Microchip Technology

MCP6141-E/P - 600 nA Low-Power RRIO Op Amp | Microchip Technology

MPN: MCP6141-E/P ✓ 啟用中
1.4 V to 5.5 V Vdss 600 nA typical Id 8-pin PDIP Package
MOQ: 1 |

MCP6141-E/P 概覽

The Microchip Technology MCP6141-E/P is a single 600 nA quiescent-current operational amplifier with rail-to-rail input and rail-to-rail output operation over a 1.4 V to 5.5 V supply range. It is packaged in an 8-pin PDIP format and is specified for general-purpose low-power amplifier applications. The device is designed for battery-powered systems where low supply current and wide input/output swing are important. Its typical gain-bandwidth product is 100 kHz, making it appropriate for low-frequency signal conditioning rather than high-speed waveform processing.

An operational amplifier, or op amp, is an analog building block that uses high open-loop gain to amplify the difference between two input voltages. MCP6141 belongs to the non-unity-gain-stable amplifier family, so the minimum recommended closed-loop gain is 10 V/V. Its rail-to-rail input and output characteristics help maximize usable signal range on low-voltage supplies where conventional input and output stages would clip before the supply rails.

Key electrical characteristics include a typical quiescent current of 600 nA, a maximum quiescent current of 1 uA, a typical gain-bandwidth product of 100 kHz, and a typical input bias current of 5 nA. The operating voltage range is 1.4 V to 5.5 V, while the operating temperature range extends from -40 C to +125 C. These characteristics make the MCP6141 suitable for portable instrumentation, sensor interfaces, battery monitoring, medical-device signal conditioning, and low-power industrial controls.

The MCP6141’s low bias current reduces loading on high-impedance sensors, while rail-to-rail input operation improves usable dynamic range. The 100 kHz bandwidth supports accurate amplification of slow sensor signals and control-loop signals. Because the amplifier is non-unity-gain stable, feedback configurations should use a closed-loop gain of at least 10 V/V, and the output must remain within the supply rails.

Typical applications include low-frequency ECG and biomedical signal conditioning, portable sensor interfaces, battery-powered measurement systems, and low-current industrial sensing. Decoupling capacitors should be placed close to the supply pins, and the circuit should be checked for offset, noise, output-current, and capacitive-load limitations using the manufacturer’s typical application guidance.

This page consolidates the MCP6141’s operating characteristics, package information, drop-in alternatives, application guidance, and design notes for engineers evaluating low-power analog signal chains.

直接替換替代品,適用於 MCP6141-E/P — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

此系列的變體

與下列產品可直接替換的同系列型號: MCP6141-E/P (相同外形與佔位) — 差異在於 Input Common-Mode Range, Slew Rate, Output Swing, Package, Amplifier Type.

Microchip Technology
Input Common-Mode Range: -0.3 V minimum to VDD + 0.3 V maximum
Slew Rate: 24,000 V/us
Amplifier Type: Single operational amplifier
Microchip Technology
Input Common-Mode Range: Rail-to-rail input
Slew Rate: 0.003 V/us
Output Swing: Rail-to-rail output

MCP6141-I/P

✅ 直接替換 ⚠️ 規格未經驗證
Microchip Technology
📦 8-pin PDIP
1 circuit · Single operational amplifier · 1.4 V to 5.5 V · 600 nA typical · 1 uA maximum · 100 kHz typical · 10 V/V · -0.3 V minimum to VDD + 0.3 V maximum

聯絡詢價

查看資料表 →

MCP6142-E/P

✅ 直接替換 ⚠️ 規格未經驗證
📦 8-pin PDIP
Dual-amplifier family member rather than a single amplifier; the same 8-pin PDIP family footprint is used, but channel count differs.

📋 參考替代品(不在目錄中)

MCP6142-I/P

✅ 直接替換 ⚠️ 規格未經驗證
Microchip Technology
📦 8-pin PDIP
General-purpose operational amplifier · 2 circuits · 1.4 V to 5.5 V · 600 nA per amplifier · 1 uA per amplifier · 100 kHz · Rail-to-rail input · Rail-to-rail output

聯絡詢價

查看資料表 →

MCP6143-E/P

✅ 直接替換 ⚠️ 規格未經驗證
📦 8-pin PDIP
Same MCP6141 family and 8-pin PDIP family package; channel configuration and exact feature set differ from the single MCP6141.

📋 參考替代品(不在目錄中)

MCP6143-I/P

✅ 直接替換 ⚠️ 規格未經驗證
📦 8-pin PDIP
Same MCP6141 family and 8-pin PDIP family package; industrial temperature suffix and channel configuration differ from MCP6141-E/P.

📋 參考替代品(不在目錄中)

MCP6141-E/P 最大額定值與電氣特性

Product Type Single operational amplifier
Supply Voltage Range 1.4 V to 5.5 V
靜態電流 600 nA typical
Maximum Quiescent Current 1 uA maximum
Gain-Bandwidth Product 100 kHz typical
Input Bias Current 5 nA typical
Input Common-Mode Range Rail-to-rail
Output Swing Rail-to-rail
Minimum Stable Gain 10 V/V
CMRR 80 dB
Slew Rate 24000 V/us
工作溫度範圍 -40 C to +125 C
封裝 8-pin PDIP
安裝類型 Through-hole

MCP6141-E/P 8-pin pdip 腳位配置指南

MCP6141-E/P(8-pin pdip 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。

MCP6141-E/P 的 8-pin pdip 封裝腳位圖

無詳細腳位定義資料: MCP6141-E/P.

請參閱 資料表 以查看完整腳位配置。

典型應用

MCP6141-E/P 適用於 6 應用s: Battery-Powered Sensor Interfaces, Portable Biomedical Signal Conditioning, Low-Power Industrial Control Signals, Battery Voltage Monitoring, Portable Environmental Monitoring, Low-Power Instrumentation Buffering.

🧩

Battery-Powered Sensor Interfaces

The MCP6141-E/P fits low-power sensor front ends because its 1.4 V to 5.5 V supply range supports small battery-powered systems and its typical 600 nA quiescent current minimizes standby demand. The rail-to-rail input characteristic is useful when sensor output levels move close to either supply rail. Its typical 5 nA input bias current also reduces loading on high-impedance sensors. Use a closed-loop gain of at least 10 V/V and place the bypass capacitor close to the supply pins.

💊

Portable Biomedical Signal Conditioning

The MCP6141-E/P is suitable for low-level biomedical signal conditioning where low power and high input impedance are priorities. Its 5 nA typical input bias current minimizes source loading, while the rail-to-rail input and output stages make better use of the available 1.4 V to 5.5 V supply range. The 100 kHz typical gain-bandwidth product is appropriate for slow physiological signals rather than wideband diagnostic instrumentation. Medical systems must still meet their own electrical-safety and regulatory requirements.

🏭

Low-Power Industrial Control Signals

The MCP6141-E/P can amplify slow process-control signals in low-power industrial electronics because its 100 kHz typical gain-bandwidth product is sufficient for many sensor and control-loop signals. The low 600 nA typical quiescent current helps isolated or battery-backed monitoring modules consume less standby power. Its wide input range supports signals that approach the supply rails. Confirm the operating temperature requirement and use the manufacturer’s recommended grounding and layout practices.

⚡

Battery Voltage Monitoring

The MCP6141-E/P can serve as a low-power buffer or gain stage in a battery-voltage monitoring path. Rail-to-rail input and output behavior allows the circuit to operate with small headroom, while the 600 nA typical quiescent current limits the monitoring amplifier’s effect on battery life. The non-unity-gain-stable architecture requires a closed-loop gain of at least 10 V/V. The input network must also account for the amplifier’s input bias current and leakage.

🌐

Portable Environmental Monitoring

The MCP6141-E/P is appropriate for portable environmental-monitoring instruments that combine low-voltage sensors with long battery life. Its low input bias current helps preserve weak sensor signals, and the rail-to-rail input reduces the need for an artificial bias near mid-supply. The 100 kHz typical bandwidth is ample for temperature, humidity, gas, and environmental signals that vary slowly. Use local bypass capacitance and short feedback traces to preserve low-noise operation.

🔧

Low-Power Instrumentation Buffering

The MCP6141-E/P can be used in low-power instrumentation where a high-impedance source must drive a downstream measurement stage. Its 5 nA typical input bias current reduces loading, and its rail-to-rail input and output behavior support operation close to the supply limits. Because it is non-unity-gain stable, the circuit should use a gain of 10 V/V or higher rather than a unity-gain buffer configuration. Check offset, noise, and output-drive requirements against the manufacturer’s test conditions.

推薦產品摘要

MCP6142-I/P Microchip Technology 用於: Battery-Powered Sensor Interfaces, Low-Power Industrial Control Signals, Portable Environmental Monitoring MCP6143-I/P Related MCP6141-family low-power amplifier 用於: Battery-Powered Sensor Interfaces, Portable Environmental Monitoring MCP6142-E/P Dual low-power family option for paired signal channels 用於: Portable Biomedical Signal Conditioning, Battery Voltage Monitoring, Low-Power Instrumentation Buffering MCP6141-I/P Microchip Technology 用於: Portable Biomedical Signal Conditioning, Battery Voltage Monitoring, Low-Power Instrumentation Buffering MCP6143-E/P Related family member for additional low-power signal paths 用於: Low-Power Industrial Control Signals
What is the MCP6141-E/P?
The MCP6141-E/P is a single, general-purpose operational amplifier from Microchip Technology with a typical quiescent current of 600 nA. According to the manufacturer product page, it supports rail-to-rail input and output operation from a 1.4 V to 5.5 V supply and has a typical gain-bandwidth product of 100 kHz. It is suited to battery-powered and low-leakage signal-conditioning designs.
What is the operating voltage of MCP6141-E/P?
The MCP6141-E/P operates from 1.4 V to 5.5 V. This low supply range allows operation from a single-cell or low-voltage battery source, while also supporting conventional low-voltage rails. The manufacturer’s MCP6141 product page identifies the 1.4 V to 5.5 V range, and the device datasheet describes operation with single supplies as low as 1.4 V.
What is the quiescent current of MCP6141-E/P?
The MCP6141-E/P has a typical quiescent current of 600 nA and a maximum quiescent current of 1 uA per amplifier. This low operating current reduces the load placed on a battery or low-power supply and makes the device useful for portable instrumentation and always-on sensing. The current rating is specified by Microchip Technology for the MCP6141 family.
Does MCP6141-E/P support rail-to-rail input and output?
Yes. The MCP6141-E/P supports rail-to-rail input and output operation. Rail-to-rail input behavior allows the input common-mode voltage to approach the supply limits, while rail-to-rail output operation increases the usable output-voltage range. These features are particularly useful in low-voltage systems where signal swing must be maximized.
What is the gain-bandwidth product of MCP6141-E/P?
The MCP6141-E/P has a typical gain-bandwidth product of 100 kHz. This bandwidth is suited to low-frequency sensor signals, measurement channels, and slowly changing control signals rather than high-speed video or communications paths. The manufacturer product page lists 100 kHz as the typical GBWP for MCP6141.
What is the minimum gain for MCP6141-E/P?
The MCP6141-E/P is non-unity-gain stable and is intended for closed-loop gains of 10 V/V or higher. Designers should avoid relying on voltage-follower operation or other near-unity-gain configurations. The minimum-gain requirement is important when selecting feedback values and when evaluating whether an alternative op amp can replace the MCP6141.
Where can I download the MCP6141-E/P datasheet?
The manufacturer datasheet PDF is available at the Microchip Technology URL recorded on this page. It describes the MCP6141/2/3/4 family, including the low-voltage supply range, rail-to-rail operation, quiescent current, gain stability, and electrical characteristics. Use the manufacturer document for pin assignments, recommended operating conditions, and application details.
Where can I find the MCP6141-E/P pinout?
The MCP6141-E/P pin assignment should be taken from the pin-description table in the Microchip Technology MCP6141 family datasheet. The component is identified in distributor listings as an 8-pin PDIP package. Use the package drawing and pin table together when assigning signal, supply, and feedback connections on the PCB.
What can replace MCP6141-E/P?
The closest same-family choices are the Microchip MCP6142-E/P and MCP6142-I/P, subject to confirming channel count and temperature-grade requirements. The MCP6141-E/P is a single amplifier in an 8-pin PDIP, while the MCP6142 family is dual-channel, so it is a functional same-package option rather than an unconditional functional replacement for every board.
Is MCP6141-I/P a drop-in replacement for MCP6141-E/P?
MCP6141-I/P is the same MCP6141 family and 8-pin PDIP configuration, making it a practical same-package replacement candidate. The main difference is the temperature grade: the -E/P suffix denotes the extended-temperature option, while -I/P denotes the industrial-temperature option. Confirm the required temperature range and purchasing availability before substituting it.
What is the difference between MCP6141-E/P and MCP6142-E/P?
The MCP6141-E/P contains one amplifier, while the MCP6142-E/P is a dual-amplifier family member in the same 8-pin PDIP family. Their low-power characteristics and voltage range are related, but a dual device cannot automatically replace a single-device footprint without checking the pinout, channel usage, and unused-channel configuration.
Is MCP6141-E/P suitable for battery-powered sensor interfaces?
Yes. The MCP6141-E/P is well suited to battery-powered sensor interfaces because its typical quiescent current is only 600 nA, its supply range begins at 1.4 V, and its input is rail-to-rail. These characteristics reduce supply consumption and improve signal range. High-impedance sensors also benefit from the typical 5 nA input bias current.
Can MCP6141-E/P be used for low-frequency medical signal conditioning?
The MCP6141-E/P can be used for low-frequency medical signal conditioning when the circuit stays within the device’s gain, bandwidth, input, output, and leakage limits. Its 100 kHz typical gain-bandwidth product and 5 nA typical input bias current are useful for low-level sensor amplification. Medical designs must also satisfy their own safety, isolation, and validation requirements.
How should decoupling and PCB layout be handled for MCP6141-E/P?
Place the supply bypass capacitor close to the MCP6141-E/P supply pins and route the supply and ground connections with low loop area. Keep input and feedback traces short, especially when the source impedance is high. The manufacturer datasheet’s recommended application circuit should be used as the starting point for grounding, decoupling, and output-load requirements.
Does MCP6141-E/P require a minimum load or gain configuration?
The MCP6141-E/P is non-unity-gain stable, so it should be operated at a closed-loop gain of 10 V/V or higher. It is not intended for unity-gain voltage-follower use. The exact recommended feedback network and output-load conditions should be taken from the manufacturer datasheet, and the gain requirement must be included in any replacement qualification.

工程參考資料,適用於 MCP6141-E/P — 比較、設計指引及合規資訊。

選型指南

Choose MCP6141-E/P when a single, low-power op amp is needed for a 1.4 V to 5.5 V design and the extended-temperature grade is appropriate. Its 600 nA typical quiescent current, rail-to-rail input/output behavior, and 100 kHz typical gain-bandwidth product are well matched to battery-powered sensors, portable instrumentation, and slow industrial signals. MCP6141-I/P is the closest same-family single-amplifier alternative when the industrial temperature grade is sufficient. MCP6142-E/P and MCP6142-I/P can be useful when a dual amplifier is preferred, but their channel count and unused-pin handling must be checked against the original circuit. MCP6143 variants should be selected only after confirming the required channel configuration and pin functions. All listed candidates use the same 8-pin PDIP family package, but they are not electrically interchangeable in every application.

與替代品比較

參數 本產品 MCP6141-I/P MCP6142-E/P MCP6142-I/P MCP6143-E/P MCP6143-I/P
Package 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Supply Voltage Range 1.4 V to 5.5 V 1.4 V to 5.5 V 1.4 V to 5.5 V 1.4 V to 5.5 V 1.4 V to 5.5 V 1.4 V to 5.5 V
Gain-Bandwidth Product 100 kHz typical 100 kHz typical 100 kHz typical 100 kHz typical 100 kHz typical 100 kHz typical
Temperature Grade -E/P extended grade -I/P industrial grade -E/P extended grade -I/P industrial grade -E/P extended grade -I/P industrial grade
Input and Output Operation Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output

主要差異化特點

  • Lower quiescent current than a typical general-purpose precision amplifier (對比MCP6141-I/P)
  • Single-amplifier configuration preserves the simplest 8-pin PDIP implementation (對比MCP6142-E/P)
  • Rail-to-rail input and output support low-voltage signal-chain headroom (對比MCP6143-I/P)

設計說明

Place the supply bypass capacitor immediately adjacent to the MCP6141-E/P supply and ground pins. Keep the input, output, and feedback traces short so that the amplifier’s very low 600 nA typical quiescent current does not have to compete with leakage through long PCB paths. Confirm that the selected bypass capacitor has acceptable voltage bias and leakage characteristics for the actual supply range.

Do not configure MCP6141-E/P as a unity-gain voltage follower. The device is non-unity-gain stable and should use a closed-loop gain of at least 10 V/V. This requirement must also be checked during replacement testing because a substitute with unity-gain stability may behave differently in the same feedback network.

For high-impedance sources, keep the op-amp input pins and feedback components away from long exposed traces, connectors, and switching nodes. Because the typical input bias current is only 5 nA, even small PCB leakage can affect a high-impedance sensor interface. Use a protective ground arrangement around the input where appropriate and verify the complete board’s leakage behavior.

Check the closed-loop bandwidth against the signal bandwidth and the 100 kHz typical gain-bandwidth product. A gain of 10 V/V leaves substantially less closed-loop bandwidth than the gain-bandwidth product, while higher gains can be useful for slow sensor signals. Avoid driving a large capacitive load directly from the output unless the load condition is supported by the manufacturer’s guidance.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

Compliance status was not stated in the manufacturer product-page or distributor snippets. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification requirements with the manufacturer before releasing a regulated design.

資料驗證日期: 2026-11-10 — 資料由 XAIPART 元件工程團隊驗證及整理

相關搜尋

mcp6141 datasheet MCP6141-E/P datasheet MCP6141-E/P pinout MCP6141-E/P equivalent MCP6141-E/P replacement MCP6141-E/P price MCP6141-E/P stock MCP6141-E/P lead time MCP6141 600 nA op amp MCP6141 rail to rail amplifier MCP6141-E/P vs MCP6142-E/P MCP6141-E/P 8-pin PDIP MCP6141-E/P battery powered MCP6141-E/P application circuit What is the operating voltage of MCP6141-E/P?

相關元件與詞彙

Microchip Technology MCP6141-E/P MCP6141 MCP6142-E/P MCP6142-I/P MCP6143-E/P MCP6143-I/P Operational amplifier Op amp Analog IC Low-power amplifier Rail-to-rail input Rail-to-rail output Quiescent current Gain-bandwidth product GBWP Input bias current Non-unity-gain stable 8-pin PDIP DIP package Through-hole package Battery-powered electronics Sensor interface Portable instrumentation Low-voltage analog signal conditioning
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情