SP3232EHET-L/TR - 3.3V 460kbps RS-232 | MaxLinear
MPN: SP3232EHET-L/TR ✓ NakahandaSP3232EHET-L/TR Ulas
An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 line levels and converts incoming RS-232 signals back into logic-compatible receiver outputs. The RS-232 transceiver category sits within serial interface ICs, interface ICs, and integrated circuits. It is commonly used to connect a host controller, embedded processor, test instrument, or industrial terminal to a longer-distance serial port where ground-referenced logic levels cannot drive the cable interface directly.
The SP3232EH family provides two transmit drivers and two receive channels, allowing one port to support bidirectional RS-232 communication. Operation from a 3V to 5.5V supply is useful in portable systems operating from a 3.3V rail, while the 460kbps signaling capability supports higher-speed serial links than legacy low-speed RS-232 implementations. Its enhanced 15kV human-body-model ESD rating is a notable protection feature for connector-facing circuits.
The architecture is optimized for portable and hand-held applications such as notebook and palmtop computers, where low supply voltage, compact packaging, and protection from electrostatic discharge are important. Because the device includes both directions of conversion, it can support two RS-232 lines without requiring separate driver and receiver ICs. The 16-SOIC package also provides a conventional surface-mount footprint compatible with automated assembly, although the exact pin assignment must be taken from the manufacturer pin-description table.
Typical applications include portable data-collection equipment, serial adapters, industrial service interfaces, diagnostic equipment, and embedded control systems that retain an RS-232 port. When one side of a cable is exposed to user contact or poorly controlled external wiring, the 15kV human-body-model ESD rating is especially relevant. Designers should still provide appropriate protection-network coordination and verify that the selected connector, cable, and grounding arrangement meet the system-level interface requirements.
The primary design consideration is power and signal integrity. Place the device close to the RS-232 connector so that board-trace exposure is minimized, connect the transceiver ground to the interface reference ground, and avoid long unprotected traces between the connector and IC. Confirm the 460kbps requirement against the actual cable length and noise environment because data rate, transmission distance, and capacitive loading are strongly related.
This product page consolidates the core electrical ratings, package information, interface use cases, verified drop-in candidates, comparison parameters, and practical layout guidance for faster component selection and PCB planning. Use the MaxLinear SP3232EH product page and manufacturer datasheet for the authoritative electrical characteristics, recommended application circuit, and exact pin configuration.
Mga alternatibo na pwedeng ilagay na SP3232EHET-L/TR — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok SP3232EHET-L/TR (parehas na form factor at footprint) — pagkakaiba sa Supply Voltage Range, Package, Charge-Pump Capacitor Requirement, Data Rate, Interface Standard.
SP3232EET-L/TR
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →SP3232EBEN-L/TR
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →LT1281ACSW#PBF
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
ST3232BDR
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →SP3232EHET-L/TR Mga Spesipikasyon
| Transceiver Configuration | 2 drivers / 2 receivers |
| Interface Standard | EIA/TIA-232-F |
| Supply Voltage Range | 3 V to 5.5 V |
| Minimum RS-232 Interoperability Supply | 2.7 V |
| Maximum Data Rate | 460 kbps |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| ESD Protection, Human Body Model | 15 kV |
| Packhaging | 16-SOIC |
| Package Width | 7.50 mm |
| Package Body Width | 0.295 inch |
| Uri ng Pagpapasok | Surface Mount |
| Packaging | Tube |
Gabay sa Pin Configuration ng SP3232EHET-L/TR 0.295 inch
Pin configuration para sa SP3232EHET-L/TR (0.295 inch package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa SP3232EHET-L/TR.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
SP3232EHET-L/TR ay nararapat para sa 6 aplikasyons: Portable RS-232 Data Collection, Industrial Serial Service Interface, Legacy Serial Adapter, Serial Diagnostic Equipment, Embedded Controller RS-232 Port, Instrumentation and Test Equipment.
Portable RS-232 Data Collection
The SP3232EHET-L/TR fits portable data-collection equipment that requires a wired RS-232 port while operating from a 3.3V system rail. Its two drivers and two receivers support bidirectional communication, while the 460kbps maximum rate accommodates compact protocols used with legacy peripherals. The 15kV human-body-model ESD protection is particularly valuable when the connector is exposed during field use. Place the transceiver close to the connector and use the device ground as the interface reference to minimize noise pickup on exposed traces.
Inirekomenda
Industrial Serial Service Interface
The SP3232EHET-L/TR can provide a robust service port on industrial test equipment, controllers, and diagnostic instruments. Two transmit drivers and two receive channels allow the equipment to exchange commands and status data with RS-232-compatible tools. Operation from 3V to 5.5V supports mixed-generation equipment, and the 460kbps rate provides useful protocol bandwidth. Confirm the device operating-temperature limit and the system ground strategy before deployment in an industrial enclosure.
Inirekomenda
Legacy Serial Adapter
The SP3232EHET-L/TR is suitable for a compact adapter that adds a legacy RS-232 port to a modern controller. Its 2/2 transceiver configuration supports both command transmission and response reception without requiring separate driver and receiver packages. The 3V minimum supply supports embedded 3.3V systems, while 5.5V compatibility covers conventional 5V designs. The 16-SOIC footprint simplifies assembly, although connector-side protection and board-level filtering should be designed around the maximum 460kbps signaling rate.
Inirekomenda
Serial Diagnostic Equipment
The SP3232EHET-L/TR can serve as the interface between a diagnostic instrument and a controller, modem, or service terminal. The two receiver channels are useful for systems that need more than one status or handshake input, while the two drivers support outbound command traffic. A 460kbps maximum data rate is suitable for many short-distance diagnostic protocols. For cable-connected equipment, maintain a common signal ground, minimize connector-to-IC routing, and verify that protocol timing remains reliable under the intended noise conditions.
Inirekomenda
Embedded Controller RS-232 Port
The SP3232EHET-L/TR allows an embedded controller to retain a wired RS-232 interface for configuration, programming, or field diagnostics. Its 3V to 5.5V operating range accommodates common embedded supply rails, and the compact 16-SOIC package supports board-space conservation. The transceiver converts digital controller signals to RS-232 levels and converts incoming line signals back to logic-compatible outputs. Place it near the connector and keep power and signal returns short to reduce susceptibility to external interference.
Inirekomenda
Instrumentation and Test Equipment
The SP3232EHET-L/TR is applicable to instrumentation that exchanges RS-232 commands with external test fixtures or laboratory computers. Its two drivers and two receivers support full interface communication at rates up to 460kbps, while operation from 3V to 5.5V allows use in both portable and mains-powered instruments. The 15kV human-body-model ESD rating improves interface resilience, but engineers should still evaluate cable length, grounding, isolation, and external protection according to the complete test environment.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for SP3232EHET-L/TR — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | SP3232EET-L/TR | SP3232EBEN-L/TR | LT1281ACSW#PBF | ST3232BDR |
|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | MaxLinear | MaxLinear | MaxLinear | Linear Technology | STMicroelectronics |
| Transceiver Configuration | 2 drivers / 2 receivers | 2 drivers / 2 receivers | 2 drivers / 2 receivers | 2 drivers / 2 receivers | 2 drivers / 2 receivers |
| Surface-Mount Package Pin Count | 16 pins | 16 pins | 16 pins | 16 pins | 16 pins |
Pangunahing mga Pagkakaiba
- Low-voltage RS-232 operation (kumpara saLT1281ACSW#PBF)
- Specified enhanced ESD protection (kumpara saSP3232EBEN-L/TR)
- High-speed 2/2 RS-232 channel configuration (kumpara saST3232BDR)
Talaan ng Disenyo
Place the SP3232EHET-L/TR close to the RS-232 connector and minimize the distance from connector pins to the corresponding transceiver pins. Keep the interface ground continuous and return it to the transceiver ground without narrow breaks. Longer exposed traces can act as antennas and increase susceptibility to electrostatic discharge and external interference, particularly when the equipment is connected through an unprotected cable.
Do not assume that matching the 16-SOIC package proves drop-in compatibility. Before substituting SP3232EET-L/TR, SP3232EBEN-L/TR, LT1281ACSW#PBF, or ST3232BDR, compare every pin name, supply range, driver and receiver count, shutdown behavior, enable polarity, and ESD rating. The target is specified for 3V to 5.5V operation, 460kbps, and 15kV human-body-model ESD protection.
Confirm that the intended cable length, capacitance, grounding arrangement, and electromagnetic environment can support the selected signaling rate. The device supports rates up to 460kbps, but that value is not a guarantee of error-free communication over every cable or installation. Use the manufacturer application guidance to determine whether external filtering or protection components are needed at the connector.
Route the transceiver supply from a stable local rail and maintain the recommended bypass capacitance at the power pins. Provide a low-impedance ground path so driver current returns do not share a noisy path with receiver or controller ground. When power is sourced from a higher-voltage rail, include the required regulator rather than applying voltage beyond the documented 5.5V maximum.
Impormasyon ng Pagsunod sa Kautusan
The device is an RS-232 interface IC rather than an automotive-qualified AEC-Q100 product. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer or current product documentation.