SP3232EHET-L/TR - 3.3V 460kbps RS-232 | MaxLinear
MPN: SP3232EHET-L/TR ✓ Hoạt độngSP3232EHET-L/TR Tóm tắt
An RS-232 transceiver is an interface IC that converts logic-level digital signals into RS-232 line levels and converts incoming RS-232 signals back into logic-compatible receiver outputs. The RS-232 transceiver category sits within serial interface ICs, interface ICs, and integrated circuits. It is commonly used to connect a host controller, embedded processor, test instrument, or industrial terminal to a longer-distance serial port where ground-referenced logic levels cannot drive the cable interface directly.
The SP3232EH family provides two transmit drivers and two receive channels, allowing one port to support bidirectional RS-232 communication. Operation from a 3V to 5.5V supply is useful in portable systems operating from a 3.3V rail, while the 460kbps signaling capability supports higher-speed serial links than legacy low-speed RS-232 implementations. Its enhanced 15kV human-body-model ESD rating is a notable protection feature for connector-facing circuits.
The architecture is optimized for portable and hand-held applications such as notebook and palmtop computers, where low supply voltage, compact packaging, and protection from electrostatic discharge are important. Because the device includes both directions of conversion, it can support two RS-232 lines without requiring separate driver and receiver ICs. The 16-SOIC package also provides a conventional surface-mount footprint compatible with automated assembly, although the exact pin assignment must be taken from the manufacturer pin-description table.
Typical applications include portable data-collection equipment, serial adapters, industrial service interfaces, diagnostic equipment, and embedded control systems that retain an RS-232 port. When one side of a cable is exposed to user contact or poorly controlled external wiring, the 15kV human-body-model ESD rating is especially relevant. Designers should still provide appropriate protection-network coordination and verify that the selected connector, cable, and grounding arrangement meet the system-level interface requirements.
The primary design consideration is power and signal integrity. Place the device close to the RS-232 connector so that board-trace exposure is minimized, connect the transceiver ground to the interface reference ground, and avoid long unprotected traces between the connector and IC. Confirm the 460kbps requirement against the actual cable length and noise environment because data rate, transmission distance, and capacitive loading are strongly related.
This product page consolidates the core electrical ratings, package information, interface use cases, verified drop-in candidates, comparison parameters, and practical layout guidance for faster component selection and PCB planning. Use the MaxLinear SP3232EH product page and manufacturer datasheet for the authoritative electrical characteristics, recommended application circuit, and exact pin configuration.
Bộ thay thế dễ dàng lắp đặt cho SP3232EHET-L/TR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với SP3232EHET-L/TR (cùng hình factor và footprint) — khác nhau ở Supply Voltage Range, Package, Charge-Pump Capacitor Requirement, Data Rate, Interface Standard.
SP3232EET-L/TR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →SP3232EBEN-L/TR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LT1281ACSW#PBF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ST3232BDR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →SP3232EHET-L/TR Thông số kỹ thuật
| Transceiver Configuration | 2 drivers / 2 receivers |
| Interface Standard | EIA/TIA-232-F |
| Supply Voltage Range | 3 V to 5.5 V |
| Minimum RS-232 Interoperability Supply | 2.7 V |
| Maximum Data Rate | 460 kbps |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| ESD Protection, Human Body Model | 15 kV |
| Hộp | 16-SOIC |
| Package Width | 7.50 mm |
| Package Body Width | 0.295 inch |
| Kiểu lắp đặt | Surface Mount |
| Packaging | Tube |
Hướng dẫn cấu hình chân SP3232EHET-L/TR 0.295 inch
Cấu hình chân cho SP3232EHET-L/TR (0.295 inch gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho SP3232EHET-L/TR.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
SP3232EHET-L/TR phù hợp cho 6 Áp dụngs: Portable RS-232 Data Collection, Industrial Serial Service Interface, Legacy Serial Adapter, Serial Diagnostic Equipment, Embedded Controller RS-232 Port, Instrumentation and Test Equipment.
Portable RS-232 Data Collection
The SP3232EHET-L/TR fits portable data-collection equipment that requires a wired RS-232 port while operating from a 3.3V system rail. Its two drivers and two receivers support bidirectional communication, while the 460kbps maximum rate accommodates compact protocols used with legacy peripherals. The 15kV human-body-model ESD protection is particularly valuable when the connector is exposed during field use. Place the transceiver close to the connector and use the device ground as the interface reference to minimize noise pickup on exposed traces.
Được đề xuất
Industrial Serial Service Interface
The SP3232EHET-L/TR can provide a robust service port on industrial test equipment, controllers, and diagnostic instruments. Two transmit drivers and two receive channels allow the equipment to exchange commands and status data with RS-232-compatible tools. Operation from 3V to 5.5V supports mixed-generation equipment, and the 460kbps rate provides useful protocol bandwidth. Confirm the device operating-temperature limit and the system ground strategy before deployment in an industrial enclosure.
Được đề xuất
Legacy Serial Adapter
The SP3232EHET-L/TR is suitable for a compact adapter that adds a legacy RS-232 port to a modern controller. Its 2/2 transceiver configuration supports both command transmission and response reception without requiring separate driver and receiver packages. The 3V minimum supply supports embedded 3.3V systems, while 5.5V compatibility covers conventional 5V designs. The 16-SOIC footprint simplifies assembly, although connector-side protection and board-level filtering should be designed around the maximum 460kbps signaling rate.
Được đề xuất
Serial Diagnostic Equipment
The SP3232EHET-L/TR can serve as the interface between a diagnostic instrument and a controller, modem, or service terminal. The two receiver channels are useful for systems that need more than one status or handshake input, while the two drivers support outbound command traffic. A 460kbps maximum data rate is suitable for many short-distance diagnostic protocols. For cable-connected equipment, maintain a common signal ground, minimize connector-to-IC routing, and verify that protocol timing remains reliable under the intended noise conditions.
Được đề xuất
Embedded Controller RS-232 Port
The SP3232EHET-L/TR allows an embedded controller to retain a wired RS-232 interface for configuration, programming, or field diagnostics. Its 3V to 5.5V operating range accommodates common embedded supply rails, and the compact 16-SOIC package supports board-space conservation. The transceiver converts digital controller signals to RS-232 levels and converts incoming line signals back to logic-compatible outputs. Place it near the connector and keep power and signal returns short to reduce susceptibility to external interference.
Được đề xuất
Instrumentation and Test Equipment
The SP3232EHET-L/TR is applicable to instrumentation that exchanges RS-232 commands with external test fixtures or laboratory computers. Its two drivers and two receivers support full interface communication at rates up to 460kbps, while operation from 3V to 5.5V allows use in both portable and mains-powered instruments. The 15kV human-body-model ESD rating improves interface resilience, but engineers should still evaluate cable length, grounding, isolation, and external protection according to the complete test environment.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho SP3232EHET-L/TR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | SP3232EET-L/TR | SP3232EBEN-L/TR | LT1281ACSW#PBF | ST3232BDR |
|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | MaxLinear | MaxLinear | MaxLinear | Linear Technology | STMicroelectronics |
| Transceiver Configuration | 2 drivers / 2 receivers | 2 drivers / 2 receivers | 2 drivers / 2 receivers | 2 drivers / 2 receivers | 2 drivers / 2 receivers |
| Surface-Mount Package Pin Count | 16 pins | 16 pins | 16 pins | 16 pins | 16 pins |
Bảo phân biệt quan trọng
- Low-voltage RS-232 operation (vsLT1281ACSW#PBF)
- Specified enhanced ESD protection (vsSP3232EBEN-L/TR)
- High-speed 2/2 RS-232 channel configuration (vsST3232BDR)
Ghi chú thiết kế
Place the SP3232EHET-L/TR close to the RS-232 connector and minimize the distance from connector pins to the corresponding transceiver pins. Keep the interface ground continuous and return it to the transceiver ground without narrow breaks. Longer exposed traces can act as antennas and increase susceptibility to electrostatic discharge and external interference, particularly when the equipment is connected through an unprotected cable.
Do not assume that matching the 16-SOIC package proves drop-in compatibility. Before substituting SP3232EET-L/TR, SP3232EBEN-L/TR, LT1281ACSW#PBF, or ST3232BDR, compare every pin name, supply range, driver and receiver count, shutdown behavior, enable polarity, and ESD rating. The target is specified for 3V to 5.5V operation, 460kbps, and 15kV human-body-model ESD protection.
Confirm that the intended cable length, capacitance, grounding arrangement, and electromagnetic environment can support the selected signaling rate. The device supports rates up to 460kbps, but that value is not a guarantee of error-free communication over every cable or installation. Use the manufacturer application guidance to determine whether external filtering or protection components are needed at the connector.
Route the transceiver supply from a stable local rail and maintain the recommended bypass capacitance at the power pins. Provide a low-impedance ground path so driver current returns do not share a noisy path with receiver or controller ground. When power is sourced from a higher-voltage rail, include the required regulator rather than applying voltage beyond the documented 5.5V maximum.
Thông tin tuân thủ
The device is an RS-232 interface IC rather than an automotive-qualified AEC-Q100 product. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the manufacturer or current product documentation.