Microchip Technology

MCP6141-E/P - 600 nA Low-Power RRIO Op Amp | Microchip Technology

MPN: MCP6141-E/P ✓ Nakahanda
1.4 V to 5.5 V Vdss 600 nA typical Id 8-pin PDIP Package
MOQ: 1 |

MCP6141-E/P Ulas

The Microchip Technology MCP6141-E/P is a single 600 nA quiescent-current operational amplifier with rail-to-rail input and rail-to-rail output operation over a 1.4 V to 5.5 V supply range. It is packaged in an 8-pin PDIP format and is specified for general-purpose low-power amplifier applications. The device is designed for battery-powered systems where low supply current and wide input/output swing are important. Its typical gain-bandwidth product is 100 kHz, making it appropriate for low-frequency signal conditioning rather than high-speed waveform processing.

An operational amplifier, or op amp, is an analog building block that uses high open-loop gain to amplify the difference between two input voltages. MCP6141 belongs to the non-unity-gain-stable amplifier family, so the minimum recommended closed-loop gain is 10 V/V. Its rail-to-rail input and output characteristics help maximize usable signal range on low-voltage supplies where conventional input and output stages would clip before the supply rails.

Key electrical characteristics include a typical quiescent current of 600 nA, a maximum quiescent current of 1 uA, a typical gain-bandwidth product of 100 kHz, and a typical input bias current of 5 nA. The operating voltage range is 1.4 V to 5.5 V, while the operating temperature range extends from -40 C to +125 C. These characteristics make the MCP6141 suitable for portable instrumentation, sensor interfaces, battery monitoring, medical-device signal conditioning, and low-power industrial controls.

The MCP6141’s low bias current reduces loading on high-impedance sensors, while rail-to-rail input operation improves usable dynamic range. The 100 kHz bandwidth supports accurate amplification of slow sensor signals and control-loop signals. Because the amplifier is non-unity-gain stable, feedback configurations should use a closed-loop gain of at least 10 V/V, and the output must remain within the supply rails.

Typical applications include low-frequency ECG and biomedical signal conditioning, portable sensor interfaces, battery-powered measurement systems, and low-current industrial sensing. Decoupling capacitors should be placed close to the supply pins, and the circuit should be checked for offset, noise, output-current, and capacitive-load limitations using the manufacturer’s typical application guidance.

This page consolidates the MCP6141’s operating characteristics, package information, drop-in alternatives, application guidance, and design notes for engineers evaluating low-power analog signal chains.

Mga alternatibo na pwedeng ilagay na MCP6141-E/P — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.

Variante sa Seri na ito

Katulad na modelo sa serye na katugma sa pagpasok MCP6141-E/P (parehas na form factor at footprint) — pagkakaiba sa Input Common-Mode Range, Slew Rate, Output Swing, Package, Amplifier Type.

Microchip Technology
Input Common-Mode Range: -0.3 V minimum to VDD + 0.3 V maximum
Slew Rate: 24,000 V/us
Amplifier Type: Single operational amplifier
Microchip Technology
Input Common-Mode Range: Rail-to-rail input
Slew Rate: 0.003 V/us
Output Swing: Rail-to-rail output

MCP6141-I/P

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
Microchip Technology
📦 8-pin PDIP
1 circuit · Single operational amplifier · 1.4 V to 5.5 V · 600 nA typical · 1 uA maximum · 100 kHz typical · 10 V/V · -0.3 V minimum to VDD + 0.3 V maximum

Magkontak para sa presyo

Tingnan ang Datasheet →

MCP6142-E/P

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
📦 8-pin PDIP
Dual-amplifier family member rather than a single amplifier; the same 8-pin PDIP family footprint is used, but channel count differs.

📋 Alternatibo na Reference (hindi sa katalogo)

MCP6142-I/P

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
Microchip Technology
📦 8-pin PDIP
General-purpose operational amplifier · 2 circuits · 1.4 V to 5.5 V · 600 nA per amplifier · 1 uA per amplifier · 100 kHz · Rail-to-rail input · Rail-to-rail output

Magkontak para sa presyo

Tingnan ang Datasheet →

MCP6143-E/P

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
📦 8-pin PDIP
Same MCP6141 family and 8-pin PDIP family package; channel configuration and exact feature set differ from the single MCP6141.

📋 Alternatibo na Reference (hindi sa katalogo)

MCP6143-I/P

✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo
📦 8-pin PDIP
Same MCP6141 family and 8-pin PDIP family package; industrial temperature suffix and channel configuration differ from MCP6141-E/P.

📋 Alternatibo na Reference (hindi sa katalogo)

MCP6141-E/P Mga Pinakamataas na Rating at Electrical Characteristics

Product Type Single operational amplifier
Supply Voltage Range 1.4 V to 5.5 V
Kuru-kuryente ng Kapayapaan 600 nA typical
Maximum Quiescent Current 1 uA maximum
Gain-Bandwidth Product 100 kHz typical
Input Bias Current 5 nA typical
Input Common-Mode Range Rail-to-rail
Output Swing Rail-to-rail
Minimum Stable Gain 10 V/V
CMRR 80 dB
Slew Rate 24000 V/us
Hanay ng Temperature na Operasyon -40 C to +125 C
Packhaging 8-pin PDIP
Uri ng Pagpapasok Through-hole

Gabay sa Pin Configuration ng MCP6141-E/P 8-pin pdip

Pin configuration para sa MCP6141-E/P (8-pin pdip package). Ang analog component na ito ay may input, output, at power supply pins. Sumangguni sa datasheet ng manufacturer para sa offset null, compensation, at enable pin configurations. Perpekto para sa signal conditioning at amplifier circuits.

Pinout diagram ng 8-pin pdip package para sa MCP6141-E/P

Wala ng detalyadong pinout data na magagamit para sa MCP6141-E/P.

Sumangguni sa datasheet para sa buong pin configuration.

Tipikal na mga Gamit

MCP6141-E/P ay nararapat para sa 6 aplikasyons: Battery-Powered Sensor Interfaces, Portable Biomedical Signal Conditioning, Low-Power Industrial Control Signals, Battery Voltage Monitoring, Portable Environmental Monitoring, Low-Power Instrumentation Buffering.

🧩

Battery-Powered Sensor Interfaces

The MCP6141-E/P fits low-power sensor front ends because its 1.4 V to 5.5 V supply range supports small battery-powered systems and its typical 600 nA quiescent current minimizes standby demand. The rail-to-rail input characteristic is useful when sensor output levels move close to either supply rail. Its typical 5 nA input bias current also reduces loading on high-impedance sensors. Use a closed-loop gain of at least 10 V/V and place the bypass capacitor close to the supply pins.

💊

Portable Biomedical Signal Conditioning

The MCP6141-E/P is suitable for low-level biomedical signal conditioning where low power and high input impedance are priorities. Its 5 nA typical input bias current minimizes source loading, while the rail-to-rail input and output stages make better use of the available 1.4 V to 5.5 V supply range. The 100 kHz typical gain-bandwidth product is appropriate for slow physiological signals rather than wideband diagnostic instrumentation. Medical systems must still meet their own electrical-safety and regulatory requirements.

🏭

Low-Power Industrial Control Signals

The MCP6141-E/P can amplify slow process-control signals in low-power industrial electronics because its 100 kHz typical gain-bandwidth product is sufficient for many sensor and control-loop signals. The low 600 nA typical quiescent current helps isolated or battery-backed monitoring modules consume less standby power. Its wide input range supports signals that approach the supply rails. Confirm the operating temperature requirement and use the manufacturer’s recommended grounding and layout practices.

⚡

Battery Voltage Monitoring

The MCP6141-E/P can serve as a low-power buffer or gain stage in a battery-voltage monitoring path. Rail-to-rail input and output behavior allows the circuit to operate with small headroom, while the 600 nA typical quiescent current limits the monitoring amplifier’s effect on battery life. The non-unity-gain-stable architecture requires a closed-loop gain of at least 10 V/V. The input network must also account for the amplifier’s input bias current and leakage.

🌐

Portable Environmental Monitoring

The MCP6141-E/P is appropriate for portable environmental-monitoring instruments that combine low-voltage sensors with long battery life. Its low input bias current helps preserve weak sensor signals, and the rail-to-rail input reduces the need for an artificial bias near mid-supply. The 100 kHz typical bandwidth is ample for temperature, humidity, gas, and environmental signals that vary slowly. Use local bypass capacitance and short feedback traces to preserve low-noise operation.

🔧

Low-Power Instrumentation Buffering

The MCP6141-E/P can be used in low-power instrumentation where a high-impedance source must drive a downstream measurement stage. Its 5 nA typical input bias current reduces loading, and its rail-to-rail input and output behavior support operation close to the supply limits. Because it is non-unity-gain stable, the circuit should use a gain of 10 V/V or higher rather than a unity-gain buffer configuration. Check offset, noise, and output-drive requirements against the manufacturer’s test conditions.

Buod ng mga Inirekomendang Produkto

MCP6142-I/P Microchip Technology Ginagamit sa: Battery-Powered Sensor Interfaces, Low-Power Industrial Control Signals, Portable Environmental Monitoring MCP6143-I/P Related MCP6141-family low-power amplifier Ginagamit sa: Battery-Powered Sensor Interfaces, Portable Environmental Monitoring MCP6142-E/P Dual low-power family option for paired signal channels Ginagamit sa: Portable Biomedical Signal Conditioning, Battery Voltage Monitoring, Low-Power Instrumentation Buffering MCP6141-I/P Microchip Technology Ginagamit sa: Portable Biomedical Signal Conditioning, Battery Voltage Monitoring, Low-Power Instrumentation Buffering MCP6143-E/P Related family member for additional low-power signal paths Ginagamit sa: Low-Power Industrial Control Signals
What is the MCP6141-E/P?
The MCP6141-E/P is a single, general-purpose operational amplifier from Microchip Technology with a typical quiescent current of 600 nA. According to the manufacturer product page, it supports rail-to-rail input and output operation from a 1.4 V to 5.5 V supply and has a typical gain-bandwidth product of 100 kHz. It is suited to battery-powered and low-leakage signal-conditioning designs.
What is the operating voltage of MCP6141-E/P?
The MCP6141-E/P operates from 1.4 V to 5.5 V. This low supply range allows operation from a single-cell or low-voltage battery source, while also supporting conventional low-voltage rails. The manufacturer’s MCP6141 product page identifies the 1.4 V to 5.5 V range, and the device datasheet describes operation with single supplies as low as 1.4 V.
What is the quiescent current of MCP6141-E/P?
The MCP6141-E/P has a typical quiescent current of 600 nA and a maximum quiescent current of 1 uA per amplifier. This low operating current reduces the load placed on a battery or low-power supply and makes the device useful for portable instrumentation and always-on sensing. The current rating is specified by Microchip Technology for the MCP6141 family.
Does MCP6141-E/P support rail-to-rail input and output?
Yes. The MCP6141-E/P supports rail-to-rail input and output operation. Rail-to-rail input behavior allows the input common-mode voltage to approach the supply limits, while rail-to-rail output operation increases the usable output-voltage range. These features are particularly useful in low-voltage systems where signal swing must be maximized.
What is the gain-bandwidth product of MCP6141-E/P?
The MCP6141-E/P has a typical gain-bandwidth product of 100 kHz. This bandwidth is suited to low-frequency sensor signals, measurement channels, and slowly changing control signals rather than high-speed video or communications paths. The manufacturer product page lists 100 kHz as the typical GBWP for MCP6141.
What is the minimum gain for MCP6141-E/P?
The MCP6141-E/P is non-unity-gain stable and is intended for closed-loop gains of 10 V/V or higher. Designers should avoid relying on voltage-follower operation or other near-unity-gain configurations. The minimum-gain requirement is important when selecting feedback values and when evaluating whether an alternative op amp can replace the MCP6141.
Where can I download the MCP6141-E/P datasheet?
The manufacturer datasheet PDF is available at the Microchip Technology URL recorded on this page. It describes the MCP6141/2/3/4 family, including the low-voltage supply range, rail-to-rail operation, quiescent current, gain stability, and electrical characteristics. Use the manufacturer document for pin assignments, recommended operating conditions, and application details.
Where can I find the MCP6141-E/P pinout?
The MCP6141-E/P pin assignment should be taken from the pin-description table in the Microchip Technology MCP6141 family datasheet. The component is identified in distributor listings as an 8-pin PDIP package. Use the package drawing and pin table together when assigning signal, supply, and feedback connections on the PCB.
What can replace MCP6141-E/P?
The closest same-family choices are the Microchip MCP6142-E/P and MCP6142-I/P, subject to confirming channel count and temperature-grade requirements. The MCP6141-E/P is a single amplifier in an 8-pin PDIP, while the MCP6142 family is dual-channel, so it is a functional same-package option rather than an unconditional functional replacement for every board.
Is MCP6141-I/P a drop-in replacement for MCP6141-E/P?
MCP6141-I/P is the same MCP6141 family and 8-pin PDIP configuration, making it a practical same-package replacement candidate. The main difference is the temperature grade: the -E/P suffix denotes the extended-temperature option, while -I/P denotes the industrial-temperature option. Confirm the required temperature range and purchasing availability before substituting it.
What is the difference between MCP6141-E/P and MCP6142-E/P?
The MCP6141-E/P contains one amplifier, while the MCP6142-E/P is a dual-amplifier family member in the same 8-pin PDIP family. Their low-power characteristics and voltage range are related, but a dual device cannot automatically replace a single-device footprint without checking the pinout, channel usage, and unused-channel configuration.
Is MCP6141-E/P suitable for battery-powered sensor interfaces?
Yes. The MCP6141-E/P is well suited to battery-powered sensor interfaces because its typical quiescent current is only 600 nA, its supply range begins at 1.4 V, and its input is rail-to-rail. These characteristics reduce supply consumption and improve signal range. High-impedance sensors also benefit from the typical 5 nA input bias current.
Can MCP6141-E/P be used for low-frequency medical signal conditioning?
The MCP6141-E/P can be used for low-frequency medical signal conditioning when the circuit stays within the device’s gain, bandwidth, input, output, and leakage limits. Its 100 kHz typical gain-bandwidth product and 5 nA typical input bias current are useful for low-level sensor amplification. Medical designs must also satisfy their own safety, isolation, and validation requirements.
How should decoupling and PCB layout be handled for MCP6141-E/P?
Place the supply bypass capacitor close to the MCP6141-E/P supply pins and route the supply and ground connections with low loop area. Keep input and feedback traces short, especially when the source impedance is high. The manufacturer datasheet’s recommended application circuit should be used as the starting point for grounding, decoupling, and output-load requirements.
Does MCP6141-E/P require a minimum load or gain configuration?
The MCP6141-E/P is non-unity-gain stable, so it should be operated at a closed-loop gain of 10 V/V or higher. It is not intended for unity-gain voltage-follower use. The exact recommended feedback network and output-load conditions should be taken from the manufacturer datasheet, and the gain requirement must be included in any replacement qualification.

Impormasyon ng Talumpati sa Engineering for MCP6141-E/P — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.

Paunawang Hanapin

Choose MCP6141-E/P when a single, low-power op amp is needed for a 1.4 V to 5.5 V design and the extended-temperature grade is appropriate. Its 600 nA typical quiescent current, rail-to-rail input/output behavior, and 100 kHz typical gain-bandwidth product are well matched to battery-powered sensors, portable instrumentation, and slow industrial signals. MCP6141-I/P is the closest same-family single-amplifier alternative when the industrial temperature grade is sufficient. MCP6142-E/P and MCP6142-I/P can be useful when a dual amplifier is preferred, but their channel count and unused-pin handling must be checked against the original circuit. MCP6143 variants should be selected only after confirming the required channel configuration and pin functions. All listed candidates use the same 8-pin PDIP family package, but they are not electrically interchangeable in every application.

Ikabit sa Mga Alternatibo

Parametro Ito ang Producto MCP6141-I/P MCP6142-E/P MCP6142-I/P MCP6143-E/P MCP6143-I/P
Package 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Supply Voltage Range 1.4 V to 5.5 V 1.4 V to 5.5 V 1.4 V to 5.5 V 1.4 V to 5.5 V 1.4 V to 5.5 V 1.4 V to 5.5 V
Gain-Bandwidth Product 100 kHz typical 100 kHz typical 100 kHz typical 100 kHz typical 100 kHz typical 100 kHz typical
Temperature Grade -E/P extended grade -I/P industrial grade -E/P extended grade -I/P industrial grade -E/P extended grade -I/P industrial grade
Input and Output Operation Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output

Pangunahing mga Pagkakaiba

  • Lower quiescent current than a typical general-purpose precision amplifier (kumpara saMCP6141-I/P)
  • Single-amplifier configuration preserves the simplest 8-pin PDIP implementation (kumpara saMCP6142-E/P)
  • Rail-to-rail input and output support low-voltage signal-chain headroom (kumpara saMCP6143-I/P)

Talaan ng Disenyo

Place the supply bypass capacitor immediately adjacent to the MCP6141-E/P supply and ground pins. Keep the input, output, and feedback traces short so that the amplifier’s very low 600 nA typical quiescent current does not have to compete with leakage through long PCB paths. Confirm that the selected bypass capacitor has acceptable voltage bias and leakage characteristics for the actual supply range.

Do not configure MCP6141-E/P as a unity-gain voltage follower. The device is non-unity-gain stable and should use a closed-loop gain of at least 10 V/V. This requirement must also be checked during replacement testing because a substitute with unity-gain stability may behave differently in the same feedback network.

For high-impedance sources, keep the op-amp input pins and feedback components away from long exposed traces, connectors, and switching nodes. Because the typical input bias current is only 5 nA, even small PCB leakage can affect a high-impedance sensor interface. Use a protective ground arrangement around the input where appropriate and verify the complete board’s leakage behavior.

Check the closed-loop bandwidth against the signal bandwidth and the 100 kHz typical gain-bandwidth product. A gain of 10 V/V leaves substantially less closed-loop bandwidth than the gain-bandwidth product, while higher gains can be useful for slow sensor signals. Avoid driving a large capacitive load directly from the output unless the load condition is supported by the manufacturer’s guidance.

Impormasyon ng Pagsunod sa Kautusan

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Walang Lead
Unknown
Walang Halogen
Unknown
Mga Conflict Mineral
Unknown

Compliance status was not stated in the manufacturer product-page or distributor snippets. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification requirements with the manufacturer before releasing a regulated design.

Data napatotohanan sa: 2026-11-10 — impormasyon na pinatunayan at pinapatakbo ng pangkat ng engineering ng XAIPART's component engineering team

Kaugnay na Hanapin

mcp6141 datasheet MCP6141-E/P datasheet MCP6141-E/P pinout MCP6141-E/P equivalent MCP6141-E/P replacement MCP6141-E/P price MCP6141-E/P stock MCP6141-E/P lead time MCP6141 600 nA op amp MCP6141 rail to rail amplifier MCP6141-E/P vs MCP6142-E/P MCP6141-E/P 8-pin PDIP MCP6141-E/P battery powered MCP6141-E/P application circuit What is the operating voltage of MCP6141-E/P?

Mga kaugnay na Mga Komponente at mga Tuntunin

Microchip Technology MCP6141-E/P MCP6141 MCP6142-E/P MCP6142-I/P MCP6143-E/P MCP6143-I/P Operational amplifier Op amp Analog IC Low-power amplifier Rail-to-rail input Rail-to-rail output Quiescent current Gain-bandwidth product GBWP Input bias current Non-unity-gain stable 8-pin PDIP DIP package Through-hole package Battery-powered electronics Sensor interface Portable instrumentation Low-voltage analog signal conditioning
Mabilis na Tanggap na RFQ
Ihanda ang buong detalye — ang aming pangkalakal na koponan ay tutugon sa loob ng 24 oras
Numero ng Parte Mga Tagagawa Pakete QTY Target na Halaga Pinalawak
✓
Quote na inilabas!

Ating tumugon sa iyong email sa loob ng 24 oras

1
RFQ Naisumite
2
Received na ang Kwaliksik
3
Nai-order
4
Pagbabayad
5
Inihanda
6
Naihanda
Tingnan ang Detalye ng RFQ