TJA1041T/N1 - 1Mbit/s CAN Transceiver | NXP | SOIC-14
MPN: TJA1041T/N1 ✗ Tapus ng BuhayTJA1041T/N1 Ulas
A CAN transceiver is an interface IC within the automotive network-communication hierarchy. It translates the controller's logic-level TXD and RXD signals into a differential bus waveform for transmission and converts received differential bus levels into a logic signal for the controller. This physical-layer function complements the CAN protocol controller, which handles message identifiers, arbitration, error handling, and higher-level data exchange.
The TJA1041T/N1 provides differential transmit capability, differential receive capability, and compatibility with high-speed CAN protocol controllers operating up to 1 Mbit/s. Its single-transceiver arrangement suits conventional CAN nodes that do not require the additional transceiver features found in sleep-capable variants. The SOIC-14 package supports surface-mount assembly while providing separate pins for the bus interface, logic interface, ground connection, and stabilization.
Automotive and industrial CAN networks benefit from the robust differential signaling inherent in the TJA1041 architecture. Differential reception rejects common-mode voltage present on the bus, while the controller and transceiver can use twisted-pair wiring to maintain signal integrity over longer cable runs. The manufacturer's product documentation identifies the device primarily for automotive high-speed CAN applications and confirms compatibility with suitable CAN protocol controllers.
Typical deployments include engine-control units, transmission controllers, body-control modules, gateways, electronic control units, industrial automation controllers, and CAN-based sensor or actuator networks. In these systems, the TJA1041T/N1 handles the physical bus layer while a separate CAN controller manages frame arbitration, acknowledgments, error counters, and communication with the host processor.
Designers should follow the manufacturer's recommended transceiver and bus-line application circuit, including termination, common-mode choke or split-termination options where required, decoupling, and PCB routing guidance. The 1 Mbit/s capability does not remove the need for controlled bus topology, adequate ground references, correct termination placement, and protection suited to the vehicle or industrial environment.
This page combines the TJA1041T/N1 lifecycle information, verified source links, same-footprint alternatives, application guidance, and engineering design notes to support component selection, PCB planning, and long-term supply-risk assessment.
Mga alternatibo na pwedeng ilagay na TJA1041T/N1 — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok TJA1041T/N1 (parehas na form factor at footprint) — pagkakaiba sa Bus Interface, Package, Product Type.
TJA1041T/CM,118
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
TJA1050T/N1
✅ Drop-InMagkontak para sa presyo
Tingnan ang Datasheet →TJA1041T/N1 Mga Spesipikasyon
| Product Type | High-speed CAN transceiver |
| Supported Data Rate | Up to 1 Mbit/s |
| Transceiver Configuration | 1/1 half transceiver |
| Bus Interface | Differential CAN transmit and differential receive |
| Protocol Compatibility | Compatible with suitable high-speed CAN protocol controllers |
| Primary Application | Automotive high-speed CAN nodes |
| Packhaging | 14-SO |
| Style ng Pagpapasok | SMD/SMT |
| Manufacturer | NXP Semiconductors |
| Katayuan ng Lifecycle | End of Life |
| Supply Chain Status | Shipping discontinuance and replacement information available from NXP |
| Number of Transceivers | 1 |
| Interface Category | CAN interface IC |
Gabay sa Pin Configuration ng TJA1041T/N1 14-so
Pin configuration para sa TJA1041T/N1 (14-so package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa TJA1041T/N1.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
TJA1041T/N1 ay nararapat para sa 6 aplikasyons: Automotive Electronic Control Units, Body-Control Module Networks, Powertrain and Transmission Controllers, Industrial Automation CAN Gateways, CAN-Based Sensor and Actuator Networks, Vehicle Network Gateways.
Automotive Electronic Control Units
The TJA1041T/N1 fits an automotive electronic control unit that requires a high-speed CAN physical layer, because NXP identifies the device for automotive CAN nodes operating up to 1 Mbit/s. The IC sits between the CAN protocol controller and the differential bus, translating TXD into the bus waveform while converting received bus levels into RXD for the controller. Its 14-SO surface-mount package supports compact, automated PCB assembly. The design must follow the manufacturer's bus-line application circuit and account for automotive ESD exposure, ground reference, bus topology, and termination placement.
Inirekomenda
Body-Control Module Networks
The TJA1041T/N1 is appropriate for a body-control module that exchanges switch, lighting, door, and sensor data over a 1 Mbit/s CAN network. Its differential transmit and receive interface reduces susceptibility to common-mode noise found in vehicle wiring, while the separate CAN controller remains responsible for arbitration and error management. The SOIC-14 package allows placement on a conventional multilayer automotive PCB. Layout should minimize loop area around bus and ground paths, keep transceiver supply decoupling close to the device, and place the network termination at the physical bus endpoints.
Inirekomenda
Powertrain and Transmission Controllers
A transmission or powertrain controller can use the TJA1041T/N1 as the 1 Mbit/s physical interface between its CAN controller and vehicle network. Differential signaling supports reliable communication over twisted-pair harnesses, while the transceiver's dedicated transmit and receive functions separate bus drive from logic-level reception. Because this is an End-of-Life device, an automotive program should evaluate lifecycle continuity, approved-source availability, date-code control, and change notification before committing the part to a new platform. The PCB and bus implementation should follow the manufacturer's reference topology.
Inirekomenda
Industrial Automation CAN Gateways
The TJA1041T/N1 can provide the physical layer for an industrial CAN gateway that links sensors, drives, remote I/O, or factory controllers at up to 1 Mbit/s. Differential CAN communication is useful in environments where cable routing passes near motors, switching equipment, or other noise sources. The gateway still requires a separate CAN protocol controller, and the bus must be designed for its maximum length, node count, topology, and termination. Engineers should verify temperature and environmental requirements for the installed enclosure and consider the device's End-of-Life status when planning product longevity.
Inirekomenda
CAN-Based Sensor and Actuator Networks
The TJA1041T/N1 is suitable for a distributed node that connects a sensor or actuator to a 1 Mbit/s CAN backbone. The controller can originate periodic measurement frames, while the TJA1041 provides the differential physical signaling required across the wiring harness. In a multi-node installation, correct termination and topology are as important as transceiver speed because reflections and excessive cable length can impair bit timing. The 14-SO footprint simplifies conventional surface-mount assembly, although the circuit should include the supply and bus-network components specified in the manufacturer's application guidance.
Inirekomenda
Vehicle Network Gateways
The TJA1041T/N1 can form the high-speed CAN side of a gateway connecting separate vehicle network segments. One CAN controller manages protocol activity on the selected bus, while the TJA1041 handles differential transmission and reception at up to 1 Mbit/s. This separation keeps physical-layer behavior separate from message filtering, diagnostic handling, and gateway software. For a new production design, lifecycle risk should be resolved through NXP's discontinuance information and a structured request for current supply. PCB routing must preserve the intended bus-impedance path and provide a low-impedance ground reference.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for TJA1041T/N1 — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | TJA1041T/CM,118 | TJA1050T/N1 |
|---|---|---|---|
| Package | SOIC-14 (14-SO) | SOIC-14 (14-SO) | SOIC |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Product Type | High-speed CAN transceiver | High-speed CAN transceiver | High-speed CAN interface |
| Supported Data Rate | Up to 1 Mbit/s | 1 Mbit/s | 1 Mbit/s |
| Primary Application | Automotive high-speed CAN | High-speed CAN interface | High-speed CAN interface |
| Mounting Style | SMD/SMT | SMD/SMT | SMD/SMT |
Pangunahing mga Pagkakaiba
- Established 1 Mbit/s automotive high-speed CAN positioning (kumpara saTJA1050T/N1)
- Standard N1 ordering configuration (kumpara saTJA1041T/CM,118)
- Single 14-SO high-speed CAN transceiver (kumpara saTJA1041T/CM,118)
Talaan ng Disenyo
Route CANH and CANL as a closely coupled differential pair, referencing the PCB ground plane. Avoid long stubs, test pads that break coupling, and unnecessary vias. Keep the transceiver, its CAN controller, and the bus-line conditioning components close together so that transmit and receive paths remain compact. The manufacturer's application circuit should be used to determine trace geometry and the location of any common-mode choke.
Do not assume that a 14-pin CAN transceiver can be replaced solely because the package matches. Verify TXD, RXD, ground, supply, stabilization, mode-control, and no-connect assignments against the manufacturer pin table. In particular, TJA1041T/CM,118 adds standby and sleep-mode characteristics, and TJA1050T/N1 may differ in logic-pin implementation. Confirm propagation delay and mode behavior before approving a substitution.
Place the transceiver's required supply-decoupling components close to their associated pins and follow the manufacturer network recommendation. Keep switching regulators, inductors, and high-current return paths away from the CAN receive path to reduce differential and common-mode noise. If the bus requires a split termination or common-mode choke, select its values and placement according to the manufacturer's application guidance rather than general-purpose rules.
Evaluate transceiver power dissipation from the actual supply voltage, dominant current, and bus activity rather than from a nominal output-current rating alone. The 14-SO package should be placed on a PCB with an appropriate copper area and solid ground reference. Confirm the manufacturer's operating-temperature limits and maximum electrical ratings for the selected grade, particularly for automotive applications exposed to temperature extremes.
End-of-Life status should be treated as a supply-planning constraint. Record the exact ordering suffix, quantity, date-code preference, inspection level, and traceability requirements when requesting supply. Do not substitute another TJA1041 packing suffix or family member without engineering approval, because the ordering code can represent a distinct mode configuration even when the package and headline CAN data rate are identical.
Impormasyon ng Pagsunod sa Kautusan
The NXP product page provides environmental quality and lifecycle information, but the verified product records do not explicitly state the required compliance statuses. No compliance claim should be inferred from the automotive application description.