LM2904LVIPWR - Dual 5.5V 1MHz Op Amp | Texas Instruments
N.º da peça: LM2904LVIPWR ✓ AtivoLM2904LVIPWR Visão geral
An operational amplifier is an active analog component that amplifies the voltage difference between its non-inverting and inverting inputs. The LM2904LV belongs to the LM290xLV low-voltage operational-amplifier family, combining two amplifier channels in one package. This makes the device suitable for applications such as signal buffering, active filtering, differential amplification, instrumentation, and low-level analog conditioning.
The headline specifications are a 1 MHz gain-bandwidth product, a 3 mV offset voltage, and a 5.5 V maximum supply rating. These characteristics are useful for moderate-bandwidth, general-purpose analog designs where compactness and dual-channel functionality matter more than high-speed precision performance. The operating-temperature range of -40°C to +125°C supports use across industrial and extended-temperature equipment.
The LM2904LV uses conventional internal compensation and is configured as a dual operational amplifier. Its 1 MHz bandwidth supports general-purpose closed-loop signal work, while the two channels can implement independent amplifier functions or work together in differential, summing, and feedback configurations. Design calculations should use the manufacturer datasheet for gain-bandwidth behavior, output swing, input common-mode limits, and output-drive capability.
Typical uses include sensor-signal conditioning, audio preamplification, industrial control interfaces, low-frequency active filters, and general analog buffers. In dual-rail or single-supply systems, the circuit designer must verify the allowable input and output common-mode ranges against the actual supply voltage. Output loading and feedback-loop stability also require evaluation when driving capacitive or long external cables.
Use the manufacturer pin-description table when assigning PCB tracks and verify the exposed-pad requirements and recommended land pattern for the TSSOP package. Place input and feedback components close to the relevant amplifier pins, maintain short ground-return paths, and provide local supply bypassing to reduce noise and prevent feedback from unrelated circuitry.
This product page combines the key manufacturer specifications, ordering and package information, application guidance, and replacement-selection considerations in one engineering-focused reference. The comparison and design notes are intended to accelerate schematic selection, footprint verification, and first-board bring-up for dual low-voltage operational-amplifier designs.
Alternativas drop-in para LM2904LVIPWR — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com LM2904LVIPWR (mesmo formato e footprint) — diferindo em Amplifier Type, Gain-Bandwidth Product, Maximum Supply Voltage, Operating Temperature Range, Package Type.
LM2904VQPWR
✅ Drop-InConsulte o preço
Ver ficha técnica →LM2904LVIPWR Classificações máximas e características elétricas
| Number of Channels | 2 channels |
| Amplifier Type | General-purpose operational amplifier |
| Maximum Supply Voltage | 5.5 V |
| Gain-Bandwidth Product | 1 MHz |
| Input Offset Voltage | 3 mV |
| Faixa de temperatura de operação | -40°C to +125°C |
| Package Type | TSSOP (PW) |
| Package Pin Count | 8 pins |
| Tipo de montagem | Surface mount |
| Status RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
Guia de Configuração de Pinos do LM2904LVIPWR 8 pins
Configuração de pinos para LM2904LVIPWR (pacote 8 pins). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.
Nenhum dado detalhado de pinagem disponível para LM2904LVIPWR.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
LM2904LVIPWR é adequado para 6 aplicaçãos: Industrial Sensor Signal Conditioning, Audio Preamplification, Active Low-Pass Filters, Low-Frequency Data Acquisition, Battery-Powered Portable Instruments, Power Supply Control and Monitoring.
Industrial Sensor Signal Conditioning
The LM2904LVIPWR fits general-purpose industrial sensor conditioning because its dual configuration provides two amplifiers in one 8-pin TSSOP package, while the 1 MHz gain-bandwidth product supports signals well beyond basic DC scaling. A channel can provide gain followed by an active low-pass or differential stage, reducing board area when the source is a resistive bridge, potentiometer, or slow industrial transducer. Its -40°C to +125°C rating supports extended-temperature equipment. The designer should confirm the sensor’s excitation level, output common-mode voltage, required noise performance, and the amplifier’s input and output ranges before finalizing the circuit.
Recomendado
Audio Preamplification
The LM2904LVIPWR can be used for modest-bandwidth audio preamplification when the design operates from a supply no higher than 5.5 V and does not require rail-to-rail output swing. Its 1 MHz gain-bandwidth product provides more bandwidth than typical low-frequency audio paths generally require, while two channels can support stereo or a mono input plus an active filter. The 3 mV offset rating is noncritical for many audio stages but matters in quiet, high-gain designs. Confirm the input common-mode range, output swing, slew rate, and capacitive-load stability before choosing gain and filter resistors.
Recomendado
Active Low-Pass Filters
The LM2904LVIPWR is appropriate for first-order and moderate-order active filters operating within its 1 MHz bandwidth. Two independent channels can implement a two-pole filter using the familiar inverting topology, or the channels can form a buffered measurement chain. The device’s 3 mV input offset should be included in the output-error budget, while supply voltage determines the available signal range. Use stable resistor values, check each stage’s closed-loop gain against the gain-bandwidth limit, and verify that the intended operating frequency does not produce excessive phase error.
Recomendado
Low-Frequency Data Acquisition
The LM2904LVIPWR can condition low-bandwidth measurement signals in a compact data-acquisition front end. One channel may amplify a transducer output and the other may buffer a reference or provide additional gain. Its 1 MHz gain-bandwidth product is substantially higher than the bandwidth normally needed for slow sensors, while the -40°C to +125°C range supports industrial environments. The principal limits are the 3 mV offset, input bias behavior, common-mode range, and output swing. Confirm those parameters against the sensor output and ADC input range before using the device for high-resolution measurements.
Recomendado
Battery-Powered Portable Instruments
The LM2904LVIPWR is useful in battery-powered portable instruments when the signal chain operates at low voltage and the 5.5 V maximum supply rating provides adequate headroom. Its dual-channel TSSOP package reduces board footprint, while the 1 MHz bandwidth permits signal conditioning beyond DC and very-low-frequency requirements. Designers should verify current consumption for the complete operating mode, verify rail-to-rail behavior at the selected supply, and ensure the output does not exceed the downstream ADC or display input range. Local bypass capacitance and short analog routing are important for preserving low-noise operation in compact systems.
Recomendado
Power Supply Control and Monitoring
The LM2904LVIPWR can amplify and buffer low-level control or monitoring signals in a low-voltage power-management module. A channel may sense a scaled feedback node, compare it with a reference through external circuitry, or buffer an error signal to a controller. The 1 MHz bandwidth is adequate for many control loops operating well below that frequency, and the -40°C to +125°C rating supports industrial equipment. Verify the output swing at the selected supply, the offset contribution at high loop gain, and stability with the controller input capacitance before deployment.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para LM2904LVIPWR — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto |
|---|---|
| Package | 8-pin TSSOP (PW) |
| Brand | Texas Instruments |
| Number of Channels | 2 channels |
| Amplifier Type | General-purpose operational amplifier |
| Maximum Supply Voltage | 5.5 V |
| Gain-Bandwidth Product | 1 MHz |
| Input Offset Voltage | 3 mV |
| Operating Temperature Range | -40°C to +125°C |
| Package Pin Count | 8 pins |
| Mounting Type | Surface mount |
Principais diferenciais
- Dual-channel integration in an 8-pin TSSOP package (vs Single-channel operational amplifiers)
- Low-voltage family operation (vs Standard 26 V LM2904)
- General-purpose bandwidth (vs Precision and high-speed amplifier families)
Notas de projeto
Place the supply bypass capacitor immediately adjacent to the LM2904LVIPWR power and ground pins, with the shortest practical connection to the device ground. Keep the two amplifier inputs, feedback components, and output routes away from switching nodes and high-current return paths. The PW package requires use of TI’s recommended land pattern and adequate solder-paste coverage at the fine-pitch leads.
Do not assume that the 5.5 V maximum supply rating means every input or output can reach the positive rail. Before finalizing a circuit, check the LM2904LV datasheet for input common-mode limits and output swing under the selected load. Also include the 3 mV input offset in precision calculations and verify stability when driving capacitive loads or driving long cables.
Use separate analog and digital return-current paths where practical, and join them according to the board’s ground strategy. Avoid routing the two channels through shared impedance when the channels carry substantially different currents or frequencies. Place feedback resistors close to their corresponding amplifier pins so parasitic capacitance does not alter the intended closed-loop response.
Size the analog supply for the operational-amplifier output current, local bypass network, and connected load rather than treating the 5.5 V rating as an output-current specification. Confirm output-drive and output-swing limits from the manufacturer datasheet. If the amplifier drives a load containing capacitance, verify stability and slew-rate requirements for the intended waveform.
Informações de conformidade
The LM2904LV family product information identifies the device and package, but no specific environmental or material-compliance declarations are included here.