MCP6141-E/P - 600 nA Low-Power RRIO Op Amp | Microchip Technology
料号: MCP6141-E/P ✓ 量产中MCP6141-E/P 概述
An operational amplifier, or op amp, is an analog building block that uses high open-loop gain to amplify the difference between two input voltages. MCP6141 belongs to the non-unity-gain-stable amplifier family, so the minimum recommended closed-loop gain is 10 V/V. Its rail-to-rail input and output characteristics help maximize usable signal range on low-voltage supplies where conventional input and output stages would clip before the supply rails.
Key electrical characteristics include a typical quiescent current of 600 nA, a maximum quiescent current of 1 uA, a typical gain-bandwidth product of 100 kHz, and a typical input bias current of 5 nA. The operating voltage range is 1.4 V to 5.5 V, while the operating temperature range extends from -40 C to +125 C. These characteristics make the MCP6141 suitable for portable instrumentation, sensor interfaces, battery monitoring, medical-device signal conditioning, and low-power industrial controls.
The MCP6141’s low bias current reduces loading on high-impedance sensors, while rail-to-rail input operation improves usable dynamic range. The 100 kHz bandwidth supports accurate amplification of slow sensor signals and control-loop signals. Because the amplifier is non-unity-gain stable, feedback configurations should use a closed-loop gain of at least 10 V/V, and the output must remain within the supply rails.
Typical applications include low-frequency ECG and biomedical signal conditioning, portable sensor interfaces, battery-powered measurement systems, and low-current industrial sensing. Decoupling capacitors should be placed close to the supply pins, and the circuit should be checked for offset, noise, output-current, and capacitive-load limitations using the manufacturer’s typical application guidance.
This page consolidates the MCP6141’s operating characteristics, package information, drop-in alternatives, application guidance, and design notes for engineers evaluating low-power analog signal chains.
直接替换替代料: MCP6141-E/P ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MCP6141-E/P (相同外形与封装尺寸) ——差异在于 Input Common-Mode Range, Slew Rate, Output Swing, Package, Amplifier Type.
MCP6141-I/P
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MCP6142-E/P
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MCP6142-I/P
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →MCP6143-E/P
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MCP6143-I/P
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
MCP6141-E/P 最大额定值与电气特性
| Product Type | Single operational amplifier |
| Supply Voltage Range | 1.4 V to 5.5 V |
| 静态电流 | 600 nA typical |
| Maximum Quiescent Current | 1 uA maximum |
| Gain-Bandwidth Product | 100 kHz typical |
| Input Bias Current | 5 nA typical |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Minimum Stable Gain | 10 V/V |
| CMRR | 80 dB |
| Slew Rate | 24000 V/us |
| 工作温度范围 | -40 C to +125 C |
| 封装 | 8-pin PDIP |
| 安装类型 | Through-hole |
MCP6141-E/P 8-pin pdip 引脚配置指南
MCP6141-E/P(8-pin pdip 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: MCP6141-E/P.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MCP6141-E/P 适用于 6 应用s: Battery-Powered Sensor Interfaces, Portable Biomedical Signal Conditioning, Low-Power Industrial Control Signals, Battery Voltage Monitoring, Portable Environmental Monitoring, Low-Power Instrumentation Buffering.
Battery-Powered Sensor Interfaces
The MCP6141-E/P fits low-power sensor front ends because its 1.4 V to 5.5 V supply range supports small battery-powered systems and its typical 600 nA quiescent current minimizes standby demand. The rail-to-rail input characteristic is useful when sensor output levels move close to either supply rail. Its typical 5 nA input bias current also reduces loading on high-impedance sensors. Use a closed-loop gain of at least 10 V/V and place the bypass capacitor close to the supply pins.
推荐
Portable Biomedical Signal Conditioning
The MCP6141-E/P is suitable for low-level biomedical signal conditioning where low power and high input impedance are priorities. Its 5 nA typical input bias current minimizes source loading, while the rail-to-rail input and output stages make better use of the available 1.4 V to 5.5 V supply range. The 100 kHz typical gain-bandwidth product is appropriate for slow physiological signals rather than wideband diagnostic instrumentation. Medical systems must still meet their own electrical-safety and regulatory requirements.
推荐
Low-Power Industrial Control Signals
The MCP6141-E/P can amplify slow process-control signals in low-power industrial electronics because its 100 kHz typical gain-bandwidth product is sufficient for many sensor and control-loop signals. The low 600 nA typical quiescent current helps isolated or battery-backed monitoring modules consume less standby power. Its wide input range supports signals that approach the supply rails. Confirm the operating temperature requirement and use the manufacturer’s recommended grounding and layout practices.
推荐
Battery Voltage Monitoring
The MCP6141-E/P can serve as a low-power buffer or gain stage in a battery-voltage monitoring path. Rail-to-rail input and output behavior allows the circuit to operate with small headroom, while the 600 nA typical quiescent current limits the monitoring amplifier’s effect on battery life. The non-unity-gain-stable architecture requires a closed-loop gain of at least 10 V/V. The input network must also account for the amplifier’s input bias current and leakage.
推荐
Portable Environmental Monitoring
The MCP6141-E/P is appropriate for portable environmental-monitoring instruments that combine low-voltage sensors with long battery life. Its low input bias current helps preserve weak sensor signals, and the rail-to-rail input reduces the need for an artificial bias near mid-supply. The 100 kHz typical bandwidth is ample for temperature, humidity, gas, and environmental signals that vary slowly. Use local bypass capacitance and short feedback traces to preserve low-noise operation.
推荐
Low-Power Instrumentation Buffering
The MCP6141-E/P can be used in low-power instrumentation where a high-impedance source must drive a downstream measurement stage. Its 5 nA typical input bias current reduces loading, and its rail-to-rail input and output behavior support operation close to the supply limits. Because it is non-unity-gain stable, the circuit should use a gain of 10 V/V or higher rather than a unity-gain buffer configuration. Check offset, noise, and output-drive requirements against the manufacturer’s test conditions.
推荐
推荐产品汇总
工程参考数据: MCP6141-E/P ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MCP6141-I/P | MCP6142-E/P | MCP6142-I/P | MCP6143-E/P | MCP6143-I/P |
|---|---|---|---|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Supply Voltage Range | 1.4 V to 5.5 V | 1.4 V to 5.5 V | 1.4 V to 5.5 V | 1.4 V to 5.5 V | 1.4 V to 5.5 V | 1.4 V to 5.5 V |
| Gain-Bandwidth Product | 100 kHz typical | 100 kHz typical | 100 kHz typical | 100 kHz typical | 100 kHz typical | 100 kHz typical |
| Temperature Grade | -E/P extended grade | -I/P industrial grade | -E/P extended grade | -I/P industrial grade | -E/P extended grade | -I/P industrial grade |
| Input and Output Operation | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output |
关键差异点
- Lower quiescent current than a typical general-purpose precision amplifier (对比 MCP6141-I/P)
- Single-amplifier configuration preserves the simplest 8-pin PDIP implementation (对比 MCP6142-E/P)
- Rail-to-rail input and output support low-voltage signal-chain headroom (对比 MCP6143-I/P)
设计说明
Place the supply bypass capacitor immediately adjacent to the MCP6141-E/P supply and ground pins. Keep the input, output, and feedback traces short so that the amplifier’s very low 600 nA typical quiescent current does not have to compete with leakage through long PCB paths. Confirm that the selected bypass capacitor has acceptable voltage bias and leakage characteristics for the actual supply range.
Do not configure MCP6141-E/P as a unity-gain voltage follower. The device is non-unity-gain stable and should use a closed-loop gain of at least 10 V/V. This requirement must also be checked during replacement testing because a substitute with unity-gain stability may behave differently in the same feedback network.
For high-impedance sources, keep the op-amp input pins and feedback components away from long exposed traces, connectors, and switching nodes. Because the typical input bias current is only 5 nA, even small PCB leakage can affect a high-impedance sensor interface. Use a protective ground arrangement around the input where appropriate and verify the complete board’s leakage behavior.
Check the closed-loop bandwidth against the signal bandwidth and the 100 kHz typical gain-bandwidth product. A gain of 10 V/V leaves substantially less closed-loop bandwidth than the gain-bandwidth product, while higher gains can be useful for slow sensor signals. Avoid driving a large capacitive load directly from the output unless the load condition is supported by the manufacturer’s guidance.
合规信息
Compliance status was not stated in the manufacturer product-page or distributor snippets. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification requirements with the manufacturer before releasing a regulated design.