LT1920IS8 - Precision Instrumentation Amplifier | Analog Devices
MPN: LT1920IS8 ✓ NakahandaLT1920IS8 Ulas
An instrumentation amplifier is a specialized amplifier that measures the voltage difference between two input signals while rejecting common-mode voltage and interference. The LT1920 belongs to the instrumentation amplifier hierarchy within analog signal-chain ICs and combines a differential input stage, high-gain error amplifier, and output stage in one package. This integration reduces external component count compared with a discrete three-op-amp implementation while preserving gain accuracy over a wide range.
The LT1920 requires only one external resistor to establish gains from 1 to 10,000. Analog Devices specifies a gain accuracy of 30 ppm, supporting precise gain control in strain-gauge, bridge, and biomedical measurement systems. Its 7.5 nV/√Hz voltage noise at 1 kHz is maintained with typical power dissipation corresponding to 0.9 mA current. The dual-supply operating range of ±2.3 V to ±15 V also supports both low-voltage portable equipment and higher-voltage industrial instrumentation.
Input fault protection can be improved by placing an external 5 kΩ resistor in series with each input. Analog Devices states that this arrangement accepts DC input fault voltages up to ±100 V and raises ESD immunity to 8 kV contact and 15 kV air discharge. With two external 5 kΩ resistors, the LT1920 passes the IEC 1000-4-2 level 4 specification. This protection capability makes the amplifier useful where sensor inputs may be exposed to accidental overvoltage during field wiring or maintenance.
Typical applications include bridge-amplifier front ends, pressure and load-cell signal conditioning, battery-powered instrumentation, medical monitoring equipment, and precision current sensing. In a strain-gauge bridge, the small differential output can be amplified without the common-mode signal overwhelming the measurement. In portable equipment, the 0.9 mA typical supply current helps limit power consumption while retaining low input noise.
Design the gain resistor for the required differential gain and keep input and output layouts compact to minimize parasitic capacitance and noise pickup. Confirm the supply voltage, input common-mode range, output swing, and protection-resistor arrangement for the operating environment. The external series resistors are especially important when the source can present fault voltages above the amplifier input rating.
This page combines the manufacturer’s core LT1920 specifications with package details, protected-input design guidance, practical application patterns, and a compatibility-focused comparison. These engineering details help designers assess the LT1920IS8 for precision differential measurement, establish protection requirements, and determine whether a direct replacement satisfies both mechanical and electrical constraints.
Mga alternatibo na pwedeng ilagay na LT1920IS8 — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok LT1920IS8 (parehas na form factor at footprint) — pagkakaiba sa Number of Circuits, Package, Supply Voltage Range.
LT1920CS8
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
LT1920IS8#PBF
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
AD620ARZ
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →LT1920IS8 Mga Pinakamataas na Rating at Electrical Characteristics
| Device Type | Single-resistor gain-programmable precision instrumentation amplifier |
| Number of Circuits | 1 circuit |
| Gain Range | 1 to 10,000 |
| Gain Accuracy | 30 ppm |
| Input Voltage Noise | 7.5 nV/√Hz at 1 kHz |
| Typical Supply Current | 0.9 mA |
| Supply Voltage Range | ±2.3 V to ±15 V |
| Minimum Total Supply Voltage | 4.6 V |
| Maximum Total Supply Voltage | 30 V |
| Protected DC Input Fault Voltage | Up to ±100 V with external 5 kΩ input resistors |
| ESD Immunity | 8 kV contact and 15 kV air discharge with external 5 kΩ input resistors |
| ESD Standard | IEC 1000-4-2 level 4 |
| Packhaging | 8-pin SO |
| Package Pin Count | 8 pins |
| Uri ng Pagpapasok | Surface mount |
| Temperature Grade | Industrial |
Gabay sa Pin Configuration ng LT1920IS8 8 pins
Pin configuration para sa LT1920IS8 (8 pins package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.
Wala ng detalyadong pinout data na magagamit para sa LT1920IS8.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
LT1920IS8 ay nararapat para sa 6 aplikasyons: Strain-Gauge Bridge Amplification, Precision Load-Cell Measurement, Medical Signal Conditioning, Battery-Powered Sensor Interface, Industrial Current Sensing, Protected Field-Sensor Front End.
Strain-Gauge Bridge Amplification
The LT1920IS8 suits strain-gauge bridges because it amplifies the small differential bridge output while rejecting the larger common-mode voltage. Its specified gain accuracy of 30 ppm and input noise of 7.5 nV/√Hz at 1 kHz help preserve weak mechanical measurements. The 8-pin SO package keeps the analog front end compact, while the ±2.3 V to ±15 V supply range accommodates both low-voltage portable systems and higher-voltage laboratory instrumentation. Confirm the bridge excitation level, output range, and gain resistor before deployment.
Precision Load-Cell Measurement
The LT1920IS8 provides the differential input and adjustable gain required for load-cell signal conditioning. A gain of 1 to 10,000 allows the same amplifier architecture to cover different transducer sensitivities and excitation voltages. Its 7.5 nV/√Hz noise at 1 kHz is valuable when the load-cell output is small, while the 0.9 mA typical supply current supports compact weighing and portable force-measurement equipment. Validate input common-mode range and output swing for the selected bridge resistance and excitation.
Medical Signal Conditioning
The LT1920IS8 is applicable to low-level medical sensor front ends where a differential signal must be amplified before conversion or isolation. Its 7.5 nV/√Hz input noise at 1 kHz reduces the amplifier contribution to the measurement floor, and single-resistor gain programming simplifies control circuitry. The device’s protected-input configuration can accept DC fault voltages up to ±100 V with external 5 kΩ resistors and meets IEC 1000-4-2 level 4 under the stated conditions. Final medical-system validation must consider applicable safety, isolation, and signal-integrity requirements.
Battery-Powered Sensor Interface
The LT1920IS8 fits battery-powered sensor interfaces because it combines low input noise with a typical supply current of 0.9 mA. Its minimum total supply of 4.6 V allows operation from regulated 5 V rails, while the ±15 V maximum supports higher-voltage industrial systems. With a 1 to 10,000 gain range, one compact 8-pin SO device can amplify pressure, temperature, or current-sense signals. Select the gain resistor and bypass capacitors to control power consumption and maintain accuracy across the battery’s discharge range.
Industrial Current Sensing
The LT1920IS8 can amplify the small differential voltage produced by a low-side or isolated current-sense element. The precision gain range of 1 to 10,000 supports adjustment from millivolt-level sensor outputs to higher full-scale voltages, and the 30 ppm gain accuracy helps reduce calibration error. Its low 7.5 nV/√Hz input noise helps preserve measurement resolution, while protected inputs are useful when wiring may be exposed to accidental voltage events. Confirm shunt common-mode voltage, Kelvin routing, and amplifier output limits.
Protected Field-Sensor Front End
The LT1920IS8 is useful in field-wired instrumentation where input cables can introduce ESD events or accidental DC faults. Analog Devices specifies that external 5 kΩ series resistors permit DC input fault voltages up to ±100 V and provide 8 kV contact or 15 kV air-discharge ESD immunity. The protection circuit does not replace normal overvoltage analysis, so verify resistor power dissipation and signal bandwidth. The 8-pin SO package allows the amplifier and protection components to be placed close to a compact sensor terminal board.
Impormasyon ng Talumpati sa Engineering for LT1920IS8 — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | LT1920CS8 | LT1920IS8#PBF | AD620 |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-pin SO | 8-pin SO | 8-pin SO | 8-pin SO |
| Circuit Count | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Gain Programming | One external resistor | One external resistor | One external resistor | External resistor gain network |
Pangunahing mga Pagkakaiba
- Single-resistor gain programming (kumpara saAD620)
- Low-noise operation at low supply current (kumpara saAD620)
- Documented protected-input operation (kumpara saAD620)
Talaan ng Disenyo
Do not treat package compatibility as proof that the gain-setting network is interchangeable. The LT1920 uses one external resistor for gains from 1 to 10,000, while the AD620 uses a different resistor arrangement. Before substituting AD620 for LT1920IS8, recalculate the gain resistor, confirm the feedback and reference-pin behavior, and compare the input common-mode range and output swing. The Analog Devices product page identifies the LT1920 as an improved AD620 replacement, but circuit-level verification remains essential.
Route the differential input pair as a short, tightly coupled pair and connect the gain resistor close to the corresponding LT1920IS8 pin. Avoid routing these nodes beneath switching-regulator inductors, relay contacts, or digital return paths. Place input protection resistors ahead of the amplifier and preserve a low-impedance return for each source. These layout practices reduce conversion of common-mode interference into differential error and help the 7.5 nV/√Hz input-noise figure remain meaningful in the assembled circuit.
For field-wired inputs, use the Analog Devices protection configuration of one 5 kΩ series resistor at each input. This arrangement supports DC fault voltages up to ±100 V and provides 8 kV contact or 15 kV air-discharge ESD immunity, including IEC 1000-4-2 level 4 compliance as stated by the manufacturer. Check resistor power dissipation under the maximum sustained fault condition and add further attenuation if the sensor source can exceed the stated ±100 V limit.
Confirm the source can operate from a minimum total supply of 4.6 V and that the selected output level remains inside the output-swing limits at the required load current. The LT1920IS8 draws a typical 0.9 mA, making it suitable for low-power instrumentation, but total system demand includes protection resistors, sensor excitation, and external circuitry. Use local bypass capacitors close to the supply pins and verify settling behavior over the full measurement bandwidth rather than relying only on quiescent-current figures.
Impormasyon ng Pagsunod sa Kautusan
Analog Devices specifies IEC 1000-4-2 level 4 ESD immunity when two external 5 kΩ input resistors are used. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not established by the cited product information.