LM2903M/NOPB - Dual Open-Collector Comparator | Texas Instruments
MPN: LM2903M/NOPB ✓ NakahandaLM2903M/NOPB Ulas
An analog comparator is a signal-conditioning semiconductor that compares two input voltages and changes its output state when one input exceeds the other. The LM2903 belongs to the comparator hierarchy within analog and mixed-signal semiconductors. A differential comparator can operate from a single supply or split supply, allowing it to compare signals near ground, bipolar signals, or thresholds referenced to a supply rail.
The LM2903M/NOPB provides two independent low-power, low-offset comparators in one package. Its open-collector outputs are designed for wired-interface use and require an external pull-up resistor to establish a positive logic high when the output transistor is off. The listed propagation delay is 1.5 microseconds, making the device suitable for threshold detection, level translation, relay or solenoid driving, and general industrial control functions where microsecond-scale decision speed is sufficient.
A broad supply range is useful in equipment operating from industrial or automotive-style voltage rails. The -40°C to 85°C temperature range supports industrial and extended-temperature environments, although the specific LM2903M/NOPB orderable status and quality qualification should be checked for each deployment. The 8-pin SOIC package is a standard surface-mount footprint that is larger than contemporary compact packages but remains convenient for hand assembly, prototyping, and through-hole-style external pull-up routing.
Typical uses include monitoring a sensor against an adjustable threshold, detecting overvoltage or undervoltage conditions, converting an analog level into a logic event, and providing two independent comparisons in control, instrumentation, or power-supply systems. Because the outputs are open collector, multiple devices or nodes can share a pull-up arrangement when the electrical conditions permit.
Designers should account for input common-mode range, output pull-up requirements, supply decoupling, and the effect of input bias current when selecting threshold resistors. Keep comparator inputs away from switching-node currents and provide a stable local ground reference. The open-collector nodes should have pull-up resistors selected for the required logic voltage, sink-current budget, rise-time target, and system power budget.
This page combines the manufacturer's ordering information, a source-grounded parameter summary, application engineering guidance, and package-level replacement analysis. It also identifies the design trade-offs that matter when comparing the LM2903M/NOPB with related dual comparators rather than relying only on basic device descriptions.
Mga alternatibo na pwedeng ilagay na LM2903M/NOPB — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok LM2903M/NOPB (parehas na form factor at footprint) — pagkakaiba sa Package, Propagation Delay, Operating Temperature Range, Output Type, Comparator Type.
LM2903M
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →LM2903D
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →LM2903N
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →LM2903M
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →LM2903BIDR
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →LM2903M/NOPB Mga Pinakamataas na Rating at Electrical Characteristics
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 channels |
| Channel Independence | 2 independent comparators |
| Type ng Output | Open collector |
| Maximum Input Offset Voltage | 2 mV |
| Input Current | 2 nA and 5 nA |
| Propagation Delay | 1.5 us |
| Supply Voltage Range | Up to 18 V |
| Single-Supply Operation | Supported |
| Split-Supply Operation | Supported |
| Common-Mode Operation | Includes a common-mode range to ground for single-supply operation |
| Hanay ng Temperature na Operasyon | -40°C to 85°C |
| Packhaging | SOIC (D), 8 pins |
| Uri ng Pagpapasok | Surface mount |
| Product Description | Low-offset, dual differential comparator |
Gabay sa Pin Configuration ng LM2903M/NOPB soic (d), 8 pins
Pin configuration para sa LM2903M/NOPB (soic (d), 8 pins package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.
Wala ng detalyadong pinout data na magagamit para sa LM2903M/NOPB.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
LM2903M/NOPB ay nararapat para sa 6 aplikasyons: Industrial Threshold Detection, Power-Supply Overvoltage Detection, Automotive Sensor Interface, Relay and Solenoid Control, Battery Voltage Monitoring, Instrumentation and Test Equipment.
Industrial Threshold Detection
The LM2903M/NOPB is suitable for comparing a sensor signal with an adjustable threshold in industrial monitoring equipment. Its maximum input offset voltage of 2 mV helps limit the switching boundary error, while the two independent channels allow one device to monitor two related conditions. Each comparator can drive an open-collector node with a pull-up resistor, providing a simple fail-safe digital event signal. The 1.5-microsecond listed propagation delay is adequate for temperature, level, or process-limit monitoring rather than high-speed timing. In implementation, place the divider and input traces away from motors and switching power nodes, reference both channels to a low-impedance ground plane, and select resistor values that account for input bias current as well as threshold tolerance.
Inirekomenda
Power-Supply Overvoltage Detection
The LM2903M/NOPB can monitor a divided power-supply rail and produce an open-collector fault signal when the voltage crosses a defined limit. The comparator supports supply operation extending to 18 V and includes a common-mode range to ground for single-supply configurations, making it relevant to industrial and automotive-style control circuits. Two channels can supervise positive and auxiliary rails independently. The external pull-up can be connected to the system logic supply, while the open-drain output provides wired fault signaling when suitable for the bus architecture. Designers should verify the exact common-mode limits and output sink current, use precision divider resistors, and prevent comparator input current from shifting the threshold significantly.
Inirekomenda
Automotive Sensor Interface
The LM2903M/NOPB can convert a sensor or diagnostic signal into a logic event when used within an automotive control module. Its -40°C to 85°C operating range and low-offset dual-comparator architecture suit threshold-based sensing, while the two channels provide independent monitoring functions in one 8-pin package. An open-collector output can be pulled up to the module's logic rail, simplifying interface with discrete logic or another open-collector device. The 1.5-microsecond propagation delay is suitable for slow vehicle signals, not high-speed sensor timing. For production use, confirm AEC-Q100 qualification for the selected orderable, protect input and output paths against automotive transients, and route sensitive comparator inputs away from ignition and motor-control switching nodes.
Inirekomenda
Relay and Solenoid Control
The LM2903M/NOPB can decide when to energize a relay, solenoid, or latching actuator by comparing a control voltage against a threshold. The open-collector output works naturally with an NPN driver transistor or other compatible interface stage, while the 2 mV maximum input offset supports relatively precise activation boundaries. Two comparator channels can monitor command and feedback conditions independently. Because the 1.5-microsecond response is much faster than most electromechanical actuator delays, it is adequate for normal switching. Include a suitable flyback diode for inductive loads, check the comparator's output sink rating, add hysteresis to prevent relay chatter, and keep high-current actuator return paths separate from the comparator ground reference.
Inirekomenda
Battery Voltage Monitoring
The LM2903M/NOPB is appropriate for monitoring a divided battery or portable-system voltage and generating an open-collector warning when the level crosses a threshold. Its low-power dual-comparator format permits two limits from one package, such as undervoltage and overvoltage indications, while the input common-mode capability near ground supports single-supply operation. The listed 1.5-microsecond propagation delay is negligible for battery monitoring. In portable equipment, the pull-up resistor should be selected to minimize standing current while maintaining an acceptable rise time at the input of the monitoring logic. Also account for comparator input bias current when selecting high-value dividers, protect the input against battery transients, and verify the complete operating-voltage range for the selected LM2903 orderable.
Inirekomenda
Instrumentation and Test Equipment
The LM2903M/NOPB can perform a basic limit decision in measurement and test equipment where a source, reference, or feedback voltage must be compared with an adjustable limit. Two independent channels reduce the number of comparator packages needed when testing upper and lower bounds. The maximum input offset voltage of 2 mV supports fine boundary selection, while open-collector outputs can drive rear-panel relay logic, status indicators, or a host interface through pull-ups. The 1.5-microsecond response is suitable for slow process-control and calibration functions but not precision waveform analysis. Use a low-noise reference, maintain a consistent ground reference across the analog and digital sections, and place input components close to the comparator to minimize noise pickup during precision measurements.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for LM2903M/NOPB — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | LM2903M | LM2903D | LM2903N | LM2903M | LM2903BIDR |
|---|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | onsemi | onsemi | Texas Instruments |
| Comparator Configuration | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator |
| Number of Independent Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Single-Supply Operation | Supported | Supported | Supported | Supported | Supported | Supported |
Pangunahing mga Pagkakaiba
- Low-offset threshold decision in two channels (kumpara saLM2903N)
- Open-collector interface suited to pull-up logic (kumpara saLM2903BIDR)
- Two independent comparisons in one 8-pin package (kumpara saLM2903D)
- Adequate speed for control and protection functions (kumpara saLM2903M)
Talaan ng Disenyo
Do not treat an open-collector output as a push-pull logic output. Add a pull-up resistor to the required positive logic rail, and size it from the receiver's input current, the comparator's sink-current limit, and the desired rising-edge time. If the node must drive a cable or long PCB trace, account for distributed capacitance because a large pull-up can produce a slow edge and a small pull-up can exceed the output sink rating.
Route the non-inverting and inverting inputs as a compact differential pair and keep them away from switching-node copper, inductors, high-current relay returns, and the open-collector output trace. Connect the comparator ground reference directly to the quiet analog-ground region. For stable threshold decisions, place the input divider and any hysteresis feedback components close to the device and use a low-impedance reference return.
Add deliberate hysteresis when the compared signals can cross slowly or contain noise; otherwise the comparator can repeatedly change state near the threshold. The listed 2 mV maximum input offset establishes a useful accuracy boundary but does not eliminate resistor tolerance, input-bias error, temperature drift, or noise. Evaluate those effects with the actual divider values and include them when setting the guaranteed switching threshold.
Place the device supply bypass capacitor close to the supply and ground pins, with a short and low-impedance return path. Decouple noisy loads rather than relying on the comparator's own supply pin to absorb their transients. If one package controls a relay and another channel monitors a sensitive reference, keep the relay-driver return current out of the comparator reference path to prevent ground bounce from shifting the decision point.
Impormasyon ng Pagsunod sa Kautusan
The manufacturer product page identifies the exact LM2903M/NOPB orderable as active, but the verified content does not explicitly state its RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.