MAX3232EIDBE4 - 3-5.5V 2/2 RS-232 Transceiver | Texas Instruments
MPN: MAX3232EIDBE4 ✓ Hoạt độngMAX3232EIDBE4 Tóm tắt
An RS-232 transceiver is an interface IC that combines differential signal generation and reception for serial communications. It belongs to the line-driver/receiver hierarchy within interface ICs, bridging a host UART or processor logic-level port and a wired RS-232 connection. The MAX3232EIDBE4 is intended for designs that need both transmit and receive functions on one compact, surface-mount device.
Key features include a 3 V to 5.5 V supply range, a 2/2 driver-and-receiver configuration, and bus-pin ESD protection rated to ±15 kV using the IEC 61000-4-2 contact-discharge and air-gap-discharge protection referenced in the product description. The 16-SSOP package measures approximately 5.30 mm in width and 0.209 inch in body width. The part is packaged in a tube according to the product listing.
The E designation identifies the enhanced MAX3232E family, which Texas Instruments describes as an improved direct drop-in replacement for the original MAX3232. Its integrated charge-pump circuitry supports level translation between low-voltage digital logic and RS-232 signal levels without requiring a separate ±12 V supply. This simplifies interface implementation while retaining the voltage ranges and peripheral arrangement expected in MAX3232-class designs.
Typical applications include RS-232 connections between embedded controllers and test equipment, industrial serial consoles, point-of-sale terminals, instrumentation, and legacy peripheral adapters. The two-driver and two-receiver arrangement supports full-duplex point-to-point links, provided the system designer accounts for the directional nature of each channel and applies appropriate interface protection where cables leave an enclosure.
When designing a board around the MAX3232EIDBE4, preserve the manufacturer-recommended charge-pump capacitor connections and place the associated ceramic capacitors close to their pins. Confirm that the external connector, cable, and grounding strategy match the intended RS-232 application, because the integrated IC protects its bus pins but cannot compensate for an inadequate enclosure or cable shield.
This page combines the device specifications, verified source links, package identification, application guidance, and confirmed same-package alternatives needed to evaluate the MAX3232EIDBE4. It also highlights where a replacement can be used without changing the 16-SSOP land pattern and where temperature, packing, or parameter differences still require engineering review.
Bộ thay thế dễ dàng lắp đặt cho MAX3232EIDBE4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
MAX3232EIDBR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3232EIDR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →MAX3232EIDBE4 Thông số kỹ thuật
| Product Type | Multichannel RS-232 line driver/receiver |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Transceiver Configuration | 2/2 |
| Supply Voltage Range | 3 V to 5.5 V |
| Interface Standard | RS-232 |
| ESD Protection | ±15 kV |
| ESD Test Method | IEC 61000-4-2 contact discharge and air-gap discharge |
| Hộp | 16-SSOP (0.209 inch, 5.30 mm width) |
| Packaging | Tube |
| Khoảng nhiệt độ hoạt động | −40°C to +85°C |
| Kiểu lắp đặt | Surface mount |
| Lead-Free Status | Lead free |
Hướng dẫn cấu hình chân MAX3232EIDBE4 16-ssop (0.209 inch, 5.30 mm width)
Cấu hình chân cho MAX3232EIDBE4 (16-ssop (0.209 inch, 5.30 mm width) gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho MAX3232EIDBE4.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
MAX3232EIDBE4 phù hợp cho 6 Áp dụngs: Industrial RS-232 Control Port, Embedded Serial Console, Test and Measurement Instrument, Point-of-Sale Terminal Interface, RS-232-to-Industrial Peripheral Link, Legacy Peripheral Adapter.
Industrial RS-232 Control Port
The MAX3232EIDBE4 fits an industrial controller that must communicate through a legacy RS-232 port while operating from a 3.3 V or 5 V logic rail. Its two drivers and two receivers support a full-duplex point-to-point connection, and the −40°C to +85°C operating range suits equipment expected to operate across industrial temperature conditions. Place the device between the host UART and the DE/RE-controlled transceiver direction logic, then follow the manufacturer charge-pump capacitor layout. The documented ±15 kV IEC ESD protection is valuable at the IC bus pins, although the finished enclosure must provide the primary mechanical protection for field-wired connectors.
Được đề xuất
Embedded Serial Console
An embedded Linux controller or microcontroller platform can use the MAX3232EIDBE4 to expose a service console through RS-232. The device accepts a 3 V to 5.5 V supply and includes both transmit and receive channels, allowing the host UART to exchange commands and diagnostic data with a PC or service terminal. The 16-SSOP package supports compact board layouts, while integrated ESD protection adds resilience to the transceiver interface. Maintain short signal traces, use the specified charge-pump capacitors, and isolate the logic ground and cable return correctly to avoid interpreting ground offsets as data errors.
Được đề xuất
Test and Measurement Instrument
The MAX3232EIDBE4 is useful in test and measurement instruments that communicate with a host PC, printer, or calibration system through RS-232. Two drivers and two receivers provide the channels required for a bidirectional instrument link, and the 3 V to 5.5 V supply range supports both 3.3 V and 5 V instrument architectures. The extended −40°C to +85°C range can serve laboratory-adjacent equipment with wider environmental requirements. Confirm the UART baud-rate support, logic thresholds, and timing limits from the manufacturer datasheet, and route the external connector through a layout that minimizes exposed copper and provides a controlled return path.
Được đề xuất
Point-of-Sale Terminal Interface
A point-of-sale terminal can use the MAX3232EIDBE4 when a receipt printer, customer display, or service accessory still relies on RS-232. The dual-driver, dual-receiver arrangement supports the bidirectional signal paths commonly found in point-of-sale equipment, and the 5.5 V upper supply limit accommodates established 5 V control systems. The integrated ±15 kV IEC ESD protection is especially relevant when accessories connect through external cables. The IC does not make a poorly grounded cable reliable, however, so use appropriate shielding, connector selection, and chassis grounding. Confirm the host UART logic levels and directional-control sequence before finalizing the schematic.
Được đề xuất
RS-232-to-Industrial Peripheral Link
The MAX3232EIDBE4 can bridge a low-voltage controller and an RS-232-equipped industrial peripheral such as a drive interface, programmable instrument, or legacy controller. Its two channels provide separate transmit and receive paths, while the 3 V to 5.5 V supply supports modern embedded logic without a separate bipolar power rail. The −40°C to +85°C range supports equipment intended for extended industrial environments. Apply the manufacturer’s capacitor placement rules, avoid long unprotected branches where possible, and verify that the peripheral’s driver and receiver definitions agree with the MAX3232E channel orientation. Cable transients and ground offsets must be handled at the system interface.
Được đề xuất
Legacy Peripheral Adapter
A compact legacy-peripheral adapter can be built around the MAX3232EIDBE4 when an existing RS-232 device must connect to a modern USB-to-serial or embedded controller. The transceiver provides two RS-232 drivers and two receivers while operating from the same 3.3 V or 5 V domain used by many compact adapters. The 16-SSOP package helps limit board area, and integrated bus-pin ESD protection improves interface robustness. Design the adapter so that direction-control lines have defined states during reset, keep the RS-232 side away from sensitive analog circuitry, and confirm the adapter connector’s pin assignment. Validate the completed cable assembly for ground-offset and ESD requirements.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho MAX3232EIDBE4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | MAX3232EIDBR | MAX3232EIDR |
|---|---|---|---|
| Package | 16-SSOP (0.209, 5.30mm Width) | 16-SSOP - same package | 16-SSOP - same package |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Product Type | RS-232 line driver/receiver | RS-232 line driver/receiver | RS-232 line driver/receiver |
| Number of Drivers/Receivers | 2/2 | 2/2 | 2/2 |
| Supply Voltage | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V |
| Interface Standard | RS-232 | RS-232 | RS-232 |
| ESD Protection | ±15 kV | ±15 kV | ±15 kV |
Bảo phân biệt quan trọng
- Identified 16-SSOP drop-in path without a PCB footprint change (vsMAX3232EIDBR)
- Extended-temperature RS-232 interface for industrial-oriented equipment (vsMAX3232EIDR)
- Two-channel interface with integrated bus-pin protection (vsMAX3232EIDBR)
Ghi chú thiết kế
Place the charge-pump and bypass capacitors exactly as shown in the manufacturer datasheet, with short traces and the capacitor terminals nearest their associated IC pins. Keep the RS-232 driver outputs and receiver inputs away from switching nodes and sensitive analog inputs. Because MAX3232EIDBE4 includes ±15 kV IEC ESD protection, it still requires a controlled connector and return path; the IC protection is not a substitute for enclosure-level surge and ESD design.
Do not infer pin functions from the 2/2 channel count alone. Use the 16-SSOP pin-description table to identify the exact driver outputs, receiver inputs, charge-pump nodes, enable functions, supply pins, and grounds. Also check that the direction-control logic does not leave two RS-232 drivers actively driving the same bus. These checks are especially important when replacing MAX3232EIDBE4 with a different orderable suffix.
Decouple the MAX3232EIDBE4 supply locally and follow the manufacturer’s capacitance and placement recommendations. The device operates from 3 V to 5.5 V, but acceptable supply voltage does not remove the need for low-impedance bypass paths, especially when charge-pump current transitions can affect nearby circuitry. Validate startup, supply droop, and logic-level compatibility on the assembled board rather than inferring performance from nominal voltage alone.
Thông tin tuân thủ
The product listing identifies MAX3232EIDBE4 as lead free and references IEC 61000-4-2 ESD testing. RoHS, REACH, AEC-Q100, halogen-free, and conflict-minerals status require confirmation from the current manufacturer documentation.