SN75140P Dual Line Receiver, 5V | Texas Instruments
MPN: SN75140P ✓ 啟用中SN75140P 概覽
A dual line receiver is an interface integrated circuit that converts small differential or single-ended signals received over a cable or bus into logic-level outputs. In the broader semiconductor hierarchy, it belongs to interface ICs and performs the receiver function within a communications link. A line receiver complements a line driver: the driver places a signal onto the transmission line, while the receiver restores that signal to a valid logic level for the connected digital system.
The SN75140P supports a common reference voltage adjustable from 1.5 V to 3.5 V, allowing the switching threshold to be optimized for noise immunity in a particular system. Its ±100 mV input sensitivity enables recognition of small signals, while the low input current of less than 100 uA suits shared party-line arrangements. The two channels share one reference-voltage pin and one strobe input, reducing control overhead in a dual-channel bus interface.
TTL-compatible outputs and strobes allow the receiver to operate with conventional TTL logic. The device can also be used as a single-ended line receiver, a gated oscillator, or a level comparator. These functions make the same hardware applicable to data acquisition, bus monitoring, communications equipment, and systems in which a variable threshold is preferable to a fixed internal reference.
Typical applications include multipoint data buses, industrial control interfaces, peripheral data links, instrumentation interfaces, and legacy computer equipment. When the SN75140P is used with a compatible line driver such as the SN75453B, both devices can operate from one 5 V supply and occupy approximately the space of one 16-pin package. The SN75140P is characterized for operation from 0°C to 70°C.
The most important design consideration is threshold selection. Set the common reference voltage according to the signal amplitude, noise environment, and logic thresholds of the receiving system. Because the receiver uses a shared reference input, both channels normally use the same switching threshold. Account for propagation delay and ensure that the selected threshold preserves valid data timing across the complete bus operating range.
This page combines the manufacturer's device description with practical interface guidance, application context, pin-package information, and an explicit review of drop-in replacement availability. It distinguishes documented electrical capabilities from specifications that must be confirmed in the manufacturer datasheet, helping engineers make sourcing and circuit-design decisions without obscuring unresolved technical details.
直接替換替代品,適用於 SN75140P — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此產品無可直接替換的替代品。
申請替代品SN75140P 規格
| Device Type | Dual single-ended line receiver |
| Number of Receiver Channels | 2 channels |
| 供應電壓 | 5 V |
| Input Sensitivity | ±100 mV |
| Input Current | <100 uA |
| Reference Voltage Range | 1.5 V to 3.5 V |
| Output Compatibility | TTL-compatible |
| Strobe Compatibility | TTL-compatible |
| 工作溫度範圍 | 0°C to 70°C |
| 封裝 | 8-pin PDIP |
| 安裝類型 | Through-hole |
| Reference Control | Common reference-voltage pin |
| Strobe Control | Common strobe |
| Primary Application | Party-line data-bus systems |
| Additional Functions | Gated oscillator and level comparator |
SN75140P 8-pin pdip 腳位配置指南
SN75140P(8-pin pdip 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: SN75140P.
請參閱 資料表 以查看完整腳位配置。
典型應用
SN75140P 適用於 6 應用s: Party-Line Data Bus, Industrial Control Data Interface, Peripheral Data Link, Data Acquisition and Instrumentation, Legacy Communications Equipment, Gated Oscillator and Level Comparator.
Party-Line Data Bus
The SN75140P fits a shared data-bus receiver because its input current is less than 100 uA and its common reference voltage can be adjusted from 1.5 V to 3.5 V. Two single-ended channels share one threshold and one strobe, simplifying system control while preserving TTL-compatible outputs. The threshold should be set from measured bus noise and signal amplitude so that valid transitions retain adequate margin. Because party-line operation connects multiple nodes, engineers should also verify fanout, stub loading, fault behavior, and timing across the complete network rather than treating the receiver as an isolated logic gate.
推薦
Industrial Control Data Interface
The SN75140P can condition small single-ended signals in an industrial control interface when a 5 V TTL-compatible output is required. Its ±100 mV sensitivity recognizes small signal changes, while the adjustable 1.5 V to 3.5 V reference permits threshold tuning around the signal present at the receiver. Place the receiver at the end of the line and account for propagation delay when designing the handshake or strobe timing. The shared reference also makes both channels convenient for paired status or data signals, although industrial temperature-range and compliance requirements should be checked separately for the finished system.
推薦
Peripheral Data Link
Use the SN75140P to recover TTL-level data from a peripheral line when the received amplitude is small and the logic threshold must be configurable. The dual receiver provides two channels in one 8-pin PDIP, reducing board area compared with separate single-channel parts. Its common strobe can support coordinated data qualification, while the common reference voltage simplifies threshold configuration across the pair. Validate the receiver's timing against the peripheral protocol and the line-driver characteristics, particularly when the cable introduces attenuation, reflections, or a measurable delay between transmitted and recovered data.
推薦
Data Acquisition and Instrumentation
The SN75140P can serve as a thresholded interface in instrumentation that accepts small single-ended sensor or control signals. The externally adjustable 1.5 V to 3.5 V reference allows the system to select a decision level suited to its signal distribution, and the ±100 mV sensitivity supports detection of relatively small changes. Its outputs are TTL-compatible, which simplifies connection to legacy digital acquisition equipment. Engineers should verify that the sensor source can drive the input capacitance and reference network, and should evaluate noise margin, input bias effects, and acquisition timing before treating the recovered output as a precision measurement.
推薦
Legacy Communications Equipment
The SN75140P is suitable for legacy communications equipment that combines a single 5 V supply, TTL-compatible logic, and a dual line receiver. Its two channels, common threshold, and common strobe provide a compact implementation for paired receive functions. The adjustable reference voltage is particularly useful when a fixed receiver threshold does not provide sufficient margin on an older cable system. Confirm pin assignments and timing in the Texas Instruments datasheet before substituting it into an existing board, and verify the receiver's behavior in the actual line environment rather than relying only on nominal input sensitivity.
推薦
Gated Oscillator and Level Comparator
Beyond its normal line-receiver role, the SN75140P can be configured as a gated oscillator or level comparator. The common reference input establishes the switching level, and the TTL-compatible strobe provides control over the output state. These functions can support simple event detection, pulse generation, or threshold-based control where a dedicated comparator or oscillator would be unnecessary. The external reference network must remain within the 1.5 V to 3.5 V range, and the design should account for input offset, noise around the threshold, propagation delay, and output loading. Confirm stable operation over the intended signal and temperature range.
推薦
推薦產品摘要
工程參考資料,適用於 SN75140P — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 |
|---|---|
| Brand | Texas Instruments |
| Package | 8-pin PDIP |
| Receiver Configuration | Dual single-ended line receiver |
| Supply Voltage | 5 V |
| Input Sensitivity | ±100 mV |
| Input Current | <100 uA |
| Reference Voltage Range | 1.5 V to 3.5 V |
| Output Compatibility | TTL-compatible |
| Operating Temperature Range | 0°C to 70°C |
| Strobe Configuration | Common TTL-compatible strobe |
主要差異化特點
- Externally adjustable common threshold (對比Fixed-threshold dual line receivers)
- Low loading for shared bus systems (對比General-purpose single-ended input comparators)
- Dual receiver with shared control (對比Two discrete single-channel receiver ICs)
設計說明
Do not assume that the SN75140P and SN75453B are interchangeable: one is the receiver and the other is the driver. Verify the direction of every bus signal, the common reference connection, and the strobe polarity in the manufacturer pin table. When adapting an existing board, also confirm that the alternative's pin assignments and electrical limits match before treating it as a replacement.
Set the common reference voltage from measured signal levels and system noise rather than from a nominal midpoint alone. The documented adjustment range is 1.5 V to 3.5 V, and both channels share this threshold. Validate the selected value with worst-case input amplitude, line attenuation, receiver input current, and logic noise margin so that normal transitions do not approach the switching boundary.
Route the two receiver inputs away from switching-node and high-current return paths, and keep the common reference connection short to minimize pickup of external noise. Because both channels share the reference and strobe pins, noise on those routes affects both outputs. Use a stable reference network with an appropriate bypass path and place it near the receiver when the wiring is sensitive or the cable run is long.
合規資訊
The manufacturer product page and datasheet listing do not state the requested environmental-compliance details in the available product information.