LM2903M/NOPB - Dual Open-Collector Comparator | Texas Instruments
MPN: LM2903M/NOPB ✓ פעילLM2903M/NOPB סקירה
An analog comparator is a signal-conditioning semiconductor that compares two input voltages and changes its output state when one input exceeds the other. The LM2903 belongs to the comparator hierarchy within analog and mixed-signal semiconductors. A differential comparator can operate from a single supply or split supply, allowing it to compare signals near ground, bipolar signals, or thresholds referenced to a supply rail.
The LM2903M/NOPB provides two independent low-power, low-offset comparators in one package. Its open-collector outputs are designed for wired-interface use and require an external pull-up resistor to establish a positive logic high when the output transistor is off. The listed propagation delay is 1.5 microseconds, making the device suitable for threshold detection, level translation, relay or solenoid driving, and general industrial control functions where microsecond-scale decision speed is sufficient.
A broad supply range is useful in equipment operating from industrial or automotive-style voltage rails. The -40°C to 85°C temperature range supports industrial and extended-temperature environments, although the specific LM2903M/NOPB orderable status and quality qualification should be checked for each deployment. The 8-pin SOIC package is a standard surface-mount footprint that is larger than contemporary compact packages but remains convenient for hand assembly, prototyping, and through-hole-style external pull-up routing.
Typical uses include monitoring a sensor against an adjustable threshold, detecting overvoltage or undervoltage conditions, converting an analog level into a logic event, and providing two independent comparisons in control, instrumentation, or power-supply systems. Because the outputs are open collector, multiple devices or nodes can share a pull-up arrangement when the electrical conditions permit.
Designers should account for input common-mode range, output pull-up requirements, supply decoupling, and the effect of input bias current when selecting threshold resistors. Keep comparator inputs away from switching-node currents and provide a stable local ground reference. The open-collector nodes should have pull-up resistors selected for the required logic voltage, sink-current budget, rise-time target, and system power budget.
This page combines the manufacturer's ordering information, a source-grounded parameter summary, application engineering guidance, and package-level replacement analysis. It also identifies the design trade-offs that matter when comparing the LM2903M/NOPB with related dual comparators rather than relying only on basic device descriptions.
חלופות תחליף ישיר עבור LM2903M/NOPB — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם LM2903M/NOPB (אותו גורם צורה וטביעת רגל) — שונים ב Package, Propagation Delay, Operating Temperature Range, Output Type, Comparator Type.
LM2903M
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←LM2903D
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←LM2903N
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←LM2903M
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←LM2903BIDR
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←LM2903M/NOPB דירוגים מרביים ומאפיינים חשמליים
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 channels |
| Channel Independence | 2 independent comparators |
| סוג פלט | Open collector |
| Maximum Input Offset Voltage | 2 mV |
| Input Current | 2 nA and 5 nA |
| Propagation Delay | 1.5 us |
| Supply Voltage Range | Up to 18 V |
| Single-Supply Operation | Supported |
| Split-Supply Operation | Supported |
| Common-Mode Operation | Includes a common-mode range to ground for single-supply operation |
| טווח טמפרטורת פעולה | -40°C to 85°C |
| מארז | SOIC (D), 8 pins |
| סוג הרכבה | Surface mount |
| Product Description | Low-offset, dual differential comparator |
מדריך תצורת פינים של LM2903M/NOPB soic (d), 8 pins
תצורת פינים עבור LM2903M/NOPB (מארזת soic (d), 8 pins). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.
אין נתוני פריסת פינים מפורטים עבור LM2903M/NOPB.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
LM2903M/NOPB מתאים עבור 6 יישוםs: Industrial Threshold Detection, Power-Supply Overvoltage Detection, Automotive Sensor Interface, Relay and Solenoid Control, Battery Voltage Monitoring, Instrumentation and Test Equipment.
Industrial Threshold Detection
The LM2903M/NOPB is suitable for comparing a sensor signal with an adjustable threshold in industrial monitoring equipment. Its maximum input offset voltage of 2 mV helps limit the switching boundary error, while the two independent channels allow one device to monitor two related conditions. Each comparator can drive an open-collector node with a pull-up resistor, providing a simple fail-safe digital event signal. The 1.5-microsecond listed propagation delay is adequate for temperature, level, or process-limit monitoring rather than high-speed timing. In implementation, place the divider and input traces away from motors and switching power nodes, reference both channels to a low-impedance ground plane, and select resistor values that account for input bias current as well as threshold tolerance.
מומלץ
Power-Supply Overvoltage Detection
The LM2903M/NOPB can monitor a divided power-supply rail and produce an open-collector fault signal when the voltage crosses a defined limit. The comparator supports supply operation extending to 18 V and includes a common-mode range to ground for single-supply configurations, making it relevant to industrial and automotive-style control circuits. Two channels can supervise positive and auxiliary rails independently. The external pull-up can be connected to the system logic supply, while the open-drain output provides wired fault signaling when suitable for the bus architecture. Designers should verify the exact common-mode limits and output sink current, use precision divider resistors, and prevent comparator input current from shifting the threshold significantly.
מומלץ
Automotive Sensor Interface
The LM2903M/NOPB can convert a sensor or diagnostic signal into a logic event when used within an automotive control module. Its -40°C to 85°C operating range and low-offset dual-comparator architecture suit threshold-based sensing, while the two channels provide independent monitoring functions in one 8-pin package. An open-collector output can be pulled up to the module's logic rail, simplifying interface with discrete logic or another open-collector device. The 1.5-microsecond propagation delay is suitable for slow vehicle signals, not high-speed sensor timing. For production use, confirm AEC-Q100 qualification for the selected orderable, protect input and output paths against automotive transients, and route sensitive comparator inputs away from ignition and motor-control switching nodes.
מומלץ
Relay and Solenoid Control
The LM2903M/NOPB can decide when to energize a relay, solenoid, or latching actuator by comparing a control voltage against a threshold. The open-collector output works naturally with an NPN driver transistor or other compatible interface stage, while the 2 mV maximum input offset supports relatively precise activation boundaries. Two comparator channels can monitor command and feedback conditions independently. Because the 1.5-microsecond response is much faster than most electromechanical actuator delays, it is adequate for normal switching. Include a suitable flyback diode for inductive loads, check the comparator's output sink rating, add hysteresis to prevent relay chatter, and keep high-current actuator return paths separate from the comparator ground reference.
מומלץ
Battery Voltage Monitoring
The LM2903M/NOPB is appropriate for monitoring a divided battery or portable-system voltage and generating an open-collector warning when the level crosses a threshold. Its low-power dual-comparator format permits two limits from one package, such as undervoltage and overvoltage indications, while the input common-mode capability near ground supports single-supply operation. The listed 1.5-microsecond propagation delay is negligible for battery monitoring. In portable equipment, the pull-up resistor should be selected to minimize standing current while maintaining an acceptable rise time at the input of the monitoring logic. Also account for comparator input bias current when selecting high-value dividers, protect the input against battery transients, and verify the complete operating-voltage range for the selected LM2903 orderable.
מומלץ
Instrumentation and Test Equipment
The LM2903M/NOPB can perform a basic limit decision in measurement and test equipment where a source, reference, or feedback voltage must be compared with an adjustable limit. Two independent channels reduce the number of comparator packages needed when testing upper and lower bounds. The maximum input offset voltage of 2 mV supports fine boundary selection, while open-collector outputs can drive rear-panel relay logic, status indicators, or a host interface through pull-ups. The 1.5-microsecond response is suitable for slow process-control and calibration functions but not precision waveform analysis. Use a low-noise reference, maintain a consistent ground reference across the analog and digital sections, and place input components close to the comparator to minimize noise pickup during precision measurements.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור LM2903M/NOPB — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | LM2903M | LM2903D | LM2903N | LM2903M | LM2903BIDR |
|---|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | onsemi | onsemi | Texas Instruments |
| Comparator Configuration | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator |
| Number of Independent Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Single-Supply Operation | Supported | Supported | Supported | Supported | Supported | Supported |
מבדילים עיקריים
- Low-offset threshold decision in two channels (לעומתLM2903N)
- Open-collector interface suited to pull-up logic (לעומתLM2903BIDR)
- Two independent comparisons in one 8-pin package (לעומתLM2903D)
- Adequate speed for control and protection functions (לעומתLM2903M)
הערות תכנון
Do not treat an open-collector output as a push-pull logic output. Add a pull-up resistor to the required positive logic rail, and size it from the receiver's input current, the comparator's sink-current limit, and the desired rising-edge time. If the node must drive a cable or long PCB trace, account for distributed capacitance because a large pull-up can produce a slow edge and a small pull-up can exceed the output sink rating.
Route the non-inverting and inverting inputs as a compact differential pair and keep them away from switching-node copper, inductors, high-current relay returns, and the open-collector output trace. Connect the comparator ground reference directly to the quiet analog-ground region. For stable threshold decisions, place the input divider and any hysteresis feedback components close to the device and use a low-impedance reference return.
Add deliberate hysteresis when the compared signals can cross slowly or contain noise; otherwise the comparator can repeatedly change state near the threshold. The listed 2 mV maximum input offset establishes a useful accuracy boundary but does not eliminate resistor tolerance, input-bias error, temperature drift, or noise. Evaluate those effects with the actual divider values and include them when setting the guaranteed switching threshold.
Place the device supply bypass capacitor close to the supply and ground pins, with a short and low-impedance return path. Decouple noisy loads rather than relying on the comparator's own supply pin to absorb their transients. If one package controls a relay and another channel monitors a sensitive reference, keep the relay-driver return current out of the comparator reference path to prevent ground bounce from shifting the decision point.
מידע על תאימות
The manufacturer product page identifies the exact LM2903M/NOPB orderable as active, but the verified content does not explicitly state its RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.