MC3486NG4 - Quad Differential Line Receiver | Texas Instruments
MPN: MC3486NG4 ✗ Son Kullanım ZamanıMC3486NG4 Genel Bakış
A differential line receiver is an interface integrated circuit that converts a pair of complementary voltage signals into a single-ended logic-level output. This class of receiver belongs to the interface IC hierarchy, where physical-layer signal conditioning sits between external wiring and digital control logic. Differential reception improves noise immunity by comparing the voltage difference between two conductors rather than relying on one conductor referenced only to ground.
The MC3486 provides four complete receiver channels in one package. Its differential inputs support the electrical characteristics associated with TIA/EIA-422-B and TIA/EIA-423-B interfaces, as well as ITU Recommendations V.10 and V.11. TTL-compatible outputs simplify connection to microcontrollers, programmable logic controllers, counters, and other digital systems. Three-state outputs provide a high-impedance condition that can isolate an inactive channel during shared-bus operation.
The monolithic implementation gives each receiver an independent signal path while reducing the number of components required on a multi-channel interface card. Operating from one 5 V supply also simplifies system power distribution. The device is particularly suited to RS-422 and RS-423 point-to-point or multidrop arrangements where four balanced channels must be terminated and converted into logic signals.
Typical uses include factory automation controllers, industrial data acquisition systems, remote instrumentation, process-control equipment, and communications interfaces. Because the receiver converts external cable signals into digital logic levels, board-level termination, grounding, and routing remain important for dependable operation in electrically noisy environments.
Designers should follow the manufacturer datasheet for enable polarity, receiver input handling, supply requirements, and operating limits. Place input and enable traces away from high-current switching paths, use the recommended receiver network, and maintain a low-impedance ground reference between the interface board and its external equipment.
This page combines the manufacturer interface description, package information, practical RS-422 and RS-423 design guidance, compatible-product links, and an engineering-focused comparison of identified same-family receiver options.
Drop-in alternatifler için MC3486NG4 — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller MC3486NG4 (aynı form faktörü ve ayağa oturma) — farklı olan Package, Output State, Supported Standards.
MC3486N
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →MC3486NE4
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →MC3486NG4 Özellikler
| Product Type | Quadruple differential line receiver |
| Number of Receiver Channels | 4 channels |
| Besleme Gerilimi | 5 V |
| Output Logic Compatibility | TTL-compatible |
| Output State | 3-state, including high-impedance state |
| Supported Standards | ANSI TIA/EIA-422-B and ANSI TIA/EIA-423-B |
| ITU Interface Recommendations | ITU V.10 and ITU V.11 |
| Paket | 16-DIP (0.300 in, 7.62 mm) |
| Pin Sayısı | 16 pins |
| Montaj Türü | Through-hole |
| Number of Differential Inputs | 8 differential input terminals |
| Recommended Driver Companion | MC3487 quadruple differential line driver |
MC3486NG4 16-dip (0.300 in, 7.62 mm) Pin Yapısı Kılavuzu
MC3486NG4 (16-dip (0.300 in, 7.62 mm) paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.
Ayrıntılı pin çıkış verisi mevcut değil: MC3486NG4.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
MC3486NG4 için uygundur 6 uygulamas: Factory Automation Controllers, Industrial Data Acquisition, Process-Control Equipment, Remote Instrumentation, Industrial Communication Interfaces, Legacy Equipment Upgrade.
Factory Automation Controllers
The MC3486NG4 fits factory automation controllers that must convert several balanced field-bus or equipment links into TTL-compatible logic. Four independent differential receivers provide a consolidated interface to motion controllers, sensor concentrators, and programmable logic control panels without requiring four separate receiver packages. Its single 5 V supply simplifies system power distribution, while three-state outputs allow inactive channels to be isolated when the host architecture uses shared digital resources. The manufacturer specifically identifies factory automation and control as a target application.
Önerilen
Industrial Data Acquisition
The MC3486NG4 is suitable for multi-channel industrial data-acquisition equipment receiving differential signals from remote sensors, counters, and test fixtures. Its four differential inputs help reduce susceptibility to noise by evaluating voltage differences between paired conductors. TTL-compatible outputs can feed counters, processors, or data-logging circuitry after level translation where required. The 16-pin DIP package also supports through-hole industrial controller layouts, and the three-state outputs provide useful bus-isolation flexibility.
Önerilen
Process-Control Equipment
The MC3486NG4 can form the balanced communications interface in process-control equipment that exchanges command and status information with remote field devices. Four independent receivers allow one controller to service multiple differential channels while maintaining a common 5 V supply. TIA/EIA-422-B and TIA/EIA-423-B support provides a defined basis for industrial point-to-point and multidrop signaling. The receiver's TTL-compatible outputs simplify connection to embedded control logic.
Önerilen
Remote Instrumentation
The MC3486NG4 is appropriate for remote instrumentation links where cable-borne differential signals must be recovered before measurement or control circuitry evaluates them. Four channels in one package can reduce board count compared with four single-receiver devices. The receiver architecture supports the noise-immunity benefits of differential signaling, while the TTL-compatible output makes the recovered information available to digital instrumentation. Proper grounding and input termination remain essential when long cables enter the enclosure.
Önerilen
Industrial Communication Interfaces
The MC3486NG4 supports industrial communication interfaces that terminate balanced RS-422 or RS-423 connections and present logic-level data to a host controller. Four channels can correspond to separate command, status, or diagnostic paths. According to the manufacturer datasheet, the device is intended to work with the MC3487 quadruple differential line driver, creating a complementary transmit-and-receive architecture. The common 5 V supply and through-hole package simplify integration into established industrial interface cards.
Önerilen
Legacy Equipment Upgrade
The MC3486NG4 is useful for maintenance and upgrade projects involving legacy equipment that uses a 16-pin DIP receiver board. Its through-hole package and four-channel organization support repair stocks and controlled PCB redesigns without changing the mechanical footprint. The three-state outputs allow retrofit designs to preserve shared-bus behavior, while TTL-compatible outputs can operate with legacy logic levels. Before replacement, confirm the board's enable polarity, termination arrangement, grounding, and suffix-specific operating requirements.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: MC3486NG4 — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | MC3486N | MC3486NE4 |
|---|---|---|---|
| Package | 16-DIP (0.300 in, 7.62 mm) | 16-DIP (0.300 in, 7.62 mm) | 16-DIP (0.300 in, 7.62 mm) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Receiver Channels | 4 differential receivers | 4 differential receivers | 4 differential receivers |
| Supply Voltage | 5 V | 5 V | 5 V |
| Output Compatibility | TTL-compatible | TTL-compatible | TTL-compatible |
| Output State | 3-state with high-impedance state | 3-state with high-impedance state | 3-state with high-impedance state |
| Interface Standards | TIA/EIA-422-B, TIA/EIA-423-B, ITU V.10 and V.11 | TIA/EIA-422-B, TIA/EIA-423-B, ITU V.10 and V.11 | TIA/EIA-422-B, TIA/EIA-423-B, ITU V.10 and V.11 |
| Recommended Driver Companion | MC3487 | MC3487 | MC3487 |
| Mounting Style | Through-hole | Through-hole | Through-hole |
Ana Farklılayıcılar
- Four differential receiver channels in one package (karşılaştırma:MC3486N)
- Three-state outputs support shared-bus isolation (karşılaştırma:MC3486NE4)
- Single 5 V architecture with TTL-compatible outputs (karşılaştırma:MC3486N)
Tasarım Notları
Route each differential input as a closely spaced pair and keep the pair away from switching nodes, relay contacts, high-current edges, and other noisy conductors. Maintain a continuous ground reference beneath the interface section. The receiver detects the difference between paired inputs, but poor pair geometry, unequal impedance, or ground discontinuity can still reduce noise rejection and make the installed system sensitive to cabling and grounding details.
Do not infer the enable polarity, common-mode limits, or termination method from generic RS-422 knowledge. Check the pin-description table and typical application circuit in the MC3486 manufacturer datasheet. Verify the external receiver network, enable state during reset, and termination arrangement on every channel. A wrong enable polarity or an inappropriate termination network can leave outputs in an unexpected state or distort the differential signal.
Decouple the single 5 V supply close to the device using the capacitance and layout specified by the manufacturer datasheet. Keep high-current return paths out of the receiver ground region and provide a low-impedance connection between the interface board and its external source. Although the MC3486 is not being evaluated here for SOA, stable supply voltage and low return-path impedance remain essential for consistent receiver thresholds and noise immunity.
For long or externally routed cables, use the manufacturer's recommended receiver termination and protect exposed interfaces against ESD and other transients. Shielding and grounding should follow the system-level cable strategy rather than be improvised at the receiver pins. Validate the completed board with the intended cable, connectors, and surrounding switching equipment because package-level compliance alone does not establish system-level EMC performance.
Uyumluluk Bilgisi
The interface IC is not a power semiconductor, so AEC-Q100 qualification is not applicable. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer product documentation or declaration.