LM324M/NOPB - Quad 32V 1MHz Op Amp | Texas Instruments
MPN: LM324M/NOPB ✓ NakahandaLM324M/NOPB Ulas
An operational amplifier, or op amp, is a voltage-controlled differential amplifier whose high open-loop gain enables closed-loop functions such as buffering, amplification, summing, comparison, filtering, and differential signal conversion. The LM324 belongs to the broader operational-amplifier hierarchy within analog and mixed-signal semiconductors. Its four-amplifier configuration reduces package count and board area when several independent amplifier stages are required in the same circuit.
The LM324M/NOPB is identified by Texas Instruments as a low-power quad operational amplifier. Its four amplifier circuits provide a 1 MHz gain-bandwidth product, while the 32 V supply rating supports higher-voltage industrial and instrumentation systems than typical low-voltage rail-to-rail amplifiers. The 14-pin SOIC (D) package is a conventional surface-mount package, and the specified 0 °C to 70 °C temperature range targets commercial operating conditions.
The LM324 family is designed to operate from either a single supply or split supplies. Internal frequency compensation allows stable operation in common noninverting, inverting, voltage-follower, summing, and amplifier configurations without an external compensation network. Its general-purpose architecture is appropriate for transducer amplifiers, DC gain blocks, sensors, audio circuitry, and conventional control loops where moderate bandwidth and broad supply flexibility are more important than rail-to-rail input or output operation.
Typical applications include four-channel sensor conditioning, low-frequency active filters, audio preamplifier stages, current-loop interfaces, instrumentation buffers, and general-purpose analog boards. Because all four channels share one package, decoupling requirements and ground-return design should be evaluated for the complete circuit rather than for each amplifier independently.
When laying out a board, place power and ground connections to minimize loop area and avoid routing sensitive input traces close to high-current outputs. The SOIC footprint leaves more separation between pins than a compact leadless package, which can simplify prototype assembly, inspection, and rework. Confirm the exact circuit limits, output-swing behavior, input common-mode range, and stability requirements against the manufacturer datasheet for the intended supply voltage and load.
This product record combines the manufacturer’s 32 V, 1 MHz, 14-SOIC and 0 °C to 70 °C identification with same-package alternatives, application guidance, design notes, and a parameter-oriented comparison for engineers evaluating quad general-purpose op amps in SOIC-14 designs.
Mga alternatibo na pwedeng ilagay na LM324M/NOPB — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok LM324M/NOPB (parehas na form factor at footprint) — pagkakaiba sa Amplifier Type, Operating Temperature Range, Compensation, Package, Package Type.
LM324MX/NOPB
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →LM324AM/NOPB
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →LM324AMX/NOPB
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →LM324DT
✅ Drop-In✗ Wala sa Stock
$0.0827 / Yunit
Tingnan ang Datasheet →LM324M
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →LM324M/NOPB Mga Pinakamataas na Rating at Electrical Characteristics
| Product Type | Quad operational amplifier |
| Amplifier Circuit Count | 4 circuits |
| Product Classification | Standard general-purpose amplifier |
| Maximum Supply Voltage | 32 V |
| Gain-Bandwidth Product | 1 MHz |
| Supply Configuration | Single or split supply |
| Hanay ng Temperature na Operasyon | 0 °C to 70 °C |
| Package Type | SOIC (D) |
| Bilang ng Pin | 14 pins |
| Uri ng Pagpapasok | Surface mount |
| Frequency Compensation | Internally compensated |
| Power Class | Low power |
| Channel Architecture | Four independent amplifiers |
Gabay sa Pin Configuration ng LM324M/NOPB soic (d)
Pin configuration para sa LM324M/NOPB (soic (d) package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.
Wala ng detalyadong pinout data na magagamit para sa LM324M/NOPB.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
LM324M/NOPB ay nararapat para sa 6 aplikasyons: Industrial Sensor Signal Conditioning, Audio Preamplifier Stages, Active Filters and Control Loops, Data Acquisition Buffering, Power Supply Current Monitoring, IoT Sensor Interface Board.
Industrial Sensor Signal Conditioning
The LM324M/NOPB is well suited to conditioning four low-frequency sensor signals in a 14-pin SOIC package. Its four internally compensated amplifier channels can implement non-inverting, inverting, differential, or buffering stages without adding external compensation components. The 32 V maximum supply rating provides more headroom than low-voltage rail-to-rail devices, while the 1 MHz gain-bandwidth product is appropriate for sensors such as temperature, pressure, and resistive bridges. Design the input network so each signal remains inside the amplifier’s common-mode range, and check offset and bias current against the measurement accuracy before fixing the gain.
Inirekomenda
Audio Preamplifier Stages
The LM324M/NOPB can implement four low-frequency audio preamplifier or mixing stages because each internally compensated channel provides approximately 1 MHz gain-bandwidth product. Its 32 V maximum supply rating is useful for higher-voltage analog systems, while the general-purpose architecture suits microphone, line-level, and active-filter blocks that do not require rail-to-rail swing. Keep the gain structure compatible with the 1 MHz bandwidth class and observe the output-swing and loading limits from the manufacturer datasheet. Decoupling should be placed close to the package to prevent power-supply noise from entering all four amplified channels simultaneously.
Inirekomenda
Active Filters and Control Loops
The LM324M/NOPB provides four channels for low-frequency active filters, integrators, PID-style control loops, and error amplifiers. The 1 MHz gain-bandwidth product supports applications well below megahertz signal rates, while internal frequency compensation simplifies conventional closed-loop design. The 32 V class supply rating accommodates industrial control rails, and the four-channel package reduces component count. Select resistor and capacitor values around the desired closed-loop bandwidth and noise corner, and verify stability at the actual load capacitance and output-current conditions before releasing the design.
Inirekomenda
Data Acquisition Buffering
The LM324M/NOPB is useful for buffering multiple inputs toward an analog-to-digital converter or measurement front end when modest bandwidth is sufficient. Four buffered channels can isolate source impedances, scale bipolar signals, or implement simple differential-to-single-ended conversion. Its 1 MHz gain-bandwidth product is normally ample for slow sensor or control signals, and the 32 V maximum supply class is useful where the acquisition section operates above low-voltage logic rails. Check common-mode limits, input offset, output swing, and capacitive loading, because source impedance and ADC sample timing can otherwise affect accuracy.
Inirekomenda
Power Supply Current Monitoring
The LM324M/NOPB can form low-side current-monitoring, voltage-amplification, or thresholding circuits in a 32 V class supply environment. Its general-purpose amplifiers can be combined as a difference stage, current-to-voltage buffer, or gain amplifier around a shunt or sensor. The 1 MHz class bandwidth is sufficient for many power-control feedback paths, while four channels allow monitoring, filtering, and auxiliary functions to share one package. Ensure the shunt and amplifier input remain within the common-mode range, and use the package’s ground and supply pins to prevent measurement error from shared return-current drops.
Inirekomenda
IoT Sensor Interface Board
The LM324M/NOPB fits a compact IoT sensor interface where several low-bandwidth analog channels must be conditioned before digital conversion. A single 14-pin SOIC can provide four gain or buffer stages, reducing board area compared with separate single amplifiers. Its 32 V maximum supply rating broadens compatibility with industrial sensor inputs, and the 1 MHz bandwidth class is suitable for slow environmental and status signals rather than high-speed communications. Keep sensitive sensor traces short and isolated from switching supplies, and account for the amplifier’s input offset, bias current, and common-mode behavior when setting the measurement resolution.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for LM324M/NOPB — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | LM324MX/NOPB | LM324AM/NOPB | LM324AMX/NOPB | LM324DT | LM324M |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | SOIC-14 | SOIC-14 | SOIC-14 | SOIC-14 | SOIC-14 | SOIC-14 |
| Amplifier Circuit Count | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Maximum Supply Voltage | 32 V | 32 V class | 32 V class | 32 V class | 32 V class | 32 V class |
| Gain-Bandwidth Product | 1 MHz | 1 MHz class | 1 MHz class | 1 MHz class | 1 MHz class | 1 MHz class |
| Supply Configuration | Single or split supply | Single or split supply | Single or split supply | Single or split supply | Single or split supply | Single or split supply |
| Compensation | Internally frequency compensated | Internally frequency compensated | Internally frequency compensated | Internally frequency compensated | Internally frequency compensated | Internally frequency compensated |
| Power Class | Low power | Low power | Low power | Low power | Low power | Low power |
| Primary Function | General-purpose amplifier | General-purpose amplifier | General-purpose amplifier | General-purpose amplifier | General-purpose amplifier | General-purpose amplifier |
Pangunahing mga Pagkakaiba
- Four amplifiers are consolidated in one 14-pin SOIC (kumpara saLM324DT)
- Broad supply capability for general-purpose analog systems (kumpara saLM324AM/NOPB)
- Single-supply and split-supply operating flexibility (kumpara saLM324MX/NOPB)
- Multi-amplifier consolidation reduces board-level part count (kumpara saLM324M)
Talaan ng Disenyo
Place the required supply-bypass capacitors immediately adjacent to the LM324M/NOPB power and ground pins, and use the shortest practical connection between each capacitor and the package. Because all four amplifiers share the same supply pins, verify that the common trace and exposed board copper can carry the aggregate channel current without producing excessive voltage drop or ground bounce. Sensitive noninverting-input traces should run away from output and supply-current paths.
Do not assume that a nominal 32 V maximum supply rating makes every operating point valid. Check the datasheet limits for total supply voltage, input common-mode range, output swing, input common-mode differential limits, and output-current behavior at the selected supply. Single-supply operation also means the usable input and output range remains constrained even though the four channels can share one package.
Keep each noninverting input close to its source and provide a local return path for input bias current. Where a high-impedance sensor drives the amplifier, stray capacitance can change frequency response, and output loading can cause unexpected gain or stability behavior. Check closed-loop bandwidth using the selected feedback network and verify output stability with the actual cable, sensor, or downstream input capacitance before production.
Estimated: using the manufacturer-identified maximum supply rating of 32 V, a 5 V output, and a 20 mA load gives approximate regulator dissipation of (32 V - 5 V) × 0.020 A = 0.54 W. Actual dissipation is lower when the operating supply is closer to 5 V. Use the actual minimum input, output, load, and ambient temperature to evaluate SOIC copper dissipation and any required thermal margin.
Impormasyon ng Pagsunod sa Kautusan
The 0 °C to 70 °C commercial temperature range and general-purpose amplifier classification do not establish AEC-Q100 qualification. Compliance status requires confirmation from the manufacturer’s current product documentation.