Analog Devices

MAX232BASE+ 2/2 RS-232 Transceiver, 5V | Analog Devices

MPN: MAX232BASE+ ✓ Nakahanda
+5 V Vdss 16-pin SOIC, 0.154 in (3.90 mm) width Package
MOQ: 1 |

MAX232BASE+ Ulas

The Analog Devices MAX232BASE+ is a dual RS-232 transceiver containing two drivers and two receivers, powered from a single 5 V supply and housed in a 16-pin SOIC package. It uses an on-chip capacitive voltage generator to produce the positive and negative voltages required by the TIA/EIA-232-F interface. Each receiver converts an RS-232 input into a 5 V TTL/CMOS logic level, while each driver converts a TTL/CMOS input into a compliant RS-232 voltage.

An RS-232 transceiver is an interface IC within the broader hierarchy of interface ICs, serial communication ICs, and semiconductors. It bridges the voltage-domain difference between ordinary digital logic and the bipolar signal levels used by RS-232 links. This conversion allows equipment with a 5 V UART, microcontroller, or general-purpose logic port to communicate with legacy computers, industrial controllers, test systems, and other equipment using the RS-232 standard.

The MAX232BASE+ integrates four key interface functions: two line drivers and two line receivers. Its capacitive voltage generator allows a single +5 V supply to produce the positive and negative voltage levels needed by the drivers. According to the manufacturer datasheet, receiver logic threshold is typically 1.3 V with approximately 0.5 V of typical hysteresis. The receivers can also accept inputs up to ±30 V, providing tolerance for RS-232 voltage excursions.

The device's architecture combines TTL/CMOS-compatible logic-side signals with charge-pump-generated RS-232 levels. The charge pump requires external capacitors, while the receiver and driver sections perform level translation independently. This allows two bidirectional RS-232 channels to be implemented with one 16-pin device. Because the MAX232BASE+ operates from 5 V, it integrates naturally with 5 V UART logic without a separate negative supply for the interface converter.

Typical applications include legacy PC serial-port interfaces, industrial control panels, instrumentation, laboratory equipment, and embedded systems that retain an RS-232 connector. The MAX232BASE+ is especially useful when the host controller uses 5 V logic and the board requires two RS-232 lines rather than a larger multichannel transceiver. Its 16-pin SOIC package also allows a direct replacement strategy when the footprint and electrical behavior match.

Circuit design must provide the charge-pump capacitors and input/output bypass capacitance specified by the manufacturer datasheet. Keep the charge-pump loop compact because those pins carry high-frequency AC current. Connect the logic ground and interface-ground reference as directed by the device documentation, and route the RS-232 connector-side traces away from sensitive analog and clock circuitry to reduce noise pickup.

This page combines the confirmed device specifications, drop-in replacement candidates, package details, and practical circuit guidance for engineers evaluating the MAX232BASE+. It is intended to help with initial design selection, replacement planning, and PCB implementation rather than replace the complete pin-description table, ordering information, or absolute-maximum-rating tables in the manufacturer documentation.

Mga alternatibo na pwedeng ilagay na MAX232BASE+ — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

Variante sa Seri na ito

Katulad na modelo sa serye na katugma sa pagpasok MAX232BASE+ (parehas na form factor at footprint) — pagkakaiba sa Package, Product Type, Interface Standard, ESD Protection, Maximum Data Rate.

Maxim Integrated
Package: 16-SOIC
Product Type: RS-232 dual transceiver
Interface Standard: EIA/TIA-232E, V.28, V.24
Ikabit sa MAX232BASE+ →
Analog Devices
Package: 16-pin narrow SOIC
Product Type: Dual RS-232 transceiver with integrated charge pump
Interface Standard: EIA/TIA-232E and CCITT V.28
Ikabit sa MAX232BASE+ →
Texas Instruments
Package: 16-pin SOIC
Product Type: Dual RS-232 line driver and receiver
Maximum Data Rate: 120 kbit/s
Ikabit sa MAX232BASE+ →
Texas Instruments
Package: 16-SSOP, 5.30 mm width
Product Type: RS-232 line driver/receiver transceiver
Interface Standard: TIA/EIA-232-F and ITU V.28
Ikabit sa MAX232BASE+ →
Texas Instruments
Package: 16-pin SOIC
Product Type: Dual RS-232 line driver and receiver
Interface Standard: RS-232
Ikabit sa MAX232BASE+ →

MAX232EESE+

✅ Drop-In
Analog Devices
📦 16-pin SOIC
Dual RS-232 transceiver with integrated charge pump · 2 · 2 · +5 V · 120 kbps · EIA/TIA-232E and CCITT V.28 · 15 kV · 16-pin narrow SOIC

Magkontak para sa presyo

Tingnan ang Datasheet →

MAX232AESE+

✅ Drop-In
Maxim Integrated
📦 16-pin SOIC
RS-232 dual transceiver · 2 drivers · 2 receivers · 4.5 V to 5.5 V · +5 V · EIA/TIA-232E, V.28, V.24 · 2/2 full-duplex RS-232 · Enhanced CMOS

Magkontak para sa presyo

Tingnan ang Datasheet →

MAX232EIDR

✅ Drop-In
Texas Instruments
📦 16-pin SOIC
Dual RS-232 line driver and receiver · 2 · 2 · 5 V · 120 kbit/s · ±9 V · ±30 V · 1.0 µF

Magkontak para sa presyo

Tingnan ang Datasheet →

MAX3232ECDR

✅ Drop-In
Texas Instruments
📦 16-pin SOIC
Dual RS-232 line driver and receiver · 2 channels · 3 V to 5.5 V · 250 kbps · ±15 kV IEC ESD protection · RS-232 · 2 transmit and 2 receive functions · 16-pin SOIC

Magkontak para sa presyo

Tingnan ang Datasheet →

MAX3232CDBR

✅ Drop-In
Texas Instruments
📦 16-pin SOIC
RS-232 line driver/receiver transceiver · 2 · 2 · 3 V to 5.5 V · 250 kbit/s · 5 V logic · 300 uA · 0.1 uF

Magkontak para sa presyo

Tingnan ang Datasheet →

MAX232BASE+ Mga Spesipikasyon

Product Type Dual RS-232 driver and receiver
Driver Count 2 drivers
Receiver Count 2 receivers
Number of Transceivers 2/2 transceiver
Volte ng Pagbibigay +5 V
Receiver Input Tolerance ±30 V
Receiver Logic Threshold 1.3 V typical
Receiver Hysteresis 0.5 V typical
Output Logic Level 5 V TTL/CMOS
Interface Standard TIA/EIA-232-F
Packhaging 16-pin SOIC, 0.154 in (3.90 mm) width
Uri ng Pagpapasok Surface mount
Voltage Generator On-chip capacitive voltage generator

Gabay sa Pin Configuration ng MAX232BASE+ 16-pin soic, 0.154 in (3.90 mm) width

Pin configuration para sa MAX232BASE+ (16-pin soic, 0.154 in (3.90 mm) width package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.

Pinout diagram ng 16-pin soic, 0.154 in (3.90 mm) width package para sa MAX232BASE+

Wala ng detalyadong pinout data na magagamit para sa MAX232BASE+.

Sumangguni sa datasheet para sa buong pin configuration.

Tipikal na mga Gamit

MAX232BASE+ ay nararapat para sa 6 aplikasyons: Legacy PC Serial-Port Interface, Industrial Control Panel Interface, Laboratory Instrument Serial Link, Embedded UART-to-RS-232 Bridge, Instrumentation and Test Equipment, Service and Configuration Port.

🖥️

Legacy PC Serial-Port Interface

The MAX232BASE+ fits a legacy PC serial-port design that exposes two RS-232 channels from a 5 V UART or controller. Two drivers translate TTL/CMOS command and data signals into TIA/EIA-232-F levels, while two receivers convert the return signals back to 5 V logic. The integrated capacitive voltage generator derives the required bipolar voltages from one +5 V supply. With receiver inputs accepting up to ±30 V, the interface accommodates the voltage excursions characteristic of RS-232 links while keeping the host-side circuitry electrically simple.

🏭

Industrial Control Panel Interface

The MAX232BASE+ is suitable for an industrial controller or operator panel that must communicate with older RS-232 equipment. Its two transmitters support command output and status signaling, and its two receivers accept data from a remote controller. The single +5 V supply suits modern embedded electronics, while the charge-pump voltage generator removes the need for a separate negative supply rail. For deployment across industrial temperature ranges, engineers should verify the exact BASE+ temperature rating and consider MAX232EESE+ when its -40°C to +125°C specification satisfies the enclosure environment.

🔧

Laboratory Instrument Serial Link

The MAX232BASE+ provides a practical level-conversion stage for laboratory instruments that expose RS-232 connectors but internally operate with 5 V logic. The two drivers can carry measurement commands and configuration data, and the two receivers can return status or readings to a controller. The receiver threshold of 1.3 V typical and hysteresis of 0.5 V typical help distinguish valid signaling around the logic decision region. Keep the 16-pin SOIC close to the connector and place the charge-pump capacitors adjacent to the IC to prevent high-frequency charge-pump activity from coupling into sensitive measurement circuits.

🧩

Embedded UART-to-RS-232 Bridge

The MAX232BASE+ is well suited to connecting a 5 V embedded UART to a legacy RS-232 peripheral when only two communication lines are required. One driver converts UART transmit data, and one receiver converts the peripheral's response; the remaining driver and receiver can support a second channel or control signal. Because the transceiver operates from +5 V, it integrates easily with 5 V microcontroller and logic platforms. The implementation must include the specified external charge-pump capacitors and should preserve a common ground reference between the logic system and the RS-232 equipment.

📟

Instrumentation and Test Equipment

The MAX232BASE+ can bridge a test controller to instrumentation that retains an RS-232 command interface. Two RS-232 channels allow separate paths for commands and measurements or for primary and auxiliary equipment. The drivers generate the bipolar levels required by TIA/EIA-232-F, and the receivers provide 5 V TTL/CMOS outputs suitable for digital acquisition logic. To preserve measurement accuracy, route the bipolar connector-side traces away from analog input nodes, keep the charge-pump loop compact, and use the manufacturer bypass recommendations around the supply and interface pins.

🔌

Service and Configuration Port

The MAX232BASE+ is appropriate for adding a service or configuration port to a board that needs a standardized RS-232 connection. A system controller can transmit setup commands through one driver and receive diagnostic responses through one receiver, while the second pair supports bidirectional status communication. Using the same +5 V rail as the controller simplifies system power architecture, and the internal voltage generator provides the required positive and negative levels. Design the connector protection and grounding for the expected cable environment, and keep the high-voltage RS-232 routing separated from sensitive logic and analog nets.

What are the key specifications of MAX232BASE+ that engineers should know?
The MAX232BASE+ is a 2/2 RS-232 transceiver with two drivers, two receivers, a single +5 V supply, and a 16-pin SOIC package. According to the manufacturer datasheet, its receiver has a typical 1.3 V logic threshold, approximately 0.5 V hysteresis, and can accept ±30 V inputs. An integrated capacitive voltage generator produces the positive and negative levels required for TIA/EIA-232-F driver outputs. The device is intended to translate between 5 V TTL/CMOS logic and RS-232 voltage levels.
What is the operating voltage of MAX232BASE+?
The MAX232BASE+ operates from a single +5 V supply. According to the manufacturer datasheet, its capacitive voltage generator derives the positive and negative voltages required by the RS-232 drivers from that supply. Logic-side receiver outputs are converted to 5 V TTL/CMOS levels, while transmitter inputs accept 5 V TTL/CMOS signals. The circuit still requires the external charge-pump and bypass capacitors specified in the application information.
What is the operating temperature range of MAX232BASE+?
The MAX232BASE+ is identified by the manufacturer and distributor records as the BASE+ industrial-temperature version of the MAX232 family. Its exact operating-temperature limits should be confirmed in the ordering and absolute-maximum-rating tables for the exact MAX232BASE+ ordering code. Temperature-grade alternatives can include different suffixes, so an electrically similar part should not be substituted solely because its RS-232 channel count and package match. This distinction matters for industrial equipment operating outside consumer-temperature limits.
Where can I download the MAX232BASE+ datasheet PDF?
The MAX232BASE+ datasheet can be reached through the manufacturer documentation link associated with the MAX232 family. The document identifies the MAX232 as a dual driver and receiver with an on-chip capacitive voltage generator, a +5 V supply, a typical 1.3 V receiver threshold, approximately 0.5 V hysteresis, and receiver input tolerance up to ±30 V. Use the pin-description table, electrical characteristics, and application circuit in that document when assigning PCB pins and selecting external capacitors.
Where can I find the MAX232BASE+ pinout?
The MAX232BASE+ uses a 16-pin SOIC package, and its authoritative pin descriptions are located in the pin-configuration section of the manufacturer datasheet. The device combines charge-pump connections, supply and ground pins, two driver inputs and outputs, and two receiver inputs and outputs in one package. Use the package drawing and pin-description table together during PCB layout because exposed-pad or thermal-pad options are not implied by the 16-SOIC designation.
What can replace MAX232BASE+?
The closest replacements are MAX232-family devices in the same 16-pin SOIC footprint with two transmitters, two receivers, and 5 V operation. MAX232EESE+, MAX232AESE+, and MAX232EIDR provide same-package alternatives, while MAX3232ECDR and MAX3232CDBR are relevant MAX3232-family choices where their additional receiver features meet the design requirements. Verify the exact temperature grade, shutdown or fail-safe behavior, charge-pump capacitor requirements, and ordering suffix before approving a replacement.
Is MAX232BASE+ the same as MAX232EESE+?
No. MAX232BASE+ and MAX232EESE+ both belong to the MAX232 family and can share a 16-pin SOIC footprint, but their ordering suffixes identify different temperature or qualification grades. MAX232EESE+ is identified as an extended-temperature part operating from -40°C to +125°C, whereas the exact MAX232BASE+ limits must be checked in its ordering table. For a direct substitution, verify both the temperature envelope and whether the original design uses any grade-specific feature.
What is the best MAX3232-family equivalent for MAX232BASE+?
MAX3232ECDR is a relevant 5 V, two-driver and two-receiver alternative when its receiver features are acceptable. It uses the same broad interface role as the MAX232BASE+, converts between logic and RS-232 levels, and provides a same-package migration path in 16-pin SOIC format. The important tradeoff is that the MAX3232 family is selected when its enhanced receiver or power-management characteristics add value. Confirm pin-level behavior, external capacitor configuration, temperature grade, and flow-control requirements before treating it as a drop-in replacement.
When should I choose MAX232BASE+ over a MAX3232 alternative?
Choose MAX232BASE+ when a conventional two-channel, 5 V RS-232 interface is required and the design already follows the MAX232 application circuit. Choose a MAX3232-family option instead when its enhanced receiver behavior or other documented features provide a clear system benefit. Both approaches can use a 16-pin SOIC footprint, but the shared package does not by itself guarantee identical behavior. Review the pin descriptions and electrical characteristics, especially around receiver thresholds, shutdown, fail-safe operation, and charge-pump capacitance.
Can MAX232EIDR replace MAX232BASE+ in an existing PCB?
MAX232EIDR can be evaluated as a drop-in replacement because it provides the same two-transmitter, two-receiver RS-232 function in a 16-pin SOIC package. The confirmed architectural differences are zero in transceiver count and zero in supply-voltage difference, while the MAX232EIDR ordering code indicates an extended-temperature grade. Before substitution, compare the exact temperature limits, pin descriptions, absolute maximum ratings, and charge-pump capacitor recommendations for both orderable parts. Existing board changes should not be necessary when every electrical and layout check passes.
Where can I buy MAX232BASE+ online?
The current commercial channel for MAX232BASE+ is the Request a Quote form on this product page. Submit the exact MPN, desired package suffix, quantity, and target delivery date so the order can be matched without changing the electrical variant. Current stock, order acknowledgment, and lead time should be confirmed through the quote process rather than assumed from a historical catalog entry. The manufacturer part number MAX232BASE+ should be retained exactly on the purchase order.
What is the price of MAX232BASE+?
Use the Request a Quote form on this page to obtain the current unit price and quantity availability for MAX232BASE+. The structured pricing area on this page is the appropriate source for the live commercial figure because component pricing can change with quantity, inventory, market conditions, and packaging requirements. For an engineering estimate, specify the required order quantity, date code preference, and whether reel, tube, or another approved delivery format is required.
Is MAX232BASE+ in stock and what is its lead time?
Request current stock and lead-time confirmation through the Request a Quote form on this page. Provide the quantity, production schedule, and acceptable date-code window so procurement can return a meaningful availability response. Inventory status should not be inferred from historical catalog availability or from the existence of a product page. For prototype work, include the requested ship date; for production, include forecast quantities and any required traceability or inspection documentation.
How does the MAX232BASE+ capacitive voltage generator affect PCB layout?
The MAX232BASE+ charge-pump section should be laid out with very short connections between the charge-pump pins and their external capacitors. According to the manufacturer application guidance, those capacitors and the associated IC pins form a high-frequency current loop, so long traces and large loop area can increase radiated noise or reduce margin. Place the capacitors close to the device, use short ground-return paths, and avoid routing the charge-pump loop beneath sensitive analog inputs or long protected communication lines.
What design considerations matter for MAX232BASE+ RS-232 links?
Provide the charge-pump capacitors, supply bypass, and interface bypass capacitors specified by the manufacturer. Keep the connector-side RS-232 traces away from clocks, sensors, and precision analog inputs because the driver outputs are bipolar and can couple noise into nearby circuits. Confirm the logic-side UART voltage levels are compatible with 5 V TTL/CMOS inputs, and verify the board ground strategy against the application schematic. Robustness testing should include both logic-side traffic and the receiver's ±30 V input tolerance.

Impormasyon ng Talumpati sa Engineering for MAX232BASE+ — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose MAX232BASE+ when the design needs a conventional two-driver, two-receiver RS-232 interface powered from +5 V and already uses the MAX232 charge-pump circuit. Choose MAX232EESE+ or MAX232EIDR when an extended-temperature ordering option is required for the installation environment; verify the exact limits and orderable suffix before replacing the BASE+ part. Choose MAX232AESE+ for a same-family, same-package sourcing alternative after checking its grade-specific characteristics. Consider MAX3232ECDR or MAX3232CDBR when enhanced receiver behavior provides meaningful benefit, such as improved tolerance of a particular off-state input condition. A shared 16-pin SOIC footprint makes all five candidates mechanically convenient, but PCB reuse still requires checking pin functions, supply voltage, receiver thresholds, temperature range, fail-safe behavior, and external capacitor requirements. For production, avoid selecting a replacement solely from package shape or channel count.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto MAX232EESE+ MAX232AESE+ MAX232EIDR MAX3232ECDR MAX3232CDBR
Package 16-pin SOIC, 0.154 in (3.90 mm) width 16-pin SOIC 16-pin SOIC 16-pin SOIC 16-pin SOIC 16-pin SOIC
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Supply Voltage +5 V +5 V +5 V +5 V +5 V +5 V
Interface Standard TIA/EIA-232-F RS-232 RS-232 RS-232 RS-232 RS-232
Special Receiver Features Conventional RS-232 receiver Conventional RS-232 receiver Conventional RS-232 receiver Conventional RS-232 receiver Enhanced MAX3232 receiver Enhanced MAX3232 receiver

Pangunahing mga Pagkakaiba

  • Conventional two-channel MAX232 interface (kumpara saMAX3232ECDR)
  • Established MAX232 family compatibility (kumpara saMAX232AESE+)
  • Wide receiver input tolerance (kumpara saMAX232EIDR)

Talaan ng Disenyo

Place the charge-pump capacitors immediately beside their associated MAX232BASE+ pins and keep the high-frequency loop as small as practical. The capacitive voltage generator switches current between the external capacitors and the device, so long traces and a large loop area can increase EMI and couple noise into nearby circuits. Route the connector-side driver and receiver traces away from precision analog inputs, oscillator nodes, and sensitive timing signals.

Follow the manufacturer circuit for the charge-pump capacitors, interface bypass capacitors, and supply decoupling. Use a low-impedance +5 V connection and place the local bypass capacitor close to the supply pins to suppress switching noise from the voltage generator. Account for capacitor tolerance and effective DC bias when selecting ceramic parts, because changing the capacitance can affect charge-pump performance and the resulting RS-232 output levels.

Do not treat a shared SOIC footprint as sufficient proof that every MAX232 and MAX3232 suffix is interchangeable. Compare the pin descriptions, temperature grade, receiver threshold and hysteresis, shutdown or fail-safe behavior, absolute maximum ratings, and external capacitance requirements. In particular, confirm that the selected replacement retains the required two transmitter channels, two receiver channels, +5 V operation, and acceptable behavior for the RS-232 signals present on the board.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Walang Lead
Unknown
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

The MAX232BASE+ is a commercial RS-232 interface IC; automotive qualification is not applicable to this grade. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status should be confirmed against the exact manufacturer product documentation and declaration.

Data napatotohanan sa: 2026-11-17 — impormasyon na pinatunayan at pinapatakbo ng pangkat ng engineering ng XAIPART's component engineering team

Kaugnay na Hanapin

MAX232BASE+ datasheet MAX232BASE+ pinout MAX232BASE+ datasheet pdf MAX232BASE+ replacement MAX232BASE+ equivalent MAX232BASE+ cross reference MAX232BASE+ 16-SOIC pinout MAX232BASE+ vs MAX232EESE+ MAX232BASE+ vs MAX3232ECDR Analog Devices MAX232BASE+ MAX232BASE+ 5V RS-232 transceiver MAX232BASE+ application circuit MAX232BASE+ price MAX232BASE+ stock

Mga kaugnay na Mga Komponente at mga Tuntunin

Analog Devices MAX232BASE+ MAX232EESE+ MAX232AESE+ MAX232EIDR MAX3232ECDR MAX3232CDBR RS-232 TIA/EIA-232-F RS-232 transceiver interface IC serial communication IC semiconductor TTL/CMOS logic capacitive voltage generator charge-pump capacitor receiver threshold receiver hysteresis 16-pin SOIC SOIC package family surface-mount package industrial control laboratory instrumentation legacy serial port
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ