MC3486NG4 - Quad Differential Line Receiver | Texas Instruments
MPN: MC3486NG4 ✗ Tapus ng BuhayMC3486NG4 Ulas
A differential line receiver is an interface integrated circuit that converts a pair of complementary voltage signals into a single-ended logic-level output. This class of receiver belongs to the interface IC hierarchy, where physical-layer signal conditioning sits between external wiring and digital control logic. Differential reception improves noise immunity by comparing the voltage difference between two conductors rather than relying on one conductor referenced only to ground.
The MC3486 provides four complete receiver channels in one package. Its differential inputs support the electrical characteristics associated with TIA/EIA-422-B and TIA/EIA-423-B interfaces, as well as ITU Recommendations V.10 and V.11. TTL-compatible outputs simplify connection to microcontrollers, programmable logic controllers, counters, and other digital systems. Three-state outputs provide a high-impedance condition that can isolate an inactive channel during shared-bus operation.
The monolithic implementation gives each receiver an independent signal path while reducing the number of components required on a multi-channel interface card. Operating from one 5 V supply also simplifies system power distribution. The device is particularly suited to RS-422 and RS-423 point-to-point or multidrop arrangements where four balanced channels must be terminated and converted into logic signals.
Typical uses include factory automation controllers, industrial data acquisition systems, remote instrumentation, process-control equipment, and communications interfaces. Because the receiver converts external cable signals into digital logic levels, board-level termination, grounding, and routing remain important for dependable operation in electrically noisy environments.
Designers should follow the manufacturer datasheet for enable polarity, receiver input handling, supply requirements, and operating limits. Place input and enable traces away from high-current switching paths, use the recommended receiver network, and maintain a low-impedance ground reference between the interface board and its external equipment.
This page combines the manufacturer interface description, package information, practical RS-422 and RS-423 design guidance, compatible-product links, and an engineering-focused comparison of identified same-family receiver options.
Mga alternatibo na pwedeng ilagay na MC3486NG4 — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok MC3486NG4 (parehas na form factor at footprint) — pagkakaiba sa Package, Output State, Supported Standards.
MC3486N
✅ Drop-In ⚠️ Mga Talaan Hindi NaiwerikmoMagkontak para sa presyo
Tingnan ang Datasheet →MC3486NE4
✅ Drop-In ⚠️ Mga Talaan Hindi NaiwerikmoMagkontak para sa presyo
Tingnan ang Datasheet →MC3486NG4 Mga Spesipikasyon
| Product Type | Quadruple differential line receiver |
| Number of Receiver Channels | 4 channels |
| Volte ng Pagbibigay | 5 V |
| Output Logic Compatibility | TTL-compatible |
| Output State | 3-state, including high-impedance state |
| Supported Standards | ANSI TIA/EIA-422-B and ANSI TIA/EIA-423-B |
| ITU Interface Recommendations | ITU V.10 and ITU V.11 |
| Packhaging | 16-DIP (0.300 in, 7.62 mm) |
| Bilang ng Pin | 16 pins |
| Uri ng Pagpapasok | Through-hole |
| Number of Differential Inputs | 8 differential input terminals |
| Recommended Driver Companion | MC3487 quadruple differential line driver |
Gabay sa Pin Configuration ng MC3486NG4 16-dip (0.300 in, 7.62 mm)
Pin configuration para sa MC3486NG4 (16-dip (0.300 in, 7.62 mm) package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa MC3486NG4.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
MC3486NG4 ay nararapat para sa 6 aplikasyons: Factory Automation Controllers, Industrial Data Acquisition, Process-Control Equipment, Remote Instrumentation, Industrial Communication Interfaces, Legacy Equipment Upgrade.
Factory Automation Controllers
The MC3486NG4 fits factory automation controllers that must convert several balanced field-bus or equipment links into TTL-compatible logic. Four independent differential receivers provide a consolidated interface to motion controllers, sensor concentrators, and programmable logic control panels without requiring four separate receiver packages. Its single 5 V supply simplifies system power distribution, while three-state outputs allow inactive channels to be isolated when the host architecture uses shared digital resources. The manufacturer specifically identifies factory automation and control as a target application.
Inirekomenda
Industrial Data Acquisition
The MC3486NG4 is suitable for multi-channel industrial data-acquisition equipment receiving differential signals from remote sensors, counters, and test fixtures. Its four differential inputs help reduce susceptibility to noise by evaluating voltage differences between paired conductors. TTL-compatible outputs can feed counters, processors, or data-logging circuitry after level translation where required. The 16-pin DIP package also supports through-hole industrial controller layouts, and the three-state outputs provide useful bus-isolation flexibility.
Inirekomenda
Process-Control Equipment
The MC3486NG4 can form the balanced communications interface in process-control equipment that exchanges command and status information with remote field devices. Four independent receivers allow one controller to service multiple differential channels while maintaining a common 5 V supply. TIA/EIA-422-B and TIA/EIA-423-B support provides a defined basis for industrial point-to-point and multidrop signaling. The receiver's TTL-compatible outputs simplify connection to embedded control logic.
Inirekomenda
Remote Instrumentation
The MC3486NG4 is appropriate for remote instrumentation links where cable-borne differential signals must be recovered before measurement or control circuitry evaluates them. Four channels in one package can reduce board count compared with four single-receiver devices. The receiver architecture supports the noise-immunity benefits of differential signaling, while the TTL-compatible output makes the recovered information available to digital instrumentation. Proper grounding and input termination remain essential when long cables enter the enclosure.
Inirekomenda
Industrial Communication Interfaces
The MC3486NG4 supports industrial communication interfaces that terminate balanced RS-422 or RS-423 connections and present logic-level data to a host controller. Four channels can correspond to separate command, status, or diagnostic paths. According to the manufacturer datasheet, the device is intended to work with the MC3487 quadruple differential line driver, creating a complementary transmit-and-receive architecture. The common 5 V supply and through-hole package simplify integration into established industrial interface cards.
Inirekomenda
Legacy Equipment Upgrade
The MC3486NG4 is useful for maintenance and upgrade projects involving legacy equipment that uses a 16-pin DIP receiver board. Its through-hole package and four-channel organization support repair stocks and controlled PCB redesigns without changing the mechanical footprint. The three-state outputs allow retrofit designs to preserve shared-bus behavior, while TTL-compatible outputs can operate with legacy logic levels. Before replacement, confirm the board's enable polarity, termination arrangement, grounding, and suffix-specific operating requirements.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for MC3486NG4 — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | MC3486N | MC3486NE4 |
|---|---|---|---|
| Package | 16-DIP (0.300 in, 7.62 mm) | 16-DIP (0.300 in, 7.62 mm) | 16-DIP (0.300 in, 7.62 mm) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Receiver Channels | 4 differential receivers | 4 differential receivers | 4 differential receivers |
| Supply Voltage | 5 V | 5 V | 5 V |
| Output Compatibility | TTL-compatible | TTL-compatible | TTL-compatible |
| Output State | 3-state with high-impedance state | 3-state with high-impedance state | 3-state with high-impedance state |
| Interface Standards | TIA/EIA-422-B, TIA/EIA-423-B, ITU V.10 and V.11 | TIA/EIA-422-B, TIA/EIA-423-B, ITU V.10 and V.11 | TIA/EIA-422-B, TIA/EIA-423-B, ITU V.10 and V.11 |
| Recommended Driver Companion | MC3487 | MC3487 | MC3487 |
| Mounting Style | Through-hole | Through-hole | Through-hole |
Pangunahing mga Pagkakaiba
- Four differential receiver channels in one package (kumpara saMC3486N)
- Three-state outputs support shared-bus isolation (kumpara saMC3486NE4)
- Single 5 V architecture with TTL-compatible outputs (kumpara saMC3486N)
Talaan ng Disenyo
Route each differential input as a closely spaced pair and keep the pair away from switching nodes, relay contacts, high-current edges, and other noisy conductors. Maintain a continuous ground reference beneath the interface section. The receiver detects the difference between paired inputs, but poor pair geometry, unequal impedance, or ground discontinuity can still reduce noise rejection and make the installed system sensitive to cabling and grounding details.
Do not infer the enable polarity, common-mode limits, or termination method from generic RS-422 knowledge. Check the pin-description table and typical application circuit in the MC3486 manufacturer datasheet. Verify the external receiver network, enable state during reset, and termination arrangement on every channel. A wrong enable polarity or an inappropriate termination network can leave outputs in an unexpected state or distort the differential signal.
Decouple the single 5 V supply close to the device using the capacitance and layout specified by the manufacturer datasheet. Keep high-current return paths out of the receiver ground region and provide a low-impedance connection between the interface board and its external source. Although the MC3486 is not being evaluated here for SOA, stable supply voltage and low return-path impedance remain essential for consistent receiver thresholds and noise immunity.
For long or externally routed cables, use the manufacturer's recommended receiver termination and protect exposed interfaces against ESD and other transients. Shielding and grounding should follow the system-level cable strategy rather than be improvised at the receiver pins. Validate the completed board with the intended cable, connectors, and surrounding switching equipment because package-level compliance alone does not establish system-level EMC performance.
Impormasyon ng Pagsunod sa Kautusan
The interface IC is not a power semiconductor, so AEC-Q100 qualification is not applicable. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer product documentation or declaration.