LM2904LVIPWR - Dual 5.5V 1MHz Op Amp | Texas Instruments
MPN: LM2904LVIPWR ✓ NakahandaLM2904LVIPWR Ulas
An operational amplifier is an active analog component that amplifies the voltage difference between its non-inverting and inverting inputs. The LM2904LV belongs to the LM290xLV low-voltage operational-amplifier family, combining two amplifier channels in one package. This makes the device suitable for applications such as signal buffering, active filtering, differential amplification, instrumentation, and low-level analog conditioning.
The headline specifications are a 1 MHz gain-bandwidth product, a 3 mV offset voltage, and a 5.5 V maximum supply rating. These characteristics are useful for moderate-bandwidth, general-purpose analog designs where compactness and dual-channel functionality matter more than high-speed precision performance. The operating-temperature range of -40°C to +125°C supports use across industrial and extended-temperature equipment.
The LM2904LV uses conventional internal compensation and is configured as a dual operational amplifier. Its 1 MHz bandwidth supports general-purpose closed-loop signal work, while the two channels can implement independent amplifier functions or work together in differential, summing, and feedback configurations. Design calculations should use the manufacturer datasheet for gain-bandwidth behavior, output swing, input common-mode limits, and output-drive capability.
Typical uses include sensor-signal conditioning, audio preamplification, industrial control interfaces, low-frequency active filters, and general analog buffers. In dual-rail or single-supply systems, the circuit designer must verify the allowable input and output common-mode ranges against the actual supply voltage. Output loading and feedback-loop stability also require evaluation when driving capacitive or long external cables.
Use the manufacturer pin-description table when assigning PCB tracks and verify the exposed-pad requirements and recommended land pattern for the TSSOP package. Place input and feedback components close to the relevant amplifier pins, maintain short ground-return paths, and provide local supply bypassing to reduce noise and prevent feedback from unrelated circuitry.
This product page combines the key manufacturer specifications, ordering and package information, application guidance, and replacement-selection considerations in one engineering-focused reference. The comparison and design notes are intended to accelerate schematic selection, footprint verification, and first-board bring-up for dual low-voltage operational-amplifier designs.
Mga alternatibo na pwedeng ilagay na LM2904LVIPWR — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok LM2904LVIPWR (parehas na form factor at footprint) — pagkakaiba sa Amplifier Type, Gain-Bandwidth Product, Maximum Supply Voltage, Operating Temperature Range, Package Type.
LM2904VQPWR
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →LM2904LVIPWR Mga Pinakamataas na Rating at Electrical Characteristics
| Number of Channels | 2 channels |
| Amplifier Type | General-purpose operational amplifier |
| Maximum Supply Voltage | 5.5 V |
| Gain-Bandwidth Product | 1 MHz |
| Input Offset Voltage | 3 mV |
| Hanay ng Temperature na Operasyon | -40°C to +125°C |
| Package Type | TSSOP (PW) |
| Package Pin Count | 8 pins |
| Uri ng Pagpapasok | Surface mount |
| Tindminan RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
Gabay sa Pin Configuration ng LM2904LVIPWR 8 pins
Pin configuration para sa LM2904LVIPWR (8 pins package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.
Wala ng detalyadong pinout data na magagamit para sa LM2904LVIPWR.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
LM2904LVIPWR ay nararapat para sa 6 aplikasyons: Industrial Sensor Signal Conditioning, Audio Preamplification, Active Low-Pass Filters, Low-Frequency Data Acquisition, Battery-Powered Portable Instruments, Power Supply Control and Monitoring.
Industrial Sensor Signal Conditioning
The LM2904LVIPWR fits general-purpose industrial sensor conditioning because its dual configuration provides two amplifiers in one 8-pin TSSOP package, while the 1 MHz gain-bandwidth product supports signals well beyond basic DC scaling. A channel can provide gain followed by an active low-pass or differential stage, reducing board area when the source is a resistive bridge, potentiometer, or slow industrial transducer. Its -40°C to +125°C rating supports extended-temperature equipment. The designer should confirm the sensor’s excitation level, output common-mode voltage, required noise performance, and the amplifier’s input and output ranges before finalizing the circuit.
Inirekomenda
Audio Preamplification
The LM2904LVIPWR can be used for modest-bandwidth audio preamplification when the design operates from a supply no higher than 5.5 V and does not require rail-to-rail output swing. Its 1 MHz gain-bandwidth product provides more bandwidth than typical low-frequency audio paths generally require, while two channels can support stereo or a mono input plus an active filter. The 3 mV offset rating is noncritical for many audio stages but matters in quiet, high-gain designs. Confirm the input common-mode range, output swing, slew rate, and capacitive-load stability before choosing gain and filter resistors.
Inirekomenda
Active Low-Pass Filters
The LM2904LVIPWR is appropriate for first-order and moderate-order active filters operating within its 1 MHz bandwidth. Two independent channels can implement a two-pole filter using the familiar inverting topology, or the channels can form a buffered measurement chain. The device’s 3 mV input offset should be included in the output-error budget, while supply voltage determines the available signal range. Use stable resistor values, check each stage’s closed-loop gain against the gain-bandwidth limit, and verify that the intended operating frequency does not produce excessive phase error.
Inirekomenda
Low-Frequency Data Acquisition
The LM2904LVIPWR can condition low-bandwidth measurement signals in a compact data-acquisition front end. One channel may amplify a transducer output and the other may buffer a reference or provide additional gain. Its 1 MHz gain-bandwidth product is substantially higher than the bandwidth normally needed for slow sensors, while the -40°C to +125°C range supports industrial environments. The principal limits are the 3 mV offset, input bias behavior, common-mode range, and output swing. Confirm those parameters against the sensor output and ADC input range before using the device for high-resolution measurements.
Inirekomenda
Battery-Powered Portable Instruments
The LM2904LVIPWR is useful in battery-powered portable instruments when the signal chain operates at low voltage and the 5.5 V maximum supply rating provides adequate headroom. Its dual-channel TSSOP package reduces board footprint, while the 1 MHz bandwidth permits signal conditioning beyond DC and very-low-frequency requirements. Designers should verify current consumption for the complete operating mode, verify rail-to-rail behavior at the selected supply, and ensure the output does not exceed the downstream ADC or display input range. Local bypass capacitance and short analog routing are important for preserving low-noise operation in compact systems.
Inirekomenda
Power Supply Control and Monitoring
The LM2904LVIPWR can amplify and buffer low-level control or monitoring signals in a low-voltage power-management module. A channel may sense a scaled feedback node, compare it with a reference through external circuitry, or buffer an error signal to a controller. The 1 MHz bandwidth is adequate for many control loops operating well below that frequency, and the -40°C to +125°C rating supports industrial equipment. Verify the output swing at the selected supply, the offset contribution at high loop gain, and stability with the controller input capacitance before deployment.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for LM2904LVIPWR — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto |
|---|---|
| Package | 8-pin TSSOP (PW) |
| Brand | Texas Instruments |
| Number of Channels | 2 channels |
| Amplifier Type | General-purpose operational amplifier |
| Maximum Supply Voltage | 5.5 V |
| Gain-Bandwidth Product | 1 MHz |
| Input Offset Voltage | 3 mV |
| Operating Temperature Range | -40°C to +125°C |
| Package Pin Count | 8 pins |
| Mounting Type | Surface mount |
Pangunahing mga Pagkakaiba
- Dual-channel integration in an 8-pin TSSOP package (kumpara saSingle-channel operational amplifiers)
- Low-voltage family operation (kumpara saStandard 26 V LM2904)
- General-purpose bandwidth (kumpara saPrecision and high-speed amplifier families)
Talaan ng Disenyo
Place the supply bypass capacitor immediately adjacent to the LM2904LVIPWR power and ground pins, with the shortest practical connection to the device ground. Keep the two amplifier inputs, feedback components, and output routes away from switching nodes and high-current return paths. The PW package requires use of TI’s recommended land pattern and adequate solder-paste coverage at the fine-pitch leads.
Do not assume that the 5.5 V maximum supply rating means every input or output can reach the positive rail. Before finalizing a circuit, check the LM2904LV datasheet for input common-mode limits and output swing under the selected load. Also include the 3 mV input offset in precision calculations and verify stability when driving capacitive loads or driving long cables.
Use separate analog and digital return-current paths where practical, and join them according to the board’s ground strategy. Avoid routing the two channels through shared impedance when the channels carry substantially different currents or frequencies. Place feedback resistors close to their corresponding amplifier pins so parasitic capacitance does not alter the intended closed-loop response.
Size the analog supply for the operational-amplifier output current, local bypass network, and connected load rather than treating the 5.5 V rating as an output-current specification. Confirm output-drive and output-swing limits from the manufacturer datasheet. If the amplifier drives a load containing capacitance, verify stability and slew-rate requirements for the intended waveform.
Impormasyon ng Pagsunod sa Kautusan
The LM2904LV family product information identifies the device and package, but no specific environmental or material-compliance declarations are included here.