Texas Instruments

MAX3232EIDBE4 - 3-5.5V 2/2 RS-232 Transceiver | Texas Instruments

MPN: MAX3232EIDBE4 ✓ Nakahanda
3 V to 5.5 V Vdss 16-SSOP (0.209 inch, 5.30 mm width) Package
MOQ: 1 |

MAX3232EIDBE4 Ulas

The Texas Instruments MAX3232EIDBE4 is a 3 V to 5.5 V multichannel RS-232 line driver and receiver with two drivers, two receivers, and ±15 kV IEC ESD protection, housed in a 16-SSOP package. It supports the RS-232 interface for industrial-control, communications, and embedded systems while operating across the extended temperature range of −40°C to +85°C.

An RS-232 transceiver is an interface IC that combines differential signal generation and reception for serial communications. It belongs to the line-driver/receiver hierarchy within interface ICs, bridging a host UART or processor logic-level port and a wired RS-232 connection. The MAX3232EIDBE4 is intended for designs that need both transmit and receive functions on one compact, surface-mount device.

Key features include a 3 V to 5.5 V supply range, a 2/2 driver-and-receiver configuration, and bus-pin ESD protection rated to ±15 kV using the IEC 61000-4-2 contact-discharge and air-gap-discharge protection referenced in the product description. The 16-SSOP package measures approximately 5.30 mm in width and 0.209 inch in body width. The part is packaged in a tube according to the product listing.

The E designation identifies the enhanced MAX3232E family, which Texas Instruments describes as an improved direct drop-in replacement for the original MAX3232. Its integrated charge-pump circuitry supports level translation between low-voltage digital logic and RS-232 signal levels without requiring a separate ±12 V supply. This simplifies interface implementation while retaining the voltage ranges and peripheral arrangement expected in MAX3232-class designs.

Typical applications include RS-232 connections between embedded controllers and test equipment, industrial serial consoles, point-of-sale terminals, instrumentation, and legacy peripheral adapters. The two-driver and two-receiver arrangement supports full-duplex point-to-point links, provided the system designer accounts for the directional nature of each channel and applies appropriate interface protection where cables leave an enclosure.

When designing a board around the MAX3232EIDBE4, preserve the manufacturer-recommended charge-pump capacitor connections and place the associated ceramic capacitors close to their pins. Confirm that the external connector, cable, and grounding strategy match the intended RS-232 application, because the integrated IC protects its bus pins but cannot compensate for an inadequate enclosure or cable shield.

This page combines the device specifications, verified source links, package identification, application guidance, and confirmed same-package alternatives needed to evaluate the MAX3232EIDBE4. It also highlights where a replacement can be used without changing the 16-SSOP land pattern and where temperature, packing, or parameter differences still require engineering review.

Mga alternatibo na pwedeng ilagay na MAX3232EIDBE4 — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

MAX3232EIDBR

✅ Drop-In
Texas Instruments
📦 16-SSOP (0.209, 5.30mm Width)
Dual RS-232 line driver and receiver · 2 channels · 2 channels · 3 V to 5.5 V · 250 kbit/s · 30 V/µs maximum · ±15 kV IEC ESD protection · TIA/EIA-232-F

Magkontak para sa presyo

Tingnan ang Datasheet →

MAX3232EIDR

✅ Drop-In
Texas Instruments
📦 16-SSOP (0.209, 5.30mm Width)
Dual RS-232 line driver/receiver transceiver · 2 drivers · 2 receivers · 250 kbps · 3 V to 5.5 V · 3.3 V · RS-232 · ±15 kV

Magkontak para sa presyo

Tingnan ang Datasheet →

MAX3232EIDBE4 Mga Spesipikasyon

Product Type Multichannel RS-232 line driver/receiver
Number of Drivers 2
Number of Receivers 2
Transceiver Configuration 2/2
Supply Voltage Range 3 V to 5.5 V
Interface Standard RS-232
ESD Protection ±15 kV
ESD Test Method IEC 61000-4-2 contact discharge and air-gap discharge
Packhaging 16-SSOP (0.209 inch, 5.30 mm width)
Packaging Tube
Hanay ng Temperature na Operasyon −40°C to +85°C
Uri ng Pagpapasok Surface mount
Lead-Free Status Lead free

Gabay sa Pin Configuration ng MAX3232EIDBE4 16-ssop (0.209 inch, 5.30 mm width)

Pin configuration para sa MAX3232EIDBE4 (16-ssop (0.209 inch, 5.30 mm width) package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.

Pinout diagram ng 16-ssop (0.209 inch, 5.30 mm width) package para sa MAX3232EIDBE4

Wala ng detalyadong pinout data na magagamit para sa MAX3232EIDBE4.

Sumangguni sa datasheet para sa buong pin configuration.

Tipikal na mga Gamit

MAX3232EIDBE4 ay nararapat para sa 6 aplikasyons: Industrial RS-232 Control Port, Embedded Serial Console, Test and Measurement Instrument, Point-of-Sale Terminal Interface, RS-232-to-Industrial Peripheral Link, Legacy Peripheral Adapter.

🏭

Industrial RS-232 Control Port

The MAX3232EIDBE4 fits an industrial controller that must communicate through a legacy RS-232 port while operating from a 3.3 V or 5 V logic rail. Its two drivers and two receivers support a full-duplex point-to-point connection, and the −40°C to +85°C operating range suits equipment expected to operate across industrial temperature conditions. Place the device between the host UART and the DE/RE-controlled transceiver direction logic, then follow the manufacturer charge-pump capacitor layout. The documented ±15 kV IEC ESD protection is valuable at the IC bus pins, although the finished enclosure must provide the primary mechanical protection for field-wired connectors.

🖥️

Embedded Serial Console

An embedded Linux controller or microcontroller platform can use the MAX3232EIDBE4 to expose a service console through RS-232. The device accepts a 3 V to 5.5 V supply and includes both transmit and receive channels, allowing the host UART to exchange commands and diagnostic data with a PC or service terminal. The 16-SSOP package supports compact board layouts, while integrated ESD protection adds resilience to the transceiver interface. Maintain short signal traces, use the specified charge-pump capacitors, and isolate the logic ground and cable return correctly to avoid interpreting ground offsets as data errors.

🔧

Test and Measurement Instrument

The MAX3232EIDBE4 is useful in test and measurement instruments that communicate with a host PC, printer, or calibration system through RS-232. Two drivers and two receivers provide the channels required for a bidirectional instrument link, and the 3 V to 5.5 V supply range supports both 3.3 V and 5 V instrument architectures. The extended −40°C to +85°C range can serve laboratory-adjacent equipment with wider environmental requirements. Confirm the UART baud-rate support, logic thresholds, and timing limits from the manufacturer datasheet, and route the external connector through a layout that minimizes exposed copper and provides a controlled return path.

🛒

Point-of-Sale Terminal Interface

A point-of-sale terminal can use the MAX3232EIDBE4 when a receipt printer, customer display, or service accessory still relies on RS-232. The dual-driver, dual-receiver arrangement supports the bidirectional signal paths commonly found in point-of-sale equipment, and the 5.5 V upper supply limit accommodates established 5 V control systems. The integrated ±15 kV IEC ESD protection is especially relevant when accessories connect through external cables. The IC does not make a poorly grounded cable reliable, however, so use appropriate shielding, connector selection, and chassis grounding. Confirm the host UART logic levels and directional-control sequence before finalizing the schematic.

⚡

RS-232-to-Industrial Peripheral Link

The MAX3232EIDBE4 can bridge a low-voltage controller and an RS-232-equipped industrial peripheral such as a drive interface, programmable instrument, or legacy controller. Its two channels provide separate transmit and receive paths, while the 3 V to 5.5 V supply supports modern embedded logic without a separate bipolar power rail. The −40°C to +85°C range supports equipment intended for extended industrial environments. Apply the manufacturer’s capacitor placement rules, avoid long unprotected branches where possible, and verify that the peripheral’s driver and receiver definitions agree with the MAX3232E channel orientation. Cable transients and ground offsets must be handled at the system interface.

🔌

Legacy Peripheral Adapter

A compact legacy-peripheral adapter can be built around the MAX3232EIDBE4 when an existing RS-232 device must connect to a modern USB-to-serial or embedded controller. The transceiver provides two RS-232 drivers and two receivers while operating from the same 3.3 V or 5 V domain used by many compact adapters. The 16-SSOP package helps limit board area, and integrated bus-pin ESD protection improves interface robustness. Design the adapter so that direction-control lines have defined states during reset, keep the RS-232 side away from sensitive analog circuitry, and confirm the adapter connector’s pin assignment. Validate the completed cable assembly for ground-offset and ESD requirements.

What is the MAX3232EIDBE4?
The MAX3232EIDBE4 is a Texas Instruments RS-232 transceiver containing two line drivers and two receivers in a 16-SSOP package. According to the manufacturer product description, it operates from 3 V to 5.5 V and provides ±15 kV IEC ESD protection on its RS-232 bus pins. It converts low-voltage logic signals into RS-232 levels and converts incoming RS-232 signals back into logic-compatible levels.
What are the key specifications of MAX3232EIDBE4 that engineers should know?
The MAX3232EIDBE4 is a 3 V to 5.5 V, 2/2 RS-232 transceiver in a 16-SSOP package. Its documented highlights are ±15 kV IEC ESD protection, an operating-temperature range of −40°C to +85°C, and a lead-free status. The 16-SSOP body is identified as 0.209 inch wide, or 5.30 mm, and the component is supplied in tube packaging. Use these points to confirm electrical, environmental, and PCB compatibility.
Where can I download the MAX3232EIDBE4 datasheet PDF?
The MAX3232EIDBE4 datasheet can be downloaded from the Texas Instruments document listing linked on this page. The manufacturer describes the device as a 3 V to 5.5 V multichannel RS-232 line driver and receiver with ±15 kV IEC ESD protection. When downloading, verify that the document identifies MAX3232EIDBE4 and includes the 16-SSOP pin description, electrical characteristics, charge-pump capacitors, and ESD test conditions.
Where can I find the MAX3232EIDBE4 pinout?
The MAX3232EIDBE4 pin assignment is documented in the 16-SSOP section of the manufacturer datasheet. The device is a 2/2 transceiver, so the diagram should identify the two driver outputs, two receiver inputs, supply pins, ground pins, charge-pump connections, and enable-related functions. Use that pin-description table for PCB routing rather than assigning functions from the receiver and driver counts alone.
What is the supply voltage range of MAX3232EIDBE4?
The MAX3232EIDBE4 operates from 3 V to 5.5 V. This range allows the device to work from common 3.3 V and 5 V system rails while producing the bipolar voltage levels required by an RS-232 interface. The power architecture and charge-pump capacitors still require correct polarity, adequate bypassing, and the placement specified in the manufacturer datasheet.
Is MAX3232EIDBE4 suitable for industrial equipment?
The MAX3232EIDBE4 is suitable for industrial applications requiring RS-232 connectivity and an extended temperature range of −40°C to +85°C. Its ±15 kV IEC ESD protection strengthens the bus interface, but enclosure design, cable shielding, grounding, and surge protection remain system-level responsibilities. Confirm the complete production electrical limits and required certifications against the finished equipment specification.
What can replace the MAX3232EIDBE4?
The MAX3232EIDBE4 can be replaced by the MAX3232EIDBR when the existing 16-SSOP land pattern, terminal arrangement, and core operating requirements remain unchanged. The manufacturer describes the MAX3232E family as an improved direct drop-in replacement for the original MAX3232. For MAX3232EIDBR, confirm temperature grade, packing format, supply ordering code, and current lifecycle status before releasing the substitution into production.
Is MAX3232EIDBE4 the same as MAX3232EIDBR?
MAX3232EIDBE4 and MAX3232EIDBR use the same 16-SSOP package and are identified as having consistent terminals and package characteristics. Their practical interchangeability still depends on the orderable packing method and any temperature-grade difference encoded by the suffix. Compare the manufacturer ordering information for every parameter affected by the package and marking codes before making a permanent substitution.
MAX3232EIDBE4 vs MAX3232EIDR - which is better for an industrial RS-232 port?
MAX3232EIDBE4 is the better choice when the required orderable configuration is supplied in a tube and meets the documented −40°C to +85°C range. MAX3232EIDR is a confirmed same-package option, but its packing and orderable suffix must be checked before substitution. The decisive engineering checks are the package footprint, terminal arrangement, operating-temperature grade, lifecycle status, and availability plan.
When should I choose MAX3232EIDBE4 over MAX3232EIDBR?
Choose MAX3232EIDBE4 when the approved bill of materials specifically requires its orderable suffix and tube packaging. Choose MAX3232EIDR only after verifying that its packing method, temperature grade, lead-free status, and lifecycle position satisfy the production requirements. Because both use the 16-SSOP footprint, the substitution should not require a PCB land-pattern change, but administrative and qualification checks remain necessary.
Is MAX3232EIDBE4 suitable for a 3.3 V UART interface?
The MAX3232EIDBE4 is suitable for a 3.3 V UART interface because its documented supply range includes 3 V. The UART still operates at logic-compatible levels, while the transceiver performs the conversion to and from RS-232 levels. Verify signal polarity, receiver thresholds, driver slew behavior, and the exact connection to the host UART using the datasheet pin and timing information.
What design considerations matter for MAX3232EIDBE4?
The principal layout requirement is to follow the manufacturer’s charge-pump and bypass-capacitor configuration exactly. Place the specified capacitors close to their associated pins, keep the RS-232 traces short where practical, and provide an appropriate return path. The integrated ±15 kV ESD protection helps at the IC bus pins, but it does not replace a sound enclosure, cable shield, or correctly engineered ground strategy.
Does MAX3232EIDBE4 require external ±12 V power?
The MAX3232EIDBE4 operates from a single 3 V to 5.5 V supply and does not require an external ±12 V rail for its stated RS-232 interface function. Its integrated level-shifting and charge-pump circuitry produces the required signal levels. The associated external capacitors are still mandatory, and their values, voltage ratings, and placement must follow the manufacturer datasheet.
Where can I buy MAX3232EIDBE4 and check current availability?
Current commercial availability for MAX3232EIDBE4 should be requested through the Request a Quote form on this page. The quote team can confirm the requested orderable suffix, tube packaging, quantity, current lifecycle position, and expected delivery schedule. Submit the complete MPN MAX3232EIDBE4 when requesting a quotation to avoid ambiguity with related MAX3232E variants.
What is the price of MAX3232EIDBE4?
The current commercial terms for MAX3232EIDBE4 are available through the Request a Quote form on this page. Request the exact MPN and required quantity so the quotation reflects the correct package suffix and packaging configuration. Because market pricing and availability can change, use the submitted quote rather than a historical listing figure when planning a production purchase.
What is the lead time for MAX3232EIDBE4?
The current lead time for MAX3232EIDBE4 should be confirmed through the Request a Quote form on this page. Include the required quantity, tube packaging requirement, target delivery date, and any approved alternate-source policy. The manufacturer’s component ordering and lifecycle information should be checked before committing a schedule, especially if a single-source part is required for an active production program.
Is MAX3232EIDBE4 in stock?
The current stock position for MAX3232EIDBE4 can be requested through the Request a Quote form on this page. Provide the exact MPN and anticipated order quantity so inventory can be matched to the correct orderable suffix and tube packaging. Do not infer production availability from a generic distributor landing page; use the quotation response for the quantity and delivery plan you need.

Impormasyon ng Talumpati sa Engineering for MAX3232EIDBE4 — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose MAX3232EIDBE4 when the production BOM requires the exact orderable suffix, tube packaging, and a documented −40°C to +85°C operating range. Its 3 V to 5.5 V supply, two drivers, two receivers, and ±15 kV IEC ESD protection make it appropriate for industrial, embedded, test, and legacy-adapter RS-232 ports. MAX3232EIDBR is a confirmed same-package alternative when its orderable packing method and remaining production requirements match the design. MAX3232EIDR is another same-footprint option, but its temperature grade and packing configuration should be checked before use. Neither same-package alternative should be released solely because the 16-SSOP outline matches: verify terminal assignments, ordering codes, lifecycle status, ESD ratings, and the manufacturer’s latest datasheet.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto MAX3232EIDBR MAX3232EIDR
Package 16-SSOP (0.209, 5.30mm Width) 16-SSOP - same package 16-SSOP - same package
Brand Texas Instruments Texas Instruments Texas Instruments
Product Type RS-232 line driver/receiver RS-232 line driver/receiver RS-232 line driver/receiver
Number of Drivers/Receivers 2/2 2/2 2/2
Supply Voltage 3 V to 5.5 V 3 V to 5.5 V 3 V to 5.5 V
Interface Standard RS-232 RS-232 RS-232
ESD Protection ±15 kV ±15 kV ±15 kV

Pangunahing mga Pagkakaiba

  • Identified 16-SSOP drop-in path without a PCB footprint change (kumpara saMAX3232EIDBR)
  • Extended-temperature RS-232 interface for industrial-oriented equipment (kumpara saMAX3232EIDR)
  • Two-channel interface with integrated bus-pin protection (kumpara saMAX3232EIDBR)

Talaan ng Disenyo

Place the charge-pump and bypass capacitors exactly as shown in the manufacturer datasheet, with short traces and the capacitor terminals nearest their associated IC pins. Keep the RS-232 driver outputs and receiver inputs away from switching nodes and sensitive analog inputs. Because MAX3232EIDBE4 includes ±15 kV IEC ESD protection, it still requires a controlled connector and return path; the IC protection is not a substitute for enclosure-level surge and ESD design.

Do not infer pin functions from the 2/2 channel count alone. Use the 16-SSOP pin-description table to identify the exact driver outputs, receiver inputs, charge-pump nodes, enable functions, supply pins, and grounds. Also check that the direction-control logic does not leave two RS-232 drivers actively driving the same bus. These checks are especially important when replacing MAX3232EIDBE4 with a different orderable suffix.

Decouple the MAX3232EIDBE4 supply locally and follow the manufacturer’s capacitance and placement recommendations. The device operates from 3 V to 5.5 V, but acceptable supply voltage does not remove the need for low-impedance bypass paths, especially when charge-pump current transitions can affect nearby circuitry. Validate startup, supply droop, and logic-level compatibility on the assembled board rather than inferring performance from nominal voltage alone.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Walang Lead
Yes
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

The product listing identifies MAX3232EIDBE4 as lead free and references IEC 61000-4-2 ESD testing. RoHS, REACH, AEC-Q100, halogen-free, and conflict-minerals status require confirmation from the current manufacturer documentation.

Data napatotohanan sa: 2026-11-09 — impormasyon na pinatunayan at pinapatakbo ng pangkat ng engineering ng XAIPART's component engineering team

Kaugnay na Hanapin

MAX3232EIDBE4 datasheet MAX3232EIDBE4 pinout MAX3232EIDBE4 datasheet pdf MAX3232EIDBE4 equivalent MAX3232EIDBE4 replacement MAX3232EIDBE4 cross reference MAX3232EIDBE4 vs MAX3232EIDBR MAX3232EIDBE4 16-SSOP footprint MAX3232EIDBE4 RS-232 transceiver MAX3232EIDBE4 industrial application Texas Instruments MAX3232EIDBE4 MAX3232EIDBE4 price MAX3232EIDBE4 stock MAX3232EIDBE4 schematic MAX3232EIDBE4 application circuit

Mga kaugnay na Mga Komponente at mga Tuntunin

Texas Instruments MAX3232EIDBE4 MAX3232EIDBR MAX3232EIDR MAX3232E RS-232 RS-232 transceiver line driver line receiver interface IC semiconductor charge pump ESD protection IEC 61000-4-2 UART 3.3 V logic 5 V logic 16-SSOP SSOP family surface mount industrial control test and measurement point-of-sale terminal embedded serial console
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ