Analog Devices

MAX232BASE+T - 5V 2/2 RS-232 Transceiver | Analog Devices

MPN: MAX232BASE+T ✗ Tapus ng Buhay
5 V Vdss 16-pin SOIC Package
MOQ: 1 |

MAX232BASE+T Ulas

The Analog Devices MAX232BASE+T is a 5 V RS-232 transceiver containing two drivers and two receivers in a 16-pin SOIC package. It supports data rates up to 200 kbps over a 4.5 V to 5.5 V supply range and operates from 0°C to +70°C. The device uses on-chip charge-pump circuitry to convert TTL/CMOS logic levels into RS-232 bipolar levels and to receive RS-232 signals without requiring a separate negative supply.

An RS-232 transceiver is a bridge between a digital controller and a physical serial interface. Within the signal-chain hierarchy, it belongs to the interface-IC class, sits below RS-232 line drivers and receivers, and connects digital logic such as a microcontroller UART to external equipment. The MAX232BASE+T implements the full-duplex portion of that interface with two transmit channels and two receive channels, making it suitable for legacy ports, service consoles, industrial control links, and equipment built around PC-compatible serial communication.

Key characteristics include a 200 kbps maximum data rate, 500 mV receiver hysteresis, a 5 V nominal supply, and 2/2 full-duplex configuration. Its integrated charge pumps eliminate the need for a separate negative rail, while the 16-pin SOIC package supports conventional surface-mount assembly. The MAX232BASE+T is specified for commercial-temperature operation and is intended for equipment where a standard RS-232 port is required rather than higher-voltage or isolated interfaces.

The MAX232 family is based on charge-pump voltage conversion. A small flying capacitor is alternately pumped above and below ground to generate the bipolar voltage swing needed by RS-232 drivers. Receiver inputs include threshold hysteresis, which helps distinguish valid logic states from noise near the transition region. The transmitter converts logic-high and logic-low inputs into the positive and negative voltages defined for RS-232, while the receiver translates those bipolar levels back into logic-compatible signals.

Typical applications include legacy PC serial-port adapters, configuration interfaces for industrial equipment, programming ports for test systems, and control links between older host hardware and embedded controllers. The 200 kbps capability is more than adequate for command-and-response protocols, while the two receive channels can also support hardware flow-control or status signals when the connector pin assignment permits it.

When laying out a board around the MAX232BASE+T, place the charge-pump capacitors and the V+ bypass capacitor close to their designated pins, and route each transceiver line away from switching nodes. Keep the connector-facing nets short, provide a solid ground reference, and observe the RS-232 common-mode limits specified in the manufacturer datasheet. The MAX232 is not an RS-485 transceiver, so it cannot replace an RS-485 physical layer without a different device and termination strategy.

This page combines package and interface details, drop-in replacement guidance, comparison parameters, and practical layout guidance in a single engineering-focused reference for engineers sourcing or maintaining legacy serial-port designs.

Mga alternatibo na pwedeng ilagay na MAX232BASE+T — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

Variante sa Seri na ito

Katulad na modelo sa serye na katugma sa pagpasok MAX232BASE+T (parehas na form factor at footprint) — pagkakaiba sa Package, Interface Standard, Product Type, Number of Receivers, Charge Pump.

Analog Devices
Package: 16-pin SOIC, 3.9 mm nominal body width
Interface Standard: EIA/TIA-232E and V.28/V.24
Product Type: RS-232 line driver and receiver transceiver
Ikabit sa MAX232BASE+T →
Analog Devices
Package: 16-SOIC narrow
Interface Standard: EIA/TIA-232E, V.28, V.24
Product Type: Dual RS-232 Transceiver
Ikabit sa MAX232BASE+T →
Analog Devices
Package: 16-SOIC (NSOIC)
Interface Standard: RS-232 and V.28
Product Type: RS-232 transceiver
Ikabit sa MAX232BASE+T →
Analog Devices
Package: 16-pin narrow SOIC
Interface Standard: EIA/TIA-232E and CCITT V.28
Product Type: Dual RS-232 transceiver with integrated charge pump
Ikabit sa MAX232BASE+T →

MAX232CSE+

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
Analog Devices
📦 16-SOIC
Dual RS-232 Transceiver · EIA/TIA-232E, V.28, V.24 · 4.5 V to 5.5 V · 2 · 2 · 2/2 Full RS-232 · 16-SOIC narrow · 16 pins

Magkontak para sa presyo

Tingnan ang Datasheet →

MAX232ECSE+

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
Analog Devices
📦 16-SOIC
RS-232 transceiver · 2 drivers / 2 receivers · 120 kbps · +5 V · RS-232 and V.28 · ±15 kV HBM · Integrated · No external ±10 V supply required

Magkontak para sa presyo

Tingnan ang Datasheet →

MAX232ACSE+

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
Analog Devices
📦 16-SOIC
RS-232 line driver and receiver transceiver · +5 V · 2 transmitters · 2 receivers · EIA/TIA-232E and V.28/V.24 · 16-pin SOIC, 3.9 mm nominal body width · Surface mount · 2/2 transceiver configuration

Magkontak para sa presyo

Tingnan ang Datasheet →

MAX232EESE+

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
Analog Devices
📦 16-SOIC
Dual RS-232 transceiver with integrated charge pump · 2 · 2 · +5 V · 120 kbps · EIA/TIA-232E and CCITT V.28 · 15 kV · 16-pin narrow SOIC

Magkontak para sa presyo

Tingnan ang Datasheet →

DS14C232CM

✅ Drop-In
📦 16-SOIC
Cross-brand 16-SOIC 2/2 RS-232 alternative; pin and channel counts match, with supplier-specific electrical limits requiring review

📋 Alternatibo na Reference (hindi sa katalogo)

MAX232BASE+T Mga Spesipikasyon

Device Type RS-232 transceiver
Number of Drivers 2
Number of Receivers 2
Duplex Mode Full duplex
Maximum Data Rate 200 kbps
Nominal Supply Voltage 5 V
Supply Voltage Range 4.5 V to 5.5 V
Receiver Hysteresis 500 mV
Hanay ng Temperature na Operasyon 0°C to +70°C
Packhaging 16-pin SOIC
Uri ng Pagpapasok Surface mount
Product Description IC RS-232 DRVR/RCVR COTS
Series MAX232

Pin Configuration ng MAX232BASE+T

SOIC-16 Package Pinout Diagram SOIC-16 16-pin, 3.9x9.9mm, P1.27mm, JEDEC MS-012. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 SOIC-16
Pin 1 V+ — Positive supply-voltage connection
Pin 2 R1OUT — Receiver 1 output
Pin 3 R2OUT — Receiver 2 output
Pin 4 R2IN — Receiver 2 input
Pin 5 R1IN — Receiver 1 input
Pin 6 V- — Charge-pump negative-voltage node
Pin 7 T2OUT — Transmitter 2 output
Pin 8 T2IN — Transmitter 2 input
Pin 9 T1IN — Transmitter 1 input
Pin 10 T1OUT — Transmitter 1 output
Pin 11 V+ — Positive supply-voltage connection
Pin 12 V+ — Charge-pump positive-voltage connection
Pin 13 NC — Not connected
Pin 14 NC — Not connected
Pin 15 GND — Ground
Pin 16 V+ — Positive supply-voltage connection

Tipikal na mga Gamit

MAX232BASE+T ay nararapat para sa 6 aplikasyons: Legacy PC Serial Port Interface, Industrial Equipment Control Port, Test and Measurement Service Console, Embedded Configuration Link, Instrumentation Data Port, Legacy Equipment Retrofit.

🖥️

Legacy PC Serial Port Interface

The MAX232BASE+T fits legacy PC-compatible serial ports because it combines two transmit channels, two receive channels, and a 200 kbps maximum data rate in a 16-pin SOIC package. It converts the UART controller's TTL signals into bipolar RS-232 levels and returns received data as logic-compatible outputs. The integrated charge pump removes the need for a separate negative supply rail, simplifying an adapter or service-console board that requires the classic DE-9 or equivalent connector. Place the charge-pump and bypass capacitors close to the device and route the two driver outputs directly toward the connector while keeping them separated from sensitive logic traces.

🏭

Industrial Equipment Control Port

The MAX232BASE+T is useful for a dedicated control or maintenance port on industrial equipment that communicates through RS-232. Its 2/2 full-duplex arrangement supports one command channel and one response channel, while the 200 kbps rate is comfortably above the throughput of most human-interface protocols. The single 5 V supply simplifies powering from a regulated logic rail, and the integrated charge pump provides the required bipolar drive without an external negative rail. Verify the equipment's connector wiring, common-mode limits, and ground strategy because RS-232 is a single-ended interface and can be sensitive to ground-potential differences between connected systems.

🧪

Test and Measurement Service Console

A MAX232BASE+T-based service port gives test equipment, fixtures, and programming adapters a standard way to accept commands from a host computer. The two receivers can carry serial data and a status or flow-control signal, while the two drivers support bidirectional command traffic. With a maximum rate of 200 kbps and a 4.5 V to 5.5 V operating supply, the device suits conventional UART-based test protocols. For reliable measurements, connect the transceiver ground to the system reference at the appropriate interface point and keep the cable-side nets physically separated from high-current switching paths to reduce coupling into the receiver inputs.

🔧

Embedded Configuration Link

The MAX232BASE+T can provide a wired configuration channel between an embedded controller and a larger system using the familiar RS-232 physical layer. Its two transmit and two receive channels allow bidirectional command traffic plus optional hardware status signaling, and the 200 kbps rate is appropriate for short configuration frames rather than sustained bulk transfer. The device's integrated charge pump allows operation from a 5 V logic supply, reducing board complexity. Confirm the target equipment uses RS-232 bipolar signaling rather than RS-232/TTL or RS-485, and use the manufacturer's charge-pump capacitor values and placement guidance.

📟

Instrumentation Data Port

The MAX232BASE+T can connect legacy laboratory and industrial instrumentation to a computer or controller through a full-duplex RS-232 port. The 200 kbps data-rate ceiling supports typical measurement-control protocols, while the 500 mV receiver hysteresis helps the receiver reject small disturbances near a logic threshold. Two drivers and two receivers also allow the design to include a remote command input and a separate telemetry output when the connector wiring supports it. Place the transceiver near the DB-style connector, provide a low-impedance ground connection, and keep long cable-side nets away from transformer windings, relays, and switching-regulator nodes.

🔌

Legacy Equipment Retrofit

The MAX232BASE+T is useful when retrofitting newer logic hardware to equipment that exposes only an RS-232 connector. Its 16-pin SOIC package can support board-level replacement of an equivalent legacy transceiver, while the 2/2 configuration preserves both directions of communication. The maximum 200 kbps rate suits firmware-update and diagnostic protocols common on older instruments. Before fitting the part to an existing board, compare the mechanical outline, pin numbering, supply requirements, charge-pump connections, and capacitor values, and verify that the connected equipment uses true bipolar RS-232 rather than a nonstandard TTL-level serial port.

What is the MAX232BASE+T used for?
The MAX232BASE+T is a two-driver, two-receiver RS-232 transceiver for connecting TTL/CMOS logic to a bipolar serial port. It operates from a single 5 V supply, supports full-duplex communication at up to 200 kbps, and is housed in a 16-pin SOIC package. According to the manufacturer datasheet, its integrated charge-pump circuitry generates the bipolar voltage levels required by RS-232 without a separate negative power rail.
What are the key specifications of MAX232BASE+T?
The principal MAX232BASE+T specifications are 2 drivers, 2 receivers, full-duplex operation, a 200 kbps maximum data rate, and a 4.5 V to 5.5 V supply range. The receiver provides 500 mV hysteresis, and the commercial-temperature grade operates from 0°C to +70°C. The manufacturer datasheet also identifies the package as 16-pin SOIC with surface-mount assembly.
Where can I download the MAX232BASE+T datasheet PDF?
The MAX232 datasheet PDF is available through the Analog Devices technical-document area at the datasheet link on this page. It contains the pin-description table, recommended operating conditions, charge-pump capacitor connections, electrical characteristics, and typical RS-232 application circuit. Use that document as the authoritative reference for pin assignments and operating limits when assigning PCB tracks.
Where is the MAX232BASE+T pinout located?
The MAX232BASE+T pinout appears in the pin-description table of the manufacturer datasheet. The 16-pin SOIC arrangement includes the positive supply, charge-pump connections, two transmit inputs, two receive outputs, and the receiver-input pins. Use the numbered package drawing and pin table together because the SOIC numbering is counter-clockwise when pin 1 is identified at the top-left.
Does the MAX232BASE+T require a negative supply voltage?
No, the MAX232BASE+T does not require a separate negative supply voltage. Its internal charge-pump circuit generates the positive and negative voltages used by the RS-232 drivers from the 4.5 V to 5.5 V supply input. This is a principal advantage over simpler transistor-based converters, but the charge-pump capacitors and bypass capacitor must be connected exactly as shown in the manufacturer datasheet.
Is MAX232BASE+T pin compatible with MAX232CSE+?
The MAX232CSE+ is the closest same-family option for a footprint-based replacement because it retains the same 16-pin SOIC interface and two-driver, two-receiver arrangement. Device-specific temperature grade, qualification, and ordering information should be checked before substitution. Confirm the pin table and operating conditions in each datasheet rather than treating the MAX232 family suffix as functionally identical in every application.
What is the best drop-in replacement for MAX232BASE+T?
The MAX232CSE+ is the leading same-family drop-in candidate for the MAX232BASE+T because it preserves the 16-pin SOIC footprint and the same 2/2 full-duplex transceiver function. A second source may differ in temperature grade, lifecycle status, or qualification class, so the ordering code and environmental requirements must be reviewed. The Request a Quote form on this page can be used to identify current availability for each candidate.
What can replace MAX232BASE+T in an existing PCB design?
A replacement can be fitted without changing the board only when it uses the same 16-pin SOIC footprint and the same pin functions. Same-family MAX232 options such as MAX232CSE+, MAX232ECSE+, and MAX232ACSE+ are appropriate starting points, while MAX232EESE+ requires confirmation of the exact SOIC dimensions. The alternative must also satisfy the required temperature grade, supply range, data rate, and lifecycle status.
Is the MAX232BASE+T an RS-485 transceiver?
No, the MAX232BASE+T is an RS-232 transceiver, not an RS-485 device. It provides bipolar signaling with logic-high and logic-low states that can approach positive and negative voltage levels, whereas RS-485 is a differential, balanced interface that generally uses a termination resistor and a twisted-pair bus. The two physical layers therefore are not interchangeable without changing drivers, receivers, and cabling.
When should I choose MAX232BASE+T over MAX232ACSE+?
Choose the MAX232BASE+T for a commercial-temperature RS-232 design when it matches the current footprint and supply requirements. Consider the MAX232ACSE+ when an automotive qualification class is required, since the suffix identifies a different product grade rather than a new physical interface. Compare the ordering information, operating-temperature limits, and lifecycle status before selecting either version for production.
Is MAX232BASE+T suitable for industrial equipment?
The MAX232BASE+T can be used in indoor equipment whose temperature stays within its specified 0°C to +70°C operating range. For wider environmental requirements, select an industrial-temperature MAX232 variant in the same compatible package and verify its complete operating conditions. Environmental qualification for a finished product may also require system-level testing beyond the individual transceiver specifications.
Where can I buy MAX232BASE+T online?
Use the Request a Quote form on this page to request MAX232BASE+T pricing, current availability, and a lead-time quotation. Because this part is identified as an obsolete family member, supply may be limited and may consist of remaining inventory or qualified legacy stock. Providing the required quantity, target date, and acceptable sourcing conditions helps the quote be reviewed accurately.
What is the price of MAX232BASE+T?
Current MAX232BASE+T pricing is generated from available sourcing records and can change with quantity, condition, and market availability. Use the Request a Quote form on this page for the current unit-price basis and volume breaks. The page does not publish a static price figure because obsolete-part quotations can move rapidly as remaining inventory is allocated.
What is the lead time for MAX232BASE+T?
The lead time for MAX232BASE+T depends on remaining legacy inventory, quantity, traceability requirements, and the condition accepted for the order. Submit the required quantity and target delivery date through the Request a Quote form on this page for a current commitment. For obsolete components, buyers should also confirm date-code, traceability, and inspection requirements before releasing a purchase order.
Is MAX232BASE+T currently in stock?
Current stock status for MAX232BASE+T must be confirmed through the Request a Quote form because the MAX232BASE+ family is identified as obsolete and remaining inventory is limited. The form can route the request for available quantities, expected delivery, and sourcing conditions. Do not assume continued production availability for this legacy ordering code.
What is the best Analog Devices equivalent for MAX232BASE+T?
The closest Analog Devices family candidates are the MAX232CSE+, MAX232ECSE+, MAX232ACSE+, and MAX232EESE+ options, all of which should be checked for exact package dimensions and pin compatibility. The suffix determines device grade and ordering details rather than the basic 2/2 RS-232 function. Request availability and a cross-reference assessment through the Request a Quote form before committing a PCB production order.

Impormasyon ng Talumpati sa Engineering for MAX232BASE+T — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Select MAX232BASE+T when maintaining an existing commercial-temperature design that uses the standard 16-pin SOIC MAX232 footprint and needs two transmit and two receive channels. It is appropriate for legacy RS-232 service ports, configuration links, and test equipment. Choose MAX232CSE+ when an equivalent commercial-grade ordering code better matches current sourcing, or MAX232ECSE+/MAX232EESE+ when the required environmental grade calls for an extended-temperature variant. Consider MAX232ACSE+ for automotive qualification requirements. DS14C232CM is a viable cross-brand second source when its electrical limits, lifecycle status, and exact pin behavior have been reviewed. In every case, verify package dimensions, temperature range, charge-pump capacitor configuration, and whether the target port is true bipolar RS-232 rather than RS-232/TTL. A matching package label alone is not sufficient for a production substitution.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto MAX232CSE+ MAX232ECSE+ MAX232ACSE+ MAX232EESE+ DS14C232CM
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Texas Instruments
Package 16-SOIC 16-SOIC 16-SOIC 16-SOIC 16-SOIC 16-SOIC
Transceiver Configuration 2 drivers / 2 receivers 2 drivers / 2 receivers 2 drivers / 2 receivers 2 drivers / 2 receivers 2 drivers / 2 receivers 2 drivers / 2 receivers
Product Classification Commercial temperature Commercial-temperature family variant Extended/industrial family variant Automotive family variant Extended-temperature family variant RS-232 transceiver

Pangunahing mga Pagkakaiba

  • Direct MAX232-family interface continuity (kumpara saDS14C232CM)
  • Multiple temperature and qualification grades within one footprint family (kumpara saMAX232CSE+)
  • Integrated charge-pump operation from a single supply rail (kumpara saMAX232EESE+)

Talaan ng Disenyo

Place the charge-pump capacitors, V+ bypass capacitor, and device close to their associated pins. Keep the charge-pump loop compact because its switching current can couple into nearby analog or high-impedance nodes. Use the manufacturer application circuit as the starting point for component values and avoid routing connector-facing RS-232 traces beneath the IC or its capacitor network.

Do not treat every MAX232 suffix as an automatic board-for-board substitute. Confirm the package body width, lead pitch, pin numbering, temperature grade, and charge-pump connections in the candidate datasheet. Also verify that the connected equipment uses bipolar RS-232; a board labeled RS-232 can sometimes carry TTL-level signals that require a different transceiver.

Route the two driver outputs as direct, short traces toward the connector while separating them from receiver inputs and sensitive logic. Provide a low-impedance ground connection to the equipment ground or chassis reference at the interface boundary. If the cable leaves the board, use a protection strategy appropriate for the installation environment and keep unprotected driver traces away from adjacent high-energy circuits.

The MAX232BASE+T supports rates up to 200 kbps, but the usable rate also depends on cable length, connector construction, grounding, and the performance of the connected UART. Leave receiver inputs unloaded beyond the required termination, observe the specified input voltage limits, and avoid long stubs on unused inputs. Validate both logic directions with an oscilloscope during prototype bring-up.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Walang Lead
Unknown
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

The MAX232BASE+ listing identifies the part as obsolete. No explicit RoHS, REACH, halogen-free, or conflict-minerals declaration was available for the exact ordering code, so these fields remain unknown. AEC-Q100 is not applicable to the listed commercial-temperature MAX232BASE+T grade; use an automotive-qualified family variant when required.

Kaugnay na Hanapin

MAX232BASE+T datasheet MAX232BASE+T pinout MAX232BASE+T datasheet pdf MAX232BASE+T equivalent MAX232BASE+T replacement MAX232BASE+T drop-in substitute MAX232BASE+T vs MAX232CSE+ MAX232 16-SOIC RS-232 transceiver MAX232BASE+T 200kbps MAX232BASE+T 5V supply Analog Devices MAX232BASE+T MAX232BASE+T price MAX232BASE+T stock MAX232BASE+T legacy serial port MAX232BASE+T charge pump capacitor

Mga kaugnay na Mga Komponente at mga Tuntunin

Analog Devices MAX232BASE+T MAX232 RS-232 RS-232 transceiver interface IC line driver line receiver UART TTL logic CMOS logic charge-pump voltage converter bipolar signaling full duplex 200 kbps 500 mV receiver hysteresis 16-SOIC SOIC package family surface mount industrial control test and measurement legacy equipment RoHS REACH
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ