MAX232EESE+ - 120kbps RS-232 Transceiver | Analog Devices
MPN: MAX232EESE+ ✗ Tapus ng BuhayMAX232EESE+ Ulas
An RS-232 transceiver is an interface IC that converts logic-level signals into bipolar RS-232 levels and converts incoming RS-232 signals back into logic levels. Within the interface hierarchy, MAX232EESE+ belongs to the RS-232 transceiver family of communication interface ICs. It is intended for EIA/TIA-232E and CCITT V.28 links where the endpoint equipment supplies low-voltage logic while the cable interface requires approximately positive and negative voltage signaling.
The MAX232EESE+ provides two transmit channels and two receive channels in one package. Its integrated voltage-generation circuitry lets the device operate from one +5 V rail without a separate negative supply. The manufacturer states that the MAX232E family meets EIA/TIA-232E and CCITT V.28 specifications at data rates up to 120 kbps when loaded. The MAX232E suffix also identifies the 15 kV ESD-protected version listed for the product.
The 16-pin narrow SOIC package supports compact, surface-mounted implementations and automated assembly. Because RS-232 is a single-ended, unbalanced interface, the transceiver simplifies the physical layer but does not provide galvanic isolation, common-mode rejection comparable to differential buses, or long-distance protection beyond the specifications of the MAX232E family. Circuit design should account for connector protection, cable transients, ground continuity, and unused driver or receiver inputs.
Typical uses include serial adapters, test and measurement instruments, programmable logic controllers, industrial control panels, and embedded equipment that previously relied on a legacy RS-232 port. A microcontroller can connect to the logic-side inputs and outputs, while the line-side pins connect through the DB9 or other RS-232 connector.
When laying out a design, place the device close to the connector and place its required charge-pump capacitors on the shortest practical signal paths. Keep the RS-232 traces away from clocks, switching regulators, and sensitive analog inputs. External protection may still be needed for severe industrial environments even though the device includes 15 kV ESD protection.
This page combines the manufacturer's MAX232E family information with interface-focused engineering guidance, package details, purchasing questions, and a practical evaluation of replacement options. It helps engineers determine whether the MAX232EESE+ fits an existing 16-pin SOIC RS-232 design before requesting a quote.
Mga alternatibo na pwedeng ilagay na MAX232EESE+ — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok MAX232EESE+ (parehas na form factor at footprint) — pagkakaiba sa Package, Product Type, Interface Standard, Supply Voltage, Data Rate.
Wala ng magagamit na drop-in alternatibo para sa produkto na ito.
Hilingin ang AlternatiboMAX232EESE+ Mga Spesipikasyon
| Product Type | Dual RS-232 transceiver with integrated charge pump |
| Number of Transmit Channels | 2 |
| Number of Receive Channels | 2 |
| Volte ng Pagbibigay | +5 V |
| Maximum Data Rate | 120 kbps |
| Interface Standard | EIA/TIA-232E and CCITT V.28 |
| ESD Protection | 15 kV |
| Packhaging | 16-pin narrow SOIC |
| Uri ng Pagpapasok | Surface mount |
Gabay sa Pin Configuration ng MAX232EESE+ 16-pin narrow soic
Pin configuration para sa MAX232EESE+ (16-pin narrow soic package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa MAX232EESE+.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
MAX232EESE+ ay nararapat para sa 6 aplikasyons: Industrial Serial Control Port, Test and Measurement Instrument, Data Acquisition Equipment, Programmable Logic Controller Interface, Point-of-Sale and Peripheral Equipment, Legacy Serial Adapter.
Industrial Serial Control Port
The MAX232EESE+ provides a compact two-channel RS-232 interface for industrial controllers, analyzers, and service equipment that must communicate with legacy RS-232 devices. Two driver channels and two receiver channels cover the common request, response, and status signaling arrangement used by older test instruments and controllers. Its single +5 V supply simplifies system power planning, while the integrated charge pump avoids a separate negative supply rail. Operation up to 120 kbps supports instrument-control protocols that do not require modern high-speed serial links. The 16-pin narrow SOIC reduces PCB area, but engineers should keep the line-side connections near the connector and verify industrial temperature and transient requirements in the manufacturer datasheet.
Inirekomenda
Test and Measurement Instrument
The MAX232EESE+ suits laboratory instruments that expose a legacy RS-232 configuration or control port. Its two transmitters can send commands and status information, while two receivers accept responses and handshaking signals. The stated 120 kbps maximum rate is appropriate for many legacy instrument-control protocols, and the +5 V architecture simplifies integration with digital logic and embedded controllers. The 15 kV ESD-protected E-series variant adds a useful layer of connector protection, although chassis grounding and external surge protection may remain necessary. Use a controlled ground reference between the equipment and connected device, and follow the manufacturer pin and capacitor guidelines in the layout.
Inirekomenda
Data Acquisition Equipment
The MAX232EESE+ can connect a data-acquisition controller or embedded logger to equipment using an RS-232 command interface. Two receive channels allow the controller to collect commands, acknowledgments, and measurements, while two transmit channels support configuration requests and control messages. A single +5 V supply and an on-chip charge pump reduce the number of external rails required near the connector. The 120 kbps capability is suitable for many low-bandwidth acquisition protocols and legacy peripheral links. Because RS-232 is unbalanced, maintain a common ground through the cable and place protection close to the connector when the port is exposed to user-accessible cables or electrically noisy industrial environments.
Inirekomenda
Programmable Logic Controller Interface
The MAX232EESE+ is useful in PLC communication modules and programmable controllers that need to interoperate with RS-232 printers, scanners, meters, or older programming equipment. The device converts between microcontroller logic levels and the positive and negative voltage signaling required by RS-232, including operation at rates up to 120 kbps. Its integrated charge pump allows implementation from one +5 V rail, reducing supply complexity in space-constrained control products. The surface-mount SOIC footprint supports automated assembly, but unused line-side channels should be handled exactly as directed by the manufacturer datasheet. For long cables or harsh installations, add appropriately coordinated connector protection and verify that the ground reference remains usable.
Inirekomenda
Point-of-Sale and Peripheral Equipment
The MAX232EESE+ can bridge a low-voltage controller to a legacy RS-232 peripheral such as a scanner, printer, display, or payment terminal. Two transmit and two receive channels provide useful flexibility for handshake, status, and command wiring while preserving the conventional RS-232 connector interface. The +5 V-powered charge-pump architecture simplifies integration into compact peripheral electronics, and the 16-pin SOIC leaves room for dense board layouts. The stated 120 kbps rate accommodates common peripheral-control traffic. Production designs should use the official pinout, include the required charge-pump capacitors, and apply ESD or surge protection at the exposed connector if the enclosure does not provide sufficient mechanical protection.
Inirekomenda
Legacy Serial Adapter
The MAX232EESE+ is appropriate for a compact USB-to-RS-232 or embedded serial adapter requiring two communication channels. It provides the electrical conversion between a modern controller's logic-level UART and a PC-style RS-232 connector while eliminating the need for a separate negative supply. Its 15 kV ESD protection is valuable in adapter applications because the external connector can receive direct user contact. The MAX232E family supports data rates up to 120 kbps, which covers many configuration and control protocols. Designers should still provide connector-side protection appropriate to the enclosure, use a low-ESR charge-pump capacitor layout, and maintain short RS-232 traces to minimize radiated noise and susceptibility to adjacent digital signals.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for MAX232EESE+ — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Talaan ng Disenyo
Place the MAX232EESE+ near the RS-232 connector and connect the line-side pins with short, direct traces. Position the charge-pump capacitors close to their specified IC pins with short ground returns, and route the connector ground to the interface ground reference without long loops. Keep clock, Ethernet, switching-power, and high-current traces away from receiver inputs because RS-232 is an unbalanced interface susceptible to coupled noise.
Do not infer a valid substitute from the MAX232 family name alone. A production replacement must match the 16-pin narrow SOIC dimensions and pin assignments, the MAX232E ESD requirement, supply limits, operating-temperature range, and intended data rate. The MAX232ESE+T listing uses the same family and package class, but its temperature-grade and ordering-suffix differences require datasheet review before it can be approved as a drop-in replacement.
The MAX232EESE+ provides 15 kV ESD protection, but the complete interface may still need connector-side surge and ESD protection for exposed industrial cables. Select the external protection to suit the required waveform and coordinate it with the device's operating ratings. A low-impedance chassis or signal-ground path is also important: poor ground continuity can increase susceptibility and make protection behavior less predictable.
Impormasyon ng Pagsunod sa Kautusan
The verified MAX232EESE+ listing identifies a 15 kV ESD-protected +5 V RS-232 transceiver in a 16-pin narrow SOIC. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not available for this exact ordering code.