OPA547T-1 - 60V High-Current Op Amp | Texas Instruments
MPN: OPA547T-1 ✓ NakahandaOPA547T-1 Ulas
An operational amplifier is an analog signal-conditioning component that uses differential feedback to control gain, impedance conversion, and signal amplitude. The OPA547T-1 extends the conventional operational-amplifier hierarchy into the power-amplifier and current-driver segment, where a low-voltage precision amplifier is unsuitable because the output must deliver substantially greater current and operate across a wider supply-voltage range. Its shutdown control adds a controlled operating-state option for systems that need to disconnect the output stage.
The manufacturer identifies the OPA547 family as a high-voltage, high-current operational amplifier with fully protected thermal shutdown, adjustable current limit, and output-disable control. Its broad supply range supports single-supply operation to 60 V and dual-supply operation to ±30 V. The 500 mA continuous output-current capability is especially useful when driving loads that exceed the current capability of ordinary precision amplifiers.
The OPA547T-1 is specified at a 1 MHz gain-bandwidth product and a 6 V/µs slew rate. These figures determine how quickly the closed-loop amplifier can respond to changing input signals. Because the device is intended for high-current and high-voltage service, output-drive protection, current limiting, and thermal management are as important as conventional small-signal accuracy when designing a dependable circuit.
Typical uses include high-voltage current drivers, audio power stages, industrial actuator interfaces, power-supply control loops, programmable laboratory equipment, and motor or solenoid drive circuits. The device can operate from an 8 V minimum total supply, reach 60 V total supply, and support output-disable control for systems requiring a controlled output state.
PCB design should preserve the seven-pin TO-220 package footprint, provide adequate copper for heat dissipation, and use short, robust output routes where the load current can approach 500 mA. Designers must also account for the amplifier’s high-voltage operating environment, including insulation clearances, connector spacing, and protection against transient events.
This page combines manufacturer ordering information, verified distributor availability, device-level specifications, replacement guidance, application notes, and engineering comparison guidance. It is intended to help engineers determine whether the OPA547T-1 provides the required voltage range, current capability, package compatibility, protection features, and thermal margin for their design.
Mga alternatibo na pwedeng ilagay na OPA547T-1 — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok OPA547T-1 (parehas na form factor at footprint) — pagkakaiba sa Package.
OPA547T-1G3
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
OPA547T-1 Mga Pinakamataas na Rating at Electrical Characteristics
| Amplifier Type | Single-channel high-voltage, high-current operational amplifier |
| Number of Channels | 1 channel |
| Total Supply Voltage Range | 8 V to 60 V |
| Single-Supply Maximum | +60 V |
| Dual-Supply Maximum | ±30 V |
| Continuous Output Current | 500 mA |
| Gain-Bandwidth Product | 1 MHz |
| Slew Rate | 6 V/µs |
| Output Disable Control | Yes |
| Limit ng Current | Adjustable |
| Thermal Shutdown | Yes |
| Hanay ng Temperature na Operasyon | -40 °C to +85 °C |
| Packhaging | TO-220 (KC), 7 pins |
| Uri ng Pagpapasok | Through-hole |
| Lead Stagger | Straight lead |
Pin Configuration ng OPA547T-1
| Pin 1 | E/S — Enable or shutdown input; can be monitored for thermal-shutdown status |
| Pin 2 | NC — Not connected |
| Pin 3 | V- — Negative supply connection |
| Pin 4 | V+ — Positive supply connection |
| Pin 5 | NC — Not connected |
| Pin 6 | OUT — Amplifier output |
| Pin 7 | NC — Not connected |
Tipikal na mga Gamit
OPA547T-1 ay nararapat para sa 6 aplikasyons: High-Voltage Audio Power Driver, Industrial Solenoid and Actuator Driver, Power-Supply Control and Monitoring, Programmable Test and Measurement, Motor and Solenoid Power Control, Precision High-Current Feedback Amplifier.
High-Voltage Audio Power Driver
The OPA547T-1 fits high-voltage audio output stages that require substantially more current than a conventional precision operational amplifier can deliver. Its 500 mA continuous output-current capability supports line-driver and speaker-buffer arrangements, while the 6 V/µs slew rate provides faster large-signal response than ordinary low-power amplifiers. The 8 V to 60 V total supply range also permits operation above the limits of many signal op amps. In a practical design, configure feedback for the required closed-loop gain, check output-swing limits against the load, and use output isolation where the load can present nonlinear or reactive behavior. Thermal performance and current limiting are critical because sustained high-current operation can dissipate substantial power in the TO-220 package.
Inirekomenda
Industrial Solenoid and Actuator Driver
OPA547T-1 is suitable for current-driven industrial actuators where the control signal must operate across a higher voltage range than conventional instrumentation amplifiers. Its 500 mA continuous output rating can serve solenoid, relay, or valve-driver interfaces when the load remains within the device’s electrical and thermal limits. The adjustable current limit provides a design control for limiting fault current, while thermal shutdown protects the amplifier during abnormal loading. Place the output stage so that high-current wiring is short and isolated from sensitive input routing. Verify inductive-load protection, including flyback current paths and voltage transients, because a 60 V maximum supply does not by itself establish safe handling of arbitrary inductive kickback. The -40 °C to +85 °C rated range supports many industrial ambient environments.
Inirekomenda
Power-Supply Control and Monitoring
The OPA547T-1 can be used as the high-current error amplifier or driver in laboratory and industrial power-control circuits. Its 1 MHz gain-bandwidth product provides substantially more bandwidth than a slow power-control loop usually requires, allowing compensation to focus on loop stability rather than amplifier bandwidth limits. The 6 V/µs slew rate supports rapid correction of output errors, and the 8 V to 60 V supply range accommodates elevated bus voltages. In implementation, isolate the power-stage output from the sensitive feedback network and account for the amplifier’s ability to source or sink 500 mA continuous current. Current-limit settings, output stability, and package dissipation should be verified across startup, steady-state, and short-circuit conditions to avoid unexpected stress on the power stage.
Inirekomenda
Programmable Test and Measurement
OPA547T-1 is appropriate for programmable power-supply test fixtures, source-measurement output stages, and laboratory current-driver circuits. A 500 mA continuous output rating provides useful margin for driving resistive, active, or feedback-controlled loads, while the 1 MHz gain-bandwidth product and 6 V/µs slew rate accommodate rapidly changing test commands. The output-disable control can help a fixture enter a defined state between measurements. Engineers should use the shutdown and thermal-status functions according to the manufacturer guidance and keep the amplifier’s supply rails compatible with the desired output range. For precision instrumentation, the high-power operational-amplifier architecture should not be confused with a low-offset precision amplifier; add separate measurement, calibration, and error-correction channels when output accuracy is critical.
Inirekomenda
Motor and Solenoid Power Control
OPA547T-1 is useful in closed-loop motor-current and solenoid-control circuits that require an analog error amplifier with unusually strong output drive. The 500 mA continuous output capability can reduce the need for a separate output-buffer stage, and the 6 V/µs slew rate allows the amplifier to respond to control-loop corrections without the severe bandwidth restriction of a low-power op amp. A 60 V maximum total supply can support elevated motor buses, subject to transient and absolute-maximum requirements. The design must still account for motor-generated back-EMF, contactor transients, and ground offsets. Use protective steering around the amplifier, keep switching-node current out of feedback routing, and derive thermal margins from the worst-case load duty cycle rather than a nominal operating point.
Inirekomenda
Precision High-Current Feedback Amplifier
OPA547T-1 can serve as a high-current feedback amplifier in a power-converter or voltage-regulator control path where the feedback network requires stronger drive than a conventional signal amplifier can provide. Its 1 MHz gain-bandwidth product leaves substantial bandwidth above typical power-converter crossover frequencies, while the 6 V/µs slew rate improves large-signal response. The broad 8 V to 60 V supply range makes it useful in elevated-voltage laboratory and industrial converters. Compensation should be designed around the complete amplifier, load, and switching topology rather than assuming generic stability. Keep feedback traces short, place compensation components close to the relevant pins, and confirm that the amplifier’s saturation and shutdown behavior do not disrupt system startup or fault recovery.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for OPA547T-1 — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | OPA547T-1G3 |
|---|---|---|
| Package | TO-220 (KC), 7 pins | TO-220 (KC), 7 pins |
| Brand | Texas Instruments | Texas Instruments |
Pangunahing mga Pagkakaiba
- Combines a wide supply range with high continuous output current (kumpara saOPA547T-1G3)
- Maintains a 1 MHz gain-bandwidth product for high-current drive (kumpara saOPA547T-1G3)
- Provides integrated protection and controlled output disable (kumpara saOPA547T-1G3)
Talaan ng Disenyo
Treat the OPA547T-1 as a power component rather than a conventional small-signal amplifier. Estimated: at a 30 V total supply, 15 V output, and 500 mA continuous load, output-stage dissipation can approach 7.5 W before accounting for other losses; actual dissipation depends on the amplifier architecture, quiescent current, load waveform, and output-swing behavior. Use the manufacturer thermal calculations to select copper area, heat sinking, airflow, and the maximum duty cycle. Do not infer safe operation from the 500 mA current rating alone.
Route the output and supply-current paths with conductors and copper areas sized for the intended load current, and keep their switching-node geometry physically separated from the input and feedback nodes. Place input compensation and feedback components close to pins 1, 3, 4, and 6 where the circuit requires them. Because the package can operate at voltages up to 60 V, maintain conservative copper-to-copper and board-edge clearances in accordance with the PCB-material and contamination requirements of the final product.
Do not substitute OPA547T, OPA548T-1, or another related amplifier solely because its family name and package are similar. Check straight versus staggered leads, pin function, supply range, continuous-current rating, current-limit implementation, thermal protection, bandwidth, and slew rate. For a board designed specifically for OPA547T-1, the documented OPA547T-1G3 is the closest same-package ordering alternative, but production and environmental differences still require confirmation from the manufacturer ordering information.
Design the shutdown and supply sequencing around the E/S function and ensure the amplifier cannot begin operating with an undefined control state. The E/S connection can also be monitored for thermal-shutdown status according to the manufacturer guidance. Use separate protection for inductive or capacitive loads so that switching transients do not exceed the amplifier’s absolute limits. Confirm that supply decoupling, wiring inductance, and load-return paths are compatible with the selected gain and compensation network.
Impormasyon ng Pagsunod sa Kautusan
The verified ordering and comparison records identify OPA547T-1 as a Texas Instruments OPA547-family device, but they do not explicitly establish the material-compliance fields. No compliance status should be inferred from the suffix or package alone.