OPA548T-1 - 3A High-Voltage Power Op Amp | Texas Instruments
MPN: OPA548T-1 ✓ ActiveOPA548T-1 Overview
A power operational amplifier is a specialized type of operational amplifier designed to source or sink substantial output current. Within the signal-chain hierarchy, the OPA548 belongs to the operational-amplifier category, amplifier IC category, and broader semiconductor and analog-signal-processing markets. Unlike a conventional precision op amp, it combines wide supply-voltage capability, high current capability, and thermal shutdown in a package intended for exposed PCB mounting.
The OPA548 uses laser-trimmed monolithic circuitry to provide low-level signal accuracy together with high output-voltage and current capability. Its electrical characteristics support motor-drive, loudspeaker, audio-amplifier, and power-converter interface applications where the load requires substantially more current than a conventional amplifier can provide. The thermal-shutdown E/S output can be monitored to identify an over-temperature condition.
The wide supply range supports single-supply and dual-supply systems operating between 8 V and 60 V total. A typical gain-bandwidth product of 1 MHz supports closed-loop amplifier configurations through the audio and lower-frequency control ranges, while the 10 V/µs slew rate improves large-signal response. These figures describe the device's macro performance; precision application design should use the complete manufacturer datasheet for minimum and maximum limits, load conditions, and configuration dependencies.
Typical applications include bridge-connected audio stages, DC and AC motor drivers, laser-diode bias circuits, power-converter control loops, laboratory output stages, and high-current actuator interfaces. The 3 A typical output-current capability is especially useful for low-impedance loads, while the ±30 V maximum supply voltage permits substantial output swing without moving to a lower-voltage amplifier family.
Thermal management is the central implementation constraint. The TO-220 tab must be connected to an appropriate copper area and, where required, a thermal interface compound and heatsink. The design should minimize copper trace resistance, keep the amplifier close to its load, and monitor the E/S thermal-shutdown indication. Incorrect grounding, insufficient output-stage protection, or operation beyond the device's safe area can cause oscillation or failure.
This product page combines the manufacturer's device description with package, application, comparison, and engineering guidance. It also identifies the distinction between OPA548T-1 and other OPA548 ordering variants and provides practical selection criteria for power-amplifier, motor-drive, and audio implementations.
Drop-in alternatives for OPA548T-1 — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.
Variants in this series
Same-series models that are drop-in compatible with OPA548T-1 (same form factor and footprint) — differing in Amplifier Type, Package, Thermal Shutdown.
OPA548T
✅ Drop-InContact for price
View Datasheet →OPA548T-1 Maximum Ratings & Electrical Characteristics
| Amplifier Type | Single-channel high-voltage, high-current operational amplifier |
| Number of Channels | 1 channel |
| Supply Voltage Range | ±4 V to ±30 V |
| Total Supply Voltage Range | 8 V to 60 V |
| Typical Output Current | 3 A |
| Typical Gain-Bandwidth Product | 1 MHz |
| Typical Slew Rate | 10 V/µs |
| Output Voltage Swing | Wide output-voltage swing; exact limits depend on load and supply conditions |
| Thermal Shutdown | Yes; E/S output can be monitored |
| Package | 7-lead TO-220 power package |
| Mounting Type | Through-hole power package |
| RoHS Status | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
OPA548T-1 7-lead to-220 power package Pin Configuration Guide
Pin configuration for OPA548T-1 (7-lead to-220 power package package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.
No detailed pinout data available for OPA548T-1.
Refer to the datasheet for full pin configuration.
Typical Applications
OPA548T-1 is suitable for 6 applications: High-Current Audio Output Stage, DC Motor Drive, Power Converter Control Loop, Laser and Photodiode Bias Control, Laboratory Power Output Stage, Actuator and Solenoid Interface.
High-Current Audio Output Stage
The OPA548T-1 fits high-current audio output stages because its typical 3 A output current can drive lower-impedance loudspeaker networks more effectively than a conventional precision op amp. Its 1 MHz gain-bandwidth product and 10 V/µs slew rate provide useful bandwidth and large-signal response for audio-band closed-loop designs, while supplies up to ±30 V permit a substantial output-voltage swing. The amplifier should be configured as a power stage with feedback set for the intended load, and the output path must include protection appropriate to the speaker and amplifier topology. Reactive speaker loads can introduce stability risk, so evaluate phase margin, crossover distortion, and current behavior across the frequency range. The TO-220 tab requires a low-resistance thermal path and an application-appropriate heatsink.
Recommended
DC Motor Drive
OPA548T-1 is well suited to voltage-mode DC motor drive because it can operate from ±30 V and provide a typical 3 A output current. Its 10 V/µs typical slew rate allows the amplifier output to follow command-voltage transitions with lower delay than a general-purpose low-current op amp. In a typical implementation, the amplifier drives the motor terminals from a control signal, with current sensing or a driver stage added where precise torque control is required. Inductive motor windings generate back-EMF and stored energy, so the design must include suitable flyback protection and avoid exposing the output to destructive transients. Thermal dissipation, motor stall current, and copper trace width require validation at the worst operating condition.
Recommended
Power Converter Control Loop
OPA548T-1 can serve as the high-current error amplifier or power stage in a boost, flyback, or other power-converter topology requiring high-voltage and high-current drive capability. Its ±4 V to ±30 V operating range supports elevated bus voltages, and its 10 V/µs typical slew rate is useful when the control loop must respond to rapid feedback corrections. The 1 MHz typical gain-bandwidth product places an upper limit on how aggressively the loop can be compensated, so the application must include suitable compensation and output filtering. A practical design should use the wide output swing conservatively, minimize compensation-node capacitance, and verify stability with the complete power stage and load. The thermal-shutdown E/S indication can support fault handling.
Recommended
Laser and Photodiode Bias Control
OPA548T-1 can drive precision current or voltage bias loads in laser-diode and photodiode systems where the source or sink current exceeds ordinary operational-amplifier limits. Its typical 3 A output-current capability provides ample headroom for the load current, while the 1 MHz typical gain-bandwidth product can support feedback loops operating well above audio frequencies. The amplifier should be paired with a suitable current-sense element and protection network because direct semiconductor-diode drive can expose the output to damage from excessive current or reverse voltage. Compensation must account for the diode's junction capacitance and the feedback network's noise. A low-noise reference and careful grounding are important when the intended output current or modulation bandwidth is small.
Recommended
Laboratory Power Output Stage
OPA548T-1 is applicable to laboratory and instrumentation output stages that need to drive low-impedance or current-sensitive loads from a low-level command signal. The ±30 V maximum supply and typical 3 A output current provide considerably more range than a conventional precision amplifier, while the 10 V/µs slew rate supports responsive voltage changes. A practical instrument adds current limiting, offset or output-voltage calibration, and a thermal strategy suitable for sustained DC operation. Because the device is a power operational amplifier rather than a laboratory reference amplifier, noise, output impedance, and closed-loop accuracy must be characterized in the intended configuration. The 7-lead TO-220 package also requires careful isolation from sensitive measurement circuitry and adequate creepage where elevated voltages are present.
Recommended
Actuator and Solenoid Interface
OPA548T-1 can serve as the output interface for medium-current actuators and solenoid-like loads where a control amplifier must source or sink substantial current. Its typical 3 A output capability is suitable for many power actuator stages, and the ±4 V to ±30 V supply range permits operation across broad industrial voltage choices. The amplifier output should not be used without an appropriate flyback or transient clamp because inductive loads can return energy to the output node when switched. Current sensing can support closed-loop force or position control, while a dedicated driver may be preferred when rapid active current control or additional protection is required. The design should account for steady-state coil heating, driver dissipation, ground offsets, and the TO-220 thermal path.
Recommended
Engineering reference data for OPA548T-1 — comparison, design guidance, and compliance information.
Selection Guide
Comparison with Alternatives
| Parameter | This Product | OPA548T |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | TO-220-7 | TO-220-7 family |
| Ordering Package Code | KC | KVT |
| Amplifier Type | High-voltage, high-current power operational amplifier | High-voltage, high-current power operational amplifier |
| Number of Channels | 1 channel | 1 channel |
| Typical Output Current | 3 A | 3 A |
| Typical Gain-Bandwidth Product | 1 MHz | 1 MHz |
| Typical Slew Rate | 10 V/µs | 10 V/µs |
| Thermal Shutdown Indication | E/S output | E/S output |
Key Differentiators
- High-current output capability in a single power op amp (vs OPA548T)
- Wide supply and output operating range (vs OPA548T)
- Large-signal response for power-stage control (vs OPA548T)
- Built-in thermal-state monitoring (vs OPA548T)
Design Notes
Treat the TO-220 tab as the primary heat path and keep it electrically connected to the intended power or ground node specified by the manufacturer package drawing. Use a thermal interface compound and a correctly sized heatsink when the calculated output-stage dissipation is significant. Do not assume that PCB copper alone is adequate during sustained DC operation; evaluate the worst-case output voltage, load current, ambient temperature, and copper geometry.
Estimate: Pdiss = (VOUT - VSWRING) × IOUT. For a ±30 V supply and a 20 V output at 3 A, the estimated output-stage dissipation is 60 W before accounting for the amplifier's internal architecture. Use that result only as an early thermal-sizing estimate and verify it against the manufacturer safe-operating-area and thermal-resistance information. Keep supply and output paths short and use copper widths adequate for the peak current.
Do not substitute OPA548T for OPA548T-1 without checking the exact package drawings. Texas Instruments identifies OPA548T with the KVT ordering package and OPA548T-1 with KC. Confirm lead geometry, exposed-tab connection, pin functions, and thermal requirements before making a board-level substitution. Also provide appropriate flyback or clamp protection for motors, solenoids, and other inductive loads because stored energy can damage the power output stage.
Place the TO-220 device so its tab has direct access to a broad copper region, and keep high-current input and output traces short, wide, and free of unnecessary copper joints. Route sensitive feedback and compensation traces away from power-node switching edges. Use a low-impedance ground reference for feedback and current sensing, while ensuring that large return currents do not share sensitive signal-ground paths.
Compensate the amplifier for the actual load and feedback network rather than relying only on nominal small-signal bandwidth. A 1 MHz typical gain-bandwidth product and 10 V/µs typical slew rate provide useful design targets, but reactive loads, excess feedback capacitance, and power-supply decoupling can reduce stability. Use the manufacturer evaluation information and verify phase margin and transient response with the intended output wiring and protection components.
Compliance Information
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified for OPA548T-1. The manufacturer lists the OPA548 family as active.