STM8L101F2U6TR - 16MHz 4KB Flash Ultra-Low-Power MCU | STMicroelectronics
MPN: STM8L101F2U6TR ✓ NakahandaSTM8L101F2U6TR Ulas
An ultra-low-power microcontroller is a type of embedded controller that minimizes energy use during idle, wait, and active-halt operating modes. The STM8L101 family belongs to the STM8L EnergyLite line of 8-bit microcontrollers, combining a compact architecture with low-power modes for applications such as wireless controls, sensor nodes, compact consumer equipment, and battery-powered accessories. The STM8L101F2U6TR operating voltage range is 1.65 V to 3.6 V, allowing operation from low-voltage energy-harvesting or single-cell-derived power rails when the rail regulation characteristics are suitable.
The STM8L101F2U6TR provides 4 KB of Flash program memory, an 8-bit instruction set, and a maximum clock speed of 16 MHz. The family also provides low-power operating characteristics, including Halt current of 0.3 µA and Active-halt current listed from 0.8 µA in the STM8L101x2 family documentation. Its communication resources include USART, SPI, and I2C, while multifunction timers and comparators support sensing, motor-control, and timing tasks without requiring additional discrete components.
The 20-pin UFQFPN package is only 3 mm by 3 mm with a stated height of 0.60 mm. This small footprint supports space-constrained designs, but exposed-pad thermal management and assembly process controls require attention. The 18 available I/O ports give designers access to digital interfaces, timers, serial functions, and analog comparator features in a modest pin count. The manufacturer family page identifies the STM8L101x2 as an active low-power MCU family with performance up to 16 MIPS at 16 MHz.
Typical uses for this part include low-power sensor interfaces, remote controls, battery-powered monitors, small serial-connected accessories, and embedded control blocks in compact consumer products. Its I2C and SPI interfaces allow connection to sensors and external transceivers, while USART provides a simple path to host controllers or service interfaces. The comparators and timers are useful for threshold detection, wake-up logic, and low-power event sequencing.
When laying out this device, place decoupling capacitors close to the supply and ground pins, route sensitive analog inputs away from switching nodes, and consult the pin-description and package-land-pattern sections of the manufacturer datasheet before assigning PCB tracks. This page combines the manufacturer family specifications with practical application guidance, alternative-selection notes, and interface-oriented design considerations for engineers evaluating the STM8L101F2U6TR.
Mga alternatibo na pwedeng ilagay na STM8L101F2U6TR — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
STM8L101F2U6ATR
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
STM8L101F2U6A
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
STM8L101F2U6
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
STM8L101F2U6TR Mga Pinakamataas na Rating at Electrical Characteristics
| Product Type | 8-bit ultra-low-power microcontroller |
| Series | STM8L EnergyLite |
| Maksimum na Taktiko ng Oras | 16 MHz |
| Maximum Processing Performance | 16 MIPS at 16 MHz |
| Flash Memory | 4 KB (4K x 8) |
| Supply Voltage Range | 1.65 V to 3.6 V |
| I/O Ports | 18 |
| Packhaging | 20-pin UFQFPN, 3 mm x 3 mm, 0.60 mm height |
| Uri ng Pagpapasok | Surface Mount |
| Halt Current | 0.3 µA |
| Active-Halt Current | 0.8 µA or higher, depending on operating condition |
| Serial Interfaces | USART, SPI, I2C |
| Peripheral Support | Multifunction timers and comparators |
| Hanay ng Temperature na Operasyon | -40 °C to +85 °C |
| Architecture | Enhanced STM8 8-bit CPU core |
| RoHS Compliance | Compliant |
| Katayuan ng Lifecycle | Active |
Gabay sa Pin Configuration ng STM8L101F2U6TR 20-pin ufqfpn, 3 mm x 3 mm, 0.60 mm height
Pin configuration para sa STM8L101F2U6TR (20-pin ufqfpn, 3 mm x 3 mm, 0.60 mm height package). Kasama sa digital IC na ito ang GPIO, mga communication interface (UART, SPI, I2C), at mga power pin. Sumangguni sa datasheet ng manufacturer para sa mga alternatibong function ng pin at mga opsyon sa configuration. Mahalaga para sa disenyo ng embedded system at PCB layout.
Wala ng detalyadong pinout data na magagamit para sa STM8L101F2U6TR.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
STM8L101F2U6TR ay nararapat para sa 6 aplikasyons: Battery-Powered Sensor Node, Wireless Remote Control, Compact Serial Monitoring Device, Battery-Powered Accessory Controller, Low-Power Threshold Detection, Small Industrial Control Module.
Battery-Powered Sensor Node
The STM8L101F2U6TR fits a compact sensor node that periodically wakes, measures a condition, and returns to a low-power state. Its 1.65 V to 3.6 V operating range supports low-voltage rails, while the 0.3 µA Halt current provides a useful starting point for battery-life calculations. I2C or SPI can connect digital sensors, and the comparators can perform threshold detection without waking the main processing path. Firmware should disable unused peripherals, select the lowest acceptable clock setting, and configure wake-up sources to achieve the intended duty cycle.
Inirekomenda
Wireless Remote Control
In a compact wireless remote, the STM8L101F2U6TR can scan buttons, drive indicator LEDs, and manage a serial radio connection without requiring a larger controller. Its 18 I/O ports provide ample capacity for switches and status signals within a 3 mm by 3 mm package. USART offers a straightforward link to many radio transceivers, while SPI or I2C can serve higher-throughput or bus-oriented accessories. Low-power operation and wake-up interrupt handling are especially important because the device spends most of its life waiting for user input.
Inirekomenda
Compact Serial Monitoring Device
The STM8L101F2U6TR is suitable for a small monitoring module that gathers local sensor information and forwards status over a serial link. The USART provides a simple host or service interface, while I2C and SPI expand the available device connections. Its 16 MHz enhanced STM8 core provides up to 16 MIPS for protocol handling, and the low-power modes support installations where continuous full-rate processing is unnecessary. Designers should define buffering and timeout behavior so communication activity does not prevent the controller from reaching its intended low-power state.
Inirekomenda
Battery-Powered Accessory Controller
For a wearable or compact consumer accessory, the STM8L101F2U6TR can manage buttons, status LEDs, charging-related control signals, and a short-range communications link. Its 3 mm by 3 mm UFQFPN package preserves board area in space-constrained products, and 18 I/O ports support both control and peripheral multiplexing. The 1.65 V minimum supply voltage is useful for compact power systems, although the complete battery, regulator, and load-switch arrangement must remain within the manufacturer electrical limits.
Inirekomenda
Low-Power Threshold Detection
The STM8L101F2U6TR can implement an always-available threshold-detection function using its integrated comparators and multifunction timers. A comparator can monitor a battery, sensor output, or control signal while the CPU remains in a low-power mode, reducing processing load and improving response time. The exact comparator and timer channels must be assigned from the manufacturer pin and peripheral tables. Firmware should configure the interrupt or wake-up path carefully to avoid nuisance wake-ups and unnecessary energy consumption.
Inirekomenda
Small Industrial Control Module
The STM8L101F2U6TR can serve as the local controller in a small industrial sensing module that interfaces to a parent system through USART. Its multifunction timers handle periodic sampling and output timing, while I2C or SPI connects to sensors, memory, or transceiver hardware. The -40 °C to +85 °C temperature range supports industrial environments when the board, power supply, and external components are appropriately rated. Use isolation, surge protection, and grounding practices at any interface that leaves the controlled enclosure.
Inirekomenda
Impormasyon ng Talumpati sa Engineering for STM8L101F2U6TR — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | STM8L101F2U6ATR | STM8L101F2U6A | STM8L101F2U6 |
|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 20-pin UFQFPN (3 mm x 3 mm) | 20-pin UFQFPN (3 mm x 3 mm) | 20-pin UFQFPN (3 mm x 3 mm) | 20-pin UFQFPN (3 mm x 3 mm) |
| Maximum Clock Frequency | 16 MHz | 16 MHz | 16 MHz | 16 MHz |
| Flash Memory | 4 KB | 4 KB | 4 KB | 4 KB |
| Supply Voltage Range | 1.65 V to 3.6 V | 1.65 V to 3.6 V | 1.65 V to 3.6 V | 1.65 V to 3.6 V |
| I/O Ports | 18 | 18 | 18 | 18 |
| Serial Interfaces | USART, SPI, I2C | USART, SPI, I2C | USART, SPI, I2C | USART, SPI, I2C |
| Halt Current | 0.3 µA | 0.3 µA | 0.3 µA | 0.3 µA |
Pangunahing mga Pagkakaiba
- Very compact 3 mm by 3 mm package with 18 I/O ports (kumpara saSTM8L101F2U6)
- Low-voltage operation with multiple low-power modes (kumpara saSTM8L101F2U6A)
- Complete connectivity for compact embedded products (kumpara saSTM8L101F2U6ATR)
Talaan ng Disenyo
Budget the complete sleep-mode current rather than the 0.3 µA Halt figure alone. Estimated: supply leakage, pull-up resistors, peripheral state, regulator quiescent current, and periodic wake-ups are added to the MCU contribution. Use the device's low-power modes as intended and remove external pull networks where they prevent the required operating state. Confirm the final battery-life calculation with measured current on the assembled product.
Place the supply bypass capacitor as close as practical to the device's power and ground connections, and follow the manufacturer decoupling recommendations in the application information. The 3 mm by 3 mm UFQFPN footprint is small, so component placement and the exposed-pad connection must be planned together. Validate the land pattern, paste volume, and reflow profile before releasing the PCB assembly drawings.
Assign pins from the manufacturer pin-description table because the 18 I/O ports provide alternate functions that can limit simultaneous peripheral use. Keep I2C and SPI routing short, provide a continuous ground reference, and position pull-up or termination networks near the relevant driver or receiver. Route exposed-pad thermal current into a low-impedance copper plane to avoid a local temperature rise during brief active processing.
Impormasyon ng Pagsunod sa Kautusan
The STM8L101F2U6TR listing identifies RoHS-compliant construction and an active lifecycle status. AEC-Q100 qualification, REACH status, lead-free construction, halogen-free construction, and conflict-minerals reporting were not confirmed.