Texas Instruments

SN75140P Dual Line Receiver, 5V | Texas Instruments

MPN: SN75140P ✓ فعال
5 V Vdss <100 uA Id 8-pin PDIP Package
حداقل سفارش: 1 |

SN75140P نمای کلی

Texas Instruments SN75140P is a dual single-ended line receiver with TTL-compatible outputs and strobes, operating from a single 5 V supply in an 8-pin PDIP package. It provides two receiver channels, a common externally adjustable reference voltage, a common strobe, and input sensitivity of ±100 mV. The device is designed for party-line and data-bus systems where low input current and adjustable switching thresholds are important.

A dual line receiver is an interface integrated circuit that converts small differential or single-ended signals received over a cable or bus into logic-level outputs. In the broader semiconductor hierarchy, it belongs to interface ICs and performs the receiver function within a communications link. A line receiver complements a line driver: the driver places a signal onto the transmission line, while the receiver restores that signal to a valid logic level for the connected digital system.

The SN75140P supports a common reference voltage adjustable from 1.5 V to 3.5 V, allowing the switching threshold to be optimized for noise immunity in a particular system. Its ±100 mV input sensitivity enables recognition of small signals, while the low input current of less than 100 uA suits shared party-line arrangements. The two channels share one reference-voltage pin and one strobe input, reducing control overhead in a dual-channel bus interface.

TTL-compatible outputs and strobes allow the receiver to operate with conventional TTL logic. The device can also be used as a single-ended line receiver, a gated oscillator, or a level comparator. These functions make the same hardware applicable to data acquisition, bus monitoring, communications equipment, and systems in which a variable threshold is preferable to a fixed internal reference.

Typical applications include multipoint data buses, industrial control interfaces, peripheral data links, instrumentation interfaces, and legacy computer equipment. When the SN75140P is used with a compatible line driver such as the SN75453B, both devices can operate from one 5 V supply and occupy approximately the space of one 16-pin package. The SN75140P is characterized for operation from 0°C to 70°C.

The most important design consideration is threshold selection. Set the common reference voltage according to the signal amplitude, noise environment, and logic thresholds of the receiving system. Because the receiver uses a shared reference input, both channels normally use the same switching threshold. Account for propagation delay and ensure that the selected threshold preserves valid data timing across the complete bus operating range.

This page combines the manufacturer's device description with practical interface guidance, application context, pin-package information, and an explicit review of drop-in replacement availability. It distinguishes documented electrical capabilities from specifications that must be confirmed in the manufacturer datasheet, helping engineers make sourcing and circuit-design decisions without obscuring unresolved technical details.

جایگزین‌های drop-in برای SN75140P — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

هیچ جایگزین مستقیمی برای این محصول موجود نیست.

درخواست جایگزین

SN75140P مشخصات

Device Type Dual single-ended line receiver
Number of Receiver Channels 2 channels
ولتاژ تغذیه 5 V
Input Sensitivity ±100 mV
Input Current <100 uA
Reference Voltage Range 1.5 V to 3.5 V
Output Compatibility TTL-compatible
Strobe Compatibility TTL-compatible
محدوده دمای کاری 0°C to 70°C
بسته‌بندی 8-pin PDIP
نوع نصب Through-hole
Reference Control Common reference-voltage pin
Strobe Control Common strobe
Primary Application Party-line data-bus systems
Additional Functions Gated oscillator and level comparator

راهنمای پیکربندی پین SN75140P 8-pin pdip

پیکربندی پین برای SN75140P (پکیج 8-pin pdip). شماره‌گذاری پایه‌ها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعمل‌های لحیم‌کاری به آن مراجعه کنید.

نمودار پین‌آوت پکیج 8-pin pdip برای SN75140P

داده پین‌آوت تفصیلی موجود نیست برای SN75140P.

به دیتاشیت برای پیکربندی کامل پین‌ها.

کاربردهای معمول

SN75140P مناسب است برای 6 کاربردs: Party-Line Data Bus, Industrial Control Data Interface, Peripheral Data Link, Data Acquisition and Instrumentation, Legacy Communications Equipment, Gated Oscillator and Level Comparator.

🌐

Party-Line Data Bus

The SN75140P fits a shared data-bus receiver because its input current is less than 100 uA and its common reference voltage can be adjusted from 1.5 V to 3.5 V. Two single-ended channels share one threshold and one strobe, simplifying system control while preserving TTL-compatible outputs. The threshold should be set from measured bus noise and signal amplitude so that valid transitions retain adequate margin. Because party-line operation connects multiple nodes, engineers should also verify fanout, stub loading, fault behavior, and timing across the complete network rather than treating the receiver as an isolated logic gate.

🏭

Industrial Control Data Interface

The SN75140P can condition small single-ended signals in an industrial control interface when a 5 V TTL-compatible output is required. Its ±100 mV sensitivity recognizes small signal changes, while the adjustable 1.5 V to 3.5 V reference permits threshold tuning around the signal present at the receiver. Place the receiver at the end of the line and account for propagation delay when designing the handshake or strobe timing. The shared reference also makes both channels convenient for paired status or data signals, although industrial temperature-range and compliance requirements should be checked separately for the finished system.

🖥️

Peripheral Data Link

Use the SN75140P to recover TTL-level data from a peripheral line when the received amplitude is small and the logic threshold must be configurable. The dual receiver provides two channels in one 8-pin PDIP, reducing board area compared with separate single-channel parts. Its common strobe can support coordinated data qualification, while the common reference voltage simplifies threshold configuration across the pair. Validate the receiver's timing against the peripheral protocol and the line-driver characteristics, particularly when the cable introduces attenuation, reflections, or a measurable delay between transmitted and recovered data.

📡

Data Acquisition and Instrumentation

The SN75140P can serve as a thresholded interface in instrumentation that accepts small single-ended sensor or control signals. The externally adjustable 1.5 V to 3.5 V reference allows the system to select a decision level suited to its signal distribution, and the ±100 mV sensitivity supports detection of relatively small changes. Its outputs are TTL-compatible, which simplifies connection to legacy digital acquisition equipment. Engineers should verify that the sensor source can drive the input capacitance and reference network, and should evaluate noise margin, input bias effects, and acquisition timing before treating the recovered output as a precision measurement.

📻

Legacy Communications Equipment

The SN75140P is suitable for legacy communications equipment that combines a single 5 V supply, TTL-compatible logic, and a dual line receiver. Its two channels, common threshold, and common strobe provide a compact implementation for paired receive functions. The adjustable reference voltage is particularly useful when a fixed receiver threshold does not provide sufficient margin on an older cable system. Confirm pin assignments and timing in the Texas Instruments datasheet before substituting it into an existing board, and verify the receiver's behavior in the actual line environment rather than relying only on nominal input sensitivity.

🔧

Gated Oscillator and Level Comparator

Beyond its normal line-receiver role, the SN75140P can be configured as a gated oscillator or level comparator. The common reference input establishes the switching level, and the TTL-compatible strobe provides control over the output state. These functions can support simple event detection, pulse generation, or threshold-based control where a dedicated comparator or oscillator would be unnecessary. The external reference network must remain within the 1.5 V to 3.5 V range, and the design should account for input offset, noise around the threshold, propagation delay, and output loading. Confirm stable operation over the intended signal and temperature range.

خلاصه محصولات پیشنهادی

SN75453B Compatible 5 V dual bus transceiver driver استفاده‌شده در: Party-Line Data Bus, Industrial Control Data Interface, Peripheral Data Link, Data Acquisition and Instrumentation, Legacy Communications Equipment, Gated Oscillator and Level Comparator SN75140P Texas Instruments استفاده‌شده در: Party-Line Data Bus, Industrial Control Data Interface, Peripheral Data Link, Data Acquisition and Instrumentation, Legacy Communications Equipment, Gated Oscillator and Level Comparator
What is the SN75140P?
The SN75140P is a Texas Instruments dual single-ended line receiver with TTL-compatible outputs and strobes. It operates from a single 5 V supply and receives two channels in an 8-pin PDIP package. According to the manufacturer datasheet, it can also operate as a gated oscillator or level comparator, making it suitable for party-line, data-bus, and general-purpose communications interfaces.
What is the input sensitivity of SN75140P?
The SN75140P has a stated input sensitivity of ±100 mV. According to the Texas Instruments manufacturer datasheet, this allows the receiver to detect relatively small signal variations around its externally applied switching threshold. The exact relationship between input voltage, threshold voltage, and output state should be confirmed from the receiver's transfer characteristics for the selected operating conditions.
How is the SN75140P reference voltage adjusted?
The SN75140P uses one common reference-voltage input that can be adjusted from 1.5 V to 3.5 V. According to the Texas Instruments manufacturer datasheet, this adjustment allows the switching threshold to be optimized for the noise immunity of a particular system. Because both receiver channels share the reference pin, they normally operate with the same switching threshold.
Where can I download the SN75140P datasheet PDF?
The official SN75140P datasheet is available from Texas Instruments through the manufacturer's product page and direct datasheet link. The listed documentation is the Dual Line Receivers datasheet, Rev. C. Use that document to verify the complete pin description, electrical limits, timing characteristics, and recommended operating conditions before finalizing a circuit.
Where can I find the SN75140P pinout?
The SN75140P pin assignment is shown in the pin-description section of the Texas Instruments manufacturer datasheet. It is packaged in an 8-pin PDIP, and its architecture includes two receiver inputs, two outputs, a common reference input, a common strobe, supply connections, and ground. Use the manufacturer pin table when assigning PCB tracks and checking polarity.
Can the SN75140P replace SN75453B?
No—the SN75140P is the receiver half of a communications pair and should not replace the SN75453B driver in the same position. The Texas Instruments documentation identifies the SN75453B as the driver and the SN75140 as the receiver, with both devices operating from one 5 V supply. A transmitter location instead requires a compatible line driver.
What is the difference between a line receiver and a line driver?
A line receiver converts a small signal arriving from a transmission line into a valid logic-level output, while a line driver converts a logic input into a suitable signal for transmission. The SN75140P is a dual receiver and the SN75453B is the corresponding driver family identified by Texas Instruments. A complete communications link normally uses both functional roles.
When should I choose the SN75140P over a fixed-threshold receiver?
Choose the SN75140P when a shared, adjustable threshold gives better control over noise immunity or signal detection. Its common reference input spans 1.5 V to 3.5 V and is shared by both channels. A fixed-threshold receiver is simpler when the system noise environment is already well characterized and no threshold tuning is required.
Is the SN75140P suitable for a party-line data bus?
Yes—the SN75140P is specifically suited to party-line data-bus systems. Texas Instruments identifies an input current below 100 uA as a key suitability criterion, while the two receiver channels, common reference voltage, and common strobe simplify implementation of shared buses. Signal loading and system timing still require analysis for every attached node.
What is the best drop-in replacement for SN75140P?
No drop-in replacement can be confirmed from the available manufacturer and distributor information. A valid replacement must use the same 8-pin PDIP footprint, maintain pin-to-pin signal and control assignments, provide compatible 5 V operation, and preserve the required threshold and timing characteristics. Use the Request a Quote form on this page to discuss sourcing support for the original MPN.
What can replace the SN75140P?
A confirmed replacement for the SN75140P has not been identified with enough pin-level detail to claim drop-in compatibility. Any candidate must match the 8-pin PDIP footprint and provide equivalent receiver inputs, TTL-compatible outputs, common strobe behavior, and an adjustable reference range. Avoid selecting a replacement solely from broad line-receiver descriptions.
SN75140P versus a fixed-reference receiver: which is better for noisy bus systems?
The SN75140P is generally better when threshold adjustment is needed because its common reference voltage can be set from 1.5 V to 3.5 V. A fixed-reference receiver can be simpler and may reduce external adjustment circuitry. The correct comparison depends on measured bus noise, signal amplitude, propagation delay, and the logic thresholds used by the receiving system.
Where can I buy SN75140P online?
The SN75140P can be requested through the Request a Quote form on this page. The form is the appropriate route for current commercial availability, volume pricing, and lead-time confirmation. Engineers should identify the required package variant, operating temperature range, and production quantity before requesting a quotation.
What is the price of SN75140P?
The current SN75140P price depends on order quantity, packaging, and market conditions, so a static price should not be used for budgeting. Submit the required quantity and part details through the Request a Quote form on this page for a current quotation. This page does not publish a price figure that could become stale after verification.
What is the lead time for SN75140P?
Current lead time depends on supplier inventory, manufacturing status, order quantity, and the selected shipment destination. Use the Request a Quote form on this page to request a lead-time commitment for the SN75140P. For production planning, include the required delivery date and acceptable packaging details in the request.
Is SN75140P in stock?
Stock for SN75140P changes with order volume and supplier replenishment, so inventory should be confirmed at the time of quotation. Use the Request a Quote form on this page to request current availability for the exact Texas Instruments MPN. Include your required quantity and target shipment date to obtain a useful response.
How does the common strobe affect a dual receiver design?
The SN75140P uses a common strobe for its two receiver channels, reducing the number of control signals required in a dual-channel interface. The Texas Instruments manufacturer datasheet identifies the strobes and outputs as TTL-compatible. Determine whether simultaneous gating of both channels satisfies the system's data-valid timing before using the common control in a new design.
What are the key specifications of SN75140P that engineers should know?
The principal SN75140P specifications are dual single-ended receiver channels, 5 V single-supply operation, ±100 mV input sensitivity, input current below 100 uA, and an externally adjustable common reference from 1.5 V to 3.5 V. According to the Texas Instruments manufacturer datasheet, the device uses TTL-compatible outputs and strobes and is characterized from 0°C to 70°C.

داده‌های مرجع مهندسی برای SN75140P — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose the SN75140P when the design needs two single-ended receive channels, a single 5 V supply, TTL-compatible outputs, and an adjustable threshold shared by both channels. It is particularly suitable for party-line data buses, paired peripheral links, and communications equipment in which the received signal is small or the bus noise margin requires tuning. Select a fixed-threshold receiver instead when the system threshold is already well characterized and simplicity is more important than adjustment flexibility. Use the SN75453B as the transmit-side companion rather than as a receiver substitute. Before choosing another device as a replacement, require the same 8-pin PDIP footprint, pin-to-pin assignments, 5 V operation, compatible threshold range, and acceptable propagation timing. No drop-in alternative is listed because the available cross-reference results do not provide enough manufacturer-level pin and parameter information to support that claim.

مقایسه با جایگزین‌ها

پارامتر این محصول
Brand Texas Instruments
Package 8-pin PDIP
Receiver Configuration Dual single-ended line receiver
Supply Voltage 5 V
Input Sensitivity ±100 mV
Input Current <100 uA
Reference Voltage Range 1.5 V to 3.5 V
Output Compatibility TTL-compatible
Operating Temperature Range 0°C to 70°C
Strobe Configuration Common TTL-compatible strobe

تفاوت‌های کلیدی

  • Externally adjustable common threshold (در مقابلFixed-threshold dual line receivers)
  • Low loading for shared bus systems (در مقابلGeneral-purpose single-ended input comparators)
  • Dual receiver with shared control (در مقابلTwo discrete single-channel receiver ICs)

یادداشت‌های طراحی

Do not assume that the SN75140P and SN75453B are interchangeable: one is the receiver and the other is the driver. Verify the direction of every bus signal, the common reference connection, and the strobe polarity in the manufacturer pin table. When adapting an existing board, also confirm that the alternative's pin assignments and electrical limits match before treating it as a replacement.

Set the common reference voltage from measured signal levels and system noise rather than from a nominal midpoint alone. The documented adjustment range is 1.5 V to 3.5 V, and both channels share this threshold. Validate the selected value with worst-case input amplitude, line attenuation, receiver input current, and logic noise margin so that normal transitions do not approach the switching boundary.

Route the two receiver inputs away from switching-node and high-current return paths, and keep the common reference connection short to minimize pickup of external noise. Because both channels share the reference and strobe pins, noise on those routes affects both outputs. Use a stable reference network with an appropriate bypass path and place it near the receiver when the wiring is sensitive or the cable run is long.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

The manufacturer product page and datasheet listing do not state the requested environmental-compliance details in the available product information.

تاریخ تأیید داده‌ها: 2026-11-09 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

SN75140P datasheet SN75140P datasheet pdf SN75140P pinout SN75140P schematic SN75140P equivalent SN75140P replacement SN75140P cross reference SN75140P price SN75140P stock Texas Instruments SN75140P SN75140P PDIP pinout SN75140P party line receiver

قطعات و اصطلاحات مرتبط

Texas Instruments SN75140P SN75140 SN75453B dual line receiver single-ended line receiver interface IC communications IC semiconductor TTL 5 V power supply ±100 mV input sensitivity <100 uA input current 1.5 V to 3.5 V reference voltage switching threshold party-line data bus common strobe gated oscillator level comparator 8-pin PDIP DIP package through-hole package 0°C to 70°C operating range noise immunity
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ