Analog Devices

LT1920IS8 - Precision Instrumentation Amplifier | Analog Devices

MPN: LT1920IS8 ✓ Aktif
7.5 nV/√Hz at 1 kHz Vdss 0.9 mA Id 8-pin SO Package
MOQ: 1 |

LT1920IS8 Ringkasan

The Analog Devices LT1920IS8 is a low-power, precision instrumentation amplifier with a gain range of 1 to 10,000, input voltage noise of 7.5 nV/√Hz at 1 kHz, and typical supply current of 0.9 mA. The device is offered in an 8-pin SO package and operates from ±2.3 V to ±15 V supplies. Its single-resistor gain programming makes it suitable for compact sensor and measurement circuits requiring accurate differential amplification.

An instrumentation amplifier is a specialized amplifier that measures the voltage difference between two input signals while rejecting common-mode voltage and interference. The LT1920 belongs to the instrumentation amplifier hierarchy within analog signal-chain ICs and combines a differential input stage, high-gain error amplifier, and output stage in one package. This integration reduces external component count compared with a discrete three-op-amp implementation while preserving gain accuracy over a wide range.

The LT1920 requires only one external resistor to establish gains from 1 to 10,000. Analog Devices specifies a gain accuracy of 30 ppm, supporting precise gain control in strain-gauge, bridge, and biomedical measurement systems. Its 7.5 nV/√Hz voltage noise at 1 kHz is maintained with typical power dissipation corresponding to 0.9 mA current. The dual-supply operating range of ±2.3 V to ±15 V also supports both low-voltage portable equipment and higher-voltage industrial instrumentation.

Input fault protection can be improved by placing an external 5 kΩ resistor in series with each input. Analog Devices states that this arrangement accepts DC input fault voltages up to ±100 V and raises ESD immunity to 8 kV contact and 15 kV air discharge. With two external 5 kΩ resistors, the LT1920 passes the IEC 1000-4-2 level 4 specification. This protection capability makes the amplifier useful where sensor inputs may be exposed to accidental overvoltage during field wiring or maintenance.

Typical applications include bridge-amplifier front ends, pressure and load-cell signal conditioning, battery-powered instrumentation, medical monitoring equipment, and precision current sensing. In a strain-gauge bridge, the small differential output can be amplified without the common-mode signal overwhelming the measurement. In portable equipment, the 0.9 mA typical supply current helps limit power consumption while retaining low input noise.

Design the gain resistor for the required differential gain and keep input and output layouts compact to minimize parasitic capacitance and noise pickup. Confirm the supply voltage, input common-mode range, output swing, and protection-resistor arrangement for the operating environment. The external series resistors are especially important when the source can present fault voltages above the amplifier input rating.

This page combines the manufacturer’s core LT1920 specifications with package details, protected-input design guidance, practical application patterns, and a compatibility-focused comparison. These engineering details help designers assess the LT1920IS8 for precision differential measurement, establish protection requirements, and determine whether a direct replacement satisfies both mechanical and electrical constraints.

Pilihan pengganti yang segera untuk LT1920IS8 — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.

Varietas dalam siri ini

Model serupa yang kompatibel dengan pengganti yang segera LT1920IS8 (sama faktor bentuk dan kaki) — berbeza dalam Number of Circuits, Package, Supply Voltage Range.

Analog Devices
Number of Circuits: 1
Package: 8-SOIC (0.154", 3.90mm Width)
Supply Voltage Range: ±2.3 V to ±18 V
Bandingkan Dengan LT1920IS8 →

LT1920CS8

✅ Masuk Drop-In
📦 8-pin SO
Same 8-pin SO construction and 1 to 10,000 gain capability; temperature-grade designation differs, with 0% stated change to the listed gain range

📋 Alternatif rujukan (tidak dalam katalog)

LT1920IS8#PBF

✅ Masuk Drop-In
📦 8-pin SO
Lead-free ordering designation for the same LT1920IS8 electrical configuration; 0% stated change to the listed gain, noise, or supply specifications

📋 Alternatif rujukan (tidak dalam katalog)

AD620ARZ

✅ Masuk Drop-In
Analog Devices
📦 8-pin SO
Instrumentation Amplifier · 1 · 1 to 10,000 · ±2.3 V to ±18 V · 1.3 mA · 100 dB · 50 µV · 1.0 nA

Hubungi untuk harga

Lihat Datasheet →

LT1920IS8 Penilaian maksimum & Ciri-ciri Elektrik

Device Type Single-resistor gain-programmable precision instrumentation amplifier
Number of Circuits 1 circuit
Gain Range 1 to 10,000
Gain Accuracy 30 ppm
Input Voltage Noise 7.5 nV/√Hz at 1 kHz
Typical Supply Current 0.9 mA
Supply Voltage Range ±2.3 V to ±15 V
Minimum Total Supply Voltage 4.6 V
Maximum Total Supply Voltage 30 V
Protected DC Input Fault Voltage Up to ±100 V with external 5 kΩ input resistors
ESD Immunity 8 kV contact and 15 kV air discharge with external 5 kΩ input resistors
ESD Standard IEC 1000-4-2 level 4
Kemasan 8-pin SO
Package Pin Count 8 pins
Jenis Pemasangan Surface mount
Temperature Grade Industrial

Panduan Konfigurasi Pin LT1920IS8 8 pins

Konfigurasi pin untuk LT1920IS8 (8 pins pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.

Garis bentuk pengecah pakai 8 pins untuk LT1920IS8

Tiada data garisan pin yang diperoleh untuk LT1920IS8.

Rujuk kepada lembaran data untuk konfigurasi pin penuh.

Aplikasi Biasa

LT1920IS8 patut untuk 6 aplikasis: Strain-Gauge Bridge Amplification, Precision Load-Cell Measurement, Medical Signal Conditioning, Battery-Powered Sensor Interface, Industrial Current Sensing, Protected Field-Sensor Front End.

🏭

Strain-Gauge Bridge Amplification

The LT1920IS8 suits strain-gauge bridges because it amplifies the small differential bridge output while rejecting the larger common-mode voltage. Its specified gain accuracy of 30 ppm and input noise of 7.5 nV/√Hz at 1 kHz help preserve weak mechanical measurements. The 8-pin SO package keeps the analog front end compact, while the ±2.3 V to ±15 V supply range accommodates both low-voltage portable systems and higher-voltage laboratory instrumentation. Confirm the bridge excitation level, output range, and gain resistor before deployment.

⚖️

Precision Load-Cell Measurement

The LT1920IS8 provides the differential input and adjustable gain required for load-cell signal conditioning. A gain of 1 to 10,000 allows the same amplifier architecture to cover different transducer sensitivities and excitation voltages. Its 7.5 nV/√Hz noise at 1 kHz is valuable when the load-cell output is small, while the 0.9 mA typical supply current supports compact weighing and portable force-measurement equipment. Validate input common-mode range and output swing for the selected bridge resistance and excitation.

💊

Medical Signal Conditioning

The LT1920IS8 is applicable to low-level medical sensor front ends where a differential signal must be amplified before conversion or isolation. Its 7.5 nV/√Hz input noise at 1 kHz reduces the amplifier contribution to the measurement floor, and single-resistor gain programming simplifies control circuitry. The device’s protected-input configuration can accept DC fault voltages up to ±100 V with external 5 kΩ resistors and meets IEC 1000-4-2 level 4 under the stated conditions. Final medical-system validation must consider applicable safety, isolation, and signal-integrity requirements.

🔋

Battery-Powered Sensor Interface

The LT1920IS8 fits battery-powered sensor interfaces because it combines low input noise with a typical supply current of 0.9 mA. Its minimum total supply of 4.6 V allows operation from regulated 5 V rails, while the ±15 V maximum supports higher-voltage industrial systems. With a 1 to 10,000 gain range, one compact 8-pin SO device can amplify pressure, temperature, or current-sense signals. Select the gain resistor and bypass capacitors to control power consumption and maintain accuracy across the battery’s discharge range.

🔧

Industrial Current Sensing

The LT1920IS8 can amplify the small differential voltage produced by a low-side or isolated current-sense element. The precision gain range of 1 to 10,000 supports adjustment from millivolt-level sensor outputs to higher full-scale voltages, and the 30 ppm gain accuracy helps reduce calibration error. Its low 7.5 nV/√Hz input noise helps preserve measurement resolution, while protected inputs are useful when wiring may be exposed to accidental voltage events. Confirm shunt common-mode voltage, Kelvin routing, and amplifier output limits.

🧩

Protected Field-Sensor Front End

The LT1920IS8 is useful in field-wired instrumentation where input cables can introduce ESD events or accidental DC faults. Analog Devices specifies that external 5 kΩ series resistors permit DC input fault voltages up to ±100 V and provide 8 kV contact or 15 kV air-discharge ESD immunity. The protection circuit does not replace normal overvoltage analysis, so verify resistor power dissipation and signal bandwidth. The 8-pin SO package allows the amplifier and protection components to be placed close to a compact sensor terminal board.

What are the key specifications of LT1920IS8?
The LT1920IS8 is a precision instrumentation amplifier with programmable gain from 1 to 10,000, input noise of 7.5 nV/√Hz at 1 kHz, and typical supply current of 0.9 mA. According to the Analog Devices LT1920 datasheet, it operates from ±2.3 V to ±15 V and is offered in an 8-pin SO package. A single external resistor sets the gain, simplifying precision bridge, current-sense, and sensor-interface designs while preserving 30 ppm gain accuracy.
Where can I download the LT1920IS8 datasheet PDF?
The official Analog Devices LT1920 datasheet PDF is available from the manufacturer link listed on this page. It describes the 8-pin SO and PDIP options, the 1 to 10,000 gain range, 7.5 nV/√Hz input noise, external resistor gain-setting network, supply limits, and protected-input configuration. Use the manufacturer document for final pin assignments, recommended application circuits, electrical characteristics, and operating-limit checks before completing the PCB design.
Where can I find the LT1920IS8 pinout?
The LT1920IS8 pinout is shown in the Analog Devices LT1920 datasheet, which describes the device in an 8-pin SO package. Use the manufacturer pin-description table when assigning PCB nets for the two inputs, supply rails, output, gain resistor, and reference or feedback connections. The package diagram should be cross-checked against the selected ordering code before fabrication, particularly when distinguishing the standard SO-8 assembly from lead-free or tape-and-reel order codes.
How is the gain of an LT1920IS8 configured?
The LT1920IS8 uses one external resistor to set its differential gain, with the supported range extending from 1 to 10,000. According to the Analog Devices LT1920 datasheet, this resistor-based approach reduces external component count compared with conventional dual-resistor gain networks. Choose the resistor value using the gain equation and operating-current guidance in the datasheet, then verify input bias current, resistor tolerance, noise contribution, and gain accuracy at the intended signal bandwidth.
Is the LT1920IS8 suitable for low-noise sensor measurement?
The LT1920IS8 is suitable for low-noise differential sensor measurement because its input noise is 7.5 nV/√Hz at 1 kHz and its gain accuracy reaches 30 ppm. The Analog Devices datasheet also identifies typical supply current as 0.9 mA, allowing low-noise performance without high quiescent power. It is especially appropriate for bridge outputs, strain gauges, and current-sense nodes where low offset and noise influence the accuracy of the extracted measurement.
What input protection does the LT1920IS8 support?
The LT1920IS8 can accept DC input fault voltages up to ±100 V when a 5 kΩ resistor is placed in series with each input. Analog Devices states that this configuration also provides 8 kV contact and 15 kV air-discharge ESD immunity and passes IEC 1000-4-2 level 4. Confirm the external resistor power rating and the complete signal-path impedance before applying this arrangement to continuously powered sensor inputs.
What is the difference between LT1920IS8 and AD620?
Analog Devices describes the LT1920 as a pin-for-pin and specification-for-specification improvement over the AD620, while its gain is programmed with one external resistor over a 1 to 10,000 range. The LT1920 also specifies 7.5 nV/√Hz input noise at 1 kHz and 0.9 mA typical supply current. Despite the compatibility claim, verify input common-mode range, output swing, supply limits, gain resistor equations, and package pin functions in both datasheets before replacing an existing design.
When should I choose LT1920IS8 over an alternative instrumentation amplifier?
Choose the LT1920IS8 when a design needs one-resistor gain setting, low input noise, and low supply current in an 8-pin SO footprint. Its 1 to 10,000 gain range, 30 ppm gain accuracy, and ±2.3 V to ±15 V supplies fit precision sensor and bridge circuits. Select an alternative instead when its input common-mode range, output swing, supply architecture, package dimensions, or protection method more closely matches a specialized system requirement.
Can an LT1920CS8 replace an LT1920IS8?
The LT1920CS8 is a temperature-grade variant in the same LT1920 family and uses the same 8-pin instrumentation-amplifier configuration. Its key electrical figures align with the LT1920’s 1 to 10,000 gain range, ±2.3 V to ±15 V supply capability, and single-resistor gain programming. Verify the manufacturer’s temperature-grade ratings and exact ordering-code requirements before using it in place of the industrial-grade LT1920IS8.
What can replace an LT1920IS8?
A replacement for the LT1920IS8 should use the same 8-pin SO footprint and provide compatible differential inputs, output, supply pins, gain setting, and operating limits. The LT1920CS8 and lead-free LT1920IS8#PBF ordering variants are direct same-family choices, while Analog Devices identifies the LT1920 as an improved AD620 replacement. Confirm the gain equation, reference behavior, common-mode range, output swing, noise, and temperature grade before treating any substitute as drop-in.
Is an AD620 a drop-in replacement for the LT1920IS8?
The Analog Devices LT1920 product page describes the LT1920 as a pin-for-pin and specification-for-specification improved replacement for the AD620. However, engineers should still compare the actual gain-setting resistor equation, supply voltage, input common-mode range, output swing, and reference-pin behavior. The 8-pin SO package enables a board-level substitution, but successful operation requires compatibility with the existing schematic rather than package appearance alone.
Is LT1920IS8 suitable for battery-powered instrumentation?
The LT1920IS8 is suitable for battery-powered instrumentation because Analog Devices specifies a typical supply current of 0.9 mA across a ±2.3 V to ±15 V supply range. Its 7.5 nV/√Hz input noise preserves sensitivity without requiring a high-current bias architecture. Low-voltage operation is possible from a 4.6 V total supply, but the output swing, input common-mode range, and quiescent current should be checked against the battery’s operating range.
Where can I buy LT1920IS8 and request a quote?
Use the Request a Quote form on this page to request LT1920IS8 pricing, stock confirmation, minimum order quantity, and lead time. Quote requests should include the exact LT1920IS8 ordering code, quantity, target package or packing format, and destination. Current commercial terms should be confirmed before placing an order because availability and lead time can change independently of the device’s technical specifications.
What is the price of LT1920IS8?
Current LT1920IS8 pricing is handled through the Request a Quote form on this page rather than a static price statement. Submit the required quantity, ordering suffix, shipment destination, and any reel or tube requirements to obtain a current quotation. The form is the appropriate place to confirm unit pricing, volume breaks, stock, and lead time because commercial conditions can change without altering the amplifier’s electrical characteristics.
What is the lead time and stock status for LT1920IS8?
Request current lead time, stock status, and minimum order quantity through the Request a Quote form on this page. Include the precise LT1920IS8 ordering code and required quantity because different suffix and packing designations may have separate inventory plans. The manufacturer product page and distributor listings indicate market availability, but a confirmed allocation and delivery schedule should be obtained before committing the design to a production build.

Data referensi kejuruteraan untuk LT1920IS8 — perbandingan, panduan rancangan, dan maklumat kesediaan

Panduan Pilihan

Choose the LT1920IS8 for precision differential measurements that need one-resistor gain programming, 7.5 nV/√Hz input noise at 1 kHz, and low typical supply current of 0.9 mA. Select LT1920CS8 when its commercial temperature grade is appropriate and verify the required environmental limits. Choose LT1920IS8#PBF when the lead-free ordering designation matches procurement and assembly requirements. Consider AD620 when its established gain network and circuit configuration are already present, but recalculate the gain resistor and verify common-mode range, output swing, and protection requirements. For a direct substitution, LT1920IS8 is most suitable when the design operates from ±2.3 V to ±15 V and the LT1920 single-resistor gain network is already designed. No alternative should be treated as drop-in without comparing the manufacturer pin descriptions, electrical limits, and gain equation.

Perbandingan dengan Gantian

Parametr Produk Ini LT1920CS8 LT1920IS8#PBF AD620
Brand Analog Devices Analog Devices Analog Devices Analog Devices
Package 8-pin SO 8-pin SO 8-pin SO 8-pin SO
Circuit Count 1 circuit 1 circuit 1 circuit 1 circuit
Gain Programming One external resistor One external resistor One external resistor External resistor gain network

Penyeberangsung Jelas

  • Single-resistor gain programming (vsAD620)
  • Low-noise operation at low supply current (vsAD620)
  • Documented protected-input operation (vsAD620)

Catatan Desain

Do not treat package compatibility as proof that the gain-setting network is interchangeable. The LT1920 uses one external resistor for gains from 1 to 10,000, while the AD620 uses a different resistor arrangement. Before substituting AD620 for LT1920IS8, recalculate the gain resistor, confirm the feedback and reference-pin behavior, and compare the input common-mode range and output swing. The Analog Devices product page identifies the LT1920 as an improved AD620 replacement, but circuit-level verification remains essential.

Route the differential input pair as a short, tightly coupled pair and connect the gain resistor close to the corresponding LT1920IS8 pin. Avoid routing these nodes beneath switching-regulator inductors, relay contacts, or digital return paths. Place input protection resistors ahead of the amplifier and preserve a low-impedance return for each source. These layout practices reduce conversion of common-mode interference into differential error and help the 7.5 nV/√Hz input-noise figure remain meaningful in the assembled circuit.

For field-wired inputs, use the Analog Devices protection configuration of one 5 kΩ series resistor at each input. This arrangement supports DC fault voltages up to ±100 V and provides 8 kV contact or 15 kV air-discharge ESD immunity, including IEC 1000-4-2 level 4 compliance as stated by the manufacturer. Check resistor power dissipation under the maximum sustained fault condition and add further attenuation if the sensor source can exceed the stated ±100 V limit.

Confirm the source can operate from a minimum total supply of 4.6 V and that the selected output level remains inside the output-swing limits at the required load current. The LT1920IS8 draws a typical 0.9 mA, making it suitable for low-power instrumentation, but total system demand includes protection resistors, sensor excitation, and external circuitry. Use local bypass capacitors close to the supply pins and verify settling behavior over the full measurement bandwidth rather than relying only on quiescent-current figures.

Maklumat Kesediaan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Bosong logam timbal
Unknown
Bosong halogen
Unknown
Mineral konflik
Unknown

Analog Devices specifies IEC 1000-4-2 level 4 ESD immunity when two external 5 kΩ input resistors are used. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not established by the cited product information.

Data disahkan pada: 2026-11-19 — data yang disahkan dan disusun semula oleh pasukan kejuruteraan komponen XAIPART

Pencarian Berhubungan

LT1920IS8 datasheet LT1920IS8 pinout LT1920IS8 datasheet pdf Analog Devices LT1920IS8 LT1920IS8 instrumentation amplifier LT1920IS8 gain resistor LT1920IS8 input noise LT1920IS8 supply voltage LT1920IS8 application circuit LT1920IS8 equivalent LT1920IS8 replacement LT1920IS8 vs AD620 LT1920IS8 price LT1920IS8 stock LT1920IS8 SO-8 pinout

Komponen dan Tanda berkaitan

Analog Devices LT1920 LT1920IS8 LT1920CS8 LT1920IS8#PBF AD620 precision instrumentation amplifier instrumentation amplifier analog signal-chain IC single-resistor gain programming differential amplifier common-mode rejection input voltage noise gain accuracy 7.5 nV/√Hz 30 ppm 0.9 mA ±2.3 V to ±15 V IEC 1000-4-2 level 4 8-pin SO SOIC-8 family surface mount strain-gauge bridge load-cell measurement industrial current sensing
RFRC Saring Pantas
Isikan butiran lengkap — pasukan jualan kami akan bertindak balas dalam masa 24 jam
Nombor Bahagian Pengeluar Pakej QTY Harga Target Lengkap
✓
Pesan diskon sudah disubmit!

Kami akan bertindak balas kepada emel anda dalam tempoh 24 jam

1
RFQ Diserahkan
2
kutipan Diterima
3
Order Dipesan
4
Pembayaran
5
Dihantar
6
Diantar
Lihat Perincian RFQ