LT1920IS8 - Precision Instrumentation Amplifier | Analog Devices
MPN: LT1920IS8 ✓ 啟用中LT1920IS8 概覽
An instrumentation amplifier is a specialized amplifier that measures the voltage difference between two input signals while rejecting common-mode voltage and interference. The LT1920 belongs to the instrumentation amplifier hierarchy within analog signal-chain ICs and combines a differential input stage, high-gain error amplifier, and output stage in one package. This integration reduces external component count compared with a discrete three-op-amp implementation while preserving gain accuracy over a wide range.
The LT1920 requires only one external resistor to establish gains from 1 to 10,000. Analog Devices specifies a gain accuracy of 30 ppm, supporting precise gain control in strain-gauge, bridge, and biomedical measurement systems. Its 7.5 nV/√Hz voltage noise at 1 kHz is maintained with typical power dissipation corresponding to 0.9 mA current. The dual-supply operating range of ±2.3 V to ±15 V also supports both low-voltage portable equipment and higher-voltage industrial instrumentation.
Input fault protection can be improved by placing an external 5 kΩ resistor in series with each input. Analog Devices states that this arrangement accepts DC input fault voltages up to ±100 V and raises ESD immunity to 8 kV contact and 15 kV air discharge. With two external 5 kΩ resistors, the LT1920 passes the IEC 1000-4-2 level 4 specification. This protection capability makes the amplifier useful where sensor inputs may be exposed to accidental overvoltage during field wiring or maintenance.
Typical applications include bridge-amplifier front ends, pressure and load-cell signal conditioning, battery-powered instrumentation, medical monitoring equipment, and precision current sensing. In a strain-gauge bridge, the small differential output can be amplified without the common-mode signal overwhelming the measurement. In portable equipment, the 0.9 mA typical supply current helps limit power consumption while retaining low input noise.
Design the gain resistor for the required differential gain and keep input and output layouts compact to minimize parasitic capacitance and noise pickup. Confirm the supply voltage, input common-mode range, output swing, and protection-resistor arrangement for the operating environment. The external series resistors are especially important when the source can present fault voltages above the amplifier input rating.
This page combines the manufacturer’s core LT1920 specifications with package details, protected-input design guidance, practical application patterns, and a compatibility-focused comparison. These engineering details help designers assess the LT1920IS8 for precision differential measurement, establish protection requirements, and determine whether a direct replacement satisfies both mechanical and electrical constraints.
直接替換替代品,適用於 LT1920IS8 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LT1920IS8 (相同外形與佔位) — 差異在於 Number of Circuits, Package, Supply Voltage Range.
LT1920CS8
✅ 直接替換📋 參考替代品(不在目錄中)
LT1920IS8#PBF
✅ 直接替換📋 參考替代品(不在目錄中)
LT1920IS8 最大額定值與電氣特性
| Device Type | Single-resistor gain-programmable precision instrumentation amplifier |
| Number of Circuits | 1 circuit |
| Gain Range | 1 to 10,000 |
| Gain Accuracy | 30 ppm |
| Input Voltage Noise | 7.5 nV/√Hz at 1 kHz |
| Typical Supply Current | 0.9 mA |
| Supply Voltage Range | ±2.3 V to ±15 V |
| Minimum Total Supply Voltage | 4.6 V |
| Maximum Total Supply Voltage | 30 V |
| Protected DC Input Fault Voltage | Up to ±100 V with external 5 kΩ input resistors |
| ESD Immunity | 8 kV contact and 15 kV air discharge with external 5 kΩ input resistors |
| ESD Standard | IEC 1000-4-2 level 4 |
| 封裝 | 8-pin SO |
| Package Pin Count | 8 pins |
| 安裝類型 | Surface mount |
| Temperature Grade | Industrial |
LT1920IS8 8 pins 腳位配置指南
LT1920IS8(8 pins 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: LT1920IS8.
請參閱 資料表 以查看完整腳位配置。
典型應用
LT1920IS8 適用於 6 應用s: Strain-Gauge Bridge Amplification, Precision Load-Cell Measurement, Medical Signal Conditioning, Battery-Powered Sensor Interface, Industrial Current Sensing, Protected Field-Sensor Front End.
Strain-Gauge Bridge Amplification
The LT1920IS8 suits strain-gauge bridges because it amplifies the small differential bridge output while rejecting the larger common-mode voltage. Its specified gain accuracy of 30 ppm and input noise of 7.5 nV/√Hz at 1 kHz help preserve weak mechanical measurements. The 8-pin SO package keeps the analog front end compact, while the ±2.3 V to ±15 V supply range accommodates both low-voltage portable systems and higher-voltage laboratory instrumentation. Confirm the bridge excitation level, output range, and gain resistor before deployment.
Precision Load-Cell Measurement
The LT1920IS8 provides the differential input and adjustable gain required for load-cell signal conditioning. A gain of 1 to 10,000 allows the same amplifier architecture to cover different transducer sensitivities and excitation voltages. Its 7.5 nV/√Hz noise at 1 kHz is valuable when the load-cell output is small, while the 0.9 mA typical supply current supports compact weighing and portable force-measurement equipment. Validate input common-mode range and output swing for the selected bridge resistance and excitation.
Medical Signal Conditioning
The LT1920IS8 is applicable to low-level medical sensor front ends where a differential signal must be amplified before conversion or isolation. Its 7.5 nV/√Hz input noise at 1 kHz reduces the amplifier contribution to the measurement floor, and single-resistor gain programming simplifies control circuitry. The device’s protected-input configuration can accept DC fault voltages up to ±100 V with external 5 kΩ resistors and meets IEC 1000-4-2 level 4 under the stated conditions. Final medical-system validation must consider applicable safety, isolation, and signal-integrity requirements.
Battery-Powered Sensor Interface
The LT1920IS8 fits battery-powered sensor interfaces because it combines low input noise with a typical supply current of 0.9 mA. Its minimum total supply of 4.6 V allows operation from regulated 5 V rails, while the ±15 V maximum supports higher-voltage industrial systems. With a 1 to 10,000 gain range, one compact 8-pin SO device can amplify pressure, temperature, or current-sense signals. Select the gain resistor and bypass capacitors to control power consumption and maintain accuracy across the battery’s discharge range.
Industrial Current Sensing
The LT1920IS8 can amplify the small differential voltage produced by a low-side or isolated current-sense element. The precision gain range of 1 to 10,000 supports adjustment from millivolt-level sensor outputs to higher full-scale voltages, and the 30 ppm gain accuracy helps reduce calibration error. Its low 7.5 nV/√Hz input noise helps preserve measurement resolution, while protected inputs are useful when wiring may be exposed to accidental voltage events. Confirm shunt common-mode voltage, Kelvin routing, and amplifier output limits.
Protected Field-Sensor Front End
The LT1920IS8 is useful in field-wired instrumentation where input cables can introduce ESD events or accidental DC faults. Analog Devices specifies that external 5 kΩ series resistors permit DC input fault voltages up to ±100 V and provide 8 kV contact or 15 kV air-discharge ESD immunity. The protection circuit does not replace normal overvoltage analysis, so verify resistor power dissipation and signal bandwidth. The 8-pin SO package allows the amplifier and protection components to be placed close to a compact sensor terminal board.
工程參考資料,適用於 LT1920IS8 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LT1920CS8 | LT1920IS8#PBF | AD620 |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 8-pin SO | 8-pin SO | 8-pin SO | 8-pin SO |
| Circuit Count | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Gain Programming | One external resistor | One external resistor | One external resistor | External resistor gain network |
主要差異化特點
- Single-resistor gain programming (對比AD620)
- Low-noise operation at low supply current (對比AD620)
- Documented protected-input operation (對比AD620)
設計說明
Do not treat package compatibility as proof that the gain-setting network is interchangeable. The LT1920 uses one external resistor for gains from 1 to 10,000, while the AD620 uses a different resistor arrangement. Before substituting AD620 for LT1920IS8, recalculate the gain resistor, confirm the feedback and reference-pin behavior, and compare the input common-mode range and output swing. The Analog Devices product page identifies the LT1920 as an improved AD620 replacement, but circuit-level verification remains essential.
Route the differential input pair as a short, tightly coupled pair and connect the gain resistor close to the corresponding LT1920IS8 pin. Avoid routing these nodes beneath switching-regulator inductors, relay contacts, or digital return paths. Place input protection resistors ahead of the amplifier and preserve a low-impedance return for each source. These layout practices reduce conversion of common-mode interference into differential error and help the 7.5 nV/√Hz input-noise figure remain meaningful in the assembled circuit.
For field-wired inputs, use the Analog Devices protection configuration of one 5 kΩ series resistor at each input. This arrangement supports DC fault voltages up to ±100 V and provides 8 kV contact or 15 kV air-discharge ESD immunity, including IEC 1000-4-2 level 4 compliance as stated by the manufacturer. Check resistor power dissipation under the maximum sustained fault condition and add further attenuation if the sensor source can exceed the stated ±100 V limit.
Confirm the source can operate from a minimum total supply of 4.6 V and that the selected output level remains inside the output-swing limits at the required load current. The LT1920IS8 draws a typical 0.9 mA, making it suitable for low-power instrumentation, but total system demand includes protection resistors, sensor excitation, and external circuitry. Use local bypass capacitors close to the supply pins and verify settling behavior over the full measurement bandwidth rather than relying only on quiescent-current figures.
合規資訊
Analog Devices specifies IEC 1000-4-2 level 4 ESD immunity when two external 5 kΩ input resistors are used. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not established by the cited product information.