SN75140P Dual Line Receiver, 5V | Texas Instruments
MPN: SN75140P ✓ NakahandaSN75140P Ulas
A dual line receiver is an interface integrated circuit that converts small differential or single-ended signals received over a cable or bus into logic-level outputs. In the broader semiconductor hierarchy, it belongs to interface ICs and performs the receiver function within a communications link. A line receiver complements a line driver: the driver places a signal onto the transmission line, while the receiver restores that signal to a valid logic level for the connected digital system.
The SN75140P supports a common reference voltage adjustable from 1.5 V to 3.5 V, allowing the switching threshold to be optimized for noise immunity in a particular system. Its ±100 mV input sensitivity enables recognition of small signals, while the low input current of less than 100 uA suits shared party-line arrangements. The two channels share one reference-voltage pin and one strobe input, reducing control overhead in a dual-channel bus interface.
TTL-compatible outputs and strobes allow the receiver to operate with conventional TTL logic. The device can also be used as a single-ended line receiver, a gated oscillator, or a level comparator. These functions make the same hardware applicable to data acquisition, bus monitoring, communications equipment, and systems in which a variable threshold is preferable to a fixed internal reference.
Typical applications include multipoint data buses, industrial control interfaces, peripheral data links, instrumentation interfaces, and legacy computer equipment. When the SN75140P is used with a compatible line driver such as the SN75453B, both devices can operate from one 5 V supply and occupy approximately the space of one 16-pin package. The SN75140P is characterized for operation from 0°C to 70°C.
The most important design consideration is threshold selection. Set the common reference voltage according to the signal amplitude, noise environment, and logic thresholds of the receiving system. Because the receiver uses a shared reference input, both channels normally use the same switching threshold. Account for propagation delay and ensure that the selected threshold preserves valid data timing across the complete bus operating range.
This page combines the manufacturer's device description with practical interface guidance, application context, pin-package information, and an explicit review of drop-in replacement availability. It distinguishes documented electrical capabilities from specifications that must be confirmed in the manufacturer datasheet, helping engineers make sourcing and circuit-design decisions without obscuring unresolved technical details.
Mga alternatibo na pwedeng ilagay na SN75140P — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Wala ng magagamit na drop-in alternatibo para sa produkto na ito.
Hilingin ang AlternatiboSN75140P Mga Spesipikasyon
| Device Type | Dual single-ended line receiver |
| Number of Receiver Channels | 2 channels |
| Volte ng Pagbibigay | 5 V |
| Input Sensitivity | ±100 mV |
| Input Current | <100 uA |
| Reference Voltage Range | 1.5 V to 3.5 V |
| Output Compatibility | TTL-compatible |
| Strobe Compatibility | TTL-compatible |
| Hanay ng Temperature na Operasyon | 0°C to 70°C |
| Packhaging | 8-pin PDIP |
| Uri ng Pagpapasok | Through-hole |
| Reference Control | Common reference-voltage pin |
| Strobe Control | Common strobe |
| Primary Application | Party-line data-bus systems |
| Additional Functions | Gated oscillator and level comparator |
Gabay sa Pin Configuration ng SN75140P 8-pin pdip
Pin configuration para sa SN75140P (8-pin pdip package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa SN75140P.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
SN75140P ay nararapat para sa 6 aplikasyons: Party-Line Data Bus, Industrial Control Data Interface, Peripheral Data Link, Data Acquisition and Instrumentation, Legacy Communications Equipment, Gated Oscillator and Level Comparator.
Party-Line Data Bus
The SN75140P fits a shared data-bus receiver because its input current is less than 100 uA and its common reference voltage can be adjusted from 1.5 V to 3.5 V. Two single-ended channels share one threshold and one strobe, simplifying system control while preserving TTL-compatible outputs. The threshold should be set from measured bus noise and signal amplitude so that valid transitions retain adequate margin. Because party-line operation connects multiple nodes, engineers should also verify fanout, stub loading, fault behavior, and timing across the complete network rather than treating the receiver as an isolated logic gate.
Inirekomenda
Industrial Control Data Interface
The SN75140P can condition small single-ended signals in an industrial control interface when a 5 V TTL-compatible output is required. Its ±100 mV sensitivity recognizes small signal changes, while the adjustable 1.5 V to 3.5 V reference permits threshold tuning around the signal present at the receiver. Place the receiver at the end of the line and account for propagation delay when designing the handshake or strobe timing. The shared reference also makes both channels convenient for paired status or data signals, although industrial temperature-range and compliance requirements should be checked separately for the finished system.
Inirekomenda
Peripheral Data Link
Use the SN75140P to recover TTL-level data from a peripheral line when the received amplitude is small and the logic threshold must be configurable. The dual receiver provides two channels in one 8-pin PDIP, reducing board area compared with separate single-channel parts. Its common strobe can support coordinated data qualification, while the common reference voltage simplifies threshold configuration across the pair. Validate the receiver's timing against the peripheral protocol and the line-driver characteristics, particularly when the cable introduces attenuation, reflections, or a measurable delay between transmitted and recovered data.
Inirekomenda
Data Acquisition and Instrumentation
The SN75140P can serve as a thresholded interface in instrumentation that accepts small single-ended sensor or control signals. The externally adjustable 1.5 V to 3.5 V reference allows the system to select a decision level suited to its signal distribution, and the ±100 mV sensitivity supports detection of relatively small changes. Its outputs are TTL-compatible, which simplifies connection to legacy digital acquisition equipment. Engineers should verify that the sensor source can drive the input capacitance and reference network, and should evaluate noise margin, input bias effects, and acquisition timing before treating the recovered output as a precision measurement.
Inirekomenda
Legacy Communications Equipment
The SN75140P is suitable for legacy communications equipment that combines a single 5 V supply, TTL-compatible logic, and a dual line receiver. Its two channels, common threshold, and common strobe provide a compact implementation for paired receive functions. The adjustable reference voltage is particularly useful when a fixed receiver threshold does not provide sufficient margin on an older cable system. Confirm pin assignments and timing in the Texas Instruments datasheet before substituting it into an existing board, and verify the receiver's behavior in the actual line environment rather than relying only on nominal input sensitivity.
Inirekomenda
Gated Oscillator and Level Comparator
Beyond its normal line-receiver role, the SN75140P can be configured as a gated oscillator or level comparator. The common reference input establishes the switching level, and the TTL-compatible strobe provides control over the output state. These functions can support simple event detection, pulse generation, or threshold-based control where a dedicated comparator or oscillator would be unnecessary. The external reference network must remain within the 1.5 V to 3.5 V range, and the design should account for input offset, noise around the threshold, propagation delay, and output loading. Confirm stable operation over the intended signal and temperature range.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for SN75140P — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto |
|---|---|
| Brand | Texas Instruments |
| Package | 8-pin PDIP |
| Receiver Configuration | Dual single-ended line receiver |
| Supply Voltage | 5 V |
| Input Sensitivity | ±100 mV |
| Input Current | <100 uA |
| Reference Voltage Range | 1.5 V to 3.5 V |
| Output Compatibility | TTL-compatible |
| Operating Temperature Range | 0°C to 70°C |
| Strobe Configuration | Common TTL-compatible strobe |
Pangunahing mga Pagkakaiba
- Externally adjustable common threshold (kumpara saFixed-threshold dual line receivers)
- Low loading for shared bus systems (kumpara saGeneral-purpose single-ended input comparators)
- Dual receiver with shared control (kumpara saTwo discrete single-channel receiver ICs)
Talaan ng Disenyo
Do not assume that the SN75140P and SN75453B are interchangeable: one is the receiver and the other is the driver. Verify the direction of every bus signal, the common reference connection, and the strobe polarity in the manufacturer pin table. When adapting an existing board, also confirm that the alternative's pin assignments and electrical limits match before treating it as a replacement.
Set the common reference voltage from measured signal levels and system noise rather than from a nominal midpoint alone. The documented adjustment range is 1.5 V to 3.5 V, and both channels share this threshold. Validate the selected value with worst-case input amplitude, line attenuation, receiver input current, and logic noise margin so that normal transitions do not approach the switching boundary.
Route the two receiver inputs away from switching-node and high-current return paths, and keep the common reference connection short to minimize pickup of external noise. Because both channels share the reference and strobe pins, noise on those routes affects both outputs. Use a stable reference network with an appropriate bypass path and place it near the receiver when the wiring is sensitive or the cable run is long.
Impormasyon ng Pagsunod sa Kautusan
The manufacturer product page and datasheet listing do not state the requested environmental-compliance details in the available product information.