MC9S08QG8MFFE - 20MHz 8KB 8-Bit MCU | NXP Semiconductors
MPN: MC9S08QG8MFFE ✗ Tapus ng BuhayMC9S08QG8MFFE Ulas
An 8-bit microcontroller is a programmable controller built around a compact central processing unit, memory, and dedicated peripherals. Within the product hierarchy, the MC9S08QG8MFFE is an MCU, an embedded-processing device commonly used to monitor sensors, operate actuators, and sequence peripheral functions. Its S08 core, internal clocking capability, and 2.5 V or 3.3 V supply operation suit cost-sensitive battery-powered equipment.
The principal features include 20 MHz processing capability, 8 KB of Flash memory for program storage, and integration within a compact 5 x 5 mm QFN package with an exposed thermal pad. The family also supports an internal clock module with a frequency-locked loop, internal or external reference sources, 0.2% trim resolution, and approximately 2% deviation over temperature and voltage. These characteristics support deterministic timing in motor, appliance, and embedded control products.
The S08QG family uses an internal clock source module containing an FLL controlled by an internal or external reference. Precision trimming of the internal reference provides 0.2% resolution with 2% deviation over temperature and voltage. The manufacturer documentation states that the clock module supports bus frequencies from 1 MHz to 10 MHz, allowing designers to select an operating point suited to power consumption and processing requirements.
Typical applications include small appliance controls, battery-operated sensors, compact motor controllers, lighting equipment, and simple industrial interfaces. The exposed-pad package reduces assembly footprint while improving heat transfer on multilayer boards. Because the device is listed as end of life by NXP, design engineers should also evaluate a migration path before starting a new production design.
For new layouts, route the exposed pad to a grounded thermal and electrical land using the manufacturer package guidelines, and place bypass capacitors close to the supply pins. Confirm the exact pin multiplexing, clock configuration, memory organization, and programming requirements against the NXP datasheet before releasing firmware.
This page combines the manufacturer product information with distributor listings, lifecycle information, package details, application guidance, and honest sourcing considerations. It also identifies the limited availability of pin-compatible replacements so engineers can distinguish a true board-level substitution from a broader functional migration.
Mga alternatibo na pwedeng ilagay na MC9S08QG8MFFE — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok MC9S08QG8MFFE (parehas na form factor at footprint) — pagkakaiba sa Architecture, Mounting Type, Package, Package Type.
MC9S08QG8MPBE
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →MC9S08QG8CFFER
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
MC9S08QG8MDNE
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →MC9S08QG8MFFE Mga Pinakamataas na Rating at Electrical Characteristics
| Microcontroller Type | 8-bit MCU |
| Architecture | S08 core |
| Family | S08QG |
| Maximum CPU Frequency | 20 MHz |
| Flash Memory | 8 KB (8K x 8) |
| Program Memory Organization | 8K x 8 |
| Supply Voltage na Operasyon | 2.5 V / 3.3 V |
| Clock Source | Internal or external reference with FLL |
| FLL Bus Frequency Range | 1 MHz to 10 MHz |
| Internal Reference Trim Resolution | 0.2% |
| Internal Reference Deviation | 2% over temperature and voltage |
| Packhaging | 16-QFN-EP (5 x 5 mm) |
| Uri ng Pagpapasok | Surface mount |
| Thermal Pad | Exposed pad |
| Katayuan ng Lifecycle | End of Life |
Gabay sa Pin Configuration ng MC9S08QG8MFFE 16-qfn-ep (5 x 5 mm)
Pin configuration para sa MC9S08QG8MFFE (16-qfn-ep (5 x 5 mm) package). Kasama sa digital IC na ito ang GPIO, mga communication interface (UART, SPI, I2C), at mga power pin. Sumangguni sa datasheet ng manufacturer para sa mga alternatibong function ng pin at mga opsyon sa configuration. Mahalaga para sa disenyo ng embedded system at PCB layout.
Wala ng detalyadong pinout data na magagamit para sa MC9S08QG8MFFE.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
MC9S08QG8MFFE ay nararapat para sa 6 aplikasyons: Battery-Powered Sensor and Monitor, Small Appliance Control, Compact Motor and Actuator Control, LED Lighting Controller, Simple Industrial Interface Module, Legacy Product Maintenance and Spare Boards.
Battery-Powered Sensor and Monitor
The MC9S08QG8MFFE fits low-power sensing and monitoring products that sample a sensor, evaluate a threshold, and report a result through a serial interface. Its S08 core, 20 MHz maximum clock, 8 KB Flash program memory, and 2.5 V or 3.3 V operation suit compact battery-powered equipment. Use the FLL-based clock system to obtain a stable bus frequency from 1 MHz to 10 MHz, then disable unused peripherals and reduce the operating frequency when the sampling interval allows it to conserve energy.
Inirekomenda
Small Appliance Control
The MC9S08QG8MFFE is suitable for small appliance controllers that combine button inputs, motor or valve control, and a simple serial command interface. The 8-bit S08 architecture provides an economical solution when the control algorithm fits within 8 KB of Flash, while 2.5 V or 3.3 V operation simplifies mixed-voltage design. The 16-QFN exposed-pad package measures only 5 x 5 mm, allowing placement close to the power stage while the exposed pad improves thermal transfer to the board.
Inirekomenda
Compact Motor and Actuator Control
The MC9S08QG8MFFE can control simple motors, relays, solenoids, or actuators where deterministic sequencing and modest software complexity are required. Its 20 MHz S08 core supports interrupt-driven control routines, and the internal FLL allows the clock to be referenced to a controlled internal or external source. The 1 MHz to 10 MHz bus range provides a useful trade between response time and power use. Current ratings, flyback protection, and thermal conditions must be designed around the external load rather than the MCU itself.
Inirekomenda
LED Lighting Controller
The MC9S08QG8MFFE can serve as the logic controller in a small LED lighting module that accepts commands, applies effects, and drives external constant-current circuitry. Its 8 KB Flash capacity is appropriate for compact firmware with table-driven effects and communication routines, while the small 5 x 5 mm QFN footprint leaves board area for the power stage. Select the clock and unused-peripheral settings carefully because LED modules often operate from shared supplies where standby current contributes directly to energy consumption.
Inirekomenda
Simple Industrial Interface Module
The MC9S08QG8MFFE is appropriate for a compact industrial interface that converts switch states, sensor levels, or a serial command stream into a controlled output. The family provides serial-interface resources normally associated with higher-end controllers, and the 20 MHz S08 core offers enough performance for protocol handling without a high-power application processor. For factory or field equipment, validate reset behavior, clock tolerance, supply transients, and environmental requirements against the complete manufacturer data sheet.
Inirekomenda
Legacy Product Maintenance and Spare Boards
The MC9S08QG8MFFE remains useful for repairing or extending equipment built around the original S08QG8 design. Its defined 20 MHz clock rate, 8 KB Flash organization, and 16-QFN exposed-pad footprint allow an existing board to remain mechanically unchanged when a verified ordering variant is available. Because the manufacturer lists the device as end of life, request the exact suffix and date-code traceability, and verify the replacement's device identification and pin configuration before loading existing firmware.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for MC9S08QG8MFFE — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | MC9S08QG8MPBE | MC9S08QG8CFFER | MC9S08QG8MDNE |
|---|---|---|---|---|
| Package | 16-QFN-EP (5 x 5 mm) | 16-QFN-EP (5 x 5 mm) | 16-QFN-EP (5 x 5 mm) | 16-QFN-EP (5 x 5 mm) |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core Architecture | 8-bit S08 | 8-bit S08 | 8-bit S08 | 8-bit S08 |
| Maximum CPU Frequency | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| Flash Memory | 8 KB | 8 KB | 8 KB | 8 KB |
| Operating Supply Voltage | 2.5 V / 3.3 V | 2.5 V / 3.3 V | 2.5 V / 3.3 V | 2.5 V / 3.3 V |
| Clock Source | Internal or external reference with FLL | Internal or external reference with FLL | Internal or external reference with FLL | Internal or external reference with FLL |
| FLL Bus Frequency Range | 1 MHz to 10 MHz | 1 MHz to 10 MHz | 1 MHz to 10 MHz | 1 MHz to 10 MHz |
| Internal Reference Trim Resolution | 0.2% | 0.2% | 0.2% | 0.2% |
Pangunahing mga Pagkakaiba
- Maintains the original compact 16-QFN exposed-pad footprint (kumpara saMC9S08QG8CFQE)
- Provides the established S08QG8 software platform (kumpara saMC9S08QG8MPBE)
- Combines 20 MHz control with a low-power 8-bit architecture (kumpara saMC9S08QG8MDNE)
- Offers clock flexibility for compact embedded products (kumpara saMC9S08QG8CFFER)
Talaan ng Disenyo
Treat the exposed pad as both a thermal land and a low-impedance ground connection. Follow the NXP package land pattern for the 16-QFN device, place the pad on an inner or bottom copper plane where practical, and avoid thermal relief that can raise inductance. Place input bypass capacitors adjacent to the supply pins and route the exposed pad with short, wide traces to maximize heat dissipation.
Configure the internal clock and unused peripherals to match the product's average power budget. The S08QG clock module supports bus frequencies from 1 MHz to 10 MHz, so a lower operating point can reduce dynamic consumption when response-time requirements permit. Verify brownout and reset behavior, external load-switch arrangements, and supply-noise margins against the manufacturer electrical-characteristics table before production release.
Do not assume that every S08QG8 ordering suffix is a drop-in replacement. The MC9S08QG8CFQE listing includes an 8-pin NSOIC configuration, which requires a different footprint. For any MFF-series candidate, confirm the 16-QFN exposed-pad drawing, pin multiplexing, device ID, temperature grade, and clock settings. Existing firmware may also depend on reset-vector or peripheral-configuration differences that do not appear in a distributor comparison table.
Keep sensitive analog or timing-related routes away from switching-power nodes and high-current actuator traces. If an external crystal or precision reference is used, reserve the full oscillator footprint only after checking the selected ordering option and manufacturer guidance. Provide clean return paths beneath serial interfaces and keep the exposed pad away from sensitive routing where the package layout permits.
Impormasyon ng Pagsunod sa Kautusan
The manufacturer product page identifies the device as end of life, but the available product information does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations. Confirm compliance documentation for the exact orderable suffix before regulated production use.