STM8L101F2U6TR - 16MHz 4KB Flash Ultra-Low-Power MCU | STMicroelectronics
MPN: STM8L101F2U6TR ✓ 啟用中STM8L101F2U6TR 概覽
An ultra-low-power microcontroller is a type of embedded controller that minimizes energy use during idle, wait, and active-halt operating modes. The STM8L101 family belongs to the STM8L EnergyLite line of 8-bit microcontrollers, combining a compact architecture with low-power modes for applications such as wireless controls, sensor nodes, compact consumer equipment, and battery-powered accessories. The STM8L101F2U6TR operating voltage range is 1.65 V to 3.6 V, allowing operation from low-voltage energy-harvesting or single-cell-derived power rails when the rail regulation characteristics are suitable.
The STM8L101F2U6TR provides 4 KB of Flash program memory, an 8-bit instruction set, and a maximum clock speed of 16 MHz. The family also provides low-power operating characteristics, including Halt current of 0.3 µA and Active-halt current listed from 0.8 µA in the STM8L101x2 family documentation. Its communication resources include USART, SPI, and I2C, while multifunction timers and comparators support sensing, motor-control, and timing tasks without requiring additional discrete components.
The 20-pin UFQFPN package is only 3 mm by 3 mm with a stated height of 0.60 mm. This small footprint supports space-constrained designs, but exposed-pad thermal management and assembly process controls require attention. The 18 available I/O ports give designers access to digital interfaces, timers, serial functions, and analog comparator features in a modest pin count. The manufacturer family page identifies the STM8L101x2 as an active low-power MCU family with performance up to 16 MIPS at 16 MHz.
Typical uses for this part include low-power sensor interfaces, remote controls, battery-powered monitors, small serial-connected accessories, and embedded control blocks in compact consumer products. Its I2C and SPI interfaces allow connection to sensors and external transceivers, while USART provides a simple path to host controllers or service interfaces. The comparators and timers are useful for threshold detection, wake-up logic, and low-power event sequencing.
When laying out this device, place decoupling capacitors close to the supply and ground pins, route sensitive analog inputs away from switching nodes, and consult the pin-description and package-land-pattern sections of the manufacturer datasheet before assigning PCB tracks. This page combines the manufacturer family specifications with practical application guidance, alternative-selection notes, and interface-oriented design considerations for engineers evaluating the STM8L101F2U6TR.
直接替換替代品,適用於 STM8L101F2U6TR — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
STM8L101F2U6ATR
✅ 直接替換📋 參考替代品(不在目錄中)
STM8L101F2U6A
✅ 直接替換📋 參考替代品(不在目錄中)
STM8L101F2U6
✅ 直接替換📋 參考替代品(不在目錄中)
STM8L101F2U6TR 最大額定值與電氣特性
| Product Type | 8-bit ultra-low-power microcontroller |
| Series | STM8L EnergyLite |
| 最大時脈頻率 | 16 MHz |
| Maximum Processing Performance | 16 MIPS at 16 MHz |
| Flash Memory | 4 KB (4K x 8) |
| Supply Voltage Range | 1.65 V to 3.6 V |
| I/O Ports | 18 |
| 封裝 | 20-pin UFQFPN, 3 mm x 3 mm, 0.60 mm height |
| 安裝類型 | Surface Mount |
| Halt Current | 0.3 µA |
| Active-Halt Current | 0.8 µA or higher, depending on operating condition |
| Serial Interfaces | USART, SPI, I2C |
| Peripheral Support | Multifunction timers and comparators |
| 工作溫度範圍 | -40 °C to +85 °C |
| Architecture | Enhanced STM8 8-bit CPU core |
| RoHS Compliance | Compliant |
| 生命週期狀態 | Active |
STM8L101F2U6TR 20-pin ufqfpn, 3 mm x 3 mm, 0.60 mm height 腳位配置指南
STM8L101F2U6TR(20-pin ufqfpn, 3 mm x 3 mm, 0.60 mm height 封裝)的腳位配置。 此數位 IC 包含 GPIO、通訊介面(UART、SPI、I2C)與電源腳位。替代腳位功能與配置選項請參閱製造商資料表。對嵌入式系統設計與 PCB 佈局至關重要。
無詳細腳位定義資料: STM8L101F2U6TR.
請參閱 資料表 以查看完整腳位配置。
典型應用
STM8L101F2U6TR 適用於 6 應用s: Battery-Powered Sensor Node, Wireless Remote Control, Compact Serial Monitoring Device, Battery-Powered Accessory Controller, Low-Power Threshold Detection, Small Industrial Control Module.
Battery-Powered Sensor Node
The STM8L101F2U6TR fits a compact sensor node that periodically wakes, measures a condition, and returns to a low-power state. Its 1.65 V to 3.6 V operating range supports low-voltage rails, while the 0.3 µA Halt current provides a useful starting point for battery-life calculations. I2C or SPI can connect digital sensors, and the comparators can perform threshold detection without waking the main processing path. Firmware should disable unused peripherals, select the lowest acceptable clock setting, and configure wake-up sources to achieve the intended duty cycle.
推薦
Wireless Remote Control
In a compact wireless remote, the STM8L101F2U6TR can scan buttons, drive indicator LEDs, and manage a serial radio connection without requiring a larger controller. Its 18 I/O ports provide ample capacity for switches and status signals within a 3 mm by 3 mm package. USART offers a straightforward link to many radio transceivers, while SPI or I2C can serve higher-throughput or bus-oriented accessories. Low-power operation and wake-up interrupt handling are especially important because the device spends most of its life waiting for user input.
推薦
Compact Serial Monitoring Device
The STM8L101F2U6TR is suitable for a small monitoring module that gathers local sensor information and forwards status over a serial link. The USART provides a simple host or service interface, while I2C and SPI expand the available device connections. Its 16 MHz enhanced STM8 core provides up to 16 MIPS for protocol handling, and the low-power modes support installations where continuous full-rate processing is unnecessary. Designers should define buffering and timeout behavior so communication activity does not prevent the controller from reaching its intended low-power state.
推薦
Battery-Powered Accessory Controller
For a wearable or compact consumer accessory, the STM8L101F2U6TR can manage buttons, status LEDs, charging-related control signals, and a short-range communications link. Its 3 mm by 3 mm UFQFPN package preserves board area in space-constrained products, and 18 I/O ports support both control and peripheral multiplexing. The 1.65 V minimum supply voltage is useful for compact power systems, although the complete battery, regulator, and load-switch arrangement must remain within the manufacturer electrical limits.
推薦
Low-Power Threshold Detection
The STM8L101F2U6TR can implement an always-available threshold-detection function using its integrated comparators and multifunction timers. A comparator can monitor a battery, sensor output, or control signal while the CPU remains in a low-power mode, reducing processing load and improving response time. The exact comparator and timer channels must be assigned from the manufacturer pin and peripheral tables. Firmware should configure the interrupt or wake-up path carefully to avoid nuisance wake-ups and unnecessary energy consumption.
推薦
Small Industrial Control Module
The STM8L101F2U6TR can serve as the local controller in a small industrial sensing module that interfaces to a parent system through USART. Its multifunction timers handle periodic sampling and output timing, while I2C or SPI connects to sensors, memory, or transceiver hardware. The -40 °C to +85 °C temperature range supports industrial environments when the board, power supply, and external components are appropriately rated. Use isolation, surge protection, and grounding practices at any interface that leaves the controlled enclosure.
推薦
工程參考資料,適用於 STM8L101F2U6TR — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | STM8L101F2U6ATR | STM8L101F2U6A | STM8L101F2U6 |
|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 20-pin UFQFPN (3 mm x 3 mm) | 20-pin UFQFPN (3 mm x 3 mm) | 20-pin UFQFPN (3 mm x 3 mm) | 20-pin UFQFPN (3 mm x 3 mm) |
| Maximum Clock Frequency | 16 MHz | 16 MHz | 16 MHz | 16 MHz |
| Flash Memory | 4 KB | 4 KB | 4 KB | 4 KB |
| Supply Voltage Range | 1.65 V to 3.6 V | 1.65 V to 3.6 V | 1.65 V to 3.6 V | 1.65 V to 3.6 V |
| I/O Ports | 18 | 18 | 18 | 18 |
| Serial Interfaces | USART, SPI, I2C | USART, SPI, I2C | USART, SPI, I2C | USART, SPI, I2C |
| Halt Current | 0.3 µA | 0.3 µA | 0.3 µA | 0.3 µA |
主要差異化特點
- Very compact 3 mm by 3 mm package with 18 I/O ports (對比STM8L101F2U6)
- Low-voltage operation with multiple low-power modes (對比STM8L101F2U6A)
- Complete connectivity for compact embedded products (對比STM8L101F2U6ATR)
設計說明
Budget the complete sleep-mode current rather than the 0.3 µA Halt figure alone. Estimated: supply leakage, pull-up resistors, peripheral state, regulator quiescent current, and periodic wake-ups are added to the MCU contribution. Use the device's low-power modes as intended and remove external pull networks where they prevent the required operating state. Confirm the final battery-life calculation with measured current on the assembled product.
Place the supply bypass capacitor as close as practical to the device's power and ground connections, and follow the manufacturer decoupling recommendations in the application information. The 3 mm by 3 mm UFQFPN footprint is small, so component placement and the exposed-pad connection must be planned together. Validate the land pattern, paste volume, and reflow profile before releasing the PCB assembly drawings.
Assign pins from the manufacturer pin-description table because the 18 I/O ports provide alternate functions that can limit simultaneous peripheral use. Keep I2C and SPI routing short, provide a continuous ground reference, and position pull-up or termination networks near the relevant driver or receiver. Route exposed-pad thermal current into a low-impedance copper plane to avoid a local temperature rise during brief active processing.
合規資訊
The STM8L101F2U6TR listing identifies RoHS-compliant construction and an active lifecycle status. AEC-Q100 qualification, REACH status, lead-free construction, halogen-free construction, and conflict-minerals reporting were not confirmed.