, using each channel to isolate an inactive sensor or select a test path. The 35 ohm on-resistance can be acceptable for many sensor outputs, while the low-leakage characteristic helps preserve signals from high-impedance sources. Use the +2 V to +12 V single-supply range and verify the selected channel’s signal amplitude against the analog voltage limits.
おすすめ
Automated Test Equipment Signal Routing
Use the ISL8393IB-T to route instrument signals among test nodes, fixture contacts, or DUT pins in automated test equipment. Its four independent SPST channels provide flexible isolation and direct 1:1 routing, while the 35 ohm resistance should be included in the test-path impedance budget. The device can operate from a single +2 V to +12 V source or from ±2 V to ±6 V rails, allowing the same switching architecture to support both unipolar and bipolar fixtures. Place switch traces away from high-current DUT paths to reduce coupling, and verify control levels and switched voltage limits before connecting external test equipment.
おすすめ
Portable Measurement Instruments
The ISL8393IB-T supports portable measurement instruments where low standby power, compact packaging, and flexible signal selection are important. Its 16-lead SOIC package permits conventional surface-mount assembly, while four SPST channels can select between a sensor, calibration source, or diagnostic path. The 1 uW low-power figure and 2.5 nA maximum leakage help limit the impact of the switch on battery-operated instruments and high-impedance measurement nodes. Keep the analog input traces short, provide a low-impedance ground reference, and account for the 35 ohm insertion resistance when calculating measurement-system sensitivity.
おすすめ
Analog Signal Isolation
The ISL8393IB-T can isolate one analog branch from another when leakage and power consumption are more important than very low on-resistance. Each of the four SPST channels can disconnect a source when it is not selected, helping prevent loading or unintended signal propagation. This is useful in multiplexed front ends, instrumentation, and control interfaces where disabled branches must not disturb an active measurement. The maximum leakage current of 2.5 nA is the principal published leakage figure to evaluate; the complete datasheet should be checked for actual off-state leakage across temperature and voltage before using the switch with exceptionally high source impedances.
おすすめ
Dual-Supply Bipolar Routing
Operate the ISL8393IB-T from ±2 V to ±6 V when the system must switch signals centered around ground. The dual-supply configuration supports bipolar instrumentation and control signals without biasing the selected path around a positive midpoint. The 35 ohm on-resistance is the principal trade-off, so impedance-sensitive stages should place gain or buffering ahead of the switch when insertion resistance would reduce accuracy. Maintain symmetrical supply decoupling and route ground returns carefully to prevent supply-current transients from appearing as signal errors on the routed node.
おすすめ
Sample-and-Hold Front Ends
The ISL8393IB-T can connect or disconnect a source within a sample-and-hold front end by using the SPST channels to control which signal reaches a sampling capacitor and buffer. The low 1 uW power figure suits compact acquisition systems, and the four channels permit source selection around a shared analog node. Care is required because the switch’s 35 ohm on-resistance interacts with capacitor charging time, and leakage into a high-impedance hold capacitor may cause droop. Place the switch and sampling network close to the buffer, use a defined control state during acquisition and hold intervals, and check the complete leakage and voltage-rating specifications.
おすすめ
エンジニアリング参考データ: ISL8393IB-T — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | ISL8393IBZ-T | ISL8393IBZ | ISL8393IB |
|---|---|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics |
| Package | 16-lead SOIC | 16-lead SOIC - same | 16-lead SOIC - same | 16-lead SOIC - same |
| Number of Switches | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Switch Configuration | 4 x SPST | 4 x SPST | 4 x SPST | 4 x SPST |
| Signal Configuration | 1:1 | 1:1 | 1:1 | 1:1 |
主な差別化要因
- Documented quad-SPST routing with 1:1 signal configuration (vs ISL8393IB)
- Same-family terminal and package compatibility (vs ISL8393IBZ-T)
- Low-power operation for portable analog routing (vs ISL8393IBZ)
設計ノート
Route each switched analog signal as a short, direct trace between the ISL8393IB-T terminal and its destination. Avoid sharing narrow signal segments with digital control or return-current paths. Place the supply bypass capacitor close to the device and use a low-impedance ground plane so the four switching actions do not inject supply disturbance into sensitive analog nodes.
Include the 35 ohm on-resistance when calculating source loading and voltage division. For a high-impedance source, the switch and amplifier input form a divider that can reduce signal amplitude. If the resulting error is excessive, place a low-input-impedance buffer before the switch or select a lower-resistance switching device designed for the signal bandwidth.
Never leave a control input floating. Drive every select input to a defined logic level so that each SPST channel is unambiguously on or off. Check the allowed logic thresholds and input voltages against the selected supply configuration in the manufacturer datasheet, especially when the controller operates at a voltage different from the analog-switch supply.
Single-supply operation uses the +2 V to +12 V range, while dual-supply operation uses ±2 V to ±6 V. Do not infer a permissible negative rail from the positive single-supply limit. Keep both rails within the specified limits, account for the 1 uW low-power family rating in the standby budget, and verify actual system consumption with the control states used in production.
コンプライアンス情報
The exact suffix-specific environmental and material-compliance status is not established by the manufacturer product information for ISL8393IB-T. RoHS and REACH should be confirmed against the relevant manufacturer declaration or lot documentation before qualification.