MC9S08QG8MFFE - 20MHz 8KB 8-Bit MCU | NXP Semiconductors
MPN: MC9S08QG8MFFE ✗ اختتامِ زندگیMC9S08QG8MFFE جائزہ
An 8-bit microcontroller is a programmable controller built around a compact central processing unit, memory, and dedicated peripherals. Within the product hierarchy, the MC9S08QG8MFFE is an MCU, an embedded-processing device commonly used to monitor sensors, operate actuators, and sequence peripheral functions. Its S08 core, internal clocking capability, and 2.5 V or 3.3 V supply operation suit cost-sensitive battery-powered equipment.
The principal features include 20 MHz processing capability, 8 KB of Flash memory for program storage, and integration within a compact 5 x 5 mm QFN package with an exposed thermal pad. The family also supports an internal clock module with a frequency-locked loop, internal or external reference sources, 0.2% trim resolution, and approximately 2% deviation over temperature and voltage. These characteristics support deterministic timing in motor, appliance, and embedded control products.
The S08QG family uses an internal clock source module containing an FLL controlled by an internal or external reference. Precision trimming of the internal reference provides 0.2% resolution with 2% deviation over temperature and voltage. The manufacturer documentation states that the clock module supports bus frequencies from 1 MHz to 10 MHz, allowing designers to select an operating point suited to power consumption and processing requirements.
Typical applications include small appliance controls, battery-operated sensors, compact motor controllers, lighting equipment, and simple industrial interfaces. The exposed-pad package reduces assembly footprint while improving heat transfer on multilayer boards. Because the device is listed as end of life by NXP, design engineers should also evaluate a migration path before starting a new production design.
For new layouts, route the exposed pad to a grounded thermal and electrical land using the manufacturer package guidelines, and place bypass capacitors close to the supply pins. Confirm the exact pin multiplexing, clock configuration, memory organization, and programming requirements against the NXP datasheet before releasing firmware.
This page combines the manufacturer product information with distributor listings, lifecycle information, package details, application guidance, and honest sourcing considerations. It also identifies the limited availability of pin-compatible replacements so engineers can distinguish a true board-level substitution from a broader functional migration.
کے لیے ڈراپ اِن متبادل MC9S08QG8MFFE — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں MC9S08QG8MFFE (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Architecture, Mounting Type, Package, Package Type.
MC9S08QG8MPBE
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →MC9S08QG8CFFER
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MC9S08QG8MDNE
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →MC9S08QG8MFFE زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Microcontroller Type | 8-bit MCU |
| Architecture | S08 core |
| Family | S08QG |
| Maximum CPU Frequency | 20 MHz |
| Flash Memory | 8 KB (8K x 8) |
| Program Memory Organization | 8K x 8 |
| آپریٹنگ سپلائی وولٹیج | 2.5 V / 3.3 V |
| Clock Source | Internal or external reference with FLL |
| FLL Bus Frequency Range | 1 MHz to 10 MHz |
| Internal Reference Trim Resolution | 0.2% |
| Internal Reference Deviation | 2% over temperature and voltage |
| پیکیج | 16-QFN-EP (5 x 5 mm) |
| ماؤنٹنگ ٹائپ | Surface mount |
| Thermal Pad | Exposed pad |
| لائف سائیکل کی حالت | End of Life |
MC9S08QG8MFFE 16-qfn-ep (5 x 5 mm) پن کنفیگریشن گائیڈ
MC9S08QG8MFFE (16-qfn-ep (5 x 5 mm) پیکیج) کے لیے پن کنفیگریشن۔ اس ڈیجیٹل IC میں GPIO، کمیونیکیشن انٹرفیس (UART، SPI، I2C) اور پاور پنز شامل ہیں۔ متبادل پن فنکشنز اور کنفیگریشن آپشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ ایمبیڈڈ سسٹم ڈیزائن اور PCB لے آؤٹ کے لیے ضروری۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں MC9S08QG8MFFE.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
MC9S08QG8MFFE کے لیے موزوں ہے 6 ایپلیکیشنs: Battery-Powered Sensor and Monitor, Small Appliance Control, Compact Motor and Actuator Control, LED Lighting Controller, Simple Industrial Interface Module, Legacy Product Maintenance and Spare Boards.
Battery-Powered Sensor and Monitor
The MC9S08QG8MFFE fits low-power sensing and monitoring products that sample a sensor, evaluate a threshold, and report a result through a serial interface. Its S08 core, 20 MHz maximum clock, 8 KB Flash program memory, and 2.5 V or 3.3 V operation suit compact battery-powered equipment. Use the FLL-based clock system to obtain a stable bus frequency from 1 MHz to 10 MHz, then disable unused peripherals and reduce the operating frequency when the sampling interval allows it to conserve energy.
تجویز کردہ
Small Appliance Control
The MC9S08QG8MFFE is suitable for small appliance controllers that combine button inputs, motor or valve control, and a simple serial command interface. The 8-bit S08 architecture provides an economical solution when the control algorithm fits within 8 KB of Flash, while 2.5 V or 3.3 V operation simplifies mixed-voltage design. The 16-QFN exposed-pad package measures only 5 x 5 mm, allowing placement close to the power stage while the exposed pad improves thermal transfer to the board.
تجویز کردہ
Compact Motor and Actuator Control
The MC9S08QG8MFFE can control simple motors, relays, solenoids, or actuators where deterministic sequencing and modest software complexity are required. Its 20 MHz S08 core supports interrupt-driven control routines, and the internal FLL allows the clock to be referenced to a controlled internal or external source. The 1 MHz to 10 MHz bus range provides a useful trade between response time and power use. Current ratings, flyback protection, and thermal conditions must be designed around the external load rather than the MCU itself.
تجویز کردہ
LED Lighting Controller
The MC9S08QG8MFFE can serve as the logic controller in a small LED lighting module that accepts commands, applies effects, and drives external constant-current circuitry. Its 8 KB Flash capacity is appropriate for compact firmware with table-driven effects and communication routines, while the small 5 x 5 mm QFN footprint leaves board area for the power stage. Select the clock and unused-peripheral settings carefully because LED modules often operate from shared supplies where standby current contributes directly to energy consumption.
تجویز کردہ
Simple Industrial Interface Module
The MC9S08QG8MFFE is appropriate for a compact industrial interface that converts switch states, sensor levels, or a serial command stream into a controlled output. The family provides serial-interface resources normally associated with higher-end controllers, and the 20 MHz S08 core offers enough performance for protocol handling without a high-power application processor. For factory or field equipment, validate reset behavior, clock tolerance, supply transients, and environmental requirements against the complete manufacturer data sheet.
تجویز کردہ
Legacy Product Maintenance and Spare Boards
The MC9S08QG8MFFE remains useful for repairing or extending equipment built around the original S08QG8 design. Its defined 20 MHz clock rate, 8 KB Flash organization, and 16-QFN exposed-pad footprint allow an existing board to remain mechanically unchanged when a verified ordering variant is available. Because the manufacturer lists the device as end of life, request the exact suffix and date-code traceability, and verify the replacement's device identification and pin configuration before loading existing firmware.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا MC9S08QG8MFFE — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | MC9S08QG8MPBE | MC9S08QG8CFFER | MC9S08QG8MDNE |
|---|---|---|---|---|
| Package | 16-QFN-EP (5 x 5 mm) | 16-QFN-EP (5 x 5 mm) | 16-QFN-EP (5 x 5 mm) | 16-QFN-EP (5 x 5 mm) |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Core Architecture | 8-bit S08 | 8-bit S08 | 8-bit S08 | 8-bit S08 |
| Maximum CPU Frequency | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| Flash Memory | 8 KB | 8 KB | 8 KB | 8 KB |
| Operating Supply Voltage | 2.5 V / 3.3 V | 2.5 V / 3.3 V | 2.5 V / 3.3 V | 2.5 V / 3.3 V |
| Clock Source | Internal or external reference with FLL | Internal or external reference with FLL | Internal or external reference with FLL | Internal or external reference with FLL |
| FLL Bus Frequency Range | 1 MHz to 10 MHz | 1 MHz to 10 MHz | 1 MHz to 10 MHz | 1 MHz to 10 MHz |
| Internal Reference Trim Resolution | 0.2% | 0.2% | 0.2% | 0.2% |
اہم امتیازی خصوصیات
- Maintains the original compact 16-QFN exposed-pad footprint (بمقابلہMC9S08QG8CFQE)
- Provides the established S08QG8 software platform (بمقابلہMC9S08QG8MPBE)
- Combines 20 MHz control with a low-power 8-bit architecture (بمقابلہMC9S08QG8MDNE)
- Offers clock flexibility for compact embedded products (بمقابلہMC9S08QG8CFFER)
ڈیزائن نوٹس
Treat the exposed pad as both a thermal land and a low-impedance ground connection. Follow the NXP package land pattern for the 16-QFN device, place the pad on an inner or bottom copper plane where practical, and avoid thermal relief that can raise inductance. Place input bypass capacitors adjacent to the supply pins and route the exposed pad with short, wide traces to maximize heat dissipation.
Configure the internal clock and unused peripherals to match the product's average power budget. The S08QG clock module supports bus frequencies from 1 MHz to 10 MHz, so a lower operating point can reduce dynamic consumption when response-time requirements permit. Verify brownout and reset behavior, external load-switch arrangements, and supply-noise margins against the manufacturer electrical-characteristics table before production release.
Do not assume that every S08QG8 ordering suffix is a drop-in replacement. The MC9S08QG8CFQE listing includes an 8-pin NSOIC configuration, which requires a different footprint. For any MFF-series candidate, confirm the 16-QFN exposed-pad drawing, pin multiplexing, device ID, temperature grade, and clock settings. Existing firmware may also depend on reset-vector or peripheral-configuration differences that do not appear in a distributor comparison table.
Keep sensitive analog or timing-related routes away from switching-power nodes and high-current actuator traces. If an external crystal or precision reference is used, reserve the full oscillator footprint only after checking the selected ordering option and manufacturer guidance. Provide clean return paths beneath serial interfaces and keep the exposed pad away from sensitive routing where the package layout permits.
تعمیل کی معلومات
The manufacturer product page identifies the device as end of life, but the available product information does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations. Confirm compliance documentation for the exact orderable suffix before regulated production use.